Channel width effect for organic thin film transistors using TIPS-pentacene employed as a dopant of poly-triarylamine

The effects of the physical channel width on the characteristics of organic thin film transistors (OTFTs), made with 6,13-bis(triisopropyl-silylethynyl)-pentacene (TIPS-pentacene) embedded into poly-triarylamine (PTAA, hole conductor within an active channel), have been examined in this paper. The devices are estimated by measuring the drain-source current (I_DS) for different contact metals such as Au and Ag, at fixed gate and drain voltages. The results show that the threshold voltage (V_T) and I_DS increase with increasing channel width. Furthermore, it has been observed that the field effect mobility is dependent on V_T, which is influenced by the channel width. The OTFTs, produced using Au and Ag contacts, exhibited the highest values of mobility in the saturation regime, namely 5.44 × 10^?2 and 1.33 × 10^?2 cm²/Vs, respectively.     

Non-functionalized soluble diketopyrrolopyrrole: Simplest p-channel core for organic field-effect transistors

We report the synthesis, characterization and behavior in field-effect transistors of non-functionalized soluble diketopyrrolopyrrole (DPP) core with only a solubilizing alkyl chain (i.e. –C₁₆H₃₃ or –C₁₈H₃₇) as the simplest p-channel semiconductor. The characteristics were evaluated by UV–vis and fluorescence spectroscopy, X-ray diffraction, cyclic voltammetry (CV), thermal analysis, atomic force microscopy (AFM) and density functional theory (DFT) calculation. For top-contact field-effect transistors, two types of active layers were prepared either by a solution process (as a 1D-microwire) or thermal vacuum deposition (as a thin-film) on a cross-linked poly(4-vinylphenol) gate dielectric. All the devices showed typical p-channel behavior with dominant hole transports. The device made with 1D-microwiress of DPP-R18 showed field-effect mobility in the saturation region of 1.42 × 10^?2 cm²/V s with I_ON/I_OFF of 1.82 × 10³. These findings suggest that the non-functionalized soluble DPP core itself without any further functionalization could also be used as a p-channel semiconductor for low-cost organic electronic devices.     

Dry growth of n-octylphosphonic acid monolayer for low-voltage organic thin-film transistors

Dry method for monolayer deposition of n-octylphosphonic acid (C₈PA) on the surface of aluminium oxide (AlO_x) is presented. Vacuum thermal evaporation is employed to deposit initial thickness corresponding to several C₈PA monolayers, followed by a thermal desorption of the physisorbed C₈PA molecules. AlO_x functionalized with such C₈PA monolayer exhibits leakage current density of ～10^?7 A/cm² at 3 V, electric breakdown field of ～6 MV/cm, and a root-mean-square surface roughness of 0.36 nm. The performance of low-voltage pentacene thin-film transistors that implement this dry AlO_x/C₈PA gate dielectric depends on C₈PA desorption time. When the desorption time rises from 25 to 210 min, the field-effect mobility increases from ～0.02 to ～0.04 cm²/V s, threshold voltage rises from ～?1.2 to ～?1.4 V, sub-threshold slope decreases from ～120 to ～80 mV/decade, off-current decreases from ～5 × 10^?12 to ～1 × 10^?12 A, on/off current ratio rises from ～3.8 × 10⁴ to ～2.5 × 10⁵, and the transistor hysteresis decreases from 61 to 26 mV. These results collectively support a two stage model of the desorption process where the removal of the physisorbed C₈PA molecules is followed by the annealing of the defect sites in the remaining C₈PA monolayer.     

2 MeV ion irradiation effects on AlGaN/GaN HFET devices

AlGaN/GaN heterostructure field effect transistors (HFETs) were irradiated with 2 MeV protons, carbon, oxygen, iron and krypton ions with fluences ranging from 1 × 10⁹ cm^?2 to 1 × 10¹³ cm^?2. DC, pulsed I–V characteristics, loadpull and S-parameters of the AlGaN HFET devices were measured before and after irradiation. In parallel, a thick GaN reference layer was also irradiated with the same ions and was characterized by X-ray diffraction, photoluminescence, Hall measurements before and after irradiation. Small changes in the device performance were observed after irradiation with carbon and oxygen at a fluence of 5 × 10¹⁰ cm^?2. Remarkable changes in device characteristics were seen at a fluence of 1 × 10¹² cm^?2 for carbon, oxygen, iron and krypton irradiation. Similarly, remarkable changes were also observed in the GaN layer for irradiations with fluence of 1 × 10¹² cm^?2. The results found on devices and on the GaN layer were compared and correlated.     

