An Experimental Investigation of Semi-Interpenetrating Network Ceramic Skeleton-Reinforced Al-Alloy Composites Dry Sliding Against Cr12 Die Steel

Semi-interpenetrating network composite containing 33 vol% ceramics (5Al₂O₃·8SiO₂) and 67 vol% Al-alloy dry sliding against Cr12 cold-work die steel was measured on a SRV4 testing machine. The test procedures include the load sensitivities of the friction and wear at 70 °C and 270 °C. Test results show that the friction and wear decreased with the increase of load, whereas the specific energy conversion per countermaterial surface unit increased. The friction level and the specific energy conversion at 70 °C were superior to those at 270 °C. Scanning electron microscopy and energy dispersive X-ray spectroscopy analysis revealed at 270 °C the existence of the thicker tribofilms and, with them, more Fe oxides and less Al oxide at the worn composite surfaces in comparison with those at 70 °C. A good accordance was obtained between test and analysis results.     

Advanced Friction–Wear Behavior of Organic Brake Pads Using a Newly Developed System

The objective of this study was to investigate the influence of an advanced performance system on the tribological behavior of brake pad material using a specially designed brake pad tester system following standard SAE J-661. The tribological behavior and friction and wear characteristics of the organic brake pad samples were evaluated. During braking tests, the samples, in contact with a cast iron disk, were studied at different disc speeds, temperatures, and braking cycles under a constant pressure. In order to understand the friction and wear behavior, the unworn surfaces, worn surfaces, and wear debris were characterized by means of scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX). Furthermore, the surface characteristics and differences in the wear modes of the brake pad samples were examined. Wear debris was permitted to deform the brake pad surfaces, leading to friction layers and enabling the estimation of the friction behavior of the brake pads. The results showed that the best friction–wear behavior was obtained with lower braking cycles at low speeds and temperature. Thus, the newly developed brake pad tester system proved very effective in evaluating the performance of the brake pad samples.     

Tribological behavior of Al–Si–SiCp composites/automobile brake pad system under dry sliding conditions

Tribological behavior of stir-cast Al–Si/SiC_p composites against automobile brake pad material was studied using Pin-on-Disc tribo-tester. The Al-metal matrix composite (Al-MMC) material was used as disc, whereas the brake pad material forms the pin. It has been found that both wear rate and friction coefficient vary with both applied normal load and sliding speed. With increase in the applied normal load, the wear rate was observed to increase whereas the friction coefficient decreases. However, both the wear rate and friction coefficients were observed to vary proportionally with the sliding speed. During the wear tests, formation of a tribo-layer was observed, presence of which can affect the wear behavior, apart from acting as a source of wear debris. Tribo-layer formed over the worn disc surfaces was found to be heterogeneous in nature. Morphology and topography of worn surfaces and debris were studied using scanning electron microscope (SEM). Chemical composition of different wear products was obtained using electron probe micro analyzer (EPMA) and X-ray diffraction (XRD) techniques. Possible wear mechanisms operative in Al-MMC—brake pad tribo-couple have been discussed.     

Friction and wear performances of brake material dry sliding against a composite with a semi-interpenetrating network structure of ceramics and Al-alloy

The friction and wear performances of brake material dry sliding against semi-interpenetrating network ceramics/Al-alloy composites were determined using a SRV testing machine. For applied loads from 40-160 N, the friction decreased at 100 and 250 °C. The former friction was superior to the latter. Wear increased at 100 °C but decreased at 250 °C, and converged gradually in both cases. Friction fade took place at high temperatures, followed by overrecovery upon cooling. Higher temperatures increased wear. The proposed friction models incorporated with scanning electron microscopy and energy dispersive X-ray analysis explain the test results better.     

Wear and friction behavior of sand cast brake rotor made of A359-20 vol% SiC particle composites sliding against automobile friction material

The effect of load range of 30-100 N and speed range of 3-12 m/s on the wear and friction behavior of sand cast brake rotor made of A359-20 vol% SiC particle composites sliding against automobile friction material was investigated. Dry sliding frictional and wear behavior were investigated in a pin-on-disc type apparatus. Automobile friction material was used as pin, while the A359-20 vol% SiC particle composites formed the rotating disc. For comparison, the wear and friction behavior of commercially used cast iron brake rotor were studied. The results showed that the wear rate of the composite disc decreased with increasing the applied load from 30 to 50 N and increased with increasing the load from 50 to100 N. However, the wear rate of the composite disc decreased with increasing the sliding speed at all levels of load applied in the present work. For all sliding speeds, the friction coefficient of the composite disc decreased with applied load. The worn surfaces as well as wear debris were studied using scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analyzer and X-ray diffraction (XRD) technique. At load of 50 N and speed range of 3-12 m/s, the worn surface of the composite disc showed a dark adherent layer, which mostly consisted of constituents of the friction material. This layer acted as a protective coating and lubricant, resulting in an improvement in the wear resistance of the composite.     

