Standard electrochemical behavior of high-quality, boron-doped polycrystalline diamond thin-film electrodes

Standard electrochemical data for high-quality, boron-doped diamond thin-film electrodes are presented. Films from two different sources were compared (NRL and USU) and both were highly conductive, hydrogen-terminated, and polycrystalline. The films are acid washed and hydrogen plasma treated prior to use to remove nondiamond carbon impurity phases and to hydrogen terminate the surface. The boron-doping level of the NRL film was estimated to be in the mid 1019 B/cm3 range, and the boron-doping level of the USU films was approximately 5 x 10(20) B/cm(-3) based on boron nuclear reaction analysis. The electrochemical response was evaluated using Fe-(CN)6(3-/4-), Ru(NH3)6(3+/2+), IrCl6(2-/3-), methyl viologen, dopamine, ascorbic acid, Fe(3+/2+), and chlorpromazine. Comparisons are made between the apparent heterogeneous electron-transfer rate constants, k0(app), observed at these high-quality diamond films and the rate constants reported in the literature for freshly activated glassy carbon. Ru(NH3)6(3+/2+), IrCl6(2-/3-), methyl viologen, and chlorpromazine all involve electron transfer that is insensitive to the diamond surface microstructure and chemistry with k0(app) in the 10(-2)-10(-1) cm/s range. The rate constants are mainly influenced by the electronic properites of the films. Fe(CN)6(3-/4-) undergoes electron transfer that is extremely sensitive to the surface chemistry with k0(app) in the range of 10(-2)-10(-1) cm/s at the hydrogen-terminated surface. An oxygen surface termination severely inhibits the rate of electron transfer. Fe(3+/2+) undergoes slow electron transfer at the hydrogen-terminated surface with k0(app) near 10(-5) cm/s. The rate of electron transfer at sp2 carbon electrodes is known to be mediated by surface carbonyl functionalities; however, this inner-sphere, catalytic pathway is absent on diamond due to the hydrogen termination. Dopamine, like other catechol and catecholamines, undergoes sluggish electron transfer with k0(app) between 10(-4) and 10(-5) cm/s. Converting the surface to an oxygen termination has little effect on k0(app). The slow kinetics may be related to weak adsorption of these analytes on the diamond surface. Ascorbic acid oxidation is very sensitive to the surface termination with the most negative Ep(ox) observed at the hydrogen-terminated surface. An oxygen surface termination shifts Ep(ox) positive by some 250 mV or more. An interfacial energy diagram is proposed to explain the electron transfer whereby the midgap density of states results primarily from the boron doping level and the lattice hydrogen. The films were additionally characterized by scanning electron microscopy and micro-Raman imaging spectroscopy. The cyclic voltammetric and kinetic data presented can serve as a benchmark for research groups evaluating the electrochemical properties of semimetallic (i.e., conductive), hydrogen-terminated, polycrystalline diamond.     

Electrochemical oxidation of chlorophenols at a boron-doped diamond electrode and their determination by high-performance liquid chromatography with amperometric detection

Anodically pretreated diamond electrodes have been used for the detection of chlorophenols (CPs) in environmental water samples after high-performance liquid chromatographic (HPLC) separation. The anodization of as-deposited boron-doped polycrystalline diamond thin-film electrodes has enabled the stable determination of phenols over a wide concentration range. Prior to the HPLC analysis, a comparative study with ordinary glassy carbon, as-deposited diamond, and anodized diamond was made to examine the oxidative behavior of phenols by cyclic voltammety and flow injection analysis with amperometric detection. At anodized diamond electrodes, reproducible, well-defined cyclic voltammograms were obtained even at high CP concentration (5 mM), due to a low proclivity for adsorption of the oxidation products on the surface. In addition, after prolonged use, the partially deactivated diamond could be reactivated on line by applying a highly anodic potential (2.64 Vvs SCE) for 4 min, which enabled the destruction of the electrodeposited polymer deposits. Hydroxyl radicals produced by the high applied potential, in which oxygen evolution occurs, are believed to be responsible for the oxidation of the passivating layer on the surface. When coupled with flow injection analysis (FIA), anodized diamond exhibited excellent stability, with a response variability of 2.3% (n = 100), for the oxidation of a high concentration (5 mM) of chlorophenol. In contrast, glassy carbon exhibited a response variability of 39.1%. After 100 injections, the relative peak intensity, for diamond decreased by 10%, while a drastic decrease of 70% was observed for glassy carbon. The detection limit obtained in the FIA mode for 2,4-dichlorophenol was found to be 20 nM (S/N = 3), with a linear dynamic range up to 100 microM. By coupling with the column-switching technique, which enabled on-line preconcentration (50 times), the detection limit was lowered to 0.4 nM (S/N = 3). By use of this technique, anodized diamond electrodes were demonstrated for the analysis of CPs in drainwater that was condensed from the flue gas of waste incinerators.     

