Residual stress influence on fatigue lifetimes of electroplated AISI 4340 high strength steel

Residual stresses play an important role in the fatigue lives of structural engineering components. In the case of near surface tensile residual stresses, the initiation and propagation phases of fatigue process are accelerated; on the other hand, compressive residual stresses close to the surface may increase fatigue life. In both decorative and functional applications, chromium electroplating results in excellent wear and corrosion resistance. However, it is well known that it reduces the fatigue strength of a component. This is due to high tensile internal stresses and microcrack density. Efforts to improve hard chromium properties have increased in recent years. In this study, the effect of a nickel layer sulphamate process, as simple layer and interlayer, on fatigue strength of hard chromium electroplated AISI 4340 steel hardness – HRc 53, was analysed. The analysis was performed by rotating bending fatigue tests on AISI 4340 steel specimens with the following experimental groups: base material, hard chromium electroplated, sulphamate nickel electroplated, sulphamate nickel interlayer on hard chromium electroplated and electroless nickel interlayer on hard chromium electroplated. Results showed a decrease in fatigue strength in coated specimens and that both nickel plating interlayers were responsible for the increase in fatigue life of AISI 4340 chromium electroplated steel. The shot peening pre-treatment was efficient in reducing fatigue loss in the alternatives studied.     

On the influence of rubbing fracture surfaces on fatigue crack propagation in mode III

Fatigue crack growth has been studied under fully reversed torsional loading (R = ?1) using AISI 4340 steel, quenched and tempered at 200°, 400° and 650°C. Only at high stress intensity ranges and short crack lengths are all specimens characterized by a microscopically flat Mode III (anti-plane shear) fracture surface. At lower stress intensities and larger crack lengths, fracture surfaces show a local hill-and-valley morphology with Mode I, 45° branch cracks. Since such surfaces are in sliding contact, friction, abrasion and mutual support of parts of the surface can occur readily during Mode III crack advance. Without significant axial loads superimposed on the torsional loading to minimize this interference, Mode III crack growth rates cannot be uniquely characterized by driving force parameters, such as ΔK_III and ΔCTD_III, computed from applied loads and crack length values. However, for short crack lengths (?0.4 mm), where such crack surface interference is minimal in this steel, it is found that the crack growth rate per cycle in Mode III is only a factor of four smaller than equivalent behaviour in Mode I, for the 650°C temper at $\text{ΔK}{}_{\mathrm{III}}\text{= 45 MPa m}\text{1}\text{2}$.     

Influence of residual stresses from shot peening on fretting fatigue crack growth

One method to improve fretting fatigue life is to shot peen the contact surfaces. Experimental fretting life results from specimens in a Titanium alloy with and without shot peened surfaces were evaluated numerically. The residual stresses were measured at different depths below the fretting scar and compared to the corresponding residual stress profile of an unfretted surface. Thus, the amount of stress relaxation during fretting tests was estimated. Elastic–plastic finite element computations showed that stress relaxation was locally more significant than that captured in the measurements. Three different numerical fatigue crack growth models were compared. The best agreement between experimental and numerical fatigue lives for both peened and unpeened specimens was achieved with a parametric fatigue growth procedure that took into consideration the growth behaviour along the whole front of a semi‐elliptical surface crack. Furthermore, the improved fretting fatigue life from shot peening was explained by slower crack growth rates in the shallow surface layer with compressive residual stresses from shot peening. The successful life analyses hinged on three important issues: an accurate residual stress profile, a sufficiently small start crack and a valid crack growth model.     

