Effect of the work function of gate electrode on hysteresis characteristics of organic thin-film transistors with Ta2O5/polymer as gate insulator

Organic thin-film transistors (OTFTs) using high dielectric constant material tantalum pentoxide (Ta₂O₅) and benzocyclobutenone (BCBO) derivatives as double-layer insulator were fabricated. Three metals with different work function, including Al (4.3 eV), Cr (4.5 eV) and Au (5.1 eV), were employed as gate electrodes to study the correlation between work function of gate metals and hysteresis characteristics of OTFTs. The devices with low work function metal Al or Cr as gate electrode exhibited high hysteresis (about 2.5 V threshold voltage shift). However, low hysteresis (about 0.7 V threshold voltage shift) OTFTs were attained based on high work function metal Au as gate electrode. The hysteresis characteristics were studied by the repetitive gate voltage sweep of OTFTs, and capacitance–voltage (C–V) and trap loss-voltage (G_p/ω?V) measurements of metal–insulator–semiconductor (MIS) devices. It is proved that the hysteresis characteristics of OTFTs are relative to the electron injection from gate metal to Ta₂O₅ insulator. The electron barrier height between gate metal and Ta₂O₅ is enhanced by using Au as gate electrode, and then the electron injection from gate metal to Ta₂O₅ is reduced. Finally, low hysteresis OTFTs were fabricated using Au as gate electrode.     

Photocurable propyl-cinnamate-functionalized polyhedral oligomeric silsesquioxane as a gate dielectric for organic thin film transistors

A polyhedral oligomeric silsesquioxane (POSS)-based insulating material with photocurable propyl-cinnamate groups (POSS-CYNNAM) was designed and synthesized through simple single step reaction for use as a gate dielectric in organic thin-film transistors (OTFT). POSS-CYNNAM was soluble in common organic solvents and formed a smooth thin film after spin-casting. A thin film of POSS-CYNNAM was cross-linked and completely solidified under UV irradiation without the use of additives such as photoacid generators or photoradical initiators. ITO/insulator/Au devices were fabricated and characterized to measure the dielectric properties of POSS-CYNNAM thin films, such as leakage current and capacitance. A pentacene-based OTFT using the synthesized insulator as the gate dielectric layer was fabricated on the transparent indium tin oxide (ITO) electrode, and its performance was compared to OTFTs using thermally cross-linked poly(vinyl phenol) (PVP) as the insulator. The fabricated POSS-CYNNAM OTFT showed a comparable performance to devices based on the PVP insulator with 0.1 cm²/Vs of the field effect mobility and 4.2 × 10⁵ of an on/off ratio.     

Organic thin-film transistors with bilayer of rubbed and evaporated hydrocarbon-based acene as active layer

We have investigated organic thin-film transistors (OTFTs) with a bilayer of rubbed and evaporated hydrocarbon-based acene 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT) as an active layer. Using a rubbing process after spin-coating the C8-BTBT, crystallinity of the C8-BTBT thin film was improved and resultant superior OTFT characteristics were realized. We obtained a field-effect mobility of 1.6 cm²/Vs, a threshold voltage of −8.2 V, an on-off ratio of 10⁶, and a subthreshold swing of 55 mV/decade.     

Organic thin film transistors with double insulator layers

We have investigated a double-layer structured gate dielectric for the organic thin films transistor (OTFT) with the purpose of improving the performance of the SiO₂ gate insulator. A 50 nm PMMA layer was coated on top of the SiO₂ gate insulator as organic insulator layer. The results demonstrated that using inorganic/organic compound insulator as the gate dielectric layers is an effective method to fabricate OTFTs with improved electric characteristics and decreased leakage current. Electrical parameters such as carrier mobility and on/off ratio by field effect measurement have been calculated. OTFT based on highly doped Si substrate with a field-effect mobility of 0.004 cm²/V s and on/off ratio of 10⁴ have been obtained.     

High-performance thin-film transistor with 6,13-bis(triisopropylsilylethynyl) pentacene by inkjet printing

We have studied the performance improvement of organic thin-film transistor (OTFT) with a solution based TIPS pentacene (6,13-bis(triisopropylsilylethynyl)pentacene) by inkjet printing. The TIPS pentacene with 1.0 wt.% solution in 1,2-dichlorobenzene was used for printing of an active layer of OTFT. The OTFT printed at room temperature shows a shoulder-like behavior but it disappears for the OTFT printed at the substrate temperature of 60 °C. The OTFT on plastic exhibited an on/off current ratio of ∼10⁷, a threshold voltage of −2.0 V, a gate voltage swing of 0.6 V/decade and a field-effect mobility of 0.24 cm²/Vs in the saturation region.     