Electrochemical oxidation of histamine and serotonin at highly boron-doped diamond electrodes

The electrochemistry of histamine and serotonin in neutral aqueous media (pH 7.2) was investigated using polycrystalline, boron-doped diamond thin-film electrodes. Cyclic voltammetry, hydrodynamic voltammetry, and flow injection analysis (FIA) with amperometric detection were used to study the oxidation reactions. Comparison experiments were carried out using polished glassy carbon (GC) electrodes. At diamond electrodes, highly reproducible and well-defined cyclic voltammograms were obtained for histamine with a peak potential at 1.40 V vs SCE. The voltammetric signal-to-background ratios obtained at diamond were 1 order of magnitude higher than those obtained for GC electrodes at and above 100 microM analyte concentrations. A linear dynamic range of 3-4 orders of magnitude and a detection limit of 1 microM were observed in the voltammetric measurements. Well-defined sweep rate-dependent voltammograms were also obtained for 5-hydroxytryptamine (5-HT). The characteristics of the voltammogram indicated lack of adsorption of its oxidation products on the surface. No fouling or deactivation of the electrode was observed within the experimental time of several hours. A detection limit of 0.5 microM (signal-to-noise ratio 13.8) for histamine was obtained by use of the FIA technique with a diamond electrode. A remarkably low detection limit (10 nM) was obtained for 5-HT on diamond by the same method. Diamond electrodes exhibited a linear dynamic range from 10 nM to 100 microM for 5-HT determination and a range of 0.5-100 microM for histamine determination. The FIA response was very reproducible from film to film, and the response variability was below 7% at the actual detection limits.     

Electrochemical Oxidation of NADH at Highly Boron-Doped Diamond Electrodes

Conductive boron-doped chemical vapor-deposited diamond thin films, already known to have superior properties for general electroanalysis, including low background current and a wide potential window, are here shown to have additional advantages with respect to electrochemical oxidation of nicotinamide adenine dinucleotide (NADH), including high resistance to deactivation and insensitivity to dissolved oxygen. Cyclic voltammetry, amperometry, and the rotating disk electrode technique were used to study the reaction in neutral pH solution. Highly reproducible cyclic voltammograms for NADH oxidation were obtained at as-deposited diamond electrodes. The response was stable over several months of storage in ambient air, in contrast to glassy carbon electrodes, which deactivated within 1 h. The diamond electrode exhibited very high sensitivity for NADH, with an amperometric detection limit of 10 nM (S/N = 7). The response remained stable, even in the very low concentration range, for several months. In addition, interference effects due to ascorbic acid were minimal when the concentrations of NADH and ascorbic acid were comparable. An NADH-mediated dehydrogenese-based ethanol biosensor incorporating an unmodified diamond electrode is demonstrated. The present results indicate that diamond is a useful electrode material for the analytical detection of NADH, making it attractive for use in sensors based on enzyme-catalyzed reactions involving NADH as a cofactor.     