The effect of residual stresses arising from laser shock peening on fatigue crack growth

Residual stresses have in the past been introduced to manipulate growth rates and shapes of cracks under cyclic loads. Previously, the effectiveness of shot peening in retarding the rate of fatigue crack growth was experimentally studied. It was shown that the compressive residual stresses arising from the shot peening process can affect the rate of crack growth. Laser shock peening can produce a deeper compressive stress field near the surface than shot peening. This advantage makes this technique desirable for the manipulation of crack growth rates. This paper describes an experimental program that was carried out to establish this effect in which steel specimens were partially laser peened and subsequently subjected to cyclic loading to grow fatigue cracks. The residual stress fields generated by the laser shock peening process were measured using the neutron diffraction technique. A state of compressive stress was found near the surface and tensile stresses were measured in the mid-thickness of the specimens. Growth rates of the cracks were observed to be more affected by the tensile core than by the compressive surface stresses.     

Overload effect on the fatigue crack propagation in large‐scale tubular joints

This paper examines the overloading effect on the fatigue crack propagations monitored in a large‐scale tubular X‐joint specimen under two separate cyclic tests. The first cyclic test applies a constant‐amplitude brace in‐plane bending to the joint, with a single cycle of 150% overload before the crack depth reaches the mid‐thickness of the chord. The second fatigue test applies two batches of cyclic loads, with the amplitude of the second batch at 66% of the former. The X‐joint specimen experiences a 150% overload cycle during the first batch of loading, followed by the second batch after it has recovered from the overload effect. The experimental results reveal that deep surface cracks experience more significant overload retardation than does a shallow fatigue crack. The Paris law estimation indicates that the single overload cycle applied in the first specimen leads to a 7% increase in the fatigue life of the X‐joint.     

Fatigue crack propagation under in‐phase and out‐of‐phase biaxial loading

Fatigue damage characteristics of aluminium alloy under complex biaxial loads such as in‐phase and out‐of‐phase loading conditions and different biaxiality ratios have been investigated. The effects of microscale phenomena on macroscale crack growth were studied to develop an in‐depth understanding of crack nucleation and growth. Material characterization was conducted to study the microstructure variability. Scanning electron microscopy was used to identify the second phase particles, and energy dispersive X‐ray spectroscopy was performed to analyse their phases and elements. Extensive quasi‐static and fatigue tests were conducted on Al7075‐T651 cruciform specimens over a wide range of load ratios and phases. Detailed fractography analysis was conducted to understand the crack growth behaviour observed during the fatigue tests. Significant differences in crack initiation and propagation behaviour were observed when a phase difference was applied. Primarily, crack retardation and splitting were observed because of the constantly varying mode mixity caused by phase difference. The crack growth behaviour and fatigue lives under out‐of‐phase loading were compared with those under in‐phase loading to understand the effect of mixed‐mode fracture.     

The influence of partial surface shot peening on fatigue crack growth behaviour of a high‐strength ferritic steel

The effects of partial surface shot peening on the fatigue crack growth behaviour of a ferritic steel have been experimentally investigated in this paper. Dog‐bone specimens fabricated from Optim700QL were tested under tension‐tension fatigue loads. Three distinct extents of partial shot peening, with respect to the crack tip and specimen symmetry line, were tested. The fatigue crack growth results from these experiments have been compared with those obtained from the same specimen geometry but with no peening. The results show that the residual stress fields formed ahead of the initial notch tip due to the partial peening process play a significant role in the fatigue crack growth behaviour of the material and effectively result in accelerated crack propagation at the midwidth of the specimens. It has been shown in this study that partial peening can lead to a fatigue crack growth rate around twice as fast as that of the unpeened specimen.     

Experimental fatigue crack growth analysis and modelling in part‐through circumferentially pre‐cracked pipes under pure bending load

In the present work, an attempt has been made to study the fatigue crack growth in a part‐through circumferentially notched pipe specimen. It has been observed that under four‐point bend cyclic load, the crack propagates in a transverse plane in the radial direction initially followed by propagation in the circumferential direction. The crack extension in the circumferential direction resulted crack growth retardation in the radial direction. This behaviour of the fatigue crack growth has been modelled, and a fatigue life prediction methodology based on an exponential model has been applied for prediction of fatigue crack growth.     

