Effect of welding speed on microstructures and mechanical properties of underwater friction stir welded 2219 aluminum alloy

Underwater friction stir welding (underwater FSW) has been demonstrated to be available for the strength improvement of normal FSW joints. In the present study, a 2219 aluminum alloy was underwater friction stir welded at a fixed rotation speed of 800 rpm and various welding speeds ranging from 50 to 200 mm/min in order to clarify the effect of welding speed on the performance of underwater friction stir welded joint. The results revealed that the precipitate deterioration in the thermal mechanically affected zone and the heat affected zone is weakened with the increase of welding speed, leading to a narrowing of softening region and an increase in lowest hardness value. Tensile strength firstly increases with the welding speed but dramatically decreases at the welding speed of 200 mm/min owing to the occurrence of groove defect. During tensile test, the joint welded at a lower welding speed is fractured in the heat affected zone on the retreating side. While at higher welding speed, the defect-free joint is fractured in the thermal mechanically affected zone on the advancing side.     

2A12铝合金筋板件T型搅拌摩擦焊工艺及焊后热处理

为评价2A12铝合金筋板件搅拌摩擦焊工艺并探寻提高接头强度的途径,进行了2A12铝合金筋板件的T型搅拌摩擦焊焊接工艺试验,并对不同人工时效热处理下焊接接头的微观组织及性能进行了研究.研究表明:采用T型搅拌摩擦焊即可实现2A12铝合金筋板件的成形,当搅拌头旋转速度为750 r/min、焊接速度60mm/min时,接头的抗...     

Effect of welding parameters on microstructure and mechanical properties of friction stir welded joints of AA7039 aluminum alloy

A high strength Al–Zn–Mg alloy AA7039 was friction stir welded by varying welding and rotary speed of the tool in order to investigate the effect of varying welding parameters on microstructure and mechanical properties. The friction stir welding (FSW) process parameters have great influence on heat input per unit length of weld, hence on temperature profile which in turn governs the microstructure and mechanical properties of welded joints. There exits an optimum combination of welding and rotary speed to produce a sound and defect free joint with microstructure that yields maximum mechanical properties. The mechanical properties increase with decreasing welding speed/ increasing rotary speed i.e. with increasing heat input per unit length of welded joint. The high heat input joints fractured from heat affected zone (HAZ) adjacent to thermo-mechanically affected zone (TMAZ) on advancing side while low heat input joints fractured from weld nugget along zigzag line on advancing side.     

Defect features and mechanical properties of friction stir lap welded dissimilar AA2024–AA7075 aluminum alloy sheets

5 mm-Thick dissimilar AA2024-T3 and AA7075-T6 aluminum alloy sheets were friction stir lap welded in two joint combinations, i.e., (top) 2024/7075 (bottom) and 7075/2024. The influences of process conditions (welding speed and joint combination) on defects (hook and voids) features and mechanical properties of joints were investigated in detail. It was found that the hook deflects largely upwards into the stir zone (SZ) at lower welding speeds (50, 150 mm/min) in both combinations. The process conditions significantly affect the hook geometry which in return affects the lap shear strength. In all 2024/7075 joints, voids appear and the joints fracture from the tip of hook on AS along the SZ/TMAZ (thermomechanically affected zone) interface in lap shear test (tensile fracture mode). In 7075/2024 joints, the hook on RS horizontally extends a large distance into the bottom stir zone at higher welding speeds (225, 300 mm/min). The joints fracture in three modes: shear fracture along the lap interfaces, tensile fracture and the mix fracture of both. In both joint combinations, the lap shear strength generally increases with the increase of welding speed. 7075/2024 Joints show higher failure load than 2024/7075 joints at lower welding speeds while the opposite result appears at higher welding speeds.     

Effect of weld curvature radius and tool rotation direction on joint microstructure in friction stir welding casting alloys

Curved welds were designed and the effects of the weld curvature radius and tool rotation direction on the microstructure of friction stir welded cast aluminum alloy joints were investigated. Results show that both the weld curvature radius and tool rotation direction have a significant influence on the microstructure of the curved joints during FSW. With decreasing weld curvature radius, the size of the tunnel defect is reduces and the proportion of fine Si particles in the stir zone increases. Si particles are finer and denser in the retreating side (RS) than that in the advancing side (AS) when both the welding direction and tool rotation direction are anticlockwise. However, when the welding direction is anticlockwise while the tool rotates clockwise, the proportions of fine Si particles decrease compared to the former situation. Furthermore, the tunnel defect is more likely to be present in the AS in the former situation.     

