Influence of the tert‐dodecyl mercaptan content in poly(acrylonitrile‐butadiene‐styrene) on properties of chlorinated polyvinyl chloride/poly(acrylonitrile‐butadiene‐styrene) blends

A series of poly(acrylonitrile‐butadiene‐styrene) (ABS) grafting modifiers were synthesized by emulsion grafting poly(acrylonitrile‐styrene) (SAN) copolymer onto polybutadiene (PB) latex rubber particles. The chain transfer reagent tert‐dodecyl mercaptan (TDDM) was used to regulate the grafting degree of ABS and the molecular weight of SAN copolymers. By blending these ABS modifiers with Chlorinated polyvinyl chloride (CPVC) resin, a series of CPVC/ABS blends were obtained. The morphology, compatibility, and the mechanical properties of CPVC/ABS blends were investigated. The scanning electron microscope (SEM) studies showed that the ABS domain all uniformly dispersed in CPVC matrix. Dynamic mechanical analyses (DMA) results showed that the compatibility between CPVC and SAN became enhanced with the TDDM content. From the mechanical properties study of the CPVC/ABS blends, it was revealed that the impact strength first increases and then decreases with the TDDM content, which means that the compatibility between CPVC and the SAN was not the only requirement for maximizing toughness. The decreasing of tensile strength and the elongations might attribute to the lower entanglement between chains of CPVC and SAN. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Structure–properties relationship in toughening of poly(butylene terephthalate) with core–shell modifier

The performance of acrylonitrile–butadiene–styrene (ABS) core–shell modifier with different grafting degree, acrylonitrile (AN) content, and core–shell ratio in toughening of poly(butylene terephthalate) (PBT) matrix was investigated. Results show PBT/ABS blends fracture in ductile mode when the grafting degree is high, and with the decrease of grafting degree PBT/ABS blends fracture in a brittle way. The surface of rubber particles cannot be covered perfectly for ABS with low grafting degree and agglomeration will take place; on the other hand, the entanglement density between SAN and PBT matrix decreases because of the low grafting degree, inducing poor interfacial adhesion. The compatibility between PBT and ABS results from the strong interaction between PBT and SAN copolymer and the interaction is influenced by AN content. Results show ABS cannot disperse in PBT matrix uniformly when AN content is zero and PBT/ABS fractures in a brittle way. With the addition of AN in ABS, PBT/ABS blends fracture in ductile mode. The core–shell ratio of ABS copolymers has important effect on PBT/ABS blends. When the core–shell ratio is higher than 60/40 or lower than 50/50, agglomeration or cocontinuous structure occurs and PBT/ABS blends display lower impact strength. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 5363–5371, 2006     

Toughness,dynamic mechanical property,and morphology of polyvinylchloride/acrylonitrile‐styrene‐butyl acrylate blends

Acrylonitrile‐styrene‐butyl acrylate (ASA) graft copolymers with different acrylonitrile (AN) contents, the core‐shell ratio, and tert‐dodecyl mercaptan (TDDM) amounts were synthesized by seed emulsion polymerization. Polyvinylchloride (PVC)/ASA blends were prepared by melt blending ASA graft copolymers with PVC resin. Then the toughness, dynamic mechanical property, and morphology of the PVC/ASA blends were investigated. The results indicated that the impact strength of the PVC/ASA blends increased and then decreased with the increase of the AN content in poly(styrene‐co‐acrylonitrile (SAN) copolymer, and increased with the increase of the core‐shell ratio of ASA. It was shown that brittle‐ductile transition of PVC/ASA blends was dependent on poly(butyl acrylate) (PBA) rubber content in blends and independent of AN content in SAN copolymer. The introduction of TDDM made the toughness of PVC/ASA blends poor. Dynamic mechanical analysis (DMA) curves exhibited that PVC and SAN copolymers were immiscible over the entire AN composition range. From scanning electron microscopy (SEM), it was found that the dispersion of ASA in PVC/ASA blends was dependent on the AN content in SAN copolymer and TDDM amounts. J. VINYL ADDIT. TECHNOL., 22:43–50, 2016. © 2014 Society of Plastics Engineers     

Effect of compatibilizer on morphology and mechanical properties of TPU/SAN blends

Melt blends of thermoplastic polyurethane (TPU) and Poly(styrene‐co‐acrylonitrile), (SAN) of various compositions were prepared using a two‐roll mill. Two blends of composition 70:30 and 50:50 TPU/SAN were selected for compatibility studies. The compatibility effect of SMA on these incompatible blends was studied. The morphology and physical properties of blends were investigated using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), Fourier transform infrared spectra (FTIR) and mechanical properties. TPU/SAN/SMA 70:30:5 showed better compatibility than other blend ratios.     

