Comparative study of micro- and nano-ZnO reinforced UHMWPE composites under dry sliding wear

This is a comparative study between ultra-high molecular weight polyethylene (UHMWPE) reinforced with micro-zinc oxide (ZnO) and nano-ZnO under different filler loads. These composites were subjected to dry sliding wear test under abrasive conditions. The micro- and nano-ZnO/UHMWPE composites were prepared by using a hot compression mould. The wear and friction behaviours were monitored using a pin-on-disc (POD) test rig. The pin-shaped samples were slid against 400 grit SiC abrasive papers, which were pasted, on the stainless steel disc under dry sliding conditions. The worn surfaces and transfer film formed were observed under the scanning electron microscope (SEM). Experimental results showed that UHMWPE reinforced with micro- and nano-ZnO would improve the wear behaviour. The average coefficient of friction (COF) for both micro- and nano-ZnO/UHMWPE composites were comparable to pure UHMWPE. The weight loss due to wear for nano-ZnO/UHMWPE composites are lower compared to micro-ZnO/UHMWPE and pure UHMWPE. The optimum filler loading of nano-ZnO/UHMWPE composites is found to be at 10 wt%. The worn surface of ZnO/UHMWPE composites shows the wear mechanisms of abrasive and adhesive wear. Upon reinforcement with micro- and nano-ZnO, the abrasive and adhesive wear of worn surfaces transited from rough to smooth.     

Tribology characteristics of magnesium alloy AZ31B and its composites

In this paper, wear characteristics of magnesium alloy, AZ31B, and its nano-composites, AZ31B/nano-Al₂O_3, processed by the disintegrated melt deposition technique are investigated. The experiments were carried out using a pin-on-disk configuration against a steel disk counterface under different sliding speeds of 1, 3, 5, 7 and 10 m/s for 10 N normal load, and 1, 3 and 5 m/s for 30 N normal load. The worn samples and wear debris were then examined under a field emission scanning electron microscopy equipped with an energy dispersive spectrometer to reveal its wear features. The wear test results show that the wear rates of the composites are gradually reduced over the sliding speed range for both normal loads. The composite wear rates are higher than that of the alloy at low speeds and lower when sliding speed further increased. The coefficient of friction results of both the alloy and composites are in the range of 0.25–0.45 and reaches minimums at 5 m/s under 10 N and 3 m/s under 30 N load. Microstructural characterization results established different dominant mechanisms at different sliding speeds, namely, abrasion, delamination, oxidation, adhesion and thermal softening and melting. An experimental wear map was then constructed.     

Effect of SiC particles on the friction and wear behavior of Ti3Si(Al)C2-based composites

The non-lubricated, sliding friction and wear behavior of Ti₃Si(Al)C₂ and SiC-reinforced Ti₃Si(Al)C₂ composites against AISI 52100 bearing steel ball were investigated using a ball-on-flat, reciprocating tribometer at room temperature. The contact load was varied from 5 to 20 N. For monolithic Ti₃Si(Al)C₂, high friction coefficients between 0.61 and 0.90 and wear rates between 1.79 × 10⁻³ and 2.68 × 10⁻³ mm³ (N m)⁻¹ were measured. With increasing SiC content in the composites, both the friction coefficients and the wear rates were significantly decreased. The friction coefficients reduced to a value between 0.38 and 0.50, and the wear rates to between 2.64 × 10⁻⁴ and 1.93 × 10⁻⁵ mm³ (N m)⁻¹ when the SiC content ranged from 10 to 30 vol.%. The enhanced wear resistance of Ti₃Si(Al)C₂ is mainly attributed to the facts that the hard SiC particles inhibit the plastic deformation and fracture of the soft matrix, the oxide debris lubricate the counterpair, and the wear mode converts from adhesive wear to abrasive wear during dry sliding.     

Effects of carbon fiber length on the tribological properties of paper-based friction materials

Four kinds of paper-based friction materials reinforced with carbon fibers of 100, 400, 600 and 800 μm were prepared by paper-making processes. Experimental results showed that the friction materials became porous with fiber length increasing. The friction torque curves were flat except the sample with 100 μm fibers. The wear rate of the sample with 100 μm fibers was only 1.40×10⁻⁵ mm³/J. Tiny debris and fine scratches formed in the worn surface were the reason for excellent wear resistance of friction pairs with 100 μm fibers. The friction pairs with 400, 600 and 800 μm fibers showed typically abrasive wear and fatigue wear.     

