Corrosion of copper and silver plates by volcanic gases

Corrosion products that had been formed on copper and silver plates exposed in Miyake Island, where suffered a volcanic eruption in 2000, were analyzed by X-ray techniques to get better understanding of copper and silver corrosion in harsh environment. The exposure experiment was carried out from September 2004 to April 2005. Many kinds of patina were found on copper such as cuprite (Cu₂O), posnjakite (Cu₄SO₄(OH)₆ · H₂O), brochantite (Cu₄SO₄(OH)₆), antlerite (Cu₃SO₄(OH)₄), and geerite (Cu₈S₅). For silver, silver chloride (AgCl) and silver sulfide (Ag₂S) were formed. Although the volcanic activity had greatly subsided, the atmospheric corrosion of copper and silver plates exposed on Miyake Island was mainly affected by volcanic gases, wet-dry cycles in the environment, and sea-salt aerosols.     

Differences between corrosion products formed on copper exposed in Tokyo in summer and winter

We analyzed the copper corrosion products that formed during a month in summer and a month in winter at three sites in Tokyo using several analytical techniques. The X-ray diffraction patterns revealed that cuprite Cu₂O and posnjakite Cu₄SO₄(OH)₆·H₂O formed on copper exposed in summer. By contrast, only cuprite was found in winter exposed copper. The X-ray fluorescence results indicated that the amounts of sulfur and chlorine on the copper plates exposed in summer were much greater than those in winter. This could be explained by the change in particulate sulfate and sea salt concentrations. Depth profiling analysis by Auger electron spectroscopy revealed that the oxide layer formed in summer was thicker than that in winter. This difference in oxide layer thickness could have been due to the differences in temperature, relative humidity, and the amount of sulfur and chlorine on the copper plate.     

Copper patinas: an investigation by Auger electron spectroscopy

Auger electron spectroscopy in conjunction with Ar⁺ sputtering has been used to investigate four samples of copper that have been patinated by exposure to the atmosphere for periods ranging from 1 to 100 years. The elemental depth profiles were qualitatively similar for all samples. The patinas were covered with a thin layer of carbon containing species and consisted primarily of copper, sulfur, chlorine, and oxygen. The sulfur is present primarily near the surface of the patina and the chlorine is distributed throughout the patina. In two samples, 44 and 100 years old, significant amounts of chlorine were found in the portion of the patina nearest the bulk copper. A simple mass balance shows that the surface of the patina (beneath the carbon containing layer) is composed primarily of the mineral brochantite, Cu₄(SO₄)(OH)₆, as expected thermodynamically. A thermodynamic analysis also shows that atacamite, Cu₂Cl(OH)₃, the principal chlorine containing mineral found in the patinas, can be stable with respect to cuprite, Cu₂O, particularly in the immediate vicinity of unoxidized copper.     

Morphological study of 16-year patinas formed on copper in a wide range of atmospheric exposures

Much information is available on the atmospheric corrosion of copper and patina formation mechanisms in the short, mid and even long term. However, studies of the structure and morphology of patina layers are less abundant and mostly deal with patinas formed in the atmosphere over a small number of years. The present study concentrates on the structure and morphology of corrosion product films formed on copper after long-term atmospheric exposure (13-16 years) in five Spanish atmospheres of different types: rural, urban, industrial and marine (mild and severe). Characterisation has been performed by X-ray diffraction (XRD) and scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS). Long-term copper corrosion is higher in industrial and marine atmospheres and lower in rural and urban atmospheres. In all cases a decrease in the corrosion rate with exposure time is observed. The formation of antlerite [Cu₃SO₄(OH)₄] is seen in more acidic conditions and in specimen areas subject to a high time of wetness. The presence of nantokite (CuCl), which is not generally mentioned in field studies, has been detected under the cuprite layer very close to the base copper.     