Direct electrochemical oxidation of disulfides at anodically pretreated boron-doped diamond electrodes

Anodically oxidized diamond electrodes have been used to oxidize disulfides, thiols, and methionine in aqueous acidic media and tested for amperometric detection of these compounds after chromatographic separation. Cyclic voltammetric signals for 1 mM glutathione disulfide (GSSG) were observed at 1.39 and 1.84 V vs SCE, the values being less positive than those of its as-deposited counterpart as well as glassy carbon electrode. The voltammetric and chronocoulometric results have indicated the high stability of the electrode with negligible adsorption. A positive shift in the peak potential with increasing pH indicated the attractive electrostatic interaction between the anodically oxidized diamond surface and the positively charged GSSG in acidic media that promoted its analytical performance. The results of the electrolysis experiments of disulfides and thiols showed that the oxidation reaction mechanism of glutathione (GSH) and GSSG involves oxygen transfer. Following separation by liquid chromatography (LC), the determination of both GSH and GSSG in rat whole blood was achieved at a constant potential (1.50 V vs Ag/AgCl), and the limits of detection for GSH and GSSG were found to be 1.4 nM (0.028 pmol) and 1.9 nM (0.037 pmol) with a linear calibration range up to 0.25 mM. These detection limits were much lower than those reported for the amperometry using Bi-PbO2 electrodes and LC-mass spectrometry, and the LC method using diamond electrodes were comparable with enzymatic assay in real sample analysis. The high response stability and reproducibility together with the possibility of regeneration of the electrode surface by on-line anodic treatment at 3 V for 30 min further support the applicability of anodically pretreated diamond for amperometric detection of disulfides.     

Integrated all-diamond ultramicroelectrode arrays: optimization of faradaic and capacitive currents

Integrated all-diamond ultramicroelectrode arrays (UMEAs) were fabricated using standard photolithography processes. The array consisted of typically 45 ultramicroelectrodes with a diameter of 10 μm and with a center-to-center spacing of 60 μm. The quasi-reference and counter electrodes were made from conductive diamond and were integrated on a 5 × 5 mm(2) chip. On the UMEA, a high ratio of faradaic current to capacitive current was achieved on heavily boron-doped and hydrogen-terminated diamond surfaces at slow scan rates and in high concentration of supporting electrolyte. A sensitive and reproducible detection of dopamine was achieved on hydrogen-terminated diamond UMEA at slow scan rates. The detection limit of dopamine in the presence of ascorbic acid was 1.0 nM, which is 50-100 times lower than that obtained on the macrosized boron-doped diamond electrodes. This array is promising for sensitive and reproducible detection of analytes in solutions with low detection limits.     

Voltammetric determination of L-cysteine at conductive diamond electrodes

Boron-doped diamond (BDD) electrodes were used to examine L-cysteine (CySH) oxidation in alkaline media. The results of the voltammetric and polarization measurements showed that at BDD electrodes the overall CySH oxidation reaction is controlled by the initial electrochemical step, i.e., the oxidation of the CyS- electroactive species. The same conclusion was supported by the results of a study of pH effects. Conversely, at glassy carbon (GC) electrodes, the same reaction is controlled by the desorption of the reaction products. These results account for the poor response for CySH determination at GC compared to BDD. It was found that BDD exhibits excellent behavior for CySH determination, clearly outperforming GC. The results demonstrate that measurement of the peak current for CySH oxidation can be used as a basis for simple method for determining CySH in the micromolar concentration range by the use of BDD electrodes.     

Fabrication and application of poly(alizarin red S)-carbon nanotubes composite film based nitrite sensor

In this work, a novel electrochemical nitrite sensor for sensitive determination of nitrite based on poly(alizarin red S)-multi-wall carbon nanotubes (PARS-MWNTs) composite film on the glassy carbon electrode was described. The surface morphologies of different electrodes were characterized by scanning electron microscopy. Cyclic voltammetry, chronocoulometry and linear sweep voltammetry were used to investigate the electrochemical response and oxidation mechanism of nitrite at the PARS-MWNTs composite film based sensor. The experimental parameters were optimized, such as electropolymerization pH value, film thickness and detection pH value et al. Under optimal working conditions, the oxidation peak current of nitrite linearly increased with its concentration in the range of 30 nM to 1.1 mM with a low detection limit of 2 nM. The PARS-MWNTs composite film based nitrite sensor was applied to the determination of nitrite in sausage, and the good recovery indicated that it may have practical applications in nitrite monitoring system.     