Local strain accumulation in fatigue crack propagation process of Ti‐6Al‐4V alloy

Fatigue crack growth behaviours of the titanium alloy Ti‐6Al‐4V, with two different microstructures, at different maximum stresses were identified by digital image correlation technique. Full‐field strains were monitored around fatigue cracks after consecutive cycles in fatigue crack growth experiments. Results indicated that the Ti‐6Al‐4V alloy with a bi‐modal microstructure had a better fatigue resistance than that with a primary‐α microstructure. Typical behaviours of small cracks and the evolution of multi‐scale fatigue cracks were clarified. The strain accumulations around the micro‐notch and fatigue crack increased with increasing number of load cycles. On the basis of von Mises strain mapping, it was found that crack growth rate could be characterized by crack‐tip plastic zone size.     

A local multigrid X‐FEM strategy for 3‐D crack propagation

A multiscale method for 3‐D crack propagation simulation in large structures is proposed. The method is based on the extended finite element method (X‐FEM). The asymptotic behavior of the crack front is accurately modeled using enriched elements and no remeshing is required during crack propagation. However, the different scales involved in fracture mechanics problems can differ by several orders of magnitude and industrial meshes are usually not designed to account for small cracks. Enrichments are therefore useless if the crack is too small compared with the element size. To overcome this drawback, a project combining different numerical techniques was started. The first step was the implementation of a global multigrid algorithm within the X‐FEM framework and was presented in a previous paper (Eur. J. Comput. Mech. 2007; 16 :161–182). This work emphasized the high efficiency in cpu time but highlighted that mesh refinement is required on localized areas only (cracks, inclusions, steep gradient zones). This paper aims at linking the different scales by using a local multigrid approach. The coupling of this technique with the X‐FEM is described and computational aspects dealing with intergrid operators, optimal multiscale enrichment strategy and level sets are pointed out. Examples illustrating the accuracy and efficiency of the method are given. Copyright © 2008 John Wiley & Sons, Ltd.     

Nonlinear fatigue crack propagation in a baffle module of Wendelstein 7‐X under cyclic bending loads

Simulation of the fatigue crack propagation in a Wendelstein 7‐X baffle module is performed in this study using both a finite element method‐based software and the UniGrow nonlinear model for small‐scale yielding (SSY) conditions. Some experimental fatigue tests of several cracked baffle modules have been performed through a servo‐hydraulic machine. One of these experimental tests has been considered to simulate fatigue crack propagation in the baffle module. Before starting the experimental test, a first crack partly contained in the welding seam and partly in the steel pipe is found. Subsequently, owing to the applied load, the crack propagated both into the welding seam and into the steel pipe until the plastic zone in the near field attains SSY conditions. Finally, owing to the increase in the extension of the plastic zone, SSY conditions are not more valid, and the breakage of the steel pipe is produced by plastic collapse.     

Crack closure in friction stir weldment using non‐linear model for fatigue crack propagation

The fatigue crack propagation in a friction stir‐welded sample has been simulated herein by means of two 3‐dimensional finite element method (FEM)‐based analyses. Numerical simulations of the fatigue crack propagation have been carried out by assuming a residual stress field as a starting condition. Two initial cracks, observed in the real specimen, have been assessed experimentally by performing fatigue tests on the welded sample. Hence, the same cracks have been placed in the corresponding FE model, and then a remote load with boundary conditions has been applied on the welded specimen. The material behaviour of the welded joint has been modelled by means of the Ramberg‐Osgood equation, while the non‐linear Kujawski‐Ellyin (KE) model has been adopted for the fatigue crack propagation under small‐scale yielding (SSY) conditions. Owing to the compressive nature of the residual stress field that acts on a part of the cracked regions, the crack closure phenomenon has also been considered. Then, the original version of the KE law has been modified to fully include the closure effect in the analysis. Later, the crack closure effect has also been assessed in the simulation of fatigue propagation of three cracks. Finally, an investigation of the fracture process zone (FPZ) extension as well as the cyclic plastic zone (CPZ) and monotonic plastic zone (MPZ) extensions have been assessed.     

