大型风电机组模型预测独立变桨控制器设计

针对恒转速运行时,大型风电机组承受的不平衡载荷问题,提出一种多输入多输出的风电机组模型预测(MPC)独立变桨控制策略.首先,建立风电机组旋转坐标系下的状态空间模型,经过坐标变换得到固定坐标系下的平均周期模型,分析表明模型在非对角存在无法忽视的耦合;然后,计算所需观测器和控制器的参数,进一步设计基于Kalman状态观测器...     

Model predictive control for wind turbines with distributed active flaps: incorporating inflow signals and actuator constraints

This paper describes the implementation of system identification and controller design techniques using model predictive control (MPC) for wind turbines with distributed active flaps for load control. An aeroservoelastic model of the 5 MW NREL/Upwind reference wind turbine, implemented in the code DU_SWAMP, is used in an industry‐based MPC controller design cycle, involving the use of dedicated system identification techniques. The novel multiple‐input multiple‐output MPC controllers, which incorporate flap actuator constraints and the use of local inflow measurement signals, are designed and implemented for various operating points. The controllers are evaluated in standard power production load cases and fatigue load reductions up to 27.3% are achieved. The distributed flaps controller scheme is also compared with simpler single‐flap single‐input single‐output and individual pitch controller schemes. Copyright © 2011 John Wiley & Sons, Ltd.     

Overcoming fundamental limitations of wind turbine individual blade pitch control with inflow sensors

Individual pitch control (IPC) provides an important means of attenuating harmful fatigue and extreme loads upon the load bearing structures of a wind turbine. Conventional IPC architectures determine the additional pitch demand signals required for load mitigation in response to measurements of the flap‐wise blade‐root bending moments. However, the performance of such architectures is fundamentally limited by bandwidth constraints imposed by the blade dynamics. Seeking to overcome this problem, we present a simple solution based upon a local blade inflow measurement on each blade. Importantly, this extra measurement enables the implementation of an additional cascaded feedback controller that overcomes the existing IPC performance limitation and hence yields significantly improved load reductions. Numerical demonstration upon a high‐fidelity and nonlinear wind turbine model reveals (1) 60% reduction in the amplitude of the dominant 1P fatigue loads and (2) 59% reduction in the amplitude of extreme wind shear‐induced blade loads, compared with a conventional IPC controller with the same robust stability margin. This paper therefore represents a significant alternative to wind turbine IPC load mitigation as compared with light detection and ranging‐based feedforward control approaches.     

Nonlinear model predictive control of wind turbines using LIDAR

LIDAR systems are able to provide preview information of wind disturbances at various distances in front of wind turbines. This technology paves the way for new control concepts in wind energy such as feedforward control and model predictive control. This paper compares a nonlinear model predictive controller with a baseline controller, showing the advantages of using the wind predictions in the optimization problem to reduce wind turbine extreme and fatigue loads on tower and blades as well as to limit the pitch rates. The wind information is obtained by a detailed simulation of a LIDAR system. The controller design is evaluated and tested in a simulation environment with coherent gusts and a set of turbulent wind fields using a detailed aeroelastic model of the wind turbine over the full operation region. Results show promising load reduction up to 50% for extreme gusts and 30% for lifetime fatigue loads without negative impact on overall energy production. This controller can be considered as an upper bound for other LIDAR assisted controllers that are more suited for real time applications. Copyright © 2012 John Wiley & Sons, Ltd.     

Load reduction on a clipper liberty wind turbine with linear parameter‐varying individual blade pitch control

The increasing size of modern wind turbines also increases the structural loads caused by effects such as turbulence or asymmetries in the inflowing wind field. Consequently, the use of advanced control algorithms for active load reduction has become a relevant part of current wind turbine control systems. In this paper, an individual blade pitch control law is designed using multivariable linear parameter‐varying control techniques. It reduces the structural loads both on the rotating and non‐rotating parts of the turbine. Classical individual blade pitch control strategies rely on single‐control loops with low bandwidth. The proposed approach makes it possible to use a higher bandwidth since it accounts for coupling at higher frequencies. A controller is designed for the utility‐scale 2.5 MW Liberty research turbine operated by the University of Minnesota. Stability and performance are verified using the high‐fidelity nonlinear simulation and baseline controllers that were directly obtained from the manufacturer. Copyright © 2017 John Wiley & Sons, Ltd.     