The microstructure and mechanical properties of friction stir welded Al–Zn–Mg alloy in as welded and heat treated conditions

High strength aluminium alloys generally present low weldability because of the poor solidification microstructure, porosity in the fusion zone and loss in mechanical properties when welded by fusion welding processes which otherwise can be welded successfully by comparatively newly developed process called friction stir welding (FSW). This paper presents the effect of post weld heat treatment (T₆) on the microstructure and mechanical properties of friction stir welded 7039 aluminium alloy. It was observed that the thermo-mechanically affected zone (TMAZ) showed coarser grains than that of nugget zone but lower than that of heat affected zone (HAZ). The decrease in yield strength of welds is more serious than decrease in ultimate tensile strength. As welded joint has highest joint efficiency (92.1%). Post weld heat treatment lowers yield strength, ultimate tensile strength but improves percentage elongation.     

焊接速度对 7A52 铝合金 FSW 组织及力学性能的影响

目的在保证搅拌速度一定时,针对8 mm厚的7A52铝合金,在不同焊接速度下采用搅拌摩擦焊(FSW)进行焊接试验,研究其焊接接头的显微组织及力学性能。方法利用搅拌摩擦焊机进行对接焊接,焊后制取金相试样观察焊接接头宏观形貌和显微组织,并测定其力学性能。结果7A52铝合金FSW焊接接头焊核区的面积随着焊接速度的增大而增大,当焊接速度为250mm/min时,焊接接头的焊核区面积最大,焊核区的显微组织都为细小的等轴晶,焊接接头横截面的焊核区呈明显"洋葱环"的形貌,而热力影响区的结构特征则呈现出了较高的塑性变形流线层。焊接接头显微硬度分布都呈现出"W"形变化,在焊接速度为150 mm/min时,焊接接头的平均抗拉强度能达到452 MPa,达到了母材抗拉强度的89%。结论通过对不同焊接速度下7A52铝合金FSW焊接接头的组织和性能进行研究,得到了不同焊接速度下焊接接头组织和力学性能。     

Joint properties of dissimilar Al6061-T6 aluminum alloy/Ti–6%Al–4%V titanium alloy by gas tungsten arc welding assisted hybrid friction stir welding

Hybrid friction stir butt welding of Al6061-T6 aluminum alloy plate to Ti–6%Al–4%V titanium alloy plate with satisfactory acceptable joint strength was successfully achieved using preceding gas tungsten arc welding (GTAW) preheating heat source of the Ti alloy plate surface. Hybrid friction stir welding (HFSW) joints were welded completely without any unwelded zone resulting from smooth material flow by equally distributed temperature both in Al alloy side and Ti alloy side using GTAW assistance for preheating the Ti alloy plate unlike friction stir welding (FSW) joints. The ultimate tensile strength was approximately 91% in HFSW welds by that of the Al alloy base metal, which was 24% higher than that of FSW welds without GTAW under same welding condition. Notably, it was found that elongation in HFSW welds increased significantly compared with that of FSW welds, which resulted in improved joint strength. The ductile fracture was the main fracture mode in tensile test of HFSW welds.     

压铸态AZ91D镁合金搅拌摩擦焊接头微观组织研究

采用搅拌摩擦焊工艺对4mm厚的压铸态AZ91D镁合金进行对接工艺实验,搅拌头旋转速率1500r/min,焊接速率120mm/min;使用光学显微镜和扫描电镜对焊接接头微观组织进行了研究。结果表明:焊缝外观成形美观,但内部存在贯穿型隧道状孔洞缺陷;焊核区为典型的变形-再结晶组织,为细小、均匀的等轴晶;机械-热影响区为变形-部分再结晶组织,热影响区组织形貌与母材相近但伴有轻微的长大现象;焊核区与机械-热影响区的过渡具有以下特征:在前进侧呈现"突变"特征,在后退侧呈现"渐变"特征。     

Effect of friction stir welding parameters on microstructural characteristics and mechanical properties of 2219-T6 aluminum alloy joints

A 2219-T6 aluminum alloy was friction stir welded in the present study. The results indicate that the recrystallized grains in the weld nugget zone (WNZ) of the joints exhibit the largest size in the middle part and the smallest size in the lower part. Furthermore, the void defect is formed in the joint when the rotation speed or welding speed is quite high. As the rotation speed or welding speed increases, the tensile strength of the joint firstly increases to a maximum value and then sharply decreases due to the occurrence of void defect. During tensile test, the defect-free joints welded at lower rotation speed are fractured in the WNZ, while those welded at relatively high rotation speed tend to be fractured in the heat affected zone (HAZ) adjacent to the thermal mechanically affected zone (TMAZ) on the retreating side.     