Pentacene organic thin-film transistors with solution-based gelatin dielectric

Gelatin is a natural protein in the field of food, pharmaceutical and tissue engineering, which works very well as the gate dielectric for pentacene organic thin-film transistors (OTFTs). An aqueous solution process has been applied to form a gelatin thin film on poly(ethylene terephthalate) (PET) or glass by spin-coating and subsequent casting. The device performance of pentacene OTFTs depend on the bloom number (molecular weight) of gelatin. The pentacene OTFT with 300 bloom gelatin as the gate dielectric in air ambient exhibits the best performance with an average field-effect mobility (μ_FE) value of ca. 16 cm² V^?1 s^?1 in the saturation regime and a low threshold voltage of ?1 V. The high performance of the pentacene OTFT in air ambient is attributed to the water resided in gelatin. The crystal quality of pentacene is not the key factor for the high performance.     

Fabrication of the flexible pentacene thin-film transistors on 304 and 430 stainless steel (SS) substrate

Flexible organic thin-film transistors (OTFT) were fabricated on 304 and 430 stainless steel (SS) substrate with aluminum oxide as a gate insulator and pentacene as an organic semiconductor. Chemical mechanical polishing (CMP) process was used to study the effect of the SS roughens on the dielectric properties of the gate insulator and OTFT characteristics. The surface roughness was decreased from 33.8 nm for 304 SS and 19.5 nm for 430 SS down to ～2.5 nm. The leakage current of the metal–insulator–metal (MIM) structure (Au/Al₂O₃/SS) was reduced with polishing. Mobility and on/off ratio of pentacene TFT with bare SS showed a wide range of values between 0.005 and 0.36 cm²/Vs and between 10³ and 10⁵ depending on the location in the substrate. Pentacene TFTs on polished SS showed an improved performance with a mobility of 0.24–0.42 cm²/Vs regardless of the location in the substrate and on/off ratio of ～10⁵. With self assembled monolayer formation of octadecyltrichlorosilane (OTS) on insulator surface, mobility and on/off ratio of pentacene TFT on polished SS was improved up to 0.85cm²/Vs and ～10⁶. I–V characteristics of pentacene TFT with OTS treated Al₂O₃/304 SS was also obtained in the bent state with a bending diameter (D) of 24, 45 or 70 mm and it was confirmed that the device performed well both in the linear regime and the saturation regime.     

Hybridization of a low-temperature processable polyimide gate insulator for high performance pentacene thin-film transistors

We have synthesized a novel fully soluble and low-temperature processable polyimide gate insulator (KSPI) through the one-step condensation polymerization of the monomers 5-(2,5-dioxytetrahydrofuryl)-3-methyl-3-cyclohexene-1,2-dicarboxylic anhydride and 4,4-diaminodiphenylmethane. Fully imidized KSPI was found to be completely soluble in organic solvents such as N-methyl-2-pyrrolidone (NMP), dimethylacetamide (DMAc), γ-butyrolactone, dimethylsulfoxide (DMSO), and 2-butoxyethanol. Thin films of KSPI can be fabricated at only 150 °C and a pentacene OTFT with KSPI as a gate dielectric was found to exhibit a field effect mobility of 0.22 cm²/V s. To obtain a high performance organic thin-film transistor (OTFT), the KSPI surface was modified in our new technique by hybridization with a non-polar side chain containing a polyimide insulator (PI). The carrier mobility of a pentacene OTFT with a hybridized polyimide gate insulator (BPI-3) was found to be 0.92 cm²/V s. Our new low-temperature processable polyimides show promise as gate dielectrics for OTFTs.     

Soluble pentacene thin-film transistor using a high solvent and heat resistive polymeric dielectric with low-temperature processability and its long-term stability

Solution processable organic thin-film transistors (OTFTs) were fabricated using 6,13-bis(triisopropyl-silylethynyl) pentacene (TIPS-pentacene) and low-temperature processable polyimide gate dielectric. The TIPS-pentacene OTFT with the dielectric was found to have a field-effect mobility of 0.15 cm²/Vs, which is comparable to that of OTFT with an inorganic dielectric. The OTFTs with the polyimide dielectric did not show any significant performance degradation as time passed. A field-effect mobility of the OTFTs in 60 days was found to be almost identical to that of pristine OTFT. The combination of TIPS-pentacene and our polyimide gate dielectric can be one of the potential candidates for the fabrication of stable OTFTs for large-area flexible electronics.     

