Novel ZVT-PWM converters with active snubbers

An active snubber cell is proposed to contrive zero-voltage-transition (ZVT) pulsewidth-modulated (ZVT-PWM) converters. Except for the auxiliary switch, all active and passive semiconductor devices in a ZVT-PWM converter operate at zero-voltage-switching (ZVS) turn on and turn off. The auxiliary switch operates at ZVS turn off and near zero current-switching (ZCS) turn on. An analytical study on a boost ZVT-PWM converter with the proposed active snubber cell is presented in detail. A 750 W 80 kHz prototype of the boost ZVT-PWM converter has been built in the laboratory to experimentally verify the analysis. Six basic ZVT-PWM converters can be easily created by attaching the proposed active snubber cells to conventional PWM converters. A detailed design procedure of the proposed active snubber cell is also presented in this paper     

Soft Switching Circuit for Interleaved Boost Converters

A zero-voltage switching-zero-current switching interleaved boost converter is proposed in this paper. An active circuit branch in parallel with the main switches is added and it is composed of an auxiliary switch and a snubber capacitor. By using this interleaved converter topology, zero current turn-on and zero voltage turn-off of the main switches can be achieved and the reverse-recovery loss of boost diode can be reduced. In addition, the auxiliary switches are zero-voltage transmission during the whole switching transition. A prototype of boost converter rated at 1.2kW has been built to confirm the effectiveness of the converter     

A new ZVT-ZCT-PWM DC-DC converter

In this paper, a new active snubber cell is proposed to contrive a new family of pulse width modulated (PWM) converters. This snubber cell provides zero voltage transition (ZVT) turn on and zero current transition (ZCT) turn off together for the main switch of a converter. Also, the snubber cell is implemented by using only one quasi resonant circuit without an important increase in the cost and complexity of the converter. New ZVT-ZCT-PWM converter equipped with the proposed snubber cell provides most the desirable features of both ZVT and ZCT converters presented previously, and overcomes most the drawbacks of these converters. Subsequently, the new converter can operate with soft switching successfully at very wide line and load ranges and at considerably high frequencies. Moreover, all semiconductor devices operate under soft switching, the main devices do not have any additional voltage and current stresses, and the stresses on the auxiliary devices are at low levels. Also, the new converter has a simple structure, low cost and ease of control. In this study, a detailed steady state analysis of the new converter is presented, and this theoretical analysis is verified exactly by a prototype of a 1-kW and 100-kHz boost converter.     

Soft switching active snubbers for DC/DC converters

A soft-switching active snubber is proposed to reduce the turn-off losses of the insulated gate bipolar transistor (IGBT) in a buck power converter. The soft-switching snubber provides zero-voltage switching for the IGBT, thereby reducing its high turn-off losses due to the current tailing. The proposed snubber uses an auxiliary switch to discharge the snubber capacitor. This auxiliary switch also operates at zero-voltage and zero-current switching. The size of the auxiliary switch compared to the main switch makes this snubber a good alternative to the conventional snubber or even to passive low-loss snubbers. The use of the soft-switching active snubber permits the IGBT to operate at high frequencies with an improved RBSOA. In the experimental results reported for a 1 kW, 40 kHz prototype, combined switching/snubbing losses are reduced by 36% through the use of the active snubber compared to a conventional RCD snubber. The use of an active snubber allows recovery of part of the energy stored in the snubber capacitor during turn-off. The generic snubber cell for the buck power converter is generalized to support the common nonisolated DC/DC power converters (buck, boost, buck-boost, Cuk, sepic, zeta) as well as isolated DC/DC power converters (forward, flyback, Cuk, and sepic)     

有源箝位软开关充电机的设计与仿真研究

传统硬开关电路影响效率和可靠性的同时,对其他设备的电磁干扰也较大,软开关则可解决上述问题。本文提出了一种基于辅助谐振换流的新型ZVT-PWM变换器,即通过采用简单的有源辅助谐振网络实现了主、辅开关管的软开关,主开关管实现了零电压开通,开关管电流电压应力小。利用这种软开关技术研制了一台用于为风力发电蓄电池充电的充电机,给出了充电机的控制系统框图,简单介绍了充电机的工作原理。最后利用Pspice给出了运行波形和仿真结果。     

