Raman Spectroscopic Study of Gallium-Doped Ba(Zn1/3Ta2/3)O3

Resonators of Ba(Zn_1/3Ta_2/3)O₃, sintered between 1450° and 1600°C, are characterized by Raman spectroscopy, X-ray diffraction, and scanning electron microscopy. The quality factors of the resonators are found to depend on sintering temperature, and at 1600°C there is evidence of Zn loss from the surface. The frequency of the A_1g Raman mode changes from 800.9 cm⁻¹ for a sample with Q = 80000 (2 GHz), to 794.5 cm⁻¹ when Q = 44000 (2 GHz). Changes in the position of this and other Raman modes are thought to be due to distortions of the oxygen octahedra, brought about by Zn loss. The presence of a BaTa₂O₆ phase at the surface is confirmed by XRD and SEM.     

Influence of Non-Stoichiometry on the Structure and Properties of Ba(Zn1/3Nb2/3)O3 Microwave Dielectrics: I. Substitution of Ba3W2O9

A narrow region of Zn-vacancy-containing cubic perovskites was formed in the (1− x )Ba₃(ZnNb₂)O₉−( x )Ba₃W₂O₉ system up to 2 mol% substitution ( x =0.02). The introduction of cation vacancies enhanced the stability of the 1:2 B-site ordered form of the structure, Ba(Zn_{1− x} □ _x )_1/3(Nb_{1− x} W _x )_2/3O₃, which underwent an order–disorder transition at 1410°C, ∼35° higher than pure Ba(Zn_1/3Nb_2/3)O₃. The Zn vacancies also accelerated the kinetics of the ordering reaction, and samples with x =0.006 comprised large ordered domains with a high lattice distortion ( c/a =1.226) after a 12 h anneal at 1300°C. The tungstate-containing solid solutions can be sintered to a high density at 1390°C, and the resultant ordered ceramics exhibit some of the highest microwave dielectric Q factors ( Q × f =1 18 000 at 8 GHz) reported for a niobate-based perovskite.     

Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

Low-Temperature Sintering and Piezoelectric Properties of (Na0.5K0.5)NbO3 Lead-Free Piezoelectric Ceramics

(Na_0.5K_0.5)NbO₃ (NKN) ceramic with 1.5 mol% CuO added (NKNC) was well sintered even at a low temperature of 900°C with the addition of ZnO. Most of the ZnO reacted with the CuO and formed the liquid phase that assisted the densification of the specimens at 900°C. A few Zn²⁺ ions entered the matrix of the specimens and increased the coercive field ( E _c) and Q _m values of the specimens. High-piezoelectric properties of k _p=0.37, Q _m=755, and ɛ₃ ^T /ɛ₀=327 were obtained from the NKNC ceramics containing 1.0 mol% ZnO sintered at 900°C for 2 h.     

Nonlinear Optical Properties of TeO2-Based Glasses: La2O3-TeO2 Binary Glasses

The third-order nonlinear optical susceptibilities, X⁽³⁾, of the xLaO_1.5·(100 – x)TeO₂ binary glasses have been measured by the third harmonic generation (THG) method. In order to investigate the origin of high-intensity third harmonic generation, the various optical properties, such as nonlinear refractive index ( n ₂), Abbe number ( v _d), dispersion energy ( E _d), average excitation energy ( E ₀), (energy gap ( E _g), and polarizability (α_m), have been estimated from the refractive index and UV-visible absorption spectrum measurements. The linear refractive index, polarizability, and E _d/ E ₀² increased, and Abbe number and energy gap decreased, with increasing LaO_1.5 content. The nonlinear optical susceptibility X⁽³⁾ is discussed in relation to these optical parameters.     

Effect of CuO on the Sintering Temperature and Piezoelectric Properties of (Na0.5K0.5)NbO3 Lead-Free Piezoelectric Ceramics

When a small amount of CuO was added to (Na_0.5K_0.5)NbO₃ (NKN) ceramics sintered at 960°C for 2 h, a dense microstructure with increased grains was developed, probably due to liquid-phase sintering. The Curie temperature slightly increased when CuO exceeded 1.5 mol%. The Cu²⁺ ion was considered to have replaced the Nb⁵⁺ ion and acted as a hardener, which increased the E _c and Q _m values of the NKN ceramics. High piezoelectric properties of k _p=0.37, Q _m=844, and ɛ₃ ^T /ɛ₀=229 were obtained from the specimen containing 1.5 mol% of CuO sintered at 960°C for 2 h.     