Model predictive control of a wind turbine using short‐term wind field predictions

As wind turbines become larger and hence more flexible, the design of advanced controllers to mitigate fatigue damage and optimise power capture is becoming increasingly important. The majority of the existing literature focuses on feedback controllers that use measurements from the turbine itself and possibly an estimate or measurement of the current local wind profile. This work investigates a predictive controller that can use short‐term predictions about the approaching wind field to improve performance by compensating for measurement and actuation delays. Simulations are carried out using the FAST aeroelastic design code modelling the NREL 5 MW reference turbine, and controllers are designed for both above rated and below rated wind conditions using model predictive control. Tests are conducted in various wind conditions and with different future wind information available. It is shown that in above rated wind conditions, significant fatigue load reductions are possible compared with a controller that knows only the current wind profile. However, this is very much dependent on the speed of the pitch actuator response and the wind conditions. In below rated wind conditions, the goals of power capture and fatigue load control were considered separately. It was found that power capture could only be improved using wind predictions if the wind speed changed rapidly during the simulation and that fatigue loads were not consistently reduced when wind predictions were available, indicating that wind predictions are of limited benefit in below rated wind conditions. Copyright © 2012 John Wiley & Sons, Ltd.     

基于激光雷达的风力机分离测风独立变桨控制策略

在基于叶片根部载荷的PID独立变桨控制的基础上,引入激光雷达并提出优化的独立变桨控制方法.利用激光雷达可重建风力机前方风场信息的特点,对风力机前方风速进行提前测量.提出并使用统一风演化模型对所测数据进行二次处理,得到更贴近实际的叶轮中心风速,进一步使用所提出的分离测风方法对叶根载荷进行提前计算,根据载荷的计算值进行独立...     

Preview predictive control layer design based upon known wind turbine blade‐pitch controllers

The use of upstream wind measurements has motivated the development of blade‐pitch preview controllers for improving rotor speed tracking and structural load reduction beyond that achievable via conventional feedback control. Such preview controllers, typically based upon model predictive control (MPC) for its constraint handling properties, alter the closed‐loop dynamics of the existing blade‐pitch feedback control system. This can result in a deterioration of the robustness properties and performance of the existing feedback control system. Furthermore, performance gains from utilising the upcoming real‐time measurements cannot be easily distinguished from the feedback control, making it difficult to formulate a clear business case for the use of preview control. Therefore, the aim of this work is to formulate a modular MPC layer on top of a given output‐feedback blade‐pitch controller, with a view to retaining the closed‐loop robustness and frequency‐domain performance of the latter. The separate nature of the proposed controller structure enables clear and transparent quantification of the benefits gained by using preview control, beyond that of the underlying feedback controller. This is illustrated by results obtained from high‐fidelity closed‐loop turbine simulations, showing the proposed control scheme incorporating knowledge of the oncoming wind and constraints achieved significant 43% and 30% reductions in the rotor speed and flap‐wise blade moment standard deviations, respectively. Additionally, the chance of constraint violations on the rotor speed decreased remarkably from 2.15% to 0.01%, compared to the nominal controller. Copyright © 2017 John Wiley & Sons, Ltd.     

System identification and controller design for individual pitch and trailing edge flap control on upscaled wind turbines

Active load reduction strategies such as individual pitch control (IPC) and trailing edge flap (TEF) actuation present ways of reducing the fatigue loads on the blades of wind turbines. This may enable development of lighter blades, improving the performance, cost effectiveness and viability of future multi‐megawatt turbine designs. Previous investigations into the use of IPC and TEFs have been limited to turbines with ratings up to 5 MW and typically investigate the use of these load reduction strategies on a single turbine only. This paper extends the design, implementation and analysis of individual pitch and TEFs to a range of classically scaled turbines between 5 and 20 MW. In order to avoid designing controllers which favour a particular scale, identical scale‐invariant system identification and controller design processes are applied to each of the turbines studied. Gain‐scheduled optimal output feedback controllers are designed using identified models to target blade root load fluctuations at the first and second multiples of the rotational frequency using IPC and TEFs respectively. The use of IPC and TEFs is shown in simulations to provide significant reductions in fatigue loads at the blade root. Fatigue loads on non‐rotating components such as the yaw bearing and tower root (yaw moment) are also reduced with the use of TEFs. Individual pitch performance is seen to be slightly lower on larger turbines, potentially due to a combination of reduced actuator bandwidth and movement of the rotational frequency of larger turbines into a more energetic part of the turbulent spectrum. However, TEF performance is consistent irrespective of scale. Copyright © 2015 John Wiley & Sons, Ltd.     

