Comparison of influences of NaCl and CaCl2 on the corrosion of 11% and 17% Cr ferritic stainless steels during cyclic corrosion test

During the drying stage of the cyclic corrosion test on ferritic stainless steels in the NaCl environment, the current abruptly increased and then decreased to nearly zero, indicating that pits are initiated as the salt concentration is increased, which are then repassivated when the surface is completely dry. During the wet stage, the current remained high, suggesting that pits mainly propagate during the wet stage. In contrast, in the cyclic corrosion test in the CaCl₂ environment, the current was highest during the drying stage, indicating that the electrolyte is not completely dried and corrosion mainly propagates during the drying stage.     

In situ synchrotron X-ray micro-tomography study of pitting corrosion in stainless steel

Pitting corrosion of stainless steel has been investigated with high-resolution in situ X-ray microtomography. The growth of pits at the tip of stainless steel pins has been observed with 3D microtomography under different conditions of applied current and cell potential. The results demonstrate how pits evolve in stainless steel, forming a characteristic “lacy” cover of perforated metal. In addition, it is shown how the shape of pits becomes modified by MnS inclusions.     

Acoustic emission during pitting corrosion of 304 stainless steel

Acoustic emission (AE) during pitting corrosion of 304 stainless steel (304 SS) in H₂SO₄ solutions with different pH values and Cl⁻ concentrations was studied. Two types of AE signals are detected in all solutions. Each type of signals is characterized by AE parameters (rise time, counts number, duration and amplitude) and waveform carefully. It is believed that the hydrogen bubbles evolution inside the pits is the AE source.     

Composition changes around sulphide inclusions in stainless steels, and implications for the initiation of pitting corrosion

We report high-resolution SIMS microscopy measurements, which show that many ‘MnS’ inclusions have surrounding them a narrow ‘halo’ of half-width typically 100 nm that is strongly enriched in Fe, forcing consideration of the electrochemistry of FeS as a determinant of the behaviour of the inclusion boundary. We suggest that on exposure to water a very thin and porous metal-deficient polysulphide skin forms between the bulk of the inclusion and the steel, within which a pit can be triggered. The results resolve a controversy concerning the composition of the boundary region around inclusions in stainless steel and re-emphasise its potential significance.     

Effects of cerium on the compositional variations in and around inclusions and the initiation and propagation of pitting corrosion in hyperduplex stainless steels

Ce addition to a hyperduplex stainless steel increased its resistance to pitting corrosion because of the formation of stable Ce oxides and a decrease in the area of microcrevices between the matrix and inclusions that act as pit initiation sites. In addition, Cr-enriched zones were formed around Ce oxides with low Cr content in the Ce added alloy. Pitting corrosion in the base alloy initiated at the microcrevice and propagated to Cr oxides, which deteriorated the pitting corrosion resistance. However, pitting corrosion in the Ce added alloy propagated not to the stable Ce oxides but to the matrix.     

The influence of the cathodic process on the interpretation of electrochemical noise signals arising from pitting corrosion of stainless steels

The use of electrochemical noise (EN) measurements for the investigation and monitoring of corrosion has allowed many interesting advances in the corrosion science in recent years. A special advantage of EN measurements includes the possibility to detect and study the early stages of localized corrosion. Nevertheless, the understanding of the electrochemical information included in the EN signal is actually very limited. The role of the cathodic process on the EN signals remains uncertain and has not been sufficiently investigated to date. Thus, an accurate understanding of the influence of the cathodic process on the EN signal is still lacking. On the basis of different kinetics of the oxygen reduction it was established that the anodic amplitude of transients arising from pitting corrosion on stainless steel can be decreased by the corresponding electron consumption of the cathodic process. Therefore, the stronger the electron consumption, the weaker the anodic amplitude of the EN signal becomes. EN signals arising from pitting corrosion on stainless steel can be measured because the cathodic process is inhibited by the passive layer. This was confirmed by means of EN measurements under cathodic polarisation. Since the cathodic process plays a decisive role on the form of transients arising from pitting corrosion, its influence must be considered in the evaluation and interpretation of the EN signals.     

Microstructure and pitting corrosion resistance of annealed duplex stainless steel

The transition from metastable to stable pitting was studied in 0.5 M NaCl water solution for two cast duplex stainless steels under different microstructural conditions achieved by annealing in the range from 900 °C to 1200 °C. The ensuing microstructural changes in heat treated steels were defined and correlated with established pitting potentials (E_p) and sites of corrosion damage initiation. The variations in E_p have been discussed in terms of secondary phases precipitation. The critical condition for pit stability was quantified and used to select an appropriate microstructural state, resulting in the higher potential at which stable pit growth is first observed.     