IGZO thin film transistors with Al2O3 gate insulators fabricated at different temperatures

Thin film transistors (TFTs) with bottom gate and staggered electrodes using atomic layer deposited Al₂O₃ as gate insulator and radio frequency sputtered In–Ga–Zn Oxide (IGZO) as channel layer are fabricated in this work. The performances of IGZO TFTs with different deposition temperature of Al₂O₃ are investigated and compared. The experiment results show that the Al₂O₃ deposition temperature play an important role in the field effect mobility, I_on/I_off ratio, sub-threshold swing and bias stability of the devices. The TFT with a 250 °C Al₂O₃ gate insulator shows the best performance; specifically, field effect mobility of 6.3 cm²/Vs, threshold voltage of 5.1 V, I_on/I_off ratio of 4×10⁷, and sub-threshold swing of 0.56 V/dec. The 250 °C Al₂O₃ insulator based device also shows a substantially smaller threshold voltage shift of 1.5 V after a 10 V gate voltage is stressed for 1 h, while the value for the 200, 300 and 350 °C Al₂O₃ insulator based devices are 2.3, 2.6, and 1.64 V, respectively.     

Channel width effect for organic thin film transistors using TIPS-pentacene employed as a dopant of poly-triarylamine

The effects of the physical channel width on the characteristics of organic thin film transistors (OTFTs), made with 6,13-bis(triisopropyl-silylethynyl)-pentacene (TIPS-pentacene) embedded into poly-triarylamine (PTAA, hole conductor within an active channel), have been examined in this paper. The devices are estimated by measuring the drain-source current (I_DS) for different contact metals such as Au and Ag, at fixed gate and drain voltages. The results show that the threshold voltage (V_T) and I_DS increase with increasing channel width. Furthermore, it has been observed that the field effect mobility is dependent on V_T, which is influenced by the channel width. The OTFTs, produced using Au and Ag contacts, exhibited the highest values of mobility in the saturation regime, namely 5.44 × 10^?2 and 1.33 × 10^?2 cm²/Vs, respectively.     

Improving the performance of organic thin-film transistor with a doped interlayer

Top contact organic thin-film transistors (TC OTFTs) based on pentacene are fabricated. For improving the contact characteristics between the organic semiconductor thin-film and gold electrodes, we doped the starburst molecular 4,4′,4″-tris{N,(3-methylpheny)-N-phenylamino}-triphenylamine) (m-MTDATA), which is an excellent hole injection material for the organic light-emitting devices (OLEDs), into the interlayer contact with the electrodes. Compared with conventional TC OTFT, the performances of the organic transistor with the doped interlayer are improved. The field-effect mobility increases from 0.16 to 0.51 cm²/V s, and threshold voltage downshifts from –11 to –2.8 V for the linear region. The on/off current ratio is more than 10⁴ when the gate voltage varies from 0 to –20 V. We ascribe the improvements to the doped interlayer for which the contact resistance is reduced and the hole injection is enhanced.     

Effect of active layer thickness on environmental stability of printed thin-film transistor

We have studied the effect of active layer thickness on the performance and environmental stability of the 6,13-bis(triisopropylsilylethynyl) pentacene (TIPS pentacene) thin-film transistor. The organic thin-film transistors (OTFTs) were fabricated by inkjet printing using a solution based TIPS pentacene. To get thick organic semiconductor, the surface of gate insulator was treated with n-octyltrichlorosilane (OTS-C₈) before jetting. The on-currents of the OTFT with ～1 μm active layer decreases a little in air, but the OTFT with 0.05 μm TIPS pentacene shows a significant degradation in drain currents.     

Improving the performance of the organic thin-film transistors with thin insulating lithium fluoride buffer layer

The pentacene-based organic thin-film transistors (OTFTs) with a thin insulating lithium fluoride (LiF) buffer layer between the pentacene and source/drain electrodes were fabricated. Compared with conventional OTFTs, the introduction of the buffer layer (1 nm) leads to field-effect mobility increases from 0.16 to 0.5 cm²/Vs, and threshold voltage downshifts from −19 to −8 V for the linear region. The on/off current ratio is improved to a level of 10⁵ for the off-state current decreasing. These improvements are attributed to (i) tunneling injection through the LiF layer and (ii) interface dipole energy barrier decreasing and contact resistance reduction between pentacene and Au. The results demonstrate that it is an effective method to improve the device characteristics by using a buffer layer.     

Stable organic thin-film transistor in a pixel for plastic electronics

We have studied the fabrication of stable organic thin-film transistor (OTFT) for plastic electronics using hybrid multi-layer (HML) of parylene/Au/photoacryl/IZO (indium zinc oxide) on organic semiconductor. The HML-passivated OTFTs exhibited the field-effect mobility (μ_fe) of 0.2–0.3 cm²/V s with an on/off current ratio of 10⁷ after annealing at 180 °C. The changes in on-, off- and subthreshold-currents of the HML-passivated OTFT were negligibly small during the storage of 781 h. Moreover, the hysteresis in transfer characteristics was negligible even after exposure of the OTFT to air for 781 h. These results indicate that HML-passivation is suitable for stable OTFT array for plastic electronics.     