Friction and wear behaviors of C/C-SiC composites containing Ti3SiC2

In the present paper, friction and wear behaviors of a carbon fiber reinforced carbon–silicon carbide–titanium silicon carbide (C-SiC–Ti₃SiC₂) hybrid matrix composites fabricated by slurry infiltration and liquid silicon infiltration were studied for potential application as brake materials. The properties were compared with those of C/C-SiC composites. The composites containing Ti₃SiC₂ had not only higher friction stability coefficient but also much higher wear resistance than C/C-SiC composites. At an initial braking speed of 28 m/s under 0.8 MPa pressure, the weight wear rate of the composites containing 5 vol% Ti₃SiC₂ was 5.55 mg/cycle, which was only one-third of C/C-SiC composites. Self-lubricious film-like debris was formed on the composites containing Ti₃SiC₂, leading to the improvement of friction and wear properties. The effect of braking speed and braking pressure on the tribological properties of modified composites were investigated. The average friction coefficient was significantly affected by braking speed and braking pressure, but the wear rate was less affected by braking pressure.     

Tribological behaviors of Ti–6Al–4V modified by chemical methods

In order to improve the tribological properties of titanium-based implants, sodium hydroxide (NaOH), hydrogen peroxide (H₂O₂) solutions, sol–gel hydroxyapatite (HA) film, thermal treatment and combined methods of NaOH solution/HA film, H₂O₂ solution/HA film are used to modify the surfaces of Ti–6Al–4V (coded TC4). The chemical states of some typical elements in the modified surfaces were detected by means of X-ray photoelectron spectroscopy (XPS). The tribological properties of modified surfaces sliding against an AISI52100 steel ball were evaluated on a reciprocating friction and wear tester. As the results, complex surfaces with varied components are obtained. All the methods are effective in improving the wear resistance of Ti–6Al–4V in different degrees. Among all, the surface modified by the combined method of NaOH solution/HA film gives the best tribological performances. The friction coefficient is also greatly reduced by the modification of NaOH solution. The order of the wear resistance under 3 N is as following: Ti–NaOH–HA>Ti–NaOH>Ti–HA>Ti–H₂O₂–HA>Ti–H₂O₂ >Ti–500; under 1 N is Ti–HA, Ti–NaOH–HA>Ti–NaOH. For Ti–H₂O₂, a very low friction coefficient and long wear life over 2000 passes is obtained under 1 N. SEM observation of the morphologies of worn surfaces indicates that the wear of TC4 is characteristic of abrasive wear. Differently, abrasion, plastic deformation and micro–crack dominate the wear of Ti–HA; slight abrasive wear dominate the wear mechanism of Ti–NaOH and microfracture and abrasive wear for Ti–NaOH–HA and Ti–H₂O₂–HA, while the sample modified by thermal treatment is characterized by sever fracture. The superior friction reduction and wear resistance of HA films are greatly attributed to the slight plastic deformation of the film. NaOH solution is superior in improving the wear resistance and decreasing the friction coefficient under relative higher load (3 N) and H₂O₂ is helpful to reduce friction and wear under relatively lower load (1 N). Combined method of Ti–NaOH–HA is suggested to improve the wear resistance of Ti–6Al–4V for medial applications under fretting situations.     

WC–ZrO2 composites: processing and unlubricated tribological properties

In the present work, we report the processing and properties of WC–6 wt.% ZrO₂ composites, densified using the pressureless sintering route. The densification of the WC–ZrO₂ composites was carried out in the temperature range of 1500–1700 °C with varying time (1–3 h) in vacuum. The experimental results indicate that significantly high hardness of 22–23 GPa and moderate fracture toughness of ∼5 MPa m^1/2 can be obtained with 2 mol% Y-stabilized ZrO₂ sinter-additive, sintered at 1600 °C for 3 h. Furthermore, the friction and wear behavior of optimized WC–ZrO₂ composite is investigated on a fretting mode I wear tester. The tribological results reveal that a moderate coefficient of friction in the range from 0.15 to 0.5 can be achieved with the optimised composite. An important observation is that a transition in friction and wear with load is noted. The dominant mechanisms of material removal appear to be tribochemical wear and spalling of tribolayer.     