The characterization of patina components by X-ray diffraction and evolved gas analysis

Fourteen patinated copper specimens, seven each from the Statue of Liberty, New York Habor and from roofs at AT&T Bell Laboratories in Murray Hill, NJ, ranged in atmospheric exposure from 1 to 100 years. X-ray diffraction showed the presence of cuprite, Cu₂O, and brochantite, Cu₄(SO₄)(OH)₆, in all specimens and antlerite, Cu₃(SO₄)(OH)₄ (up to 0.7 times brochantite), atacamite, Cu₂Cl(OH)₃ (up to 1.6 times brochantite), and/or posnjakite, Cu₄(SO₄)(OH)₆ · 2H₂O (up to 5.2 times brochantite) in some. Posnjakite has been previously reported as a patina component only once during short term exposures in Eurasia. It appears to be an early corrosion product which subsequently converts to brochantite. Mass spectrographic examination of gases emitted from heated patinas provides further information on patina composition, in particular on the presence of both carbonate and oxalate in widely varying ratios.     

Effects of blending on surface characteristics of copper corrosion products in drinking water distribution systems

Copper scales formed over 6-months during exposure to ground, surface and saline waters were characterized by EDS, XRD and XPS. Scale color and hardness were light red-brown-black/hard for high alkalinity and blue-green/soft for high SO₄ or Cl waters. Cl was present in surface or saline copper scales. The Cu/Cu₂O ratio decreased with time indicating an e transfer copper corrosion mechanism. Cu₂O, CuO, and Cu(OH)₂ dominated the top 0.5-1 A° scale indicating continuous corrosion. Cu₂O oxidation to CuO increased with alkalinity, and depended on time and pH. Total copper release was predicted using a Cu(OH)₂ model.     

Influence of the corrosion products of copper on its atmospheric corrosion kinetics in tropical climate

In the present paper, the identification of the corrosion product phases formed on copper under different atmospheres of Cuban tropical climate is reported. Cuprite (Cu₂O), paratacamite (Cu₂Cl(OH)₃), posnjakite (Cu₄SO₄(OH)₆ · 2H₂O) and brochantite (Cu₄SO₄(OH)₆) were the main phases identified by X-ray diffraction (XRD) analysis and Fourier transform infrared spectroscopy (FTIR).Copper corrosion products are known to have a protective effect against corrosion. However, a different behaviour was obtained under sheltered coastal conditions. This can be due to the corrosion products morphology and degree of crystallisation, rather than their phase composition. A higher time of wetness and the accumulation of pollutants not washed away from the metal surface can also play an important role.     

Corrosion of copper in seawater and its aerosols in a tropical island

A complete characterization of copper corrosion behavior has been carried out under permanent immersion, water line, splash zone and at the atmosphere (near and far from the sea) at the tropical Cuban archipelago. No significant differences have been determined for corrosion of copper under complete immersion for test sites representative of Cuban archipelago. The maximum corrosion rate was observed on the line of water, related to the partial removing of the corrosion products layer due to water movement (waves) and a higher availability of oxygen. Patina composition was characterized using XRD, IR, EDS and SEM techniques. Paratacamite (Cu₂(OH)₃Cl) was the main component of the patina formed under complete immersion, on the line of water and in the splash zone. In poorly polluted atmospheric marine environments also atacamite (another structural modification of Cu₂(OH)₃Cl) was found. When environmental SO₂ reaches a competitive level with the chloride aerosol the patina formed is a complex mixture of basic cupric chlorides (paratacamite and atacamite) and basic cupric sulfates, antlerite (Cu₃(SO₄)(OH)₄) and brochantite (Cu₄(SO₄)(OH)₆). Brochantite and basic cupric chlorides are detected at inland rural sites. The patina morphology reveals details about the local environment in which it is formed and shed light on its more or less protective role for the metal. The relatively large corrosion rate under complete immersion and on the line of water is related to the formation of a patina with poor adherence to the metal surface and to a porous layer of cuprite formed by relatively large octahedral crystals.     