Novel organic inverters with dual-gate pentacene thin-film transistor

We report on the fabrication and characterization of dual-gate pentacene organic thin-film transistors (OTFTs) with plasma-enhanced atomic-layer-deposited (PEALD) 150 nm thick Al₂O₃ as a bottom-gate dielectric and PEALD 200 nm thick Al₂O₃ as a top-gate dielectric. The V_th of dual-gate OTFT has changed systematically with the application of voltage bias to top-gate electrode. When voltage bias from −10 V to 10 V is applied to top gate, V_th changes from 1.95 V to −9.8 V. Two novel types of the zero drive load logic inverter with dual-gate structure have been proposed and fabricated using PEALD Al₂O₃ gate dielectrics. Because the variation of V_th due to chemical degradation and the spatial variation of V_th are inherent in OTFTs, the compensation technology by dual-gate structure can be essential to OTFT applications.     

Effect of gate insulator thickness on device performance of InGaZnO thin-film transistors

Top-contact thin-film transistors (TFTs) are fabricated in this work using atomic layer deposition (ALD) Al₂O₃ as the gate insulator and radio frequency sputtering InGaZnO (IGZO) as the channel layer so as to investigate the effect of Al₂O₃ thickness on the performance of IGZO-TFTs. The results show that TFT with 100-nm-thick Al₂O₃ (100 nm-Al₂O₃-TFT) exhibits the best electrical performance; specifically, field-effect mobility of 5 cm²/Vs, threshold voltage of 0.95 V, I_on/I_off ratio of 1.1×10⁷ and sub-threshold swing of 0.3 V/dec. The 100 nm-Al₂O₃-TFT also shows a substantially smaller threshold voltage shift of 1.1 V after a 10 V gate voltage is applied for 1 h, while the values for TFTs with an Al₂O₃ thickness of 220 and 280 nm are 1.84 and 2 V, respectively. The best performance of 100 nm-Al₂O₃-TFT can be attributed to the larger capacitance and the smaller amount of total trap centers possessed by a thinner insulator compared to the thicker ones.     

Design and realization of a flexible QQVGA AMOLED display with organic TFTs

We present a QQVGA top emitting monochrome AMOLED display with 85dpi resolution using an organic TFT backplane on low temperature PEN-foil. The backplane process flow is based on a 7 layer photolithography process that yields a final mobility of the OTFT of ～0.4 cm²/Vs. The aperture ratio of the top-emitting OLEDs is over 75%. For operation at 10 V supply voltage (V_DD), the brightness of the display using red and green OLEDs exceeds 200 cd/m².     

Photo-patternable polyimide gate insulator with fluorine groups for improving performance of 2,7-didecyl[1]benzothieno[3,2-b][1]benzothiopene (C10-BTBT) thin-film transistors

Surface properties of gate insulators strongly affect the device performance of organic thin-film transistors (OTFTs). To improve the performance of OTFTs, we have developed photo-sensitive polyimide gate insulator with fluorine groups. The polyimide gate insulator film could be easily patterned by selective UV exposure without any photoinitiator. The polyimide gate insulator film, fabricated at 130 °C, has a dielectric constant of 2.8 at 10 kHz, and leakage current density of <1.6 × 10^?10 A/cm² while biased from 0 to 90 V. To investigate the potential of the polyimide with fluorine groups as a gate insulator, we fabricated C₁₀-BTBT TFTs. The field-effect mobility and the on/off current ratio of the TFTs were measured to be 0.76 ± 0.09 cm²/V s and >10⁶, respectively.     

Bottom gate organic thin-film transistors fabricated by ultraviolet transfer embossing with improved device performance

Ultraviolet transfer embossing is optimized to fabricate bottom gate organic thin-film transistors (OTFTs) on flexible plastic substrates, achieving significant improved device performance (μ = 0.01–0.02cm²/Vs; on/off ratio = 10⁴) compared with the top gate OTFTs made previously by the same method (μ = 0.001–0.002 cm²/Vs; on/off ratio = 10²). The performance improvement can be ascribed to the reduced roughness of the dielectric-semiconductor interface (R_rms = 0.852 nm) and thermally cross-linked PVP dielectric which leads to reduced gate leakage current and transistor off current in the bottom-gated configuration. This technique brings an alternative great opportunity to the high-volume production of economic printable large-area OTFT-based flexible electronics and sensors.