一种新型软开关DC-DC PWM升压变换器设计

为提高转换效率并降低电源开关的电流应力,提出一种基于新型有源缓冲电路的PWM DC-DC升压变换器。该有源缓冲电路使用ZVT—ZCT软开关技术,分别提供了总开关ZVT开启及ZCT闭合、辅助开关ZCS开启及ZCT闭合。消除了总开关额外的电流及电压应力,消除了辅助开关电压应力,且有源缓冲电路的耦合电感降低了电流应力。另外,通过连续将二极管添加到辅助开关电路,防止来自共振电路的输入电流应力进入总开关。实验结果表明,相比传统的PWM变换器,新的DC-DC PWM升压变换器在满负荷时电流应力降低且总体效率能达到98.7%。     

A novel active snubber for high-power boost converters

A technique which improves the performance of the boost converter by reducing the reverse-recovery-related losses in the boost switch and rectifier with an active snubber that is implemented with a minimum number of components is presented. This minimum-component-count snubber consists of a snubber inductor, an auxiliary switch, and a rectifier. The proposed technique reduces the reverse-recovery-related losses by controlling the turn-off di/dt rate of the rectifier current with the snubber inductor connected in series with the boost switch and rectifier. The voltage and current stresses of the components in the proposed active-snubber boost converter are similar to those in its conventional “hard-switched” counterpart     

An improved boost PWM soft-single-switched converter with lowvoltage and current stresses

This paper presents an improved regenerative soft turn-on and turn-off snubber applied to a boost pulsewidth-modulated (PWM) converter. The boost soft-single-switched converter proposed, which has only a single active switch, is able to operate with soft switching in a PWM way without high voltage and current stresses. This is achieved by using an auxiliary inductor, which is magnetically coupled with the main inductor of the converter. In order to illustrate the operating principle of this new converter, a detailed study, including simulations as well as experimental results, is carried out. The validity of this new converter is guaranteed by the obtained results     

High-power-factor soft-switched boost converter

A novel implementation of the high-power-factor (HPF) boost converter with active snubber is described. The snubber circuit reduces the reverse-recovery-related losses of the rectifier and also provides zero-voltage switching for the boost switch and zero-current switching for the auxiliary switch. The performance of the proposed approach was evaluated on an 80-kHz, 1.5-kW, universal-line range, HPF boost converter. The proposed technique improves the efficiency by approximately 2% at full load and low line.     

A novel lossless passive snubber for soft-switching boost-typeconverters

A novel lossless passive snubber is proposed for soft switching boost-type converters. The proposed snubber does not use any auxiliary switches, but uses two identical snubber capacitors which are charged in parallel at turn off of the main switch and discharged in series at turn on automatically, and the discharged energy is recovered effectively (more than 95% recovery) into the output capacitor. Thus, the snubber provides zero-voltage switching for the converter main switch, reducing both the turn-off losses and the electromagnetic interference (EMI) noise, which improves the converter performance. The experimental results of a 20 kHz 600 W DC-DC boost converter and a single-phase AC-DC boost rectifier with the new snubber are presented     

A new, soft-switched, high-power-factor boost converter with IGBTs

A new soft-switching technique that improves performance of the high-power-factor boost rectifier by reducing switching losses is introduced. The losses are reduced by an active snubber which consists of an inductor, a capacitor, a rectifier, and an auxiliary switch. Since the boost switch turns off with zero current, this technique is well suited for implementations with insulated-gate bipolar transistors. The reverse-recovery-related losses of the rectifier are also reduced by the snubber inductor which is connected in series with the boost switch and the boost rectifier. In addition, the auxiliary switch operates with zero-voltage switching. A complete design procedure and extensive performance evaluation of the proposed active snubber using a 1.2 kW high-power-factor boost rectifier operating from a 90 V_rms-256 V_rms input are also presented     