X-ray diffraction phase analysis of crystalline copper corrosion products after treatment in different chloride solutions

The corrosion products Cu₂(OH)₃Cl, Cu₂O, and CuCl₂ were identified on the surface of copper plates after their four days treating in three different sodium chloride, sodium/magnesium, and sodium/calcium chloride solutions using X-ray diffraction powder analysis. However, the quantitative proportions of individual corrosion products differ and depend on the type of chloride solution used. Treating of copper plates only in the sodium chloride solution produced the mixture of corrosion products where Cu₂O is prevailing over the Cu₂(OH)₃Cl and CuCl₂ was not identified. The sample developed after treating of the cooper surface in the sodium/magnesium chloride solution contains Cu₂(OH)₃Cl and CuCl₂ prevailing over the Cu₂O, while the sample developed after treatment of copper in sodium/calcium chloride solution contains Cu₂(OH)₃Cl prevailing over CuCl₂ and Cu₂O was not identified.     

Corrosion behaviour of die-cast AZ91D magnesium alloy in aqueous sulphate solutions

The corrosion behaviour of die-cast AZ91D magnesium alloys in sulphate solutions was investigated by SEM, FTIR and polarization measurements. For immersion times less than 48 h, no pitting corrosion occurred and only generalized corrosion was apparent. According to the polarization curves, the corrosion rate order of the die-cast AZ91D Mg alloy in three aqueous solutions was: NaCl > MgSO₄ > Na₂SO₄. The main corrosion products were Mg(OH)₂ and MgAl₂(SO₄)₄·22H₂O in the sulphate solutions and the product film was compact. Precipitation of MgAl₂(SO₄)₄·22H₂O required a threshold immersion time.     

The effect of synthetic zinc corrosion products on corrosion of electrogalvanized steel. II. Zinc reactivity and galvanic coupling zinc/steel in presence of zinc corrosion products

The reactivity of zinc under synthetic zinc patinas and the galvanic coupling in steel/patina/Zn are studied. Zn₅(OH)₆(CO₃)₂ and Na₂Zn₃(CO₃)₄⋅3H₂O inhibit zinc anodic dissolution in NaCl, while Zn₅(OH)₈Cl₂ H₂O and Zn₄(OH)₆SO₄ nH₂O do not. The galvanic current in steel/patina/NaCl/Zn is smaller as compared to steel/NaCl/Zn. The inhibiting effect decreases with time for Na₂Zn₃(CO₃)₄⋅3H₂O or Zn₄(OH)₆SO₄ nH₂O due to the transformation into Zn(OH)₂. In NaHCO₃, the polarity between zinc and steel can reverse. The effect of confinement on the cathodic current is stronger than the initial effect of patina which is explained by the instability of the patinas under rapid pH-increase.     

Copper corrosion inhibition in O2-saturated H2SO4 solutions

Corrosion inhibition of copper in O₂-saturated 0.50 M H₂SO₄ solutions by four selected amino acids, namely glycine (Gly), alanine (Ala), valine (Val), or tyrosine (Tyr), was studied using Tafel polarization, linear polarization, impedance, and electrochemical frequency modulation (EFM) at 30 °C. Protection efficiencies of almost 98% and 91% were obtained with 50 mM Tyr and Gly, respectively. On the other hand, Ala and Val reached only about 75%. Corrosion rates determined by the Tafel extrapolation method were in good agreement with those obtained by EFM and an independent chemical (i.e., non-electrochemical) method. The chemical method of confirmation of the corrosion rates involved determination of the dissolved Cu²⁺, using ICP-AES (inductively coupled plasma atomic emission spectrometry) method of chemical analysis. Nyquist plots exhibited a high frequency depressed semicircle followed by a straight line portion (Warburg diffusion tail) in the low-frequency region. The impedance data were interpreted according to two suitable equivalent circuits. The kinetics of dissolved O₂ reduction and hydrogen evolution reactions on copper surface were also studied in O₂-saturated 0.50 M H₂SO₄ solutions using polarization measurements combined with the rotating disc electrode (RDE). The Koutecky-Levich plot indicated that the dissolved O₂ reduction at the copper electrode was an apparent 4-electron process.     