Effect of matrix SAN in ABS/PMMA blends

The effect of the molecular weight and acrylonitrile (AN) content of the styrene–acrylonitrile copolymer (SAN) on the morphology, mechanical properties, and rheological properties of acrylonitrile–butadiene–styrene terpolymer/poly(methyl methacrylate) (ABS)/PMMA (60/40 by weight) blends were studied. When the AN content of matrix SAN (32%) was close to that of graft SAN (30%) AN, rubber particles existed separately. However, with matrix SAN having 35% AN, rubber particles showed tendency to agglomerate each other. With increasing molecular weight of matrix SAN, impact strength, ultimate elongation, and abrasion resistance of the blend generally increased. Yield strength increased with molecular weight at a constant AN content of matrix SAN, and it decreased with the decrease of AN content in spite of the increasing molecular weight of SAN. Melt properties, rather than the morphological and mechanical properties, were more sensitive to the AN content, rather than the molecular weight of matrix SAN. © 1994 John Wiley & Sons, Inc.     

Morphology and physical properties of SAN/NBR blends: The effect of AN content in NBR

Poly(styrene‐co‐acrylonitrile) (SAN), of which the content of acrylonitrile (AN) repeating unit is 32 wt % (SAN32), was blended with poly(butadiene‐co‐acrylonitrile) (NBR). The effects of AN repeating unit content in NBR on the miscibility, morphology, and physical properties of SAN32/NBR (70/30 by weight) blends were studied. Differential scanning calorimetry and the morphology observed by transmission electron microscopy showed that the miscibility between SAN32 and NBR was increased as the AN content in NBR was increased up to 50 wt %. The impact strength and some other mechanical properties of the blends had the maximum value when the AN content in NBR was 34 wt %. In the measurement of viscoelasticity at melt state, SAN32/NBR blends showed yield behavior at low shear rate, and this behavior was most evident when the AN content in NBR was 34 wt %. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1861–1868, 2000     

Effect of maleic anhydride grafted polybutadiene on the compatibility of polyamide 66/acrylonitrile‐butadiene‐styrene copolymer blend

The addition of maleic anhydride grafted polybutadiene (PB‐g‐MAH) can greatly improve the compatibility of polyamide 66 (PA66)/acrylonitrile‐butadiene‐styrene copolymer (ABS) blends. Unlike the commonly used compatibilizers in polyamide/ABS blends, PB‐g‐MAH is compatible with the ABS particles' core phase polybutadiene (PB), rather than the shell styrene‐acrylonitrile (SAN). The compatibility and interaction of the components in the blends were characterized by Fourier transform‐infrared spectra (FTIR), Molau tests, melt flow index (MFI), dynamic mechanical analyses (DMA), and scanning electron microscopic (SEM) observations. The results show that PB‐g‐MAH can react with the amino end groups in PA66 while entangle with the PB phase in ABS. In this way, the compatibilizer anchors at the interface of PA66/ABS blend. The morphology study of the fracture sections before and after tensile test reveals that the ABS particles were dispersed uniformly in the PA66 matrix and the interfacial adhesion between PA66 and ABS was increased significantly. The mechanical properties of the blends thus were enhanced with the improving of the compatibility. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

PB橡胶粒径对CPVC/PVC/ABS共混体系结构与性能的影响

采用乳液聚合技术合成了一系列不同PB橡胶粒径的ABS核壳改性剂,将其与CPVC、PVC共混,考察了CPVC/PVC/ABS共混物的结构与性能。动态力学分析表明：CPVC与PVC比例为90/10时,CPVC/PVC共混物部分相容,CPVC/PVC/ABS共混物也是部分相容;扫描电子显微镜分析其形态结构表明：共混物中ABS分散受PB橡胶粒径影响,PB橡胶粒径为113 nm的ABS在CPVC中分散最均匀。力学性能测试表明：随着PB橡胶粒径的增加,共混物的冲击强度先增大后减小,拉伸强度并无明显变化。     