Effect of crosslinking on tribological behavior of tung oil-based polymers

In this study, the tribological properties of tung oil-based polymers synthesized by the cationic copolymerization of tung oil with divinylbenzene and styrene are evaluated as a function of crosslinking density. Tribological measurements were performed using a ball-on-flat reciprocating microtribometer on samples with three crosslinking densities of 20%, 30% and 40% by weight of the crosslinking agent. Friction and wear characteristics during dry sliding were evaluated using a spherical (1.2 mm radius) silicon nitride probe as well as a conical (100 μm radius, 90° cone angle) diamond probe. Microscale friction behavior was evaluated from single strokes at ramped normal loads, whereas wear experiments were evaluated from 100 to 500 reciprocating cycles at fixed normal loads. Elastic modulus and hardness information were evaluated using nanoindentation tests. Scanning electron microscopy of wear tracks was used to elucidate deformation mechanisms in the various samples. All samples showed friction coefficients ranging from 0.06 to 0.49. It was found that a higher crosslinking density resulted in lower abrasive wear due to increased hardness. These results provide some insight into the friction and wear behavior of tung oil-based polymers.     

Wear behavior of Cu–La2O3 composite with or without electrical current

A new type Cu–La₂O₃ composite was fabricated by internal oxidation method using powder metallurgy. Sliding wear behavior of the Cu–La₂O₃ composites was studied by using a pin-on-disk wear tester under dry sliding conditions with or without electrical current, rubbing against GCr15 type bearing steel disk at a constant sliding speed of 20 m/s. The influence of varying applied load and electrical current was investigated. The worn surfaces were examined using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) to determine the wear mechanisms. The results showed the Cu–La₂O₃ composites had an electrical conductivity of 81.9% IACS (International Annealed Copper Standard, 100% IACS = 58 MS/m) and a hardness of HV105. The wear rate of the Cu–La₂O₃ composite pins increased with the increase in the electrical current at high sliding speed. The main wear mechanisms of the Cu–La₂O₃ composites were found to be adhesive wear, abrasive wear and arc erosion.     

Sliding wear performance of nano-SiO2/short carbon fiber/epoxy hybrid composites

In the present work, epoxy based composites filled with hybrid nano-SiO₂ particles and short pitch based carbon fiber were prepared. Copolymer of styrene and maleic anhydride was grafted onto the nanoparticles prior to the compounding so that the nanoparticles can be covalently connected to the composites’ matrix through the reaction between anhydride and epoxide groups during curing. Consequently, the nano-SiO₂/matrix interfacial interaction was enhanced. By evaluating sliding wear properties of the composites as a function of the components concentrations, positive synergetic effect was found. That is, both wear rate and friction coefficient of the hybrid composites were significantly lower than those of the composites containing individual nano-SiO₂ or short carbon fiber. The composite with 4 wt.% nano-SiO₂ and 6 wt.% carbon fiber offered the greatest improvement of the tribological performance. Compared to the results of hybrid composites reported so far, the above composite is characterized by relatively lower filler content, which would facilitate processing in practice. Increased surface hardness, lubricating effect of the sheet-like wear debris reinforced by nano-SiO₂ and rapidly formed transfer film were believed to be the key issues accounting for the remarkable wear resisting and friction reducing behaviors.     

Abrasive wear behavior of boronized AISI 8620 steel

In this study, AISI 8620 steel was boronized using the solid state boronizing technique. Processes were carried out at the temperatures of 850, 900 and 950 °C for 2, 4 and 6 h of treatment. Abrasive wear behavior of the samples boronized at different temperatures and treatment durations have been examined. Using boronized and unboronized samples, abrasive tests were conducted using pin on disc test apparatus. 80 and 120 mesh aluminum oxide (Al₂O₃) abrasive papers were used in the abrasion experiments and the samples were subjected to abrasion under 10, 20 and 30 N loads. Boronized steels exhibited an improvement in abrasive wear resistance reaching up to 500%. Microstructures and wear surfaces of the samples were inspected using SEM microscopy. SEM examinations revealed that the thickness of the boride layer on the steel surfaces changes with changing process durations and temperatures. The presence of boride formed in the borided layer at the surface of the steels were determined by XRD analysis and microhardness values of the iron borides (FeB, Fe₂B) formed on the steel surface were found to be over 1600 HV.     