Infrared Reflection of Ba(Mg1/3Ta2/3)O3 Ceramics

The dielectric function of the ordered Ba(Mg_1/3Ta_2/3)O₃ ceramics was investigated by the infrared reflectance spectra taken over the 50–4000-cm⁻¹ range. The detailed crystal structure of the specimen was examined by the Rietveld method. The space group of trigonal D _3d³ and the degree of long-range order of 0.97 for Mg and Ta atomic arrangement were confirmed. The reflectance spectra were analyzed on the basis of the four-parameter semiquantum model assuming 16 infrared active vibrational modes allowed for the related D _3d³ structure. The lowest-frequency optical mode was found at 60 cm⁻¹, which can be assumed to involve the motions of the heavy TaO₆ octahedra.     

Double Precursor Solution Coating Approach for Low-Temperature Sintering of [Pb(Mg1/3Nb2/3)O3]0.63[PbTiO3]0.37 Solids

Lead-based piezoelectric ceramics typically require sintering temperatures higher than 1000°C at which significant lead loss can occur. Here, we report a double precursor solution coating (PSC) method for fabricating low-temperature sinterable polycrystalline [Pb(Mg_1/3Nb_2/3)O₃]_0.63-[PbTiO₃]_0.37 (PMN–PT) ceramics. In this method, submicrometer crystalline PMN powder was first obtained by dispersing Mg(OH)₂-coated Nb₂O₅ particles in a lead acetate/ethylene glycol solution (first PSC), followed by calcination at 800°C. The crystalline PMN powder was subsequently suspended in a PT precursor solution containing lead acetate and titanium isopropoxide in ethylene glycol to form the PMN–PT precursor powder (second PSC) that could be sintered at a temperature as low as 900°C. The resultant d ₃₃ for samples sintered at 900°, 1000°, and 1100°C for 2 h were 600, 620, and 700 pm/V, respectively, comparable with the known value. We attributed the low sintering temperature to the reactive sintering nature of the present PMN–PT precursor powder. The reaction between the nanosize PT and the submicrometer-size PMN occurred roughly in the same temperature range as the densification, 850°–900°C, thereby significantly accelerating the sintering process. The present PSC technique is very general and should be readily applicable to other multicomponent systems.     

Synthesis of Ba(Mg1/3Ta2/3)O3 Microwave Ceramics through a Sol–Gel Route Using Acetate Salts

A sol–gel process to unsophisticatedly synthesize Ba(Mg_1/3Ta_2/3)O₃ (BMT) ceramics at low cost has been developed in the present work. This process involves the reaction of TaCl₅ with acetates of Ba and Mg in the presence of citric acid. Pure BMT polycrystalline powders can be obtained by calcining the synthesized products at 1000°C. The BMT powders were found to have a primary particle size as small as 100 nm. BMT ceramics with favorable structural characteristics can be obtained from sintering of the sol–gel BMT at temperatures much lower than that for the conventional solid-state BMT. Sintering the sol–gel BMT in pellet form at 1300°C resulted in an ordering parameter of 0.72 for the pellet, and a relative density of >95% was achieved with sintering at 1500°C. The grain size of the sintered sol–gel BMT was large and uniform in comparison with the products from the solid-state method. Using the sol–gel route, sintering at temperatures as low as 1400°C gave ceramics with acceptable microwave dielectric properties (a dielectric constant of 16 and Qf factor of 14 400 GHz), while higher temperatures (>1600°C) are needed for the solid-state route to give similar properties.     

Raman Study of Glasses of Ba2TiSi2O8 and Ba2TiGe2O8

Raman spectra are reported for fresnoite (Ba₂Ti(Si,Ge)₂O₈ glasses, and comparison is made between the Raman spectra of the corresponding crystalline powders and glasses of Ba₂TiSi₂O₈ and Ba₂TiGe₂O₈. The Ba₂TiGe₂O₈ glass spectra show correspondence with the Ba₂TiGe₂O₈ crystalline Raman spectra; the v _s(Ge–O–Ge) mode occurs at 518 cm⁻¹ in the glass and at 521 cm⁻¹ in the crystalline material. Five-fold coordinated titanium is the majority species present in the Ba₂TiGe₂O₈ glass as revealed by a strong band at 824 cm⁻¹ in the I glass spectrum. The Ba₂TiSi₂O₈ glass spectra are similar to the Ba₂TiSi₂O₈ crystalline spectrum; the strongest band is found at 836 cm⁻¹ in the I glass spectrum. Through comparison with the previous Raman data of other titania silicate glasses, we conclude that the Ba₂TiSi₂O₈ glass has a structure similar to the crystalline phase.     