Development of a method for total inorganic arsenic analysis using anodic stripping voltammetry and a Au-coated, diamond thin-film electrode

We demonstrate that a Au-coated, boron-doped, diamond thin-film electrode provides a sensitive, reproducible, and stable response for total inorganic arsenic (As(III) and As(V)) using differential pulse anodic stripping voltammetry (DPASV). As is preconcentrated with Au on the diamond surface during the deposition step and detected oxidatively during the stripping step. Au deposition was uniform over the electrode surface with a nominal particle size of 23 +/- 5 nm and a particle density of 109 cm-2. The electrode and method were used to measure the As(III) concentration in standard and river water samples. The detection figures of merit were compared with those obtained using conventional Au-coated glassy carbon and Au foil electrodes. The method was also used to determine the As(V) concentration in standard solutions after first being chemically reduced to As(III) with Na2SO3, followed by the normal DPASV determination of As(III). Sharp and symmetric stripping peaks were generally observed for the Au-coated diamond electrode. LODs were 0.005 ppb (S/N = 3) for As(III) and 0.08 ppb (S/N = 3) for As(V) in standard solutions. An As(III) concentration of 0.6 ppb was found in local river water. The relative standard deviation of the As stripping peak current for river water was 1.5% for 10 consecutive measurements and was less than 9.1% over a 10-h period. Excellent electrode response stability was observed even in the presence of up to 5 ppm of added humic acid. In summary, the Au-coated diamond electrode exhibited better performance for total inorganic As analysis than did Au-coated glassy carbon or Au foil electrodes. Clearly, the substrate on which the Au is supported influences the detection figures of merit.     

Direct electrochemistry and electrocatalytic activity of cytochrome c covalently immobilized on a boron-doped nanocrystalline diamond electrode

Cytochrome c (Cyt c) was covalently immobilized on a boron-doped nanocrystalline diamond (BDND) electrode via surface functionalization with undecylenic acid methyl ester and subsequent removal of the protecting ester groups to produce a carboxyl-terminated surface. Cyt c-modified BDND electrode exhibited a pair of quasi-reversible and well-defined redox peaks with a formal potential (E(0)) of 0.061 V (vs Ag/AgCl) in 0.1 M phosphate buffer solution (pH 7.0) and a surface-controlled process with a high electron transfer constant (ks) of 5.2 +/- 0.6 s(-1). The electrochemical properties of as-deposited and Cyt c-modified boron-doped microcrystalline diamond (BDMD) electrodes were also studied for comparison. Investigation of the electrocatalytic activity of the Cyt c-modified BDND electrode toward hydrogen peroxide (H2O2) revealed a rapid amperometric response (5 s). The linear range of response to H2O2 concentration was from 1 to 450 microM, and the detection limit was 0.7 microM at a signal-to-noise ratio of 3. The stability of the Cyt c-modified BDND electrode, in comparison with that of the BDMD and glassy carbon counterpart electrodes, was also evaluated.     

Anthraquinonedisulfonate electrochemistry: a comparison of glassy carbon, hydrogenated glassy carbon, highly oriented pyrolytic graphite, and diamond electrodes

The electrochemistry of anthraquinone-2,6-disulfonate (2,6-AQDS) at glassy carbon (GC), hydrogenated glassy carbon (HGC), the basal plane of highly oriented pyrolytic graphite (HOPG), and boron-doped diamond was investigated by cyclic voltammetry and chronocoulometry. Quantitative determination of the surface coverage and qualitative assessment of the physisorption strength of 2,6-AQDS adsorption on each of these electrodes were done. The diamond and HGC surfaces are nonpolar and relatively oxygen-free, with the surface carbon atoms terminated by hydrogen. The polar 2,6-AQDS does not adsorb on these surfaces, and the electrolysis proceeds by a diffusion-controlled reaction. Conversely, the GC and HOPG surfaces are polar, with the exposed defect sites terminated by carbon-oxygen functionalities. 2,6-AQDS strongly physisorbs on both of these surfaces at near monolayer or greater coverages, such that the electrolysis proceeds through a surface-confined state. Less than 40% of the initial surface coverage can be removed by rinsing and solution replacement, reflective of strong physisorption. The results show the important role of the surface carbon-oxygen functionalities in promoting strong dipole-dipole and ion-dipole interactions with polar and ionic molecules such as 2,6-AQDS. The results also support the theory that diamond electrodes may be less subject to fouling by polar adsorbates, as compared to GC, leading to improved response stability in electroanalytical measurements. The relationship between the 2,6-AQDS surface coverage, the double-layer capacitance, and the heterogeneous electron-transfer rate constant for Fe(CN)(6)(3)(-)(/4)(-) for these four carbon electrodes is presented.     

