Techno‐economic optimization of hybrid power system using genetic algorithm

This paper presents an optimum sizing methodology to optimize the hybrid energy system (HES) configuration based on genetic algorithm. The proposed optimization model has been applied to evaluate the techno‐economic prospective of the HES to meet the load demand of a remote village in the northern part of Saudi Arabia. The optimum configuration is not achieved only by selecting the combination with the lowest cost but also by finding a suitable renewable energy fraction that satisfies load demand requirements with zero rejected loads. Moreover, the economic, technical and environmental characteristics of nine different HES configurations were investigated and weighed against their performance. The simulation results indicated that the optimum wind turbine (WT) selection is not affected only by the WT speed parameters or by the WT rated power but also by the desired renewable energy fraction. It was found that the rated speed of the WT has a significant effect on optimum WT selection, whereas the WT rated power has no consistent effect on optimal WT selection. Moreover, the results clearly indicated that the HES consisting of photovoltaics (PV), WT, battery bank (Batt) and diesel generator (DG) has superiority over all the nine systems studied here in terms of economical and environmental performance. The PV/Batt/DG hybrid system is only feasible when wind resource is very limited and solar energy density is high. On the other hand, the WT/Batt/DG hybrid system is only feasible at high wind speed and low solar energy density. It was also found that the inclusion of batteries reduced the required DG and hence reduced fuel consumption and operating and maintenance cost. Copyright © 2014 John Wiley & Sons, Ltd.     

Cost analysis of off-grid renewable hybrid power generation system on Ui Island,South Korea

Diesel engine power plants are still widely used on many remote islands in South Korea, despite their disadvantages. Aiming to solve economic and environmental pollution problems, a remote island case study was conducted on Ui Island, aiming to offer a zero-emissions solution by using renewable energy sources in an off-grid application. Power was generated from solar, wind, and hydrogen sources. Li-ion batteries and hydrogen were used as energy storage systems. In addition, PV/battery, wind/battery, PV/wind/battery, PV/battery/PEMFC, wind/battery/PEMFC, and PV/wind/battery/PEMFC systems were simulated using the HOMER software to determine the optimal sizes and techno-economic feasibility. The results show that the PV/wind/battery/PEMFC system is the best system. The configuration of the system consists of 990-kW PV panels, 700-kW wind turbines, a 1088-kWh Li-ion battery bank, 534-kW converter, 300-kW PEMWE system, 300-kg hydrogen tank, and 100-kW PEMFC system. The total NPC of the system is $5,276,069, and the LCOE is 0.366 $/kWh.     

Design and experimental performance of brackish water reverse osmosis desalination unit powered by 2 kW photovoltaic system

Small-scale brackish water reverse osmosis (BWRO) desalination units are not a major commercial success compared to its large-scale counterpart. Integrating renewable power systems with small-scale units would theoretically aid in their deployment and subsequent commercial success. In fact, RO units are constructed using a modular approach; this would allow them to adapt to a renewable power supply. Small-scale PV-RO would be a promising form of desalination system in remote areas, where BW is more common. The aim of this study is to quantify the effect of climatic-design-operation conditions on the performance and durability of a PV-BWRO desalination system. A small-scale unit is designed, constructed, and tested for 6 months. The design was limited to a 2 kWp PV power system, five different membranes, a feed TDS of 2000 mg/l, and a permeate TDS of less than 50 mg/l. Data pertaining to solar radiation and temperature were subsequently analyzed to determine their respective influences on current and future operations of the unit. The results showed that the optimum RO load, membrane type, and design configuration were 600 W, (4″x40″ TW30-4040), and a two-stage configuration, respectively. The PV system was able to supply the load without any significant disturbances; while the RO unit showed stable levels of permeate flow and salinity. Operating the PV-BWRO system for 10 h during the day would produce 5.1 m3 of fresh water at a specific energy of 1.1 kWh/m3. It was confirmed that there are many hours of high temperatures during the operation of the PV module (exceeding 45 °C) and battery room conditions (exceeding 35 °C), both of which could negatively affect the power output and battery autonomy. This negative effect is compounded annually; therefore, optimizing thermal regulation of PV modules and battery bank room conditions is essential in maintaining excellent operating temperatures.     