High-performance C60 and picene thin film field-effect transistors with conducting polymer electrodes in bottom contact structure

C₆₀ and picene thin film field-effect transistors (FETs) in bottom contact structure have been fabricated with poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) electrodes for a realization of mechanical flexible organic FETs. The C₆₀ thin film FETs showed n-channel enhancement-type characteristics with the field-effect mobility μ value of 0.41 cm² V^?1 s^?1, while the picene thin film FET showed p-channel enhancement-type characteristics with the μ of 0.61 cm² V^?1 s^?1. The μ values recorded for C₆₀ and picene thin film FETs are comparable to those for C₆₀ and picene thin film FETs with Au electrodes.     

IGZO thin film transistors with Al2O3 gate insulators fabricated at different temperatures

Thin film transistors (TFTs) with bottom gate and staggered electrodes using atomic layer deposited Al₂O₃ as gate insulator and radio frequency sputtered In–Ga–Zn Oxide (IGZO) as channel layer are fabricated in this work. The performances of IGZO TFTs with different deposition temperature of Al₂O₃ are investigated and compared. The experiment results show that the Al₂O₃ deposition temperature play an important role in the field effect mobility, I_on/I_off ratio, sub-threshold swing and bias stability of the devices. The TFT with a 250 °C Al₂O₃ gate insulator shows the best performance; specifically, field effect mobility of 6.3 cm²/Vs, threshold voltage of 5.1 V, I_on/I_off ratio of 4×10⁷, and sub-threshold swing of 0.56 V/dec. The 250 °C Al₂O₃ insulator based device also shows a substantially smaller threshold voltage shift of 1.5 V after a 10 V gate voltage is stressed for 1 h, while the value for the 200, 300 and 350 °C Al₂O₃ insulator based devices are 2.3, 2.6, and 1.64 V, respectively.     

Dependence of annealing on stability of transparent amorphous InGaZnO thin film transistor

Bottom-gate transparent IGZO–TFT had been successfully fabricated at relatively low temperature (200 °C). The devices annealing for 4 h at 200 °C exhibit good electrical properties with saturation mobility of 8.2 cm²V^?1s^?1, subthreshold swing of 1.0 V/dec and on/off current ratio of 5×10⁶. The results revealed that the stability of TFT devices can be improved remarkably by post-annealing treatment. After applying positive gate bias stress of 20 V for 5000 s, the device annealing for 1 h shows a larger positive V_th shift of 4.7 V. However, the device annealing for 4 h exhibits a much smaller V_th shift of 0.04 V and more stable.     

Investigation of TiO2 on AlGaAs prepared by liquid phase deposition and its application

The study explored titanium dioxide (TiO₂) on aluminum gallium arsenide (AlGaAs) prepared by liquid phase deposition (LPD) at 40 °C. The leakage current density was about 8.4 × 10^?6 A/cm² at 1 MV/cm. The interface trap density (D_it) and the flat-band voltage shift (ΔV_FB) were 2.3 × 10¹² cm^?2 eV^?1 and 1.2 V, respectively. After rapid thermal annealing (RTA) in the ambient N₂ at 350 °C for 1 min, the leakage current density, D_it, and ΔV_FB were improved to 2.4 × 10^?6 A/cm² at 1 MV/cm, 7.3 × 10¹¹ cm^?2 eV^?1, and 1.0 V, respectively. Finally, the study demonstrates the application to the AlGaAs/InGaAs metal–oxide–semiconductor pseudomorphic high-electron-mobility transistor (MOS-PHEMT). The results indicate the potential of the proposed device with a LPD-TiO₂ gate oxide for power application.     