金刚石表面的Ti、Mo、W镀层及界面反应对抗氧化性能的影响

为了提高工业金刚石的抗氧化能力,本文用XRD、SEM、DTA和TGA等方法研究了Ti、Mo、W镀层与金刚石界面反应过程、结构特征及对金刚石抗氧化性能的影响.结果表明:Ti在高于600℃、Mo在高于650℃、W在高于650℃与金刚石界面发生固相反应,通过反应扩散过程在金刚石表面外延生长成相应的TiC、MoC+Mo₂C及WC+W₂C碳化物层.该致密连续的碳化物层具有较高的抗氧化能力,延缓了金刚石表面的氧化.镀Ti、Mo、W金刚石在空气中的氧化温度达958℃、871℃和880℃.Ti、Mo、W镀层经真空碳化处理后,抗氧化温度分别达1024℃、977℃和986℃.而未镀金刚石在780℃以上即开始氧化.     

A Combined Chemical and Electrochemical Approach Using Bis(trifluoroacetoxy)iodobenzene and Glucose Oxidase for the Detection of Chlorinated Phenols

A novel electrocatalytic approach using a chemical reaction and an enzymatic reaction has been developed for the measurement of 18 chlorophenol congeners, including highly chlorinated pollutants such as pentachlorophenol, 2,3,5,6-tetrachlorophenol, 2,3,4,6-tetrachlorophenol, and several trichlorophenols. Chlorophenols were oxidized to chlorobenzoquinones with very high yields using bis(trifluoroacetoxy)iodobenzene in 0.1 M trichloroacetic acid, pH 1.5, at ambient temperature. UV-visible spectrophotometry, cyclic voltammetry, and HPLC have been used to characterize the reaction products and yields. Together with glucose oxidase immobilized on a working glassy carbon electrode (+0.45 V vs Ag/AgCl), chlorinated benzoquinones have been demonstrated to be efficient mediators in a glucose oxidase/glucose system. In this approach, glucose oxidase was readily reduced by excess glucose to provide a non-rate-limiting source of electron flow toward the electrode. The oxidation products of chlorophenols then recycled the reduced glucose oxidase to its active oxidative state, i.e., mediating the rate-limiting electron transfer from the enzyme to the electrode. At pH 3.5, linear behavior of the current response was observed up to 200 nM for all chlorophenol oxidation products. The detection limit of this method for both pentachlorophenol and 2,3,5,6-tetrachlorophenol was about 4 nM, which is close to the maximum allowable contamination level of pentachlorophenol in water samples (2.7 nM). The detection limit obtained for pentachlorophenol could also be considered superior to the result obtained with the PCP immunoassay technology (13.3 nM).     

Application of diamond microelectrodes for end-column electrochemical detection in capillary electrophoresis

Highly boron-doped diamond microelectrodes were employed in an end-column electrochemical detector for capillary electrophoresis (CE). The diamond microline electrodes were fabricated from conducting diamond thin films (exposed surface area, 300 x 50 microm), and their analytical performance as CE detectors was evaluated in a laboratory-made CE installation. The CE-ED system exhibited high separation efficiency for the detection of several catecholamines, including dopamine (DA), norepinephrine (NE), and epinephrine (E), with excellent analytical performance, for example, 155,000 theoretical plates for DA. The diamond-based electrochemical detection system also displayed low detection limits (approximately 20 nM for E at S/N = 3) and a highly reproducible current response with 10 repetitive injections of mixed analytes containing DA, NE, and E (each 50 microM), with relative standard deviations (RSD) of approximately 5%. The performance of the diamond detector in CE was also evaluated in the detection of chlorinated phenols (CP). When compared to the carbon fiber microelectrode, the diamond electrode exhibited lower detection limits in an end-column CE detection resulting from very low noise levels and highly reproducible analyses without electrode polishing due to analyte fouling, which makes it possible to perform easier and more stable CE analysis.     