Wear mechanism of multiphase friction materials with different phenolic resin matrices

Wear of the brake friction materials with straight phenolic resin, silicon modified phenolic resin, or boron–phosphorous (B–P) modified phenolic resin was investigated. A simple formulation was used to produce friction material specimens and wear tests were carried out using a Krauss type friction tester. Friction stability and wear rate of the three friction materials were compared as a function of temperature up to 400 °C and the mechanisms associated with the wear processes at different temperature ranges were analyzed using Arrhenius type plots and worn surface morphology after tests. The results showed that the wear process below the critical temperature was mainly attributed to the gradual stripping of the heat affected surface layers of the friction material, while the wear rate at elevated temperatures was determined by the detachment of subsurfaces that was caused by the thermal decomposition of the resin. Among the three friction materials investigated in this study, the friction material containing B–P modified resin showed the best wear resistance and friction stability.     

Tribological Behavior of WC-12Co Air Plasma–Sprayed Coating at Elevated Temperatures

The friction and wear performance of WC-12Co air plasma–sprayed (APS) coating at temperatures of 25–650°C under loads of 8 and 28 N in at atmospheric environment have been studied by a ball-on-disc tribometer. The effect of temperature and load on the tribological behavior of WC-Co coating was investigated. The results show that under a load of 8 N, the wear volume of the coating increases at 250°C due to the coating splat delamination and then it gradually decreases at 350–500°C. The friction could promote the formation of double oxide (CoWO₄), which is beneficial to reduce friction and wear. At higher temperatures, the wear volume increases again due to the removal of oxides. Under a load of 28 N, the wear volume of the coating increases enormously at 250°C due to the serious splat delamination. At 350°C, the load promotes double oxide formation, resulting in an early decrease in the coefficient of friction and a rapid reduction in wear volume. Although the wear volume decreases at 350–500°C, it is 10-fold higher than that under a load of 8 N. Above 500°C, the differences of the wear volumes of coatings under the two loads become less obvious, and similar trends also appear for the coefficients of friction. The synergistic effect between the load and temperature on the friction and wear mechanism of WC-12Co APS coating is discussed.     

Tribo-layer and its role in dry sliding wear of Ti–6Al–4V alloy

Dry sliding wear tests were performed for Ti–6Al–4V alloy under a load of 50–250 N at 25–500 °C on a pin-on-disk elevated temperature tester. Worn surfaces and subsurfaces were thoroughly investigated for the morphology, composition and structure of tribo-layers. Ti–6Al–4V alloy could not be considered to possess poor wear resistance at all times, and presented a substantially higher wear resistance at 400–500 °C than at 25–200 °C. The tribo-layer, a mechanical mixing layer, was noticed to exist on worn surfaces under various conditions. High wear rate at 25–200 °C was ascribed to no protective tribo-layer containing no or trace tribo-oxides. As more oxides appeared in the tribo-layers, they presented an obviously protective role due to their high hardness, thus giving a reasonable explanation for high wear resistance of Ti–6Al–4V alloy at 400–500 °C.     

Sliding Wear Characteristics of AZ91D Alloy at Ambient Temperatures of 25–200 °C

The dry sliding wear tests were performed for AZ91D alloy under the loads of 12.5–300 N and the ambient temperatures of 25–200 °C. We studied the wear characteristics of AZ91D alloy as a function of the normal load and the ambient temperature. The mild-to-severe wear transition occurred with increasing the load and the critical load reduced with the ambient temperature rising. However, no matter how high the ambient temperature was in the range of 25–200 °C, the mild wear prevailed under the lower loads. Especially, the AZ91D alloy presented a lower wear rate at 200 °C than at 25 and 100 °C under the low loads of 12.5–25 N, but vice versa under the loads of more than 25 N. These phenomena seem to be contradictory to the popular view that the mild-to-severe wear transition is controlled by the critical surface temperature. These may be attributed to a thick and hard mechanical mixing layer (MML) containing the mixture of MgAl₂O₄ and Mg on the worn surface. The MML thickened with increasing the ambient temperature (under the low loads), effectively reduced wear and markedly elevated the critical surface temperature. The oxidative wear and delamination wear successively predominated in the mild wear regime; the gross plastic-induced wear would prevail in the severe wear regime.     