Preparation of Transparent Conductive (ZnO)mIn2O3 Fine Powder by Gel-Combustion Reaction

A fine powder of (ZnO) _m In₂O₃ ( m =3, 4) was obtained by the self-combustion reaction, under firing at a furnace temperature of 350°C in a nitrogen atmosphere, of a gel prepared from a mixed zinc and indium nitrate aqueous solution peptized with citric acid. A (ZnO)₃In₂O₃ single-phase product was obtained when citric acid was substituted by glycine, because the combustion temperature of glycine mixture is >1260°C. The highest electrical conductivity, 0.2 S cm⁻¹, was obtained in a tin-substituted, transparent conducting (ZnO) _m In₂O₃ product, where m =3 and 4.     

Reaction of Cyanogen with SiO2 Surfaces

Infrared spectra (4000 to 1300 cm⁻¹) of SiO₂ specimens with high surface areas which had been exposed to (CN)₂ at 25° to 600°C were recorded. Sorption was slight at 25°, but extensive reaction occurred at higher temperatures. The main effects of the sorption were the decrease of the 3747 cm⁻¹ band of surface Si-OH groups and the buildup of a prominent band at 2310 cm⁻¹ thought to be caused by surface Si-NCO species rather than Si-OCN species. The data suggest that, in addition to the isocyanate formed in the dehydroxylation reaction, HCN produced in that reaction led to the formation of Si-CN and Si-OH     

Single-Calcination Synthesis of Pyrochlore-Free 0.9Pb(Mg1/3Nb2/3)O3–0.1PbTiO3 and Pb(Mg1/3Nb2/3)O3 Ceramics Using a Coating Method

A coating approach for synthesizing 0.9Pb(Mg_1/3Nb_2/3)O₃–0.1PbTiO₃ (0.9PMN–0.1PT) and PMN using a single calcination step was demonstrated. The pyrochlore phase was prevented by coating Mg(OH)₂ on Nb₂O₅ particles. Coating of Mg(OH)₂ on Nb₂O₅ was done by precipitating Mg(OH)₂ in an aqueous Nb₂O₅ suspension at pH 10. The coating was confirmed using optical micrographs and zeta-potential measurements. A single calcination treatment of the Mg(OH)₂-coated Nb₂O₅ particles mixed with appropriate amounts of PbO and PbTiO₃ powders at 900°C for 2 h produced pyrochlore-free perovskite 0.9PMN–0.1PT and PMN powders. The elimination of the pyrochlore phase was attributed to the separation of PbO and Nb₂O₅ by the Mg(OH)₂ coating. The Mg(OH)₂ coating on the Nb₂O₅ improved the mixing of Mg(OH)₂ and Nb₂O₅ and decreased the temperature for complete columbite conversion to ∼850°C. The pyrochlore-free perovskite 0.9PMN–0.1PT powders were sintered to 97% density at 1150°C. The sintered 0.9PMN–0.1PT ceramics exhibited a dielectric constant maximum of ∼24 660 at 45°C at a frequency of 1 kHz.     

Phase Relations and Ordering in the Systems MgO-Y2O3-ZrO2 and CaO-MgO-ZrO2

The phase relations in the systems MgO-Y₂O₃-ZrO₂ and CaO-MgO-ZrO₂ were established at 1220° and 1420°C. The system MgO-Y₂O₃-ZrO₂ possesses a much-larger cubic ZrO₂ solid solution phase field than the system CaO-MgO-ZrO₂ at both temperatures. The ordered δ phase (Zr₃Y₄O₁₂) was found to be stable in the system ZrO₂-Y₂O₃ at 1220°C. Two ordered phases φ₁ (CaZr₄O₉) and φ₂ (Ca₆Zr₁₉O₄₄) were stable at 1220°C in the system ZrO₂-CaO. At 1420°C no ordered phase appears in either system, in agreement with the previously determined temperature limits of the stability for the δ, φ₁, and φ₂ phases. The existence of the compound Mg₃Y_zO₆ could not be confirmed.     

Spark Plasma Sintering of LiTi2(PO4)3-Based Solid Electrolytes

Solid electrolytes, LiTi₂(PO₄)₃ (LTP), Li_1.3Al_0.3Ti_1.7(PO₄)₃ (LATP), and Li_1.3Al_0.3Ti_1.7(PO₄)_2.9(VO₄)_0.1 (LATPV), were prepared by conventional sintering (CS) and spark plasma sintering (SPS) methods, and the Li⁺ ion conductivity of the sintered pellets was examined using an impedance analyzer. SPS remarkably improved the densification compared to CS and resulted in dense ceramics (95–97% of theoretical density) irrespective of the substituted ions. The highest conductivity of 2.6 × 10⁻⁴ S/cm was found for the LATPV specimen sintered by spark plasma at 1100°C. LATP and LATPV exhibited an order of magnitude higher ionic conductivity than LTP in the specimens of similar densities. The results demonstrated that the enhanced conductivity in substituted LTP is not due to the enhanced densification alone. The other possible explanations are discussed in terms of bottleneck size, lithium content, and grain boundary characteristics.     