Effect of oxygen terminated surface of boron-doped diamond thin-film electrode on seawater salinity sensing

Tremendous demands for highly sensitive and stable seawater salinometers have motivated intensive research on advanced electrode materials.Boron-doped diamond(BDD)is attractive in terms of its high mechanical stability and chemical inertness,but is usually hindered by its low double-layer capacitance(Cdl)for seawater salinity detection.Here,inspired by the principle of oxygen-terminated BDD electrode endowing higher Cdl than hydrogen-terminated surface,we introduce the oxygen terminated surface by oxygen plasma or reactive ion etch(RIE),and the fabricated oxygen terminated BDD electrodes demon-strate high sensitivity and long-term stability in seawater salinity detection comparing with the hydrogen terminated BDD electrodes.Significantly,the as-fabricated O-BDD-RIE electrodes not only show remark-able enhanced response even better than the commercial platinum black electrodes but also display long-time stability which is weekly verified by continuous monitor for 90 days.The outstanding per-formance of the oxygen terminated BDD electrodes can be ascribed to the enhancement of C-0 surface functional group on Cdl.In addition,a comprehensive analysis of effective electroactive surface area(EASA)and Cdl proves that the surface oxygen is the major factor for the improved Cdl.In summary,the excellent oxygen terminated BDD electrodes promise potential application in seawater salinity detection.     

Electrogenerated chemiluminescence. 66. The role of direct coreactant oxidation in the ruthenium tris(2,2')bipyridyl/tripropylamine system and the effect of halide ions on the emission intensity

We describe the electrogenerated chemiluminescence (ECL) processes of the Ru(bpy)3(2+) (bpy = 2,2'-bipyridyl)/ tripropylamine (TPrA) system at glassy carbon, platinum, and gold electrodes. The electrochemical behavior of TPrA on different electrode materials and its influence on the ECL process are demonstrated. At glassy carbon electrodes, the direct oxidation of TPrA began at approximately 0.6 V vs SCE and exhibited a broad irreversible anodic peak. Two ECL waves were observed, one in the potential region more negative than 1.0 V vs SCE and one at more positive potentials. The first ECL process apparently occurs without the electrogeneration of Ru(bpy)3(3+), in contrast to that of the second ECL wave. At Pt and Au electrodes, however, the formation of surface oxides significantly blocked the direct oxidation of TPrA. An ECL wave below 1.0 V did not appear at Pt and was very weak at gold. The ECL peaks at potentials of 1.1-1.2 V were also much weaker than those observed at the glassy carbon electrode. These results showed that the direct oxidation of TPrA played an important role in the ECL processes. Therefore, the enhancement of the TPrA oxidation current might lead to an increase in the ECL intensity. Small amounts of halide species were found to inhibit the growth of surface oxides on Pt and gold electrodes and led to an obvious increase of TPrA oxidation current. The anodic dissolution of gold in halide-containing solution was also important in activating the gold electrode surface. The electrochemical catalytic effect of bromide further promoted the oxidation of TPrA. A halide effect on ECL at Pt and Au electrodes was also evident. The most effective enhancement of ECL was observed at Au electrode in a bromide-containing solution. This effect was also found in an commercial flow-through instrument (IGEN) and provided a simple way to improve the detection sensitivity at low concentrations of Ru(bpy)3(2+).     

Conformational change detection in nonmetal proteins by direct electrochemical oxidation using diamond electrodes

In this report, we established a new electrochemical method for the detection of conformational changes in large, non-metalloproteins such as bovine serum albumin, using flow injection analysis coupled with hydrogen-terminated, boron-doped diamond electrodes. The oxidation current was used as a signal reporter in the monitoring of urea-induced BSA denaturation. In the denatured state at high urea concentrations, the electrochemical signal increased, and the amperometric responses for the oxidation potential at 1300 mV were consistent with the results of conventional methods of denaturation monitoring using fluorescence spectroscopy. The oxidation involved at least five redox-active species (cysteine, tryptophan, tyrosine, methionine, and disulfide bonds). Furthermore, the method also showed high sensitivity for quantitative analysis of protein. A linear dynamic in the concentration range 50-400 microg/mL (r(2) = 0.977) with a lower detection limit of 190 ng/mL was achieved for BSA. Direct electrochemical detection of conformation changes of proteins using BDD electrodes can be performed with advantages in terms of simplicity and sensitivity.     