Potential of renewable energy development for water desalination in Tunisia

Potential renewable energy sources, which can be harnessed toward brackish and seawater desalination in Tunisia, have been evaluated. These sources of energy, mainly: solar, wind and geothermal, have been identified throughout the country and their suitability for coupling with different desalting technologies have been investigated. Renewable energies are expected to have a flourishing future and an important role in the domain of brackish and seawater desalination. Of special interest, are small desalination plants which can be operated with small quantities of energy. Small-scale renewable energy driven desalination plants might be the most economical solution for providing portable water to remote and isolated communities where the electric grid and the proper infrastructure are lacking. By exploiting renewable energies for fresh water production, three main problems can be addressed: fresh water scarcity, fossil energy depletion and environmental degradation due to gas emissions and hydrocarbon pollution.     

The importance of detailed data utilization on the performance evaluation of a grid-independent hybrid renewable energy system

In this study, a multi-source hybrid power system consisting of wind turbine (WT), photovoltaic (PV) solar unit, proton exchange membrane (PEM) FC and battery is proposed. The WT and PV generation systems are considered as the main power sources for utilizing the available renewable energy. The FC system is proposed as the back-up generation combined with electrolyzer unit and battery picks up the fast load transients and ripples. In such a hybrid system, energy management plays an important role for the overall system performance and durability. From this perspective, a fuzzy logic based intelligent controller is considered in this study. Besides, a detailed minute-scale meteorological and load demand data is utilized in the simulation process and the importance of utilization of such detailed data is presented. This detailed analysis may be valuable for evaluating the feasibility of grid-independent hybrid renewable energy units for upcoming power systems.     

Performance analysis of various hybrid renewable energy systems using battery,hydrogen, and pumped hydro‐based storage units

The aim of this research is to analyze the techno‐economic performance of hybrid renewable energy system (HRES) using batteries, pumped hydro‐based, and hydrogen‐based storage units at Sharurah, Saudi Arabia. The simulations and optimization process are carried out for nine HRES scenarios to determine the optimum sizes of components for each scenario. The optimal sizing of components for each HRES scenario is determined based on the net present cost (NPC) optimization criterion. All of the nine optimized HRES scenarios are then evaluated based on NPC, levelized cost of energy, payback period, CO₂ emissions, excess electricity, and renewable energy fraction. The simulation results show that the photovoltaic (PV)‐diesel‐battery scenario is economically the most viable system with the NPC of US$2.70 million and levelized cost of energy of US$0.178/kWh. Conversely, PV‐diesel‐fuel cell system is proved to be economically the least feasible system. Moreover, the wind‐diesel‐fuel cell is the most economical scenario in the hydrogen‐based storage category. PV‐wind‐diesel‐pumped hydro scenario has the highest renewable energy fraction of 89.8%. PV‐wind‐diesel‐pumped hydro scenario is the most environment‐friendly system, with an 89% reduction in CO₂ emissions compared with the base‐case diesel only scenario. Overall, the systems with battery and pumped hydro storage options have shown better techno‐economic performance compared with the systems with hydrogen‐based storage.     

Design and optimization of desalination reverse osmosis plants driven by renewable energies using genetic algorithms

Renewable energy sources (RES) for powering desalination processes is a promising option especially in remote and arid regions where the use of conventional energy is costly or unavailable. Reverse Osmosis (RO) is one of the most suitable desalination processes to be coupled with different renewable energy sources such as solar and wind.If RES/RO systems are optimally designed, some combinations can be cost effective and reliable. However, the design of such systems is complex because of uncertain renewable energy supplies, load demands and the non-linear characteristics of some components.In such system, different scenarios can be suggested; i.e combinations of PV panels, type and number of batteries, type and number of turbines, etc. Therefore, it is difficult to determine the optimal configuration with classical techniques. The development of a tool to integrate all parameters involved and compare between the possible scenarios is very important.This paper presents a new model based on the Genetic Algorithms allowing the generation of several individuals (possible solutions) for coupling small RO unit to RES. A particular interest is focused on the hybrid systems (PV/WIND/Batteries/RO). The objective function to minimize corresponds to the total water cost (Capital cost plus Operational costs).Finally, a case study of PV/RO unit, installed since 2007 in Ksar Ghilène village in southern Tunisia, is presented.     