Effects of Shot‐Peening on Fretting Fatigue Crack Growth Behavior in Ti‐6Al‐4V

Abstract: The effects of shot‐peening on fretting fatigue crack growth behaviour in titanium alloy, Ti‐6A1‐4V were investigated. Three shot‐peening intensities: 4A, 7A and 10A were considered. The analysis involved the fracture mechanics and finite element sub‐modelling technique to estimate crack propagation lives. These computations were supplemented with the experimentally measured total fretting fatigue lives of laboratory specimens to assess the crack initiation lives. Shot‐peening has significant effect on the initiation/propagation phases of fretting fatigue cracks; however this effect depends upon the shot‐peening intensity. The ratio of crack initiation and total life increased while the ratio of the crack propagation and total life decreased with an increase of shot‐peening intensity. Effects of residual compressive stress from shot‐peening on the crack growth behaviour were also investigated. The fretting fatigue crack propagation component of the total life with relaxation increased in comparison to its counterpart without relaxation in each shot‐peened intensity case while the initiation component decreased. Improvement in the fretting fatigue life from the shot‐peening and also with an increase in the shot‐peening intensity appears to be not always due to increase in the crack initiation resistance from shot‐peened induced residual compressive stress.     

Evaluation of temperature‐sensitive fatigue crack propagation of a high‐speed railway wheel rim material

The fatigue crack growth rate (FCGR) of ER8C high‐speed railway wheel rim material was tested at various service temperatures. The temperature sensitivity of fatigue crack propagation was evaluated, and the effect of temperature on the crack propagation mechanism was analyzed. The obtained results indicate a fatigue ductile‐to‐brittle transition (FDBT) point at ?20°C for the ER8C wheel rim materials. A reverse relationship was found between FCGR and temperature for the near threshold and Paris regimes when the temperature was below the FDBT point. However, no evident changing rule was found when the temperature was above this transition point. An evident fatigue crack propagation mode transition was found from lamellar tearing to intergranular cracks, which was related to the FDBT for the near‐threshold regime.     

Fatigue crack propagation characteristics of high‐tensile steel wires for bridge cables

The viability of single edge cracked sheet test method for rapidly determining the crack propagation characteristics of steel wires was investigated. First, fatigue tests under 3 different stress ratios were conducted on the sheet specimens which were manufactured from a kind of widely used cable wires. The test data were analysed, and the crack growth rates of sheet specimens were constructed by Walker model. Then, a series of fatigue tests were performed on notched round‐bar specimens to verify the predictability of Walker model parameters. Moreover, the experimental results obtained in different studies on crack propagation characteristics of steel wires were discussed. The results show that the crack propagation characteristics of sheet specimens behave a certain dependence on depth. The sheet crack growth laws can be well used to predict the fatigue life of notched bar specimens when the mechanical heterogeneity is considered. For bridge cable steels, the rational values for the exponent parameter of Paris law, m, should be close to 3.     

Experimental and analytical investigation of fatigue crack propagation of T‐welded joints considering the effect of boundary condition

T‐welded joints are commonly employed in ship and ocean structures. The fatigue failure of structure components subjected to cyclic loading always occurs in T‐welded joints because of the metallurgical differences, tensile residual stress fields and stress concentrations. The former researches about T‐welded joints fatigue have in common that the boundary condition needs to be taken into account as an influencing parameter to predict the crack propagation during cyclic loading. In this paper, the crack growth behaviour in T‐welded joint processed with Q345D steel (Pingxiang Iron & Steel Co., Ltd, Hukou, Jiangxi Province in China) under the fatigue loading was analysed via analytical model and verified via experiment. The results show that the influence of boundary condition should be considered in T‐welded joint structure during crack propagation in weld toe area. The correction factor concerning the effect of boundary condition and modified Paris' equation was proposed according to the experimental results and verified by the following repeated experiments.     