Fabrication and electrocatalysis of self-assembly directed gold nanoparticles anchored carbon nanotubes modified electrode

A self-assembly directed approach was adopted to modify glassy carbon electrode (GC) with gold nanoparticles incorporation and the electrocatalytic performance of self-assembly modified electrode, GC/SA-Au-ME was critically evaluated for the oxidation of ascorbic acid (AA). The modification involves the dispersion of multi-wall carbon nanotube (MWNT) and an inclusion complex, beta-cyclodextrin-4-aminothiophenol on the surface of GC electrode in the presence of cetyltrimethylammonium bromide (CTAB). Gold nanoparticles were deposited into the self-assembled sites to fabricate the modified electrode, GC/SA-Au-ME. Another electrode (GC-Au-ME) was fabricated under similar conditions in the absence of CTAB. The electrocatalytic activity of the modified electrodes (GC/SA-Au-ME and GC-Au-ME) towards the oxidation of AA was critically compared. Cyclic voltammetry, chronoamperometry, and double potential chronoamperometry were used to evaluate the characteristics of the modified electrodes. The self-assembled electrode (GC/SA-Au-ME) shows excellent electrocatalytic activity over the other electrode, GC-Au-ME. Augmented current response, faster electron transfer kinetics (with a rate constant for electron transfer process as 3.25 x 10(4) cm3 mol(-1) s(-1)), linear range of response for the analyte (1-50 mM with an extended detection limit to 1 microM), better sensitivity, and selectivity were witnessed for the self-assembly directed modified electrode.     

Insulin oxidation and determination at carbon electrodes

The redox chemistry of insulin was investigated at glassy carbon (GC) electrodes that were coated with films of chitosan (CHIT) and multiwalled carbon nanotubes (CNT). While bare electrodes deactivated quickly during insulin oxidation, the GC electrodes coated with CHIT and CHIT-CNT films generated stable insulin currents. The GC/CHIT-CNT electrodes were used for investigating the electrooxidation process of insulin and amperometric determination of insulin. The mass spectrometric, electron paramagnetic resonance, and separation studies of electrolyzed insulin solutions suggested that the loss of 4 mass units upon insulin oxidation at CNT could be accounted for by the formation of two dityrosine cross-links intramolecularly. At a potential of 0.700 V and physiological pH 7.40, the GC/CHIT-CNT electrodes displayed a detection limit of approximately 30 nM insulin (S/N = 3), sensitivity of 135 mA M(-1) cm(-2), linear dynamic range from 0.10 to 3.0 microM (R2 = 0.995), and superior operational and long-term stability. The CNT-based electrodes are promising new insulin detectors for diabetes-related studies such as fast chromatographic analysis of therapeutic insulin formulations or evaluation of quality of pancreatic islets prior to their transplantation.     

Electron transfer from diamond electrodes to heme peptide and peroxidase

Direct electron transfer from boron-doped diamond electrodes to heme undecapeptide and horseradish peroxidase (HRP) was examined and evaluated for the application to H2O2 biosensors. As-grown and oxygen plasma-treated diamond electrodes on which heme peptide is adsorbed exhibited cathodic current responses to H2O2 on the basis of the direct electron transfer. In a comparative study of carbon electrodes on which heme peptide was adsorbed, an oxygen plasma-treated diamond electrode exhibited responses comparable with those of an edge-oriented pyrolytic graphite (EOPG) electrode, despite much smaller roughness. However, electron transfer to compounds I and II of HRP from the diamond electrodes was much slower than that from EOPG or glassy carbon, suggesting that the pi electrons of an sp2 carbon may play an important role in the direct electron transfer to the heme moiety of HRP. To examine the applicability of heme peptide-modified diamond electrodes to oxidase-based biosensors, anodic current responses of the oxygen plasma-treated diamond electrode to possible interfering agents, ascorbic acid and uric acid, were examined and compared with those of EOPG. Since the diamond electrode exhibited much less sensitivity to those interfering agents, the heme peptide-modified diamond electrode should be a promising H2O2 biosensor for the application to oxidase-based biosensors.