Electrochemical reactivity, surface composition and corrosion mechanisms of the complex metallic alloy Al3Mg2

A corrosion mechanism is proposed for Al₃Mg₂, based on electrochemical tests, XPS, and depth profiling using XPS and ToF-SIMS. After short (∼2 min) solution exposure, the surface consists of a surface film above dealloying. The dealloying is attributed to selective Mg dissolution and the surface rearrangement of Al into islands, although the metallic Al could alternatively be formed by two reduction reactions. The surface film thickness was ∼10 nm. After exposure to ultra-pure water, the composition was AlMg_1.3O_0.2(OH)_5.1 corresponding to Al(OH)₃·1.1 Mg(OH)₂·0.2MgO. After exposure to 0.01 M Na₂SO₄, the composition was AlMg_0.2O_0.4(OH)_2.5 corresponding to Al(OH)₃·0.1Al₂O₃·0.2MgO. Longer exposure produced a thicker surface film, more pronounced metallic Al islands and more MgH₂. Three possibilities are identified for MgH₂ formation. Al(OH)₃ formation is attributed to a precipitation reaction. Bulk nanoporous Al₃Mg₂ formation is predicted to be possible by Mg dealloying of Mg₁₇Al₁₂.     

Outdoor atmospheric corrosion of copper in Saudi Arabia

Abstract

Copper specimens have been exposed to the action of marine, marine industrial, urban and rural atmospheres of Saudi Arabia. Environmental factors such as average temperature, average relative humidity and deposition rates of atmospheric pollutants (i.e. Cl^- and SO₂) was investigated. By applying the standard ISO 9223, the aggressiveness of the atmospheres corresponding to the different test stations has been determined. Calculations of corrosion rates were made via loss of weight after one, two and three years of exposure and characterisation of the corrosion products formed on samples have been analysed using X-ray diffraction. Three main sequences have been identified on outdoor copper, representing different reaction routes in chloride dominated environments. Many kinds of patina were found on copper specimens such as cuprite (Cu₂ O), atacamite (Cu₂ Cl(OH)₃), paratacamite (Cu₂ (OH)₃Cl), copper amine nitrite hydroxide, gerhardite, copper hydroxide nitrate and copper amine nitrate.     

Corrosion evaluation and surface characterization of the corrosion product layer formed on Cu-6Sn bronze in aqueous Na2SO4 solution

The binary bronze alloy Cu-6Sn corrosion, and formation and properties of corrosion product layer (patinas) during 12 days of exposure to 15 mM Na₂SO₄ aqueous solution were investigated by a range of diverse experimental techniques. For the reasons of comparison, some techniques were applied, in parallel, to copper. Gravimetric measurements revealed lower corrosion rates of bronze than those of copper, probably caused by the presence of tin compounds in the corrosion product layer. Cyclic voltammetry results showed that the oxidation processes on bronze are affected by the formation of tin oxide species. Electrochemical impedance spectroscopy showed that, as opposed to copper which produced only two time constants, bronze corrosion resistance was dominated by the additional high-frequency time constant representing redox processes occurring at the corrosion product surface. SEM, ATR FTIR and PIXE results suggest that Cu-6Sn bronze corrosion in 15 mM Na₂SO₄ solution was impeded by the formation of two-layered structure of corrosion products that formed due to selective dissolution of copper at the layer/solution interface, leaving the outer layer enriched in highly corrosion resistant Sn oxi/hydrohide species.     

Corrosion product formation on Zn55Al coated steel upon exposure in a marine atmosphere

The formation of corrosion products on Zn55Al coated steel has been investigated upon field exposures in a marine environment. The corrosion products consisted mainly of zinc aluminium hydroxy carbonate, Zn_0.71Al_0.29(OH)₂(CO₃)_0.145·xH₂O, zinc chloro sulfate (NaZn₄(SO₄)Cl(OH)₆·6H₂O), zinc hydroxy chloride, Zn₅(OH)₈Cl₂·H₂O and zinc hydroxy carbonate, Zn₅(OH)₆(CO₃)₂ were the first three phases were formed initially while zinc hydroxy carbonate Zn₅(OH)₆(CO₃)₂ was formed after prolonged exposure in more corrosive conditions. The initial corrosion product formation was due to selective corrosion of the zinc rich interdendritic areas of the coating resulting in a mixture of zinc and zinc aluminium corrosion products.     