Region-dependent behavior of I–V characteristics in n-ZnO:Al/p-Si contacts

The discrepancy of rectifying characteristics in n-ZnO:Al/p-Si heterojunctions from diode to diode was demonstrated by region dependent dark I–V characteristics, where the junction is laterally cut to sequentially decrease the area. Further investigation shows that the junction (2.1×2.1 cm²) with the barrier height Φ=0.693 eV consists of one part (2.1×1.4 cm²) with Φ=0.695 eV and the other part (2.1×0.7 cm²) with Φ=0.686 eV. It is found that reverse currents saturate with different values of 3.6×10^?3, 2.5×10^?3 and 1.58×10^?3 A for the light I–V curves of the three junctions with the same areas. To explain this peculiarity, the probable reason is discussed in terms of carrier transportation through the spatially fluctuating barrier.     

Photoreactive π-conjugated star-shaped molecules for the organic field-effect transistor

A number of semiconducting organic molecules capable of wet processing exhibit high carrier mobility and current modulation. In this work, we synthesized photopatternable π-conjugated star-shaped molecules and characterized their physical properties. The solubility of the synthesized molecules is very good for solution processing. The synthesized organic semiconducting multi-branched molecules are capable of photopatterning by virtue of photopolymerization of the reactive pentadienyl end groups. The transistor devices using these molecules provided a field-effect mobility of 1.3(±0.2) × 10^?3–3.7(±0.5) × 10^?3 cm² V^?1 s^?1 as well as a high current on/off ratio (I_on/off > 10³) and a low threshold voltage. In the case of the photoreactive star-shaped conjugated molecule HP2P, it was found that field-effect mobility was maintained even after the photocrosslinking process. This result can be used in the design of photopatternable semiconductor molecules for thin-film transistor electronic applications.     

High performance inkjet-printed C60 fullerene thin-film transistors: Toward a low-cost and reproducible solution process

We have demonstrated high performance inkjet-printed n-channel thin-film transistors (TFTs) using C₆₀ fullerene as a channel material. Highly uniform amorphous C₆₀ thin-film patterns were fabricated on a solution-wettable polymer gate dielectric layer by inkjet-printing and vacuum drying process. Fabricated C₆₀ TFTs shows great reproducibility and high performance; field-effect mobilities of 2.2–2.4 cm² V^?1 s^?1, threshold voltages of 0.4–0.6 V, subthreshold slopes of 0.11–0.16 V dec^?1 and current on/off ratio of 10⁷–10⁸ in a driving voltage of 5 V. This is due to the efficient annealing process that extracting the solvent residue and the formation of low trap-density gate dielectric surface.     

Experimental study for high effective mobility with directly deposited HfO2/La2O3 MOSFET

We experimentally examine the effective mobility in nMOSFETs with La₂O₃ gate dielectrics without SiO_x-based interfacial layer. The reduced mobility is mainly caused by fixed charges in High-k gate dielectrics and the contribution of the interface state density is approximately 30% at N_s = 5 × 10¹¹ cm^?2 in the low 10¹¹ cm^?2 eV^?1 order. It is considered that one of the effective methods for improving mobility is to utilize La-silicate layer formed by high temperature annealing. However, there essentially exists trade-off relationship between high temperature annealing and small EOT.     

Benzopyrazine-fused tetracene derivatives: Thin-film formation at the crystalline mesophase for solution-processed hole transporting devices

Benzopyrazine-fused tetracene (TBPy) and its disulfide (TBPyS) bearing alkoxy groups (OCH₃, OC₈H₁₇) were designed and synthesized to obtain π-expanded tetracene derivatives. These derivatives are featured with long-wavelength light absorption property (λ_onset: up to 820 nm), photooxidative stability (half-lives (τ_1/2): 11 times longer than tetracene), and solubility for solution process. The methoxy compounds (TBPy-C1 and TBPyS-C1) were used for single-crystal X-ray crystallographic analysis and single-crystal organic field-effect transistor (OFET) devices showing relationship between packing structures and hole mobilities. The octyloxy compounds (TBPy-C8 and TBPyS-C8) were investigated on solution-processed thin-film formation and hole transport property in thin-film OFET devices. Crystalline mesophase of TBPy-C8 and TBPyS-C8 was characterized by differential scanning calorimetry analysis showing endothermic peaks at 98 and 198 °C on its second heating process and exothermic peaks at 177 and 76 °C on its second cooling process for TBPyS-C8, and played crucial roles in thin-films formation. Hole mobility of 1.7 × 10^?2 cm²/V s (with V_th = ?30 V and I_ON/I_OFF = 10⁴) was obtained for the thin-film OFET device of TBPyS-C8.     