PVC／ABS共混体系的相容性与形态结构研究

采用种子乳液聚合技术在聚丁二烯（PB）乳胶粒子上接枝共聚苯乙烯（St）、α-甲基苯乙烯（α—MSt）和丙烯腈（AN）单体,合成了一系列不同AN结合量的ABS和α—MABS接枝共聚物。将其与聚氯乙烯（PVC）树脂熔融共混制得了PVC／AtkS共混物,利用扫描电镜（SEM）、透射电镜（TEM）和动态力学分析仪（DMA）对共混物的相容性和相结构进行了表征。结果发现,在PVC／ABS共混体系中,尽管改变接枝SAN共聚物的AN结合量,PVC和ABS接枝共聚物均为不相容体系;在ABS接枝共聚物中引入α-MSt后,当接枝SAN共聚物的AN结合量为18．7％～23．6％（质量分数）时,共混物在室温以上只存在1个tanδ峰,共混物成为相容体系,当AN结合量达到32．1％（质量分数）时,共混物成为部分相容体系。共混物的相区尺寸明显地依赖于接枝SAN共聚物中的AN结合量,与动态力学性能结果表现出良好的吻合。     

Compatibility of poly(ϵ-caprolactone) (PCL) and poly(styrene-co-acrylonitrile) (SAN) blends. II. The influence of the AN content in SAN copolymer upon blend compatibility

The compatibility of polymer blends of poly(?-caprolactone) (PCL) and poly(styrene-co-acrylonitrile) (SAN) containing various acrylonitrile (AN) contents was studied to evaluate the influences of copolymer composition and PCL concentration upon blend compatibility. Blend compatibility was characterized by the occurence of a single glass transition intermediate between the transitions of the respective pure components. The glass transitions were determined by differential scanning calorimetry (DSC) and dynamic mechanical measurement (Rheovibron). It was found that SAN and PCL form compatible blends when the AN content of SAN ranges from 8% to 28% by weight. These blends are compatible in all proportions except for SAN 28 (AN wt % = 28) and PCL blends containing 70 or 85 wt % PCL. Blends of PCL and SAN were found to be incompatible when the AN content in SAN is greater than 30 wt % or less than 6 wt %. Lower critical solution temperature (LCST) behavior, which can be attributed to phase separation, was found to occur when these blends were heated to elevated temperatures. The cloud point, or phase separation, was found to vary with AN content in SAN and the concentration of SAN in the blend.     

Oxazoline‐containing compatibilizers for polyamide/SAN and polyamide/ABS blends

Polyamide (PA) and acrylonitrile/butadiene/styrene copolymer (ABS) may appear as a mixture in the recycled plastic stream. The incompatibility of these blends results in a blend with poor mechanical properties. The aim of this work is to partially convert the nitrile groups of the acrylonitrile/styrene copolymer (SAN) into oxazoline groups by reaction with aminoethanol (AE). Such modified SAN (SAN‐m) can react with the amine or carboxylic acid end groups of PA, and therefore used as compatibilizers for blends of PA with ABS. SAN‐m was found to reduce the SAN‐domain size in the PA/SAN‐blends. The initial acrylonitrile content of SAN‐m had a strong influence on the degree of conversion into oxazoline groups and on the compatibilizing effect. Mechanical properties of SAN‐m compatibilized PA/ABS blends were investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 449–455, 2002     

Properties of ASA/SAN/NBR ternary blends: effect of AN content in NBR

Abstract

Nitrile–butadiene rubbers (NBRs) with different acrylonitrile (AN) contents were used to toughen acrylonitrile–styrene–acrylic terpolymer/styrene–acrylonitrile copolymer (ASA/SAN) blends. The properties of the ASA/SAN/NBR ternary blends were investigated via dynamic mechanical analysis, heat distortion temperature, Fourier transform infrared spectroscopy and scanning electron microscopy (SEM). The effects of AN content in NBR on physical properties, heat resistance and morphology of the ternary blends were studied. Heat distortion temperature of the blends decreased with increasing AN content of NBR. The impact strength reached the maximum value when 20 phr NBR with 26 wt-%AN content was added. Images (SEM) were in accordance with results of mechanical properties.     

Weld‐line characteristics of polycarbonate/acrylonitrile–butadiene–styrene blends. I. Effect of the processing temperature

The effects of the processing temperature on the morphology and mechanical properties at the weld line of 60/40 (w/w) polycarbonate (PC)/acrylonitrile–butadiene–styrene (ABS) copolymer blends were investigated. The influences of the incorporation of poly(methyl methacrylate) (PMMA) as a compatibilizer and an increase in the viscosity of the dispersed ABS domain phase were also studied. The ABS domain was well dispersed in the region below the V notch, and a coarse morphology in the core region was observed. When tensile stress was applied perpendicularly to the weld line, the fracture propagated along the weak region behind the weld part; there, the domain phase coalescence was significant because of the poor compatibility between PC and styrene–acrylonitrile (SAN). Phase coalescence became severe, and so the mechanical strength of the welded specimen decreased with an increasing injection‐molding temperature. The domain morphology became stable and the mechanical strength increased as the viscosity of the domain phase increased or some SAN was replaced with PMMA. That the morphology was well distributed behind the weld line and the mechanical properties of PC/ABS/PMMA blends were improved was attributed to the compatibilizing effect of PMMA. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 689–699, 2005     