Hydrothermal synthesis of Cu3(OH)2V2O7·nH2O nanoparticles and its application in lithium ion battery

Well crystallized copper vanadium oxide hydroxide hydrate (Cu₃(OH)₂V₂O₇·nH₂O) nanoparticles have been successfully synthesized by a simple hydrothermal method. The morphology and structure of the as-synthesized products were characterized by field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and Raman spectroscopy. The composition of Cu₃(OH)₂V₂O₇·nH₂O was studied by thermal analysis (TG, DTA), which indicates that there are two molecules of water in a Cu₃(OH)₂V₂O₇·nH₂O molecular formula. Electrochemical properties of Cu₃(OH)₂V₂O₇·2H₂O nanoparticles as positive electrode of lithium ion battery were studied by conventional charge/discharge tests at different current density, showing steady initial discharge platforms near 1.7 V. The first discharge capacity of Cu₃(OH)₂V₂O₇·2H₂O electrode arrives at 868 and 845 mAh g⁻¹ at current density of 0.01 and 0.02 mA cm⁻², respectively.     

Corrosion behaviour of aluminium in copper containing environment

Corrosion behaviour of pure aluminium galvanically connected to metallic copper or in the presence of Cu²⁺ ions was investigated by electrochemical measurements in Na₂SO₄ and Na₂SO₄ + NaCl test solutions. It has been found that in aerated Cl⁻ ion containing solutions pitting corrosion of aluminium emerged immediately, while in the absence of oxygen this process was less violent. Effect of passivating pre-treatment of aluminium surface on corrosion behaviour Cu-Al bimetallic system is also demonstrated.     

Initial NaCl-particle induced atmospheric corrosion of zinc—Effect of CO2 and SO2

Initial corrosion and secondary spreading effects during NaCl particle induced corrosion on zinc was explored using in situ and ex situ FTIR microspectroscopy, optical microscopy, and SEM/EDAX. The secondary spreading effect which occurs upon introduction of humid air on NaCl deposited zinc surfaces was strongly dependent on the CO₂ and SO₂ content of the introduced air. Ambient level of CO₂ (350 ppm) resulted in a relatively low spreading effect, whereas the lower level of CO₂ (<5 ppm) caused a much faster spreading over a larger area. In the presence of SO₂, the secondary spreading effect was absent which could limit the cathodic process in this case. At <5 ppm CO₂, the corrosion is more localized, with the formation of simonkolleite (Zn₅(OH)₈Cl₂ · H₂O), zincite (ZnO) and sodium carbonate (Na₂CO₃), and a larger effective cathodic area. At 350 ppm CO₂, the corrosion is more general and formation of simonkolleite, hydrozincite (Zn₅(OH)₆(CO₃)₂) and sodium carbonate was observed. Sodium carbonate was mainly formed in more alkaline areas, in the inner edge of the electrolyte droplet and in the secondary spreading area. Oxidation of sulphur and concomitant sulphate formation was enhanced in the presence of NaCl particles, due to the formation of a droplet, the separation of the anodic and cathodic areas and the accompanying differences in chemical composition and pH in the surface electrolyte.     

Cathodic reduction of the duplex oxide films formed on copper in air with high relative humidity at 60 °C

The cathodic reduction of duplex air-formed oxide film on copper was performed at a constant current density of i_c = −50 μA cm⁻² in deaerated 0.1 M KCl solution to investigate the sequence of cathodic reduction of each oxide layer and its mechanism. The single-phase thick CuO film on copper was also cathodically reduced at i_c = −50 μA cm⁻² or −2.5 mA cm⁻². The surface characterizations of the air-formed oxide film and single-phase CuO film before cathodic reduction and after partial or complete cathodic reduction were performed by XPS and X-ray diffraction, respectively.The two plateau regions appeared in the potential vs. time curve during cathodic reduction of the duplex air-formed oxide film on copper, while one plateau region was observed in the potential-time curve during cathodic reduction of the single-phase CuO film on copper. The potential in the first plateau region for the air-formed film coincided with that in the plateau region for the CuO film. The results of XPS and X-ray diffraction suggested that in the first plateau region, the outer CuO layer is directly reduced to metallic Cu, while in the second plateau region, the inner Cu₂O layer is reduced to metallic Cu.