离子束能量和衬底温度对氧化钆结构的影响

利用双离子束沉积技术,在Si(100)衬底上制备了氧化钆薄膜.离子束能量在100～500eV范围内,衬底温度较低时薄膜为(402)择优取向的单斜结构,随着衬底温度的增加,择优取向转为(202)方向.当衬底温度是700℃时,出现了立方结构,这是由于离子束加热的作用,导致低温下出现单斜结构.XPS研究表明薄膜中存在氧缺陷,改进工艺条件可消除部分缺陷.     

离子束能量和衬底温度对氧化钆结构的影响

利用双离子束沉积技术,在Si(100)衬底上制备了氧化钆薄膜.离子束能量在100～500eV范围内,衬底温度较低时薄膜为(402)择优取向的单斜结构,随着衬底温度的增加,择优取向转为(202)方向.当衬底温度是700℃时,出现了立方结构,这是由于离子束加热的作用,导致低温下出现单斜结构.XPS研究表明薄膜中存在氧缺陷,改进工艺条件可消除部分缺陷.     

低温下磁控溅射AIN薄膜择优取向研究

研究了衬底温度从-20～20℃下射频磁控溅射A1N薄膜的择优取向程度.利用X线衍射(XRD)、原子力显微镜(AFM)和场发射电子显微镜(FESEM)对A1N薄膜的晶体结构、租糙度及表面和断面形貌进行了分析.研究结果表明,当衬底温度低于0℃时,AIN薄膜中的(100)衍射峰消失,A1N薄膜以(002)面择优取向生长.当衬底温度降低时,AIN薄膜的晶粒大小和表面粗糙度减小.AIN薄膜在0℃下沉积具有最佳的择优取向程度和较低的表面粗糙度.     

适用SAW器件的ZnO/Ti/Si薄膜制备及缺陷分析

在Si(100)衬底和Ti/Si(100)衬底上分别制备了ZnO薄膜,探讨了Ti缓冲层对ZnO薄膜结构和缺陷的影响,利用X射线衍射(XRD)测试了ZnO薄膜的晶体结构及择优取向,利用原子力显微镜(AFM)观察ZnO薄膜的表面粗糙度(RMS),利用光致发光(PL)光谱检测了ZnO薄膜的缺陷,利用四探针法测试了ZnO薄膜的电阻率。结果表明,在Ti/Si(100)衬底上、衬底温度350℃的条件下,制备的ZnO薄膜表面光滑、缺陷少、电阻率高且具有高C轴取向。本文这一工作对于压电薄膜缺陷分析及高性能ZnO的声表面波(SAW)器件研制有重要意义。     

基于热光伏电池GaSb多晶薄膜的可控生长

采用物理气相沉积(PVD)法在ITO透明导电衬底上制备GaSb多晶薄膜.研究了衬底温度及薄膜厚度对GaSb薄膜结构特性、电学特性以及光学特性的影响.在一定条件下生长的GaSb薄膜择优取向由GaSb(111)晶向转变为GaSb(220)晶向, 这是在玻璃衬底上生长GaSb薄膜没有发现的现象.择优取向改变为(220)晶向的GaSb薄膜具有更高的霍尔迁移率.因为这种薄膜材料具有更少的晶粒间界和更少的缺陷.经优化后的GaSb薄膜的光学吸收系数在104 cm-1以上, 适用于热光伏薄膜太阳电池中.     

DC磁控溅射制备的TiNx薄膜组分及性能分析

利用DC磁控溅射法在p-Si(111)衬底上制备了TiNx薄膜.利用X射线能谱仪(EDX)、X射线衍射(XRD)、紫外/可见分光光度计、四探针电阻率测试仪等分析了薄膜的组分、结构和光电特性.结果表明,薄膜中N/Ti原子比接近于1;衬底温度对薄膜的择优取向影响显著,240℃附近是TiNx薄膜结晶择优取向由(111)向(200)转变的临界点;薄膜在近红外波段平均反射率随衬底温度的升高,先增大后减小;薄膜的电阻率随着衬底温度的升高而显著降低.     

基于热光伏电池GaSb多晶薄膜的可控生长（英文）

采用物理气相沉积(PVD)法在ITO透明导电衬底上制备GaSb多晶薄膜.研究了衬底温度及薄膜厚度对GaSb薄膜结构特性、电学特性以及光学特性的影响.在一定条件下生长的GaSb薄膜择优取向由GaSb(111)晶向转变为GaSb(220)晶向,这是在玻璃衬底上生长GaSb薄膜没有发现的现象.择优取向改变为(220)晶向的GaSb薄膜具有更高的霍尔迁移率.因为这种薄膜材料具有更少的晶粒间界和更少的缺陷.经优化后的GaSb薄膜的光学吸收系数在104cm~(-1)以上,适用于热光伏薄膜太阳电池中.     

衬底温度对ZnO薄膜氧缺陷的影响

采用射频磁控溅射在石英玻璃和单晶硅Si(100)衬底上制备了ZnO薄膜，研究了衬底温度对ZnO薄膜中氧缺陷的影响。实验发现，ZnO薄膜c轴取向性随温度的升高而增强；当衬底温度达到550。C时，XRD谱上仅出现一个强的(002)衍射峰和一个弱的(004)衍射峰，显示ZnO具有优异c轴取向性。同时，随着温度的升高，ZnO薄膜的紫外透射截止边带向高波长方向漂移，其电导率也随衬底温度的升高逐渐增大，表明薄膜中的氧缺陷逐渐增多。这种氧缺陷是由于ZnO的氧平衡分压高于Zn所致，可通过提高溅射气体中氧含量来改善。     

硅基AlN薄膜制备技术与测试分析

采用直流磁控反应溅射法,在Si(100),Al/Si(100)和Pt/Ti/Si(100)等多种衬底上制备了用于MEMS器件的AlN薄膜.用XRD和AES对薄膜的结构和组分进行了分析,通过优化工艺参数,得到了提高薄膜择优取向的方法,并分析了不同衬底上AlN晶粒生长的有关机理.制备的AlN薄膜显示出良好的〈002〉择优取向性,摇摆曲线的半高宽达到5.6°.     

射频磁控溅射参数对 Ba0.7Sr0.3TiO3薄膜结构和性能的影响

采用射频磁控溅射法在 Pt/TiO2/SiO2/Si(100) 衬底上制备了Ba0.7Sr0.3TiO3薄膜,研究了工作气压、衬底温度等溅射参数对Ba0.7Sr0.3TiO3薄膜结构和电学性质的影响.使用 XRD 分析了工作气压为 2Pa、衬底温度分别为 200 ℃、400 ℃、600℃(组a),以及衬底温度为600℃、工作气压分别为 1.5Pa、2.0Pa、2.5Pa、3.0Pa 和 5.0Pa (组b)两组薄膜的微结构,结果表明工作气压在 2.5Pa 以下、衬底温度为 600℃时沉积的薄膜具有较好的钙钛矿结构.在 1.5Pa 条件下溅射的薄膜具有明显的(111)择优取向.在2.5Pa时,Pt/Ba0.7Sr0.3TiO3/Pt电容有最优铁电性能,在外加4 V电压(电场为 80 kV/cm)下,剩余极化 (Pr) 和矫顽场(Ec)分别为 2.32 μC/cm2、21.1 kV/cm.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks     

Call for Papers—Feature Topic,Vol.12,No.7,2015

正Information Centric Networking Information-Centric Networking(ICN) is an emerging direction in Future Internet architecture research,gaining significant tractions among academia and industry.Aiming to replace the conventional host-to-host communication model by a data-centric model,ICN treats data content as the first