Variable structure strategy to avoid amplitude and rate saturation in pitch control of a wind turbine

This work proposes the application of a recent compensation technique for input constraints avoidance to the pitch control of a wind turbine. The pitch angle actuators commonly present a hard limit on their rate of change together with the natural amplitude saturation, and a dynamics during their unconstrained operation that can be modeled as a first-order linear system. This dynamic behavior of the pitch actuator requires a particular design of the compensation method, which is based on variable structure systems to avoid both amplitude and rate input saturation by means of an auxiliary loop. The developed methodology reduces the pitch actuator activity necessary to regulate the generated power around its nominal value when facing sudden wind gusts. Another interesting feature of the proposal is that it allows the operator to fix conservative bounds for the actuator speed operation in order to increment the structural robustness of the wind turbine and to extend in this way the service life of the energy system. The effectiveness of the proposed strategy is evaluated by simulation results in an autonomous wind energy conversion system for water pumping with a brushless double feed induction generator (BDFIG).     

Identification in closed‐loop operation of models for collective pitch robust controller design

To achieve load reduction and power optimization, wind turbine controllers design requires the availability of reliable control‐oriented linear models. These are needed for model‐based controller design. Model identification of wind turbine while operating in closed loop is an appropriate solution that has recently shown its capabilities when linear time‐invariant controllers and complicated control structures are present. However, the collective pitch control loop, one of the most important wind turbine loops, uses non‐linear controllers. Typically, this non‐linear controller is a combination of a linear controller and a gain scheduling. This paper presents a new algorithm for identification in closed‐loop operation that allows the use of this kind of non‐linear controllers. The algorithm is applied for identification the collective pitch demand to generator speed of a wind turbine at various operating points. The obtained models are presented and discussed from a control point of view. The validity of these models is illustrated by their use for the design of a linear fix robust controller. The performance based on simulation data of this linear controller is similar to that obtained with simulations based on a linear controller with gain scheduling, but its design and implementation is much simpler. Copyright © 2012 John Wiley & Sons, Ltd.     

Wind turbine load reduction by rejecting the periodic load disturbances

For the cost per kilowatt hour to be decreased, the trend in offshore wind turbines is to increase the rotor diameter as much as possible. The increasing dimensions have led to a relative increase of the loads on the wind turbine structure; thus, it is necessary to react to disturbances in a more detailed way, e.g. each blade separately. The disturbances acting on an individual wind turbine blade are to a large extent deterministic; for instance, tower shadow, wind shear, yawed error and gravity are depending on the rotational speed and azimuth angle and will change slowly over time. This paper aims to contribute to the development of individually pitch‐controlled blades by proposing a lifted repetitive controller that can reject these periodic load disturbances for modern fixed‐speed wind turbines and modern variable‐speed wind turbines operating above‐rated. The performance of the repetitive control method is evaluated on the UPWIND 5 MW wind turbine model and compared with typical individual pitch control. Simulation results indicate that for relatively slow changing periodic wind disturbances, this lifted repetitive control method can significantly reduce the vibrations in the wind turbine structure with considerably less high‐frequent control action. Copyright © 2012 John Wiley & Sons, Ltd.     

风电叶片双作动器疲劳加载同步激振算法研究

针对双作动器驱动的风电叶片疲劳加载系统中两作动器同步控制问题,提出一种基于自抗扰控制算法的交差耦合同步控制策略;根据双作动器同步系统中同步误差与跟踪误差的控制要求,建立交叉耦合控制系统模型;进一步从安排过渡过程、跟踪估计系统状态和扰动、误差反馈及扰动补偿方面出发,利用最优控制综合函数设计一套自抗扰控制器;最后搭建一套风电叶片双作动器疲劳加载试验系统。试验结果表明,基于自抗扰控制算法的交叉耦合控制策略应用于双作动器疲劳加载系统能较好地保证作动器的速度同步性和位移同步性,受风载影响较小,系统鲁棒性强。     

极端风况下双转子风力机降载复合控制策略

为降低双转子风力机在极端风况下的大波动载荷,基于双转子风力机气动与控制仿真系统,提出了基于独立变桨自抗扰控制器和偏航模糊控制器的降载复合控制策略,并分析了正常风况和极端风况下该策略的控制效果。结果表明：与传统PID独立变桨控制相比,在极端运行阵风和极端湍流模型下,独立变桨自抗扰控制方法使叶根挥舞弯矩标准差减小18%以上;与传统恒速偏航控制相比,在极端风向变化下,偏航模糊控制方法使偏航轴承滚动力矩标准差减小约27%。降载复合控制策略有效降低了极端风况下双转子风力机的大载荷,抑制了功率波动。     