Effect of doping of cesium carbonate on electron transport in Tris(8-hydroxyquinolinato) aluminum

Electron transport studies in Tris(8-hydroxyquinolinato) aluminum (Alq₃) is hindered due to lack of efficient electron injecting electrode. We demonstrate that an electron injection layer of Cs₂CO₃ forms ohmic contact with Alq₃, which enables the observation of SCLC. This allows us to directly determine the electron mobility in Alq₃, which was found to be 1 × 10^?9 m²/V s at room temperature. Doping of Cs₂CO₃ leads to increase in conductivity as well as mobility. Mobility has increased to 1 × 10^?7 m²/V s for 33% doping of Cs₂CO₃.     

Magnetron-sputtered high performance Y-doped ZnO thin film transistors fabricated at room temperature

In this report, sputtered-grown undoped ZnO and Y-doped ZnO (ZnO:Y) thin film transistors (TFTs) are presented. Both undoped ZnO and ZnO:Y thin films exhibited highly preferred c-axis oriented (002) diffraction peaks. The ZnO:Y thin film crystallinity was improved with an increase of (002) peak intensity and grain size. The electrical properties of ZnO:Y TFTs were significantly enhanced relative to undoped ZnO TFTs. ZnO:Y TFTs exhibited excellent performance with high mobility of 38.79 cm² V⁻¹ s⁻¹, small subthreshold swing of 0.15 V/decade, and high I_on/I_off current ratio of the order of 8.17 × 10⁷. The O_1s X-ray photoelectron spectra (XPS) showed oxygen vacancy-related defects present in the ZnO:Y TFTs, which contributed to enhancing the mobility of the TFTs.     

Determination of contact parameters of Ni/n-GaP Schottky contacts

The electrical analysis of Ni/n-GaP structure has been investigated by means of current–voltage (I–V), capacitance–voltage (C–V) and capacitance–frequency (C–f) measurements in the temperature range of 120–320 K in dark conditions. The forward bias I–V characteristics have been analyzed on the basis of standard thermionic emission (TE) theory and the characteristic parameters of the Schottky contacts (SCs) such as Schottky barrier height (SBH), ideality factor (n) and series resistance (R_s) have been determined from the I–V measurements. The experimental values of SBH and n for the device ranged from 1.01 eV and 1.27 (at 320 K) to 0.38 eV and 5.93 (at 120 K) for Ni/n-GaP diode, respectively. The interface states in the semiconductor bandgap and their relaxation time have been determined from the C–f characteristics. The interface state density N_ss has ranged from 2.08 × 10¹⁵ (eV^?1 m^?2) at 120 K to 2.7 × 10¹⁵ (eV^?1 m^?2) at 320 K. C_ss has increased with increasing temperature. The relaxation time has ranged from 4.7 × 10^?7 s at 120 K to 5.15 × 10^?7 s at 320 K.     

Hole mobilities of thermally polymerized triaryldiamine derivatives and their application as hole-transport materials in organic light-emitting diodes (OLEDs)

This paper describes the synthesis of three triaryldiamine derivatives presenting two thermally polymerizable trifluorovinyl ether groups that can be polymerized through thermal curing to form perfluorocyclobutyl (PFCB) polymers. These PFCB polymers, studied using time-of-flight techniques for the first time, exhibited remarkable non-dispersive hole-transport properties, with values of μ_h of ca. 10^?4 cm² V^?1 s^?1. When we employed these thermally polymerized polymers as hole-transport layers (HTLs) in electroluminescence devices containing tris(8-hydroxyquinolate) aluminum (Alq₃) as the emission layer, we obtained high current densities (ca. 3400 mA cm^?2), impressive brightnesses (5 × 10⁴ cd m^?2), and high external quantum efficiencies (EQEs = 1.43%). These devices exhibited the same turn-on voltage, but higher EQEs, relative to those incorporating the vacuum-processed model compound N,N′-di(1-naphthyl)-N,N′-diphenylbenzidine (α-NPD) (EQE = 1.37%) as the HTL under the same device structure.     