Coordinated control of coastal multi-source multi-load system with desalination load: a review

Traditional seawater desalination requires high amounts of energy, with correspondingly high costs and limited benefits, hindering wider applications of the process. To further improve the comprehensive economic benefits of seawater desalination, the desalination load can be combined with renewable energy sources such as solar energy, wind energy, and ocean energy or with the power grid to ensure its effective regulation. Utilizing energy internet (EI) technology, energy balance demand of the regional power grid, and coordinated control between coastal multi-source multi-load and regional distribution network with desalination load is reviewed herein. Several key technologies, including coordinated control of coastal multi-source multi-load system with seawater desalination load, flexible interaction between seawater desalination and regional distribution network, and combined control of coastal multi-source multi-load storage system with seawater desalination load, are discussed in detail. Adoption of the flexible interaction between seawater desalination and regional distribution networks is beneficial for solving water resource problems, improving the ability to dissipate distributed renewable energy, balancing and increasing grid loads, improving the safety and economy of coastal power grids, and achieving coordinated and comprehensive application of power grids, renewable energy sources, and coastal loads.     

Optimal operation of microgrid using hybrid differential evolution and harmony search algorithm

This paper proposes the generation scheduling approach for a microgrid comprised of conventional generators, wind energy generators, solar photovoltaic (PV) systems, battery storage, and electric vehicles. The electrical vehicles (EVs) play two different roles: as load demands during charging, and as storage units to supply energy to remaining load demands in the MG when they are plugged into the microgrid (MG). Wind and solar PV powers are intermittent in nature; hence by including the battery storage and EVs, the MG becomes more stable. Here, the total cost objective is minimized considering the cost of conventional generators, wind generators, solar PV systems and EVs. The proposed optimal scheduling problem is solved using the hybrid differential evolution and harmony search (hybrid DE-HS) algorithm including the wind energy generators and solar PV system along with the battery storage and EVs. Moreover, it requires the least investment.     

Assessment of economic viability for PV/wind/diesel hybrid energy system in southern Peninsular Malaysia

This paper analyzed the potential implementation of hybrid photovoltaic (PV)/wind turbine/diesel system in southern city of Malaysia, Johor Bahru. HOMER (hybrid optimization model for electric renewable) simulation software was used to determine the technical feasibility of the system and to perform the economical analysis of the system. There were seven different system configurations, namely stand-alone diesel system, hybrid PV–diesel system with and without battery storage element, hybrid wind–diesel system with and without battery storageelement, PV–wind–diesel system with and without storage element, will be studied and analyzed. The simulations will be focused on the net present costs, cost of energy, excess electricity produced and the reduction of CO₂ emission for the given hybrid configurations. At the end of this paper, PV–diesel system with battery storage element, PV–wind–diesel system with battery storage element and the stand-alone diesel system were analyzed based on high price of diesel.     

Feasibilty study of renewable energy powered seawater desalination technology using natural vacuum technique

With an ever-increasing population and rapid growth of industrialization, there is great demand for fresh water. Desalination has been a key proponent to meet the future challenges due to decreasing availability of fresh water. However, desalination uses significant amount of energy, today mostly from fossil fuels. It is, therefore, reasonable to rely on renewable energy sources such as solar energy, wind energy, ocean thermal energy, waste heat from the industry and other renewable sources. The present study deals with the energy-efficient seawater desalination system utilizing renewable energy sources and natural vacuum technique. A new desalination technology named Natural Vacuum Desalination is proposed. The novel desalination technique achieve remarkable energy efficiency through the evaporation of seawater under vacuum and will be described in sufficient detail to demonstrate that it requires much less electric energy compared to any conventional desalination plant of fresh water production of similar capacity. The discussion will highlight the main operative and maintenance features of the proposed natural vacuum seawater desalination technology which seems to have promising techno-economic potential providing also advantageous coupling with renewable energy sources.     

Design and techno-economical optimization for hybrid PV/wind system under various meteorological conditions

The optimal design of the renewable energy system can significantly improve the economical and technical performance of power supply. In this paper, the technical-economic optimization study of a stand-alone hybrid PV/wind system (HPWS) in Corsica Island is presented.

Therefore, the primary objective of this study is to estimate the appropriate dimensions of a stand-alone HPWS that guarantee the energy autonomy of a typical remote consumer with the lowest levelised cost of energy (LCE). A secondary aim is to compare the performance and the optimal sizing of two system configurations. Finally, to study the impact of the renewable energy potential quality on the system size, the optimum dimensions of system are defined for five sites in Corsica Island. In this context, a complete sizing model is developed, able to predict the optimum system configuration on the basis of LCE. Accordingly, an integrated energy balance analysis is carried out for the whole time period investigated.