Influence of orientation and volume fraction of Aramid fabric on abrasive wear performance of polyethersulfone composites

In case of fabric reinforced composites of specialty polymers influence of orientation of fabric and its volume fraction on tribo-behaviour is sparingly studied. In our earlier work, we have reported on the influence of amount of Aramid fabric (AF) in polyethersulfone (PES) on abrasive wear performance. However, orientation effect of fabric with respect to abrading plane was not investigated. In this work three orientations of composites of PES containing Aramid (Kevlar 29) fabric with three concentrations 64, 72 and 83 wt.% were selected to study the influence on abrasive wear performance. Composites developed by compression molding technique were characterized for their mechanical and physical properties. The abrasive wear performance of the composites was evaluated by abrading 10 mm × 10 mm × 10 mm sample against silicon carbide (SiC) paper under various loads and two grades of abrasive papers. The fabric reinforcement enhanced the abrasive wear resistance of PES significantly (approximately 1.35–9.46 times depending on the operating conditions). It was observed that 83% fabric composite showed the highest resistance to abrasive wear and impact along with the best tensile strength and elongation properties. Its flexural strength and ILSS values, however, were the lowest. Sixty-four percent fabric composite, on the other hand, showed an exactly reverse trend among the three composites. Among the three orientations, fibres in normal and parallel (N–P) and normal and anti-parallel (N–AP) direction with respect to sliding plane proved to impart maximum wear resistance. N–P was best for light loads while N–AP was best for high loading conditions. Orientation parallel and anti-parallel (P–AP) was least beneficial in this respect. Moreover, the extent of improvement very much depended on the operating parameters such as grit size and load. Benefits endowed due to reinforcement were higher at less coarse grade paper. With increase in load, however, wear rate of composites with N–P orientation increased and for other two orientations it decreased. Thus, for severe operating conditions, N–AP orientation proved to be most beneficial. SEM studies proved supporting for understanding the influence of orientation on wear performance.     

Sliding/rolling wear performance of plasma nitrided H11 hot working steel

H11 steel discs were tested by considering sliding/rolling friction under dry and lubricated conditions. The H11 discs were plasma nitrided at 500 °C and 550 °C for 9 h. Wear tests were conducted at different slip ratios of 1.79%, 10.53% and 22.22%. The test loads were 100 N, 150 N and 200 N. It was determined that plasma-nitrided H11 discs had a surface hardness of 1200–1400 HV0.1. Plasma nitriding produced wear performance much higher than those of the un-nitrided but hardened samples. The wear mechanism of the plasma-nitrided discs was a mixture of adhesive wear, abrasive wear and plastic yielding.     

Cutting forces,tool wear and surface finish in high speed diamond machining

We have investigated the cutting forces, the tool wear and the surface finish obtained in high speed diamond turning and milling of OFHC copper, brass CuZn39Pb3, aluminum AlMg5, and electroless nickel. In face turning experiments with constant material removal rate the cutting forces were recorded as a function of cutting speed between v_c = 150 m/min and 4500 m/min revealing a transition to adiabatic shearing which is supported by FEM simulations of the cutting process. Fly-cutting experiments carried out at low (v_c = 380 m/min) and at high cutting speed (v_c = 3800 m/min) showed that the rate of abrasive wear of the cutting edge is significantly higher at ordinary cutting speed than at high cutting speed in contrast to the experience made in conventional machining. Furthermore, it was found that the rate of chemically induced tool wear in diamond milling of steel is decreasing with decreasing tool engagement time per revolution. High speed diamond machining may also yield an improved surface roughness which was confirmed by comparing the step heights at grain boundaries obtained in diamond milling of OFHC copper and brass CuZn39Pb3 at low (v_c = 100 m/min) and high cutting speed (v_c = 2000 m/min). Thus, high speed diamond machining offers several advantages, let alone a major reduction of machining time.     

Fretting wear behaviors of nanometer Al2O3 and SiO2 reinforced PEEK composites

The influence of diameter and content of Al₂O₃ particles on the tribological behaviors under fretting wear mode was investigated. The surface of PEEK composite and steel ball were examined by SEM and EDS, to identify the topography of wear scar and analyze the distribution of chemical elements in the friction counterparts, respectively. It can be found that the filling of Al₂O₃ powder improves the fretting wear resistance of PEEK composite. With the increase of Al₂O₃ diameter, the area of wear scar on specimen increases first and decreases afterward. However, the wear of composites increases monotonically with increasing Al₂O₃ content. Although the filling of 10 wt.% and 200 nm PTFE powder in PEEK makes the lowest wear of all specimens, no synergistic effect was found when Al₂O₃ and PTFE were filled into PEEK composite together. For the friction pair of PEEK composite and steel ball, abrasive wear and adhesive wear dominate the fretting wear mechanism during fretting. Thermal effect plays a very important role during fretting; thus the property of temperature resistance for polymer material would affect the wear degree on the surface of wear scar.     