Dynamic‐mechanical analysis of MWNTs‐filled PC/ABS blends

In a systematic manner, the roles of MWNTs as filler and styrene acrylonitrile copolymer‐graft‐maleic anhydride (SAN‐MA) as compatibilizer, individually and together, on dynamic‐mechanical behavior of polycarbonate (PC)‐rich/acrylonitrile butadiene styrene terpolymer (ABS) blend were studied. The investigations were performed using small‐scale mixing in a one‐step procedure with a fixed MWNTs content of 0.75 wt% and a blend composition of PC/ABS = 70/30 w/w. PC/SAN blends and nanocomposites as simpler model system for PC/ABS were also studied to reveal the role of the rubbery polybutadiene (PB) fraction. It is found that the tendency of MWNTs to localize within the PC component in compatibilized PC/ABS was lower than in compatibilized PC/SAN blends. Dynamic mechanical analysis (DMA) revealed the dual role of SAN‐MA as blend compatibilizer and also promoter of MWNTs migration towards PC, where SAN‐MA to MWNTs weight ratio varied between 1 and 4. At the compatibilizer/MWNTs weight ratio of 1, MWNTs localized in PC component of the blends whereas increasing the compatibilizer/MWNTs ratio to 4 led to migration of MWNTs toward SAN or ABS component. In DMA studies, loss modulus normalization of the nanocomposites revealed the coexistence of mobilized and immobilized regions within the nanocomposite structure, as a result of MWNTs and compatibilizer loading. POLYM. ENG. SCI., 54:2696–2706, 2014. © 2014 Society of Plastics Engineers     

Influence of acrylic content in PBA‐SAN on the mechanical properties of PBA‐SAN and PBA‐SAN/SAN blends

The effects of different acrylic rubber (PBA) contents in core‐shell structured rubbery acrylate‐g‐poly (styrene‐acrylonitrile) (PBA‐SAN) on the mechanical properties of PBA‐SAN and PBA‐SAN/SAN blends were systematically investigated. Fourier transform‐infrared spectroscopy (FTIR) and scanning electron microscope (SEM) were used to characterize the structure and morphology of PBA‐SAN and PBA‐SAN/SAN blends, respectively. It was found that the mechanical properties of PBA‐SAN and PBA‐SAN/SAN blends strongly depended on the PBA content: largely improved impact strength and elongation at break were observed when adding PBA‐SAN with high PBA content. However, the loss in rigidity and heat distortion temperature were accompanied. Specifically, both PBA‐SAN and PBA‐SAN/SAN blends with 60 wt% PBA exhibited a good balance between toughness and rigidity, which indicating PBA‐SAN with 60 wt% PBA was the most suitable impact modifier. J. VINYL ADDIT. TECHNOL., 24:262–267, 2018. © 2016 Society of Plastics Engineers     

Study of compatibility between aliphatic polyketone terpolymer and poly(styrene-r-acrylonitrile)

Compatibility studies have been conducted for polyketone (PK) and styrene–acrylonitrile (SAN) blends in which SAN polymers have different acrylonitrile (AN) contents. Measurements of mechanical properties exhibit the immiscibility of PK/SAN blends. Glass transition temperature shifts and width broadening of the glass transition mean partial compatibility in the amorphous region of the PK/SAN blends. Peak shifts of the CO functional group are larger for PK/SAN48 than that of PK/SAN40 blend. In morphological observations, the dispersed domains appear more refined for the PK/SAN48 blend and the PK/SAN48 blend has better boundary adhesion between the two phases. The Flory–Huggins interaction parameters simulated for the PK/SAN mixture were at a low level and the PK/SAN48 blend showed lower values than the PK/SAN40 blend. This means that the PK/SAN polymer blend is partially compatible in the amorphous region. The level of compatibility tends to increase as the AN content of the SAN polymer increases. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48743.     