The simulation results indicate that the hybrid system is the best option for all the sites considered in this study, yielding lower LCE. Thus, it provides higher system performance than PV or wind systems alone. The choice of the system configuration type affects the state of charge variation profile, especially at low wind potential sites, while the system size and the LCE are significantly influenced. It is shown that the LCE depends largely on the renewable energy potential quality. At high wind potential site, more than 40% of the total production energy is provided by the wind generator, while at low wind potential sites, less than 20% of total production energy is generated by the wind generator.     

风光互补发电系统的优化设计(I) CAD设计方法

给出了一整套利用CAD进行风光互补发电系统优化设计的方法。为了精确确定系统每小时的运行状态,采用了更精确地表征组件特性及评估实际获得的风光资源的数学模型。为了寻找出以最小设备投资成本满足用户用电要求的系统配置,首先在风力发电机容量固定不变的前提下,计算了与该容量风力发电机匹配的不同容量的PV方阵和蓄电池所组成的风/光/蓄组合的全年功率供给亏欠率LPSP,根据总的设备投资成本最小化的原则筛选出一组与该容量风力发电机对应的满足用户给定系统供电可靠性即LPSP值的风/光/蓄组合;然后通过改变风力发电机的容量,优选出多个与不同容量风力发电机对应的既能满足用户用电要求同时总的设备购置成本又是最低的风/光/蓄组合,比较它们的成本最终唯一确定出以最小投资成本满足用户用电要求的优化的系统配置。     

Generation unit sizing and cost analysis for stand-alone wind,photovoltaic, and hybrid wind/PV systems

This paper presents the results of investigations on the application of wind, photovoltaic (PV), and hybrid wind/PV power generating systems for utilization as stand-alone systems. A simple numerical algorithm has been developed for generation unit sizing. It has been used to determine the optimum generation capacity and storage needed for a stand-alone, wind, PV, and hybrid wind/PV system for an experimental site in a remote area in Montana with a typical residential load. Generation and storage units for each system are properly sized in order to meet the annual load and minimize the total annual cost to the customer. In addition, an economic analysis has been performed for the above three scenarios and is used to justify the use of renewable energy versus constructing a line extension from the nearest existing power line to supply the load with conventional power. Annual average hourly values for load, wind speed, and insolation have been used     

Optimal sizing of autonomous hybrid energy system using supply‐demand‐based optimization algorithm

Hybrid energy systems (HESs) comprising photovoltaic (PV) arrays and wind turbines (WTs) are remarkable solutions for electrifying remote areas. These areas commonly fulfil their energy demands by means of a diesel genset (DGS). In the present study, a novel computational intelligence algorithm called supply‐demand‐based optimization (SDO) is applied to the HES sizing problem based on long‐term cost analysis. The effectiveness of SDO is investigated, and its performance is compared with that of the genetic algorithm (GA), particle swarm optimization (PSO), gray wolf optimizer (GWO), grasshopper optimization algorithm (GOA), flower pollination algorithm (FPA), and big‐bang‐big‐crunch (BBBC) algorithm. Three HES scenarios are implemented using measured solar radiation, wind speed, and load profile data to electrify an isolated village located in the northern region of Saudi Arabia. The optimal design is evaluated on the basis of technical (loss of power supply probability [LPSP]) and economic (annualized system cost [ASC]) criteria. The evaluation addresses two performance indicators: surplus energy and the renewable energy fraction (REF). The results reveal the validity and superiority of SDO in determining the optimal sizing of an HES with a higher convergence rate, lower ASC, lower LPSP, and higher REF than that of the GA, PSO, GWO, GOA, FPA, and BBBC algorithms. The performance analysis also reveals that an HES comprising PV arrays, WTs, battery banks, and DGS provides the best results: 238.7 kW from PV arrays, 231.6 kW from WTs, 192.5 kWh from battery banks, and 267.6 kW from the DGS. The optimal HES exhibits a high REF (66.4%) and is economically feasible ($104 323.10/year) and environmentally friendly. The entire load demand of the area under study is met without power loss (LPSP = 0%).     