Effect of pH on wear and friction of silicon nitride sliding against alumina in water

The influence of the pH in water lubricated sliding contacts was evaluated in terms of friction and wear. The experiments were carried out using a ball-on-disc setup. Si₃N₄ balls and Al₂O₃ discs were tested at temperature of (22±2) °C, sliding speed of (1.00±0.03) m/s and normal load of (54.25±0.17) N. Eight types of water with pHs varying from 3 to 12 were used as lubricant. The running-in period, friction coefficient and wear-volume were shown to be nearly independent of the initial pH values within the DLVO range (4≤pH≤10), since at these range the water׳s pH tends to the same value (7.6±0.3) during the test. Superlubricity could be reached with negligible wear by properly setting the electrochemical properties and operating conditions of the tribosystem.     

Wear reducing effects and temperature dependence of tribolayer formation in harsh environment

Certain materials show a tribolayer formation especially at enhanced temperatures in abrasive environment, building a wear protection layer with the abrasive on the surface. Three materials with different microstructures were tested in three-body abrasive and impact/abrasive environments at temperatures up to 700 °C to investigate tribolayer formation. Optical and electron microscopical methods were used for wear qualification. Furthermore, hot hardness tests were performed up to 700 °C to investigate the influence of hardness drop on tribolayer formation.It was shown that no significant tribolayer formation occurs on grey cast iron, whereas other materials form tribolayers. Generally, tribolayer formation increases with increasing testing temperature, especially for austenitic and ferritic materials. This entails a self-protecting effect and thus superior wear resistance in abrasive environment.     

Improved wear resistance in alumina-PTFE nanocomposites with irregular shaped nanoparticles

Past studies with PTFE nanocomposites showed up to 600× improvements in wear resistance over unfilled PTFE with the addition of Al₂O₃ nanoparticles. Irregular shaped nanoparticles are used in this study to increase the mechanical entanglement of PTFE fibrils with the filler. The tribological properties of 1, 2, 5 and 10 wt.% filled samples are evaluated under a normal pressure and sliding speed of 6.3 MPa and 50.8 mm/s, respectively. The wear resistance was found to improve 3000× over unfilled PTFE with the addition of 1 wt.% nanoparticles. The 5 wt.% sample had the lowest steady state wear rate of K = 1.3 × 10⁻⁷ mm³/N m and the lowest steady friction coefficient with μ = 0.21.     

Characterization and tribological investigation of sol–gel ceramic films on Ti–6Al–4V

SiO₂, TiO₂, and hydroxyapatite (HA) thin films with good biocompatibility were grown on Ti–6Al–4V (coded as TC4) substrate by sol–gel and dip-coating processes from specially formulated sols, followed by annealing at 500 °C The chemical states of some typical elements in the target films were detected by means of X-ray photoelectron spectroscopy (XPS). Atomic force microscopy (AFM) and high-resolution scanning electron microscopy (SEM) are applied to characterize the original unworn films. The tribological properties of thin films sliding against an AISI52100 steel ball were evaluated on a reciprocating friction and wear tester. As the result, the target films composed of nano-particles ranging from 30 nm to 100 nm around were obtained. All the sol–gel ceramic films are superior in resisting wear compared with the TC4 substrate. Among all, HA film shows the best resistance while SiO₂ film shows the worst wear resistance both under higher (3 N) and lower load (1 N). TiO₂ shows good wear resistance under lower load (1 N). SEM observation of the morphologies of worn surfaces indicates that the wear of TC4 is characteristic of abrasive wear. Differently, abrasion, plastic deformation and micro-fracture dominate the wear of ceramic films. The superior friction reduction and wear resistance of HA film is greatly due to the slight plastic deformation of the film. It is supposed that the deformation of the HA film is closely related to the special arrangement of the nano-particles and microstructure. HA film is recommended for clinical application from the point of wear resistance view.     

Break-away friction of PTFE materials in lubricated conditions

This study investigates the tribological characteristics at initiation of sliding (break-away friction) of several polytetrafluoroethylene based materials. Four PTFE composites, pure PTFE, and white metal were tested in a reciprocating tribo-meter with the block on plate configuration against a steel counter-surface. Apparent contact pressure and oil temperature were varied from 1 to 8 MPa and 25 to 85 °C respectively. SEM investigations revealed wear patterns of the PTFE materials and the abrasive nature of hard fillers.Bronze filled, carbon filled, and pure PTFE were found to provide lower break-away friction and less variation over the course of testing and generally superior properties.