Probing of 1:2 Ordering in Ba(Ni1/3Nb2/3)O3 and Ba(Zn1/3Nb2/3)O3 Ceramics by XRD and Raman Spectroscopy

The 1:2 ordering in Ba(Ni_1/3Nb_2/3)O ceramics sintered at 1350-1500°C has been investigated by using XRD and Raman spectroscopy. Both of the techniques show that the degree of the 1:2 ordering decreases as the sintering temperature increases. However, XRD discerns the 1:2 ordering only for the samples sintered at 1350-1400°C, whereas Raman spectroscopy discerns the 1:2 ordering for all the samples. Similar results have been obtained for Ba(Zn_1/3Nb_2/3)O₃ ceramics, where only the temperature range is slightly different. It is demonstrated that Raman spectroscopy can be a useful tool for probing of the 1:2 ordering in the A(B'^II_1/3B"^V_2/3)O₃-type complex perovskite compounds.     

Formation and Structural Characterization of 1:1 Ordered Perovskites in the Ba(Zn1/3Ta2/3)O3–BaZrO3 System

The phase stabilities in the(1−x)Ba(Zn_1/3Ta_2/3)O₃ (BZT)-xBaZrO₃(BZ)system have been investigated using samples prepared by the mixed oxide method. The substitution of Zr⁴⁺destabilizes the 1:2 cation ordering in BZT and pro-motes the formation of a cubic, 1:1 ordered structure with a doubled perovskite repeat. The homogeneity range of the 1:1 phase extends from x = 0.04 to approximately x = 0.25; substitutions beyond this range stabilize a disordered perovskite. The limits of stability of the 1:1 ordering coin-cide with compositions previously found to exhibit anoma-lies in their dielectric loss. The range of homogeneity is consistent with a "random layer" model for the 1:1 ordered "Ba{β';_1/2β^1/2}O₃" structure. In this model the B× positions are assumed to be occupied exclusively by Ta⁵⁺, and the b× sites by a random distribution of Zn₂₊, Zr₄₊, and the remaining Ta 5+ cations. The validity of the model, where the ordered solid solutions can be represented by Ba{[Zn_{2− y /3}Ta_{(1−2 y )/3}Zr y ]_1/2[Ta]_1/2}O₃(y =2x)was con-firmed by Rietveld refinements conducted using data col-lected with a synchrotron X-ray source.     

New Preparation Method of Low-Temperature-Sinterable Perovskite 0.9Pb(Mg1/3Nb2/3)O3-0.1PbTiO3 Powder and Its Dielectric Properties

A relaxor ferroelectric material, 0.9Pb(Mg_1/3Nb_2/3)O₃-0.1PbTiO₃ (0.9PMN-0.1PT) with a pyrochlore-free phase, was prepared by using one-step calcination in the present study. The 0.9PMN-0.1PT powder with the pure perovskite phase was prepared successfully from a mixture of the PMN precursor and the crystalline PT by heating for 2 h at temperatures greaterthan equal to750°C. The PMN precursor was synthesized by adding an aqueous Mg(NO₃)₂ solution, rather than MgO, to the alcoholic slurry of PbO and Nb₂O₅. The 0.9PMN-0.1PT powder sintered to >96% relative density via heat treatment for 2 h at temperatures of 900°-1200°C. The highest room-temperature dielectric constant (epsilon_rt) was 24700 at 1 kHz for the samples that were sintered at 1100°C; however, the samples that were sintered at 900°C still had epsilon_rt values of 22600 at 1 kHz.     

Phase Diagram of the System BaO-Fe2O3

The phase diagram of the system BaO-Fe₂0₃ was determined by X-ray diffraction, melting-point measurement, and microscopic methods. Since the reduction of Fe³⁺ to Fe²⁺ was observed by chemical analysis in the samples heated at high temperature, especially in molten samples, the samples were heated at 1 atmosphere pressure of oxygen in the temperature region in which the liquid was in equilibrium; 1 atmosphere pressure of oxygen was su5cient to restrain the reduction of Fe³⁺. In the temperature region of solid-solid equilibrium, the dissociation was not observed even when the samples were heated in air. BaO - 6Fe₂O₃ formed a solid solution with BaO.Fe₂0₃. The BaO:Fe₂0₃ ratio of the solid solution was BaO.4.5Fe₂0₃ at 1350°C. and BaO. 5.0Fe₂0_a at 800°C. The precipitation micro-structures of each primary solid solution were observed.