Effects of tetramethylpolycarbonate‐block‐poly(styrene‐co‐acrylonitrile) copolymers containing various amounts of acrylonitrile on the interfacial properties of polycarbonate and poly(styrene‐co‐acrylonitrile) blends

Tetramethylpolycarbonate‐block‐poly(styrene‐co‐acrylonitrile) (TMPC‐block‐SAN) block copolymers containing various amounts of acrylonitrile (AN) were examined as compatibilizers for blends of polycarbonate (PC) with poly(styrene‐co‐acrylonitrile) (SAN) copolymers. To explore the effects of block copolymers on the compatibility of PC/SAN blends, the average diameter of the dispersed particles in the blend was measured with an image analyzer, and the interfacial properties of the blends were analyzed with an imbedded fibre retraction technique and an asymmetric double‐cantilever beam fracture test. Reduction in the average diameter of dispersed particles and effective improvement in the interfacial properties was observed by adding TMPC‐block‐SAN copolymers as compatibilizer of PC/SAN blend. TMPC‐block‐SAN copolymer was effective as a compatibilizer when the difference in the AN content of SAN copolymer and that of SAN block in TMPC‐block‐SAN copolymer was less than about 10 wt%. Copyright © 2004 Society of Chemical Industry     

Compatibility enhancement of ABS/PVC blends

The compatibilizing effect of poly(styrene-co-acrylonitrile) (SAN) whose acrylonitrile (AN) content is 25 wt % (SAN 25) in poly(acrylonitrile-co-butadiene-co-styrene) (ABS)/poly(vinyl chloride) (PVC) blend was studied when the AN content of the matrix SAN in ABS was 35 wt % (SAN 35). When some amount of matrix SAN 35 was replaced by SAN 25 in a ABS/PVC (50/50 by weight) blend, the mixed phase of SAN and PVC at the interface was thickened, and about a twofold increase of impact strength was observed. The changes in morphology, dynamic mechanical properties, and rheological properties by the compatibilizing effect of SAN 25 were observed. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 705–709, 1998     

Effects of the polybutadiene/poly(styrene‐co‐acrylonitrile) ratio in a polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) impact modifier on the morphology and mechanical behavior of acrylonitrile–butadiene–styrene blends

Polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) (PB‐g‐SAN) impact modifiers with different polybutadiene (PB)/poly(styrene‐co‐acrylonitrile) (SAN) ratios ranging from 20.5/79.5 to 82.7/17.3 were synthesized by seeded emulsion polymerization. Acrylonitrile–butadiene–styrene (ABS) blends with a constant rubber concentration of 15 wt % were prepared by the blending of these PB‐g‐SAN copolymers and SAN resin. The influence of the PB/SAN ratio in the PB‐g‐SAN impact modifier on the mechanical behavior and phase morphology of ABS blends was investigated. The mechanical tests showed that the impact strength and yield strength of the ABS blends had their maximum values as the PB/SAN ratio in the PB‐g‐SAN copolymer increased. A dynamic mechanical analysis of the ABS blends showed that the glass‐transition temperature of the rubbery phase shifted to a lower temperature, the maximum loss peak height of the rubbery phase increased and then decreased, and the storage modulus of the ABS blends increased with an increase in the PB/SAN ratio in the PB‐g‐SAN impact modifier. The morphological results of the ABS blends showed that the dispersion of rubber particle in the matrix and its internal structure were influenced by the PB/SAN ratio in the PB‐g‐SAN impact modifiers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2165–2171, 2005     

Effects of addition of acrylic compatibilizer on the morphology and mechanical behavior of amorphous polyamide/SAN blends

Amorphous polyamide (aPA)/acrylonitrile‐styrene copolymer (SAN) blends were prepared using methyl methacrylate‐maleic anhydride copolymer MMA‐MA as compatibilizer. The aPA/SAN blends can be considered as a less complex version of the aPA/ABS (acrylonitrilebutadiene‐styrene) blends, due to the absence of the ABS rubber phase in the SAN material. It is known that acrylic copolymer might be miscible with SAN, whereas the maleic anhydride groups from MMA‐MA can react in situ with the amine end groups of aPA during melt blending. As a result, it is possible the in situ formation of aPA‐g‐MMA‐MA grafted copolymers at the aPA/SAN interface during the melt processing of the blends. In this study, the MA content in the MMA‐MA copolymer and its molecular weight was varied independently and their effects on the blend morphology and stress–strain behavior were evaluated. The morphology of the blends aPA/SAN showed a minimum in the SAN particle size at low amounts of MA in the compatibilizer, however, as the MA content in the MMA‐MA copolymer was increased larger SAN particle sizes were observed in the systems. In addition, higher MA content in the compatibilizer lead to less ductile aPA/SAN blends under tensile testing. The results shown the viscosity ratio also plays a very important role in the morphology formation and consequently on the properties of the aPA/SAN blends studied. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010