Effect of Applied Load and Surface Roughness on the Tribological Properties of Ni-Based Superalloys Versus Ta<Subscript>2</Subscript>AlC/Ag or Cr<Subscript>2</Subscript>AlC/Ag Composites

The novel Ta₂AlC–20 vol.% Ag (TaAg) and Cr₂AlC–20 vol.% Ag (CrAg) composites were tribologically tested versus a Ni-based superalloy Inc718 (SA) by dry sliding at a sliding speed of 1 m/s at room temperature in air at loads from 3 N to 18 N. The TaAg composites were also tested at 8 and 18 N at 550 °C, and at a 3 N load against the SA with different surface roughnesses at 26 °C and 550 °C. At room temperatures, the coefficients of friction, μ’s, decreased from ~0.8–0.9 to ~0.3–0.4 for both the TaAg and CrAg composites as the applied normal force increased from 3 N to 8 N. Further increases in load to 18 N did not change the μ’s. The specific wear rates, sWR, increased with increased loads for the TaAg composite; they remained almost unchanged for the CrAg composite. This behavior was attributed to the formation of glaze tribofilms—similar to ones observed previously in these tribocouples at elevated temperatures and 3 N—promoted by the increased loads. Preconditioning of the SA surface by sliding against the TaAg composite at 550 °C and 8 N resulted in μ’s of <0.2 and sWR < 10⁻⁶ mm³/N-m in subsequent room temperature sliding at 3 N. Somewhat higher, but stable room temperature μ’s of ~0.3 and sWR of ~3 × 10⁻⁵ mm³/N-m were observed when the TaAg composites were slid versus a sandblasted SA surface at 500 °C and 3 N. It follows that in situ preconditioning of the tribo-surfaces is a powerful tool for improving the properties of the MAX/Ag-SA tribocouples. The relationship between sliding conditions, chemistries of tribofilms, and their properties are discussed.     

Ionic liquids as a neat lubricant applied to steel–steel contacts

This paper studies the use of 3 ionic liquids ([(NEMM)MOE][FAP], [BMP][FAP] and [BMP][NTf₂]) as neat lubricant within steel–steel contact conditions. Tribological tests (at 40 and 100 °C) were conducted in a HFRR tribometer and hence a complementary study was developed using a MTM tribometer. The wear surface on the discs was measured after the HFRR tests by confocal microscopy and also analyzed by SEM and XPS. The [BMP][NTf₂] showed the lowest friction coefficient in the MTM and HFRR tests at 40 °C but at 100 °C its tribological behavior worsened due to its lowest viscosity. Similar results were found for wear behavior. Both antifriction and antiwear results were related to the tribofilms formation from the ECR and XPS measurements.     

Friction and wear behavior of Ni-P coated Si3N4 reinforced Al6061 composites

Al6061 matrix composite reinforced with nickel coated silicon nitride particles were manufactured by liquid metallurgy route. Microstructure and tribological properties of both matrix alloy and developed composites have been evaluated. Dry sliding friction and wear tests were carried out using pin on disk type machine over a load range of 20-100 N and sliding velocities of range 0.31-1.57 m/s. Results revealed that, nickel coated silicon nitride particles are uniformly distributed through out the matrix alloy. Al6061-Ni-P-Si₃N₄ composite exhibited lower coefficient of friction and wear rate compared to matrix alloy. The coefficient of friction of both matrix alloy and developed composite decreased with increase in load up to 80 N. Beyond this, with further increase in the load, the coefficient of friction increased slightly. However, with increase in sliding velocity coefficient of friction of both matrix alloy and developed composite increases continuously. Wear rates of both matrix alloy and developed composites increased with increase in both load and sliding velocity. Worn surfaces and wear debris was examined using scanning electron microscopy (SEM) for possible wear mechanisms. Energy dispersive spectroscope (EDS), X-ray diffraction (XRD) and X-ray photoelectron spectroscope (XPS) techniques were used to identify the oxides formed on the worn surfaces and wear debris.     