Optimal energy management system for stand-alone wind turbine/photovoltaic/hydrogen/battery hybrid system with supervisory control based on fuzzy logic

This paper presents a novel hourly energy management system (EMS) for a stand-alone hybrid renewable energy system (HRES). The HRES is composed of a wind turbine (WT) and photovoltaic (PV) solar panels as primary energy sources, and two energy storage systems (ESS), which are a hydrogen subsystem and a battery. The WT and PV panels are made to work at maximum power point, whereas the battery and the hydrogen subsystem, which is composed of fuel cell (FC), electrolyzer and hydrogen storage tank, act as support and storage system. The EMS uses a fuzzy logic control to satisfy the energy demanded by the load and maintain the state-of-charge (SOC) of the battery and the hydrogen tank level between certain target margins, while trying to optimize the utilization cost and lifetime of the ESS. Commercial available components and an expected life of the HRES of 25 years were considered in this study. Simulation results show that the proposed control meets the objectives established for the EMS of the HRES, and achieves a total cost saving of 13% over other simpler EMS based on control states presented in this paper.     

Renewable energy systems based on hydrogen for remote applications

An integrated renewable energy (RE) system for powering remote communication stations and based on hydrogen is described. The system is based on the production of hydrogen by electrolysis whereby the electricity is generated by a 10 kW wind turbine (WT) and 1 kW photovoltaic (PV) array. When available, the excess power from the RE sources is used to produce and store hydrogen. When not enough energy is produced from the RE sources, the electricity is then regenerated from the stored hydrogen via a 5 kW proton exchange membrane fuel cell system. Overview results on the performances of the WT, PV, and fuel cells system are presented.     

Optimal capacity planning of combined renewable energy source-pumped storage and seawater desalination systems

As water scarcity is becoming a growing threat to human development, finding effective solutions has become an urgent need. To make better use of water resources, seawater desalination and storage systems using renewable energy sources (RES) are designed and implemented around the world. In this paper, an optimal capacity planning method for RES-pumped storage-seawater desalination (RES-PS-D) system is introduced. The configuration of the RES-PS-D system is clarified first, after which a cost-benefit analysis is performed using all cost and benefit components. A function for determining maximum economic benefits of the RES-PS-D system is then established, and the constraints are proposed based on various limitations. The mixed-integer linear programming algorithm is applied to solve the optimal function. A case study is introduced to validate the feasibility and effectiveness of the method. The conclusion shows that the strategy is suitable for solving the configuration optimization problem, and finally both merits and defects of the method are discussed.     

Energy storage based MG connected system for optimal management of energy: An ANFMDA technique

This paper proposes an efficient hybrid technique for the system modeling and the optimal energy management of the MG with low cost. The novelty of the proposed approach is the combination of the ANFIS and MDA named as ANFMDA that performs the decision making with the multi-objective problem. Moreover, the proposed method is the cost-effective power production of the microgrids and effective utilization of renewable energy sources without wasting the available energy. The strategy is worried about the mathematical optimization problems that include in excess of one objective function to be optimized at the same time. The MDA algorithm optimizes the MG configuration at minimum fuel cost to take care of the required load demand by using the inputs of MG like WT, PV array, MT, and ESS with corresponding cost functions. In the proposed approach, the ANFIS learning phase is employed to predict the load demand. Based on the predicted load demand the minimum annual fuel cost characteristics, the operation cost and also the replacement cost is decreased with all the subsequent points of the MDA. The performance of the proposed method is examined by comparison with the other techniques such as ABC algorithm, DA, and HOMER. The comparison results demonstrate the superiority of the proposed technique and confirm its potential to solve the problem.     

Computer-aided design of PV/wind hybrid system

A complete set of match calculation methods for optimum sizing of PV/wind hybrid system is presented. In this method, the more accurate and practical mathematic models for characterizing PV module, wind generator and battery are adopted; combining with hourly measured meteorologic data and load data, the performance of a PV/wind hybrid system is determined on a hourly basis; by fixing the capacity of wind generators, the whole year’s LPSP (loss of power supply probability) values of PV/wind hybrid systems with different capacity of PV array and battery bank are calculated, then the trade-off curve between battery bank and PV array capacity is drawn for the given LPSP value; the optimum configuration which can meet the energy demand with the minimum cost can be found by drawing a tangent to the trade-off curve with the slope representing the relationship between cost of PV module and that of the battery. According to this match calculation method, a set of match calculation programs for optimum sizing of PV/wind hybrid systems have been developed. Applying these match calculation programs to an assumed PV/wind hybrid system to be installed at Waglan island of Hong Kong, the optimum configuration and its hourly, daily, monthly and yearly performances are given.