Microstructure and mechanical properties of spray formed 7055 aluminum alloy by underwater friction stir welding

Ultra-high strength spray formed 7055 aluminum alloy in which Zn is supersaturated solid solution requires strict control of heat input in welding process. In this paper, underwater friction stir welding is carried out in order to reduce heat input comparing with traditional friction stir welding and further improve the joint performances by varying welding temperature history. Through comparing the thermal cycle curves and distribution of residual stress of the plate welded in different media, the reason why the joint welded underwater shows a better performance is figured out. The result shows that tensile strength, hardness and plasticity of underwater welded joint are better than that welded in air. The underwater joint has a fine grained microstructure without “S line” defect, a typically distinct boundary between the weld nugget zone and the thermal mechanically affected zone and a narrow heat affected zone. The main strengthening phase in underwater joint is MgZn₂ .     

Formation and mechanical properties of stationary shoulder friction stir welded 6005A-T6 aluminum alloy

6005A-T6 aluminum alloy is welded by stationary shoulder friction stir welding (SSFSW). At a constant rotational velocity of 2000 rpm, the effect of welding speed on mechanical properties of SSFSW joint are investigated in detail. Defect-free joint with gloss surface and small flash is attained and no cracks appear at the bending angle of 180°. Compared with traditional friction stir welding (FSW), width of rotational shoulder affected zone is relatively small because of the smaller diameter of rotational shoulder. Increasing welding speed is benefit for reducing the width of softening region and the softening degree. The fracture position of welding joint locates in thermo-mechanically affected zone and the fracture surface morphology presents the typical ductile fracture. The maximum tensile strength of joint at the welding speed of 400 mm/min reaches 82% of base metal (BM).     

AZ31镁合金搅拌摩擦焊接头断裂机制

对AZ31镁合金搅拌摩擦焊接头进行力学性能实验.拉伸、疲劳实验结果显示,AZ31镁合金搅拌摩擦焊接头抗拉强度可以达到母材强度的92.9%,断裂位置在前进面的机械热影响区,认为是前进面机械热影响区不均匀的层状组织和应力集中作用的结果.扫描电镜显示:断口有明显的撕裂纹和纤维状组织.     

铝合金超声辅助搅拌摩擦焊接接头组织性能研究

目的探究超声振动对铝合金搅拌摩擦焊的作用效果。方法分别采用普通搅拌摩擦焊和超声辅助搅拌摩擦焊方法,对7075铝合金进行焊接试验,并对焊接接头的微观组织、力学性能、断口形貌进行分析。结果普通搅拌摩擦焊焊缝中生成了隧道型缺陷,施加超声振动后,缺陷消失,形成了无缺陷的良好接头,且与普通搅拌摩擦焊相比,超声辅助搅拌摩擦焊焊缝热影响区晶粒长大程度较小,焊核晶粒细化。接头强度明显提高,达到铝合金母材强度的71.5%,接头断裂模式为韧窝和准解理的混合断裂形式。结论超声振动促进了塑性金属的流动,能有效抑制孔洞、隧道型缺陷等的形成,同时超声振动能在提升金属塑性的同时,降低焊缝的热输入。     

7075铝合金高速搅拌摩擦焊材料流动行为及性能研究

目的 针对7075–O铝合金高焊速、高转速搅拌摩擦焊接缺陷多、质量差等问题,研究焊接接头材料流动对焊缝性能的影响。方法 选用焊接速度1 000 mm/min,搅拌转速分别为1 000、1 200、1 600、1 700 r/min的条件对7075–O铝合金板进行搅拌摩擦焊接,分析不同焊接工艺参数下焊接接头的显微组织及力学性能。同时,利用Fluent软件模拟7075–O铝合金搅拌摩擦焊接过程中的材料流动场分布,分析焊接材料流动与缺陷形成的关系。结果 利用7075–O铝合金三维流动模型,预测出高焊速条件下焊缝前进侧形成一个低压区,孔洞等缺陷易出现在此区域,数值模拟预测与试验结果吻合。在高焊接速度1 000 mm/min、焊接转速1 200 r/min时,焊缝表面光滑平整,焊核区域的硬度分布更加均匀。结论 随着搅拌转速从1 000 r/min增大到1 700 r/min,热输入量逐渐增大,孔洞缺陷由隧道型孔洞转变为不连续的小孔。同时,随着搅拌转速的增大,焊缝高硬度区域的宽度先增大而后降低。当搅拌转速为1 200 r/min时得到了优质的焊接接头,焊缝焊核区硬度分布均匀,硬度值最高为176HV。     