Hot wear properties of ceramic and basalt fiber reinforced hybrid friction materials

In the present study, hybrid friction materials were manufactured using ceramic and basalt fibers. Ceramic fiber content was kept constant at 10 vol% and basalt fiber content was changed between 0 to 40 vol%. Mechanical properties and friction and wear characteristics of friction materials were determined using a pin-on-disc type apparatus against a cast iron counterface in the sliding speeds of 3.2–12.8 m/s, disc temperature of 100–350 °C and applied loads of 312.5–625 N. The worn surfaces of the specimens were examined by SEM. Experiments show that fiber content has a significant influence on the mechanical and tribological properties of the composites. The friction coefficient of the hybrid friction materials was increased with increasing additional basalt fiber content. But the specific wear rates of the composites decreased up to 30 vol% fiber content and then increased again above this value. The wear tests showed that the coefficient of friction decreases with increasing load and speed but increases with increasing disc temperature up to 300 °C. The most important factor effecting wear rate was the disc temperature followed by sliding speed. The materials showing higher specific wear rates gave relatively coarser wear particles. XRD studies showed that Fe and Fe₂O₃ were present in wear debris at severe wear conditions which is indicating the disc wear.     

Friction Reduction and Antiwear Capacity of Engine Oil Blends Containing Zinc Dialkyl Dithiophosphate and Molybdenum-Complex Additives

The efficacy of oil blends containing zinc dialkyl dithiophosphate (ZnDTP) and molybdenum (Mo)-complex additives to improve the tribological properties of boundary-lubricated steel surfaces was investigated experimentally. The performance of oil blends containing three different types of Mo-complex additives of varying Mo and S contents with or without primary/secondary ZnDTP additions were investigated at 100°C. The formation of antiwear tribofilms was detected in situ by observing the friction force and contact voltage responses. Wear volume and surface topography measurements obtained from surface profilometry and scanning electron microscopy studies were used to quantify the antiwear capacity of the formed tribofilms. The tribological properties are interpreted in terms of the tribofilm chemical composition studied by X-ray photoelectron spectroscopy. The results demonstrate that blending the base oil only with the Mo-compound additives did not improve the friction characteristics. However, an optimum mixture of Mo complexes and ZnDTP additive provided sufficient amounts of S and Mo for the formation of antiwear tribofilms containing low-shear strength MoS ₂ that reduces sliding friction. In addition, the formation of a glassy phosphate phase due to the synergistic effect of the ZnDTP additive enhances the wear resistance of the tribofilm. This study shows that ZnDTP- and Mo-containing additives incorporated in oil blends at optimum proportions improve significantly the tribological properties of boundary-lubricated steel surfaces sliding at elevated temperatures.     

Sliding wear transition for the CW614 brass alloy

Dry sliding wear tests were performed on a CW614 brass alloy using a pin-on-ring configuration. Wear kinetics were measured within a load range of 20–80 N and sliding velocity ranging from 1 to 7 m/s. Chemical compositions, morphologies and microstructures of worn surfaces and wear debris were characterised by scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS). Two main wear regimes have been observed: severe wear and mild wear. The results of wear tests and metallographic investigations on worn surfaces have been summarised in a wear mechanism map. It was found that the wear transition is controlled by a critical temperature at the contact surface.     

Characterization and tribological investigation of sol–gel ceramic films on Ti–6Al–4V

SiO₂, TiO₂, and hydroxyapatite (HA) thin films with good biocompatibility were grown on Ti–6Al–4V (coded as TC4) substrate by sol–gel and dip-coating processes from specially formulated sols, followed by annealing at 500 °C The chemical states of some typical elements in the target films were detected by means of X-ray photoelectron spectroscopy (XPS). Atomic force microscopy (AFM) and high-resolution scanning electron microscopy (SEM) are applied to characterize the original unworn films. The tribological properties of thin films sliding against an AISI52100 steel ball were evaluated on a reciprocating friction and wear tester. As the result, the target films composed of nano-particles ranging from 30 nm to 100 nm around were obtained. All the sol–gel ceramic films are superior in resisting wear compared with the TC4 substrate. Among all, HA film shows the best resistance while SiO₂ film shows the worst wear resistance both under higher (3 N) and lower load (1 N). TiO₂ shows good wear resistance under lower load (1 N). SEM observation of the morphologies of worn surfaces indicates that the wear of TC4 is characteristic of abrasive wear. Differently, abrasion, plastic deformation and micro-fracture dominate the wear of ceramic films. The superior friction reduction and wear resistance of HA film is greatly due to the slight plastic deformation of the film. It is supposed that the deformation of the HA film is closely related to the special arrangement of the nano-particles and microstructure. HA film is recommended for clinical application from the point of wear resistance view.     