Influence of ultrasound on pitting corrosion and crevice corrosion of SUS304 stainless steel in chloride sodium aqueous solution

The change of polarization curves and surface morphologies of SUS304 stainless steel was investigated in 3.5 mass% NaCl solution with or without the application of ultrasound (US). As the result, both the pitting corrosion and the crevice corrosion were largely suppressed by the application of US. The reason is attributed to the decrease in the concentration of hydrogen and chloride ions in pits or in the crevice by removing the corrosion product and stirring the liquid there.     

Influence of input power to vibrator and vibrator-to-specimen distance of ultrasound on pitting corrosion of SUS304 stainless steel in 3.5% chloride sodium aqueous solution

The pitting corrosion of SUSU304 steel can be suppressed by the application of a 19.5 kHz ultrasound (US) in 3.5% NaCl aqueous solution. At a constant vibrator-to-specimen distance of d = 76 mm equal to the wavelength, the suppression effect increased with the input power to vibrator and the largest effect was obtained at the power of I = 8. At constant input powers of I = 2 or 8, the suppression effect decreased with the increase in the vibrator-to-specimen distance, but the largest effect was obtained at d = 68 mm in each case of I = 2 and 8.     

Investigation of pitting corrosion of stainless steel by means of acoustic emission and potentiodynamic methods

Measurements of pitting corrosion by potentiodynamic method and also by acoustic emission technique were carried out simultaneously. Cumulative distribution function of pitting corrosion (CDF_P) occurrence was determined based on the results of potentiodynamic measurements. Independently cumulative distribution function of acoustic events (CDF_AE) was found. The correlation analysis of both distributions was also performed. The occurrence of pitting corrosion was checked by metallographic observation. The measurements proved that observable acoustic activity is an effect of hydrogen evolution inside the pits. The random character of acoustic events during polarization, statistical analysis and existence of pits are good confirmation.     

Intergranular corrosion of Ti-stabilized 11 wt% Cr ferritic stainless steel for automotive exhaust systems

Intergranular corrosion (IGC) of type 409L ferritic stainless steel (FSS) was investigated. A free-exposure corrosion and a double loop electrochemical potentiokinetic reactivation (DL-EPR) tests were conducted to examine IGC of the FSS. IGC occurred in the specimens aged at the temperature range of 400–600 °C that has the sensitization nose located around 600 °C. The critical I_r/I_a value was determined to be about 0.03 above which IGC occurred. Based on the analysis of the intergranular precipitates by an energy dispersive spectroscopy (EDS) and a transmission electron microscopy (TEM), IGC was induced by the Cr depletion zone formation due to Cr segregation around intergranular TiC.     

Effects of copper addition on the formation of inclusions and the resistance to pitting corrosion of high performance duplex stainless steels

To elucidate the effects of copper addition on the formation of inclusions and the resistance to pitting corrosion of alloys, potentiodynamic and potentiostatic polarization tests, a SEM-EDS analysis of inclusions, and thermodynamic calculations of the formation of inclusions were conducted. The addition of copper to the base alloy increased the number and area of numerous (Mn, Cr, (Al), (Fe)) oxides and oxy-sulfides due to an increase in the activity of chromium and resulted in decreased pitting resistance. The thermodynamic prediction of the formation of inclusions was in good agreement with the experimental results.     

Environmental factors affecting pitting corrosion of type 304 stainless steel investigated by electrochemical noise measurements under potentiostatic control

Electrochemical noise measurements on anodically polarised type 304 stainless steel surfaces in contact with buffer solutions of neutral pH were performed to study the effect of chloride ions in the nucleation of pitting corrosion. Passive layer stability and susceptibility to pitting corrosion after pickling and passivation at different environmental conditions were also investigated by means of electrochemical current noise measurements under cathodic and anodic polarisation. According to the obtained experimental results pits nucleate independently on the presence of chloride ions. It has been also shown that protectiveness of stainless steel surfaces after pickling strongly depends on the relative humidity of the environment in which the surface is subsequently passivated.     

Effects of solution heat-treatment and nitrogen in shielding gas on the resistance to pitting corrosion of hyper duplex stainless steel welds

The effects of solution heat-treatment and shielding gas on the pitting corrosion of hyper duplex stainless steel (HDSS) welds were investigated in highly concentrated chloride environments. The pitting resistance of a solution heat-treated HDSS after welding with an Ar shielding gas supplemented with N₂ was greatly increased due to the dissolution of Cr₂N in α-phase, which followed the diffusion of N atoms from the α-phase to the γ-phase and an increase of the γ-phase in the weld metal and heat affected zone. It was also attributed to a decrease of the pitting resistance equivalent number difference between the two phases.     