Effects of microstructural through‐thickness non‐uniformity and crack size on fatigue crack propagation and fracture of rolled Al‐7075 alloy

Some of the fatigue tests performed using the standard compact tension (CT) and a non‐standard specimen made of rolled 7075 aluminium alloy exhibit fatigue crack growth (FCG) lagging in a small region along the crack front. Through‐thickness microstructural evaluation shows that material grains in this region did not flatten as much as other regions. In the non‐standard specimen, surface cracks are either grown under fatigue loading or broken under monotonically increasing quasi‐static loads at different crack sizes. The aforementioned lagging also exists in a narrow region of 3‐D FCG for specimens with microstructural through‐thickness non‐uniformity. A more important feature for this type of specimen with surface crack is the deflection of fast fracture direction into the grain interfaces, namely from L‐T orientation to S‐L and S‐T directions. It is proved that this is due to significant levels of second principal stresses near the free surface for small cracks and lower fracture toughness of the material in S‐L and S‐T directions.     

A literature survey on the stability and significance of residual stresses during fatigue

Many manufacturing processes can induce residual stresses in components. These residual stresses influence the mean stress during cyclic loading and so can influence the fatigue life. However, the initial residual stresses induced during manufacturing may not remain stable during the fatigue life. This paper provides a broad and extensive literature survey addressing the stability of surface and near‐surface residual stress fields during fatigue, including redistribution and relaxation due to static mechanical load, repeated cyclic loads, thermal exposure and crack extension. The implications of the initial and evolving residual stress state for fatigue behaviour and life prediction are addressed, with special attention to fatigue crack growth. This survey is not a critical analysis; no detailed attempt is made to evaluate the relative merits of the different explanations and models proposed, to propose new explanations or models or to provide quantitative conclusions. Primary attention is given to the residual stresses resulting from four major classes of manufacturing operations: shot peening and related surface treatments, cold expansion of holes, welding and machining.     

Temperature‐dependent characteristics of DH36 steel fatigue crack propagation

DH36 steel is a widely used material in marine engineering. The fatigue crack propagation rates of DH36 steel at low temperatures have a crucial influence on the fatigue strength of structures operating in polar environments. The objective of this paper is to investigate the fatigue crack propagation behaviour of DH36 steel at low temperatures (?60°C to 20°C) by carrying out tensile tests and fatigue crack propagation tests of DH36 steel, in order to obtain the fatigue crack propagation behaviour of DH36 steel. The influence of the elastic modulus on the crack length measured by the compliance method is considered. On the basis of the Paris law, the crack propagation rate at different temperatures is investigated. The results and the observed failure modes indicated that fatigue ductile‐to‐brittle transition (FDBT) occurred as the temperature was lowered.     

Fatigue crack propagation in API 5L X‐70 pipeline steel longitudinal welded joints under constant and variable amplitudes

Fatigue crack propagation (FCP) under constant and variable amplitude loading in base metal (BM), weld metal (WM) and heat affected zone (HAZ) of longitudinal welded joints of an API X‐70 pipeline steel was investigated. Constant amplitude loading tests were performed at R = 0.1 and 0.5, whereas for variable amplitude testing single peak tensile overloads (OLs) alternating between 75 and 100% of maximum load were applied at 2.5 mm intervals in crack growth. Results of SE(B) specimens tested under constant and variable amplitude loading revealed that BM, WM and HAZ regions subjected to R = 0.5 and low ΔK‐values presented the highest crack growth rates. At higher ΔK values FCP rates in all the studied regions were similar and the R effect on FCP rate was no more observed. Crack growth retardation due to OLs was observed at the three studied regions, showing a decrease on the FCP delay with a decreasing on ΔK.