On the dry and wet sliding performance of potentially new frictional brake pad materials for automotive industry

In this work, dry and wet continuous sliding performances of newly developed four different non-commercial frictional brake pad materials (NF1, NF2, NF4, and NF5) were evaluated and compared with other two chosen commercial brake pad materials (CMA and CMB) using a small-scale tribo-tester of pad-on-disc type.Results showed that under dry continuous braking, friction coefficients for all non-commercial brake pad materials including the CMB were insensitive to the type of brake pad materials. In addition, all brake pad materials showed a slight increase in the friction coefficients (5–19%) with increasing pressure or speed. Meanwhile, the wear rates were substantially dependent on the type or ingredient of brake pad materials and the pressure. Conversely, under wet sliding condition, the friction coefficients were decreased by a factor of 2. Moreover, no evidence of HD water film could be evidenced as the measured friction coefficient values were in the order of dry friction. Thus, the wet results suggested that the friction behaviour was influenced by factors other than HD film, and the values of friction coefficient were in the range of dry friction, mixed and boundary lubrication friction. Qualitative assessment of the SEM morphologies of brake pad surfaces showed that tribofilms were easily formed in dry braking and hardly formed in wet braking. Besides, all brake pad rubbing surfaces showed contact plateaus “patches” and disintegrations of various sizes and locations depending on the braking condition. Furthermore, the removal of material was associated with either mechanical crushing action performed by entrapped wear debris or due to disintegration of plateaus which were accelerated by spraying the water.     

Tribological surfaces of organic brake pads

Despite the enormous amount of testing and development of automotive brakes and brake pad materials, rather little is known about their tribological contact situation on a microscopic level. The sliding of an organic brake pad against a grey cast iron rotor is very different from most tribological systems. When worn against the rotor, the complex structure and very inhomogeneous composition of the pads results in a particular surface structure, with large contact plateaus rising a few micrometers above the rest of the surface [Wear 232 (1999) 163; Wear 2000 (submitted for publication); Proceedings of the Nordtrib 2000, vol. 2 (2000), 358]. The present investigation involves a more comprehensive study of the formation, mechanical properties and composition of the tribological surfaces of such pads, using high resolution scanning electron microscopy, nanoindentation, energy dispersive X-ray analysis and three-dimensional profilometry using white light optical interferometry. The observations are discussed and correlated to observed friction phenomena.     

Wear and corrosion wear of medium carbon steel and 304 stainless steel

Wear and corrosive wear involve mechanical and chemical mechanisms and the combination of these mechanisms often results in significant mutual effects. In this paper, tribological behavior, X-ray peak broadening, and microstructure changes of carbon steel AISI 1045 and stainless steel AISI 304 samples under simultaneous wear and corrosion were investigated and the results were compared with those obtained from dry wear tests. 3.5 wt.% NaCl solution was used as the corrosion agent and a pin-on-disk tribometer was employed to perform wear and corrosive wear tests.X-ray diffraction measurements have shown that by increasing the applied load, the worn surfaces of carbon steel samples reached a constant strain at which fracture and wear occurred. Whereas in 304 stainless steel samples, by increasing the applied load, broadening of X-ray diffraction peaks was decreased.Wear tests of carbon steel and stainless steel samples have shown smaller weight losses and lower friction coefficient in the presence of corrosive environment. Study of worn surfaces suggested that depending on wear environment and applied load, different features of wear mechanisms were involved.     

Effect of Temperature on Tribological Properties and Wear Mechanisms of NiAl Matrix Self-Lubricating Composites Containing Graphene Nanoplatelets

Studies have been carried out to explore the friction and wear behaviors of NiAl matrix self-lubricating composites containing graphene nanoplatelets (NG) against an Si₃N₄ ball from 100 to 600°C with a normal load of 10 N and a constant speed of 0.2 m/s. The results show that NG exhibits excellent tribological performance from 100 to 400°C compared to NiAl-based alloys. A possible explanation for this is that graphene nanoplatelets (GNPs) contribute to the formation of a friction layer, which could be beneficial to the low friction coefficient and lower wear rate of NG. As the temperature increases up to 500°C, the beneficial effect of GNPs on the tribological performance of NG becomes invalid due to the oxidation of GNPs, resulting in severe adhesive wear and degradation of the friction layer on the worn surface of NG. GNPs could hold great potential applications as an effective solid lubricant to promote the formation of a friction layer and prevent severe sliding wear below 400°C.