Determination of the laterally homogeneous barrier height of palladium Schottky barrier diodes on n-Ge (1 1 1)

We have studied the experimental linear relationship between barrier heights and ideality factors for palladium (Pd) on bulk-grown (1 1 1) Sb-doped n-type germanium (Ge) metal-semiconductor structures with a doping density of about 2.5×10¹⁵ cm^?3. The Pd Schottky contacts were fabricated by vacuum resistive evaporation. The electrical analysis of the contacts was investigated by means of current–voltage (I–V) and capacitance–voltage (C–V) measurements at a temperature of 296 K. The effective barrier heights from I–V characteristics varied from 0.492 to 0.550 eV, the ideality factor n varied from 1.140 to 1.950, and from reverse bias capacitance–voltage (C^?2–V) characteristics the barrier height varied from 0.427 to 0.509 eV. The lateral homogenous barrier height value of 0.558 eV for the contacts was obtained from the linear relationship between experimental barrier heights and ideality factors. Furthermore the experimental barrier height distribution obtained from I–V and (C^?2?V) characteristics were fitted by Gaussian distribution function, and their mean values were found to be 0.529 and 0.463 eV, respectively.     

Organic field-effect transistor and its photoresponse using a benzo[1,2-b:4,5-b′]difuran-based donor–acceptor conjugated polymer

Organic field-effect transistors (OFETs) were fabricated through a solution process with a donor–acceptor (D–A) conjugated polymer poly{4,8-bis(2′-ethylhexylthiophene)benzo [1,2-b;3,4-b′]difuran-alt-5,5-(4′,7′-di-2-thienyl-5′,6′-dioctyloxy-2′,1′,3′-benzothiadiazole)} (PBDFTDTBT) as the active layer, which is a highly efficient D–A conjugated polymer as a donor in polymer solar cells with a power conversion efficiency (PCE) over 6.0%. The OFET devices showed a hole mobility of 0.05 cm²/Vs and an on/off ratio of 4.6 × 10⁵. Those are one of the best performance parameters for OFETs based on D–A conjugated polymers including benzo[1,2-b:4,5-b′]dithiophene (BDT) or benzo[1,2-b:4,5-b′]difuran (BDF) unit. The photoresponse of OFETs was investigated by modulating light with various intensities. The devices produced a photosensitivity (I_light/I_dark) of 1.2 × 10⁵ and a photoresponsivity of 360 mA W⁻¹ under white light illumination. The drain current in saturation region increases gradually with increasing illumination intensity. The threshold voltage exhibited a positive shift from −15.6 V in darkness to 27.8 V under illumination, which can be attributed to the well-known photovoltaic effect resulting from the transport of photogenerated holes and trapping of photogenerated electrons near the source electrode in organic phototransistors. Meanwhile, the devices showed good stability and with no obvious degeneration for 3 months in air. The study suggests that D–A conjugated polymers including BDF unit can be potentially applied in OFETs and organic phototransistors in addition to highly efficient polymer solar cells.     

Multihydroxylated aryl amine as a novel alcohol-processable hole-transport molecular glass exhibiting remarkable resistance to weakly polar solvents

Multihydroxylation of a small-molecule aryl amine leads to a contrasting solubility in polar and weakly polar solvents. The resulting compound shows an intrinsic amorphous morphology with a high T_g of 190 °C and is capable of affording uniform smooth and transparent films, spin-cast from 2-propanol. The fitting of the space-charge-limited current characteristics reveals a hole mobility of ～4.6 × 10^?6 cm² V^?1 s^?1 at low-voltages. Incorporating this new compound as a hole-transport layer into conventional bottom-anode organic light-emitting diodes that consisted of a solution-processed emitter provides promising performance.