载荷优化的海上漂浮式风电机组二阶滑模变桨控制

针对强非线性、强耦合的海上漂浮式风电机组动力学系统,提出一种基于二阶滑模的统一变桨控制策略,解决受海浪风速等随机干扰引起浮式支撑平台运动而产生的疲劳结构载荷及功率波动问题。构建漂浮式风电机组的不确定仿射非线性模型,基于风电机组“额定转速”设计积分滑模面,此“额定转速”不再是恒定值,而是取决于平台纵摇速度的变量,基于超螺旋算法实现二阶滑模变桨控制律。采用FAST和Matlab/Simulink联合仿真,所提出的方案与传统PI控制相比,对稳定高风速时风力发电机功率,抑制浮式支撑平台运动及减少叶根载荷具有更好的控制作用,对塔基也有较好的减载作用。     

Sensor and actuator fault diagnosis for wind turbine systems by using robust observer and filter

In this paper, we consider sensor and actuator fault detection and estimation issues for large scale wind turbine systems where individual pitch control (IPC) is used for load reduction. The faults considered are the blade root bending moment sensor faults and blade pitch actuator faults. In the first part, with the aid of a dynamical model of the wind turbine system, a so‐called H_∞/H_? observer in the finite frequency range, is applied to generate the residual for fault detection. The observer is designed to be sensitive to faults but insensitive to disturbances, such as wind turbulence. When there is a detectable fault, the observer sends an alarm signal if the residual evaluation is larger than a predefined threshold. In addition to the fault detection, we also consider the fault estimation problem, where a dynamic filter is used to estimate the fault magnitude. The effectiveness of the proposed approach is demonstrated by simulation results for several fault scenarios. Copyright © 2010 John Wiley & Sons, Ltd.     

大型海上风电机组变桨距PID控制策略研究

文章针对大型海上风机的叶片具有较大惯性的问题,分析了传统变桨距PI控制器的不足,从而设计出带有超前环节的变桨距PID控制器,其能改善因惯性较大而导致的不良控制效果,并通过典型工况的仿真计算及性能分析,表明PID控制器的整体性能优于PI控制器,不仅具有稳定风轮转速、减轻风机振动的优点,还降低了风机的极限载荷水平,从而在保证安全性的基础上降低了机组成本。     

The Design of closed loop controllers for wind turbines

This article reviews the design of algorithms for wind turbine pitch control and also for generator torque control in the case of variable speed turbines. Some recent and possible future developments are discussed. Although pitch control is used primarily to limit power in high winds, it also has a significant effect on various loads. Particularly as turbines become larger, there is increasing interest in designing controllers to mitigate loads as far as possible. Torque control in variable speed turbines is used primarily to maximize energy capture below rated wind speed and to limit the torque above rated. Once again there are opportunities for designing these controllers so as to mitigate certain loads. In addition to improving the design of the control algorithms, it is also possible to use additional sensors to help the controller to achieve its objectives more effectively. The use of additional actuators in the form of individual pitch controllers for each blade is also discussed. It is important to be able to quantify the benefits of any new controller. Although computer simulations are useful, field trials are also vital. The variability of the real wind means that particular care is needed in the design of the trials. Copyright © 2001 John Wiley & Sons, Ltd.     

基于神经元PID的风力发电机组独立变桨控制

针对传统统一变桨距控制策略存在的不足,基于风力机空气动力学原理,提出了基于神经元PID的独立变桨距控制策略,将测量的桨叶根部My方向载荷通过神经元PID控制算出d、q轴的桨距角,经反Park变换得到3个桨叶的附加桨距角,将其与统一变桨距角相加作为独立桨距角的设定值。并借助Fast软件平台以2MW变速变桨风力发电机组为例,仿真比较了独立变桨距控制策略与统一变桨距控制策略。结果表明,独立变桨距控制策略能有效保证在额定转速下机组输出功率稳定,且能有效降低风力发电机组各零部件的疲劳载荷。     

Advanced control algorithms for reduction of wind turbine structural loads

To enable further growth of wind turbine dimensions and rated power, it is essential to decrease structural loads that wind turbines experience. Therefore a great portion of research is focused on control algorithms for reduction of wind turbine structural loads, but typically wind turbine rotor is considered to be perfectly symmetrical, and therefore such control algorithms cannot reduce structural loads caused by rotor asymmetries. Furthermore, typical approach in the literature is to use blade load measurements, especially when higher harmonics of structural loads are being reduced. In this paper, improvements to standard approach for reduction of structural loads are proposed. First, control algorithm capable of reducing structural loads caused by rotor asymmetries is developed, and then appropriate load transformations are introduced that enable presented control algorithms to use load measurements from various wind turbine components. Simulation results show that proposed control algorithm is capable of reducing structural loads caused by rotor asymmetries.