Explanation of the effect of high chloride concentration on the critical pitting temperature of stainless steel

We correlate the effect of high chloride concentration on the critical pitting temperature (CPT) of type 316L stainless steel with its effect on the critical pit solution chemistry as determined by the artificial pit technique. It is shown that the change in CPT with bulk chloride concentration (0.5-9 mol kg⁻¹) can be correlated with a change in the ratio of C^∗/C_s, where C^∗ is the critical dissolved alloy cation concentration to sustain pitting, and C_s is the solubility of FeCl₂ at the pit surface. A complicating factor is that natural pits can only grow with C^∗ = C_s at the lower chloride concentrations, but can grow without the salt film at very high chloride concentrations; this transition is believed to occur close to 5 or 6 m bulk chloride concentration. The dependence of C_s on bulk chloride concentration is given a new interpretation based on a common-ion effect operating within an altered local chemistry with complexation.     

The crevice corrosion behaviour of stainless steel in sodium chloride solution

The crevice corrosion behaviour of 13Cr stainless steel in NaCl solution was investigated mainly by electrochemical noise measurements, considering the influences of the crevice opening dimension (a) and the area ratio of the electrode outside the crevice to the one inside the crevice (r). Results show that the increase of r value prolongs the incubation period of crevice corrosion, but crevice corrosion develops rapidly once the crevice corrosion occurs. The crevice corrosion develops preferentially at the crevice bottom and then spreads to the whole electrode surface. Proton could reduce on the uncorroded area and hydrogen bubbles form inside the crevice.     

Critical pitting temperature for Type 254 SMO stainless steel in chloride solutions

The variation with time of the open circuit potential of high molybdenum containing stainless steel (Type 254 SMO) was measured in 4% sodium chloride solution in the temperatures range 30-100 °C. The plot of steady state potentials as function of temperature showed an inflection at 50 °C, attributed to the decrease of oxygen solubility in test solution above 50 °C. Potentiodynamic cycling anodic polarization technique was used to determine the critical pitting potential (E_pit) and the critical protection potential (E_prot) of the steel in 4-30% NaCl solutions at temperatures between 30 and 100 °C. By plotting the two values versus solution temperature, the corresponding critical pitting (CPT) and the critical protection (CPrT) temperatures were determined. Both parameters decreased with increasing chloride content. Above the CPT, E_pit and E_prot decreased linearly with log[Cl⁻]. The addition of bromide ions to the solution shifted both E_pit and E_prot towards positive values. In 4% NaCl, E_pit increased linearly with pH in the range 1-10. The combined effect of chloride ion concentration and pH on the morphology of the pits was examined by scanning electron microscopy (SEM) following potentiodynamic cycling anodic polarization.     

Study of the correlation between pitting corrosion and the component ratio of the dual phase in duplex stainless steel welds

Three duplex stainless steel weldments were produced by changing the chromium element to study the correlation between the pitting corrosion characteristics and the component ratio of the dual phase. The pit morphologies showed that metastable pits were generated at a lower pitting resistance equivalent number (PREN) phase. The secondary austenite phases seemed to serve as a path for the corrosive environment regardless of the ferrite number (FN). There is some discrepancy between the measured values (pitting potential (E_p) through polarization test) and expected values (sequence ranked by PREN of weaker phase) in 1 mol l⁻¹ NaCl solution at 60 °C.     

In situ 3D monitoring of corrosion on carbon steel and ferritic stainless steel embedded in cement paste

In a X-ray microcomputed tomography study, active corrosion was induced by galvanostatically corroding steel embedded in cement paste. The results give insight into corrosion product build up, crack formation, leaching of products into the cracks and voids, and differences in morphology of corrosion attack in the case of carbon steel or stainless steel reinforcement. Carbon steel was homogeneously etched away with a homogeneous layer of corrosion products forming at the steel/cement paste interface. For ferritic stainless steel, pits were forming, concentrating the corrosion products locally, which led to more extensive damage on the cement paste cover.     

Microsegregation-related pitting corrosion characteristics of AL-6XN superaustenitic stainless steel laser welds

Pitting corrosion resistance of laser welds of AL-6XN superaustenitic stainless steel (SASS) was investigated in acidic chloride ion medium. It was found that the critical pitting temperature (CPT) of the laser welds increased with increasing welding speed or decreasing laser power. Pitting attack preferentially occurred at selective dendrite cores of the laser welds. Analytical electron microscope (AEM) microanalysis revealed that depletion of Mo at dendrite cores due to microsegregation is the basic cause for the pitting corrosion susceptibility. The higher partition coefficient k_Mo and Mo concentration at dendrite cores of laser welds were attributed to the lower heat input welding parameters.