水下搅拌摩擦焊对铝/铜接头组织与性能的影响

目的 采用搅拌摩擦焊,对比分析大气环境和水下环境下铝/铜接头的组织与性能,以期获得力学性能更优异的铝/铜焊接接头。方法 利用搅拌摩擦焊,在焊接速度为40 mm/min、旋转速度为1 000 r/min的条件下,分别在大气环境和水下环境下对厚度为9 mm的6061铝合金板和T2纯铜板进行焊接。然后,对铝/铜界面、焊核区进行扫描电镜及能谱分析,并对铝/铜界面及焊核区进行物相分析,确定产物相组成。最后,对铝/铜试样进行拉伸及硬度检测。结果 铝/铜接头均无裂纹、气孔等缺陷。铜颗粒弥散分布在焊核区,铝/铜界面形成金属间化合物层。水下搅拌摩擦焊下界面元素扩散距离明显变短,且金属间化合物厚度更薄。铝/铜接头的金属间化合物为AlCu和Al4Cu9。大气环境焊接下接头的抗拉强度为130.6 MPa,断裂方式为脆性断裂;水下焊接下接头的抗拉强度为199.5 MPa,断裂方式为韧性断裂。水下环境下的接头硬度值更高,其中热影响区的硬度最低值约为65HV。结论 水下搅拌摩擦焊铝/铜接头无裂纹、气孔等缺陷。组织上,水下搅拌摩擦焊的铝/铜接头界面元素扩散距离更短,硬脆的金属间化合物更少;性能上,水下搅拌摩擦焊的铝/铜接头强度更高,抗拉强度达到199.5 MPa,达到母材的74.4%。     

Evaluation of the microstructure and mechanical properties of friction stir welded 6005 aluminum alloy

Abstract

The microstructural change related with the hardness profile has been evaluated for friction stir welded, age hardenable 6005 Al alloy. Frictional heat and plastic flow during friction stir welding created fine and equiaxed grains in the stir zone (SZ), and elongated and recovered grains in the thermomechanically affected zone (TMAZ). The heat affected zone (HAZ), identified only by the hardness result because there is no difference in grain structure compared to the base metal, was formed beside the weld zone. A softened region was formed near the weld zone during the friction stir welding process. The softened region was characterised by the dissolution and coarsening of the strengthening precipitate during friction stir welding. Sound joints in 6005 Al alloys were successfully formed under a wide range of friction stir welding conditions. The maximum tensile strength, obtained at 507 mm min^-1 welding speed and 1600 rev min^-1 tool rotation speed, was 220 MPa, which was 85% of the strength of the base metal.     

Evaluation of microstructures and mechanical properties of friction stir welded lap joints of Inconel 600/SS 400

The microstructures and mechanical properties of friction stir welded Inconel 600 and SS 400 lap joints were evaluated in this study. Friction stir welding was carried out at a tool rotation speed of 200 rpm and a welding speed of 100 mm/min. Application of friction stir welding was notably effective in reducing the grain size of the stir zone, as a result, the average grain size of Inconel 600 was reduced from 20 μm in the base material to 8.5 μm in the stir zone. The joint interface between Inconel 600 and SS 400 was soundly welded without voids and cracks, and MC carbides with a size of 50 nm were partially formed in the region of the lap joint interface in Inconel 600. In addition, a hook from SS 400 was formed on the advancing side of the Inconel 600 alloy, which directly affected an increase in the peel strength of the weld. In this study, we systematically discussed the effect of friction stir welding on the evolution of the microstructures and mechanical properties of friction stir lap jointed Inconel 600 and SS 400.     

6005A-T6铝合金搅拌摩擦焊接头组织与力学性能特征

采用光学显微镜、扫描电子显微镜、透射电子显微镜、拉伸实验机和显微硬度计对6005A铝合金搅拌摩擦焊接头的微观组织及力学性能进行了研究。结果表明:焊核区为细小的等轴晶,几乎所有粒子溶于基体;热机械影响区呈现为被拉长的畸变晶粒,且存在大量的位错;热影响区的组织明显粗化,处于过时效状态。与母材相比,搅拌摩擦焊接头的强度及伸长率均有下降趋势,且接头出现软化,最小硬度值出现在前进侧的热影响区内。搅拌头旋转速率为1200r/min、焊接速率为200mm/min时可获得优质接头,抗拉强度达到母材强度的72%,伸长率达到母材的69%。     

Experimental and numerical investigations of bonding interface behavior in stationary shoulder friction stir lap welding

Stationary shoulder friction stir lap welding (SSFSLW) was employed to weld 2024 aluminum alloy. A coupled Eulerian-Lagrangian (CEL) model was developed to investigate the lap interface behavior during SSFSLW. Numerical results of material movement and equivalent plastic strain were in good agreement with the experimental work. With increasing welding speed, the distances from the hook tip to the top surface of the upper workpiece on the retreating side (RS) and the advancing side (AS) increase, while the distance between two wave-shaped alclads decreases. A symmetric interface bending is observed on the AS and the RS during plunging, while the interface bending on the AS is bigger than that on the RS during welding. The peak temperature of the interface on the AS is higher than that on the RS. The equivalent plastic strain gradually increases as the distance to the weld center decreases, and its peak value is obtained near the bottom of the weld.