ZVT-PWM AC-DC boost converter with ZCS auxiliary circuit

A low conduction loss, low-cost zero-voltage-transition-pulsewidth modulation (ZVT-PWM) boost converter with a zero current switching (ZCS) auxiliary circuit is developed to achieve high-conversion-efficiency operation. The unique locations of the resonant capacitor and inductor ensure that low switching stress and commutation losses are obtained in this converter. It is very suitable for high power-factor-correction pre-regulators     

Boost Converter With Coupled Inductors and Buck–Boost Type of Active Clamp

This paper proposes a boost converter with coupled inductors and a buck-boost type of active clamp. In the converter, the active-clamp circuit is used to eliminate the voltage spike that is induced by the trapped energy in the leakage inductor of the coupled inductors. The active switch in the converter can still sustain a proper duty ratio even under high step-up applications, reducing voltage and current stresses significantly. Moreover, since both main and auxiliary switches can be turned on with zero-voltage switching, switching loss can be reduced, and conversion efficiency therefore can be improved significantly. A 200 W prototype of the proposed boost converter was built, from which experiment results have shown that efficiency can reach as high as 92% and surge can be suppressed effectively. It is relatively feasible for low-input-voltage applications, such as fuel cell and battery power conversion.     

ZVT-PWM boost converter for unity power factor applications

A new single-phase ZVT-PWM boost converter with an active snubber is proposed to achieve unity power factor operations for a wide load range. The unique location of the resonant inductor and capacitor ensures that low switching stress and commutation losses are obtained in the converter. The proposed converter is suitable for high power factor correctors     

A zero-voltage-switched PWM boost converter with an energyfeedforward auxiliary circuit

A zero-voltage-switched (ZVS) pulsewidth-modulated (PWM) boost converter with an energy feedforward auxiliary circuit is proposed in this paper. The auxiliary circuit, which is a resonant circuit consisting of a switch and passive components, ensures that the converter's main switch and boost diode operate with soft switching. This converter can function with PWM control because the auxiliary resonant circuit operates for a small fraction of the switching cycle. Since the auxiliary circuit is a resonant circuit, the auxiliary switch itself has both a soft turn on and turn off, resulting in reduced switching losses and electromagnetic interference (EMI). This is unlike other proposed ZVS boost converters with auxiliary circuits where the auxiliary switch has a hard turn off. Peak switch stresses are only slightly higher than those found in a conventional PWM boost converter because part of the energy that would otherwise circulate in the auxiliary circuit and drastically increase peak switch stresses is fed to the load. In this paper, the operation of the converter is explained and analyzed, design guidelines are given, and experimental results obtained from a prototype are presented. The proposed converter is found to be about 2%-3% more efficient than the conventional PWM boost converter     

A new family of zero-voltage-transition PWM converters with dual active auxiliary circuits

A new family of active auxiliary circuits that allow the power switch in single switch, pulsewidth modulated converters to operate with zero-voltage switching is proposed in this paper. The main feature of an auxiliary circuit belonging to this family is that the auxiliary switch can operate with a zero-current switching turn-on and turn-off without increasing the peak current stresses of the main switch. This is an improvement over previous proposed auxiliary circuits where either the auxiliary switch operates with a hard turn-off or the circuit itself increases the peak stresses of the main switch. In this paper, the fundamental principles behind the proposed family of active auxiliary circuits are explained. Based on these principles, an example auxiliary circuit is systematically derived and presented along with several other auxiliary circuits belonging to the new family. The operation of a boost converter operating with the example auxiliary circuit is discussed in detail, and general guidelines for the design and implementation of auxiliary circuits belonging to the new family are given. The feasibility of the example auxiliary circuit is confirmed by experimental results obtained from a 500-W, 100-kHz boost converter laboratory prototype.     

A new ZVT–ZCT quasi-resonant DC link for soft switching inverters

In this article, the new ZVT–ZCT Quasi-Resonant DC Link, which ensures zero crossings at any time required for soft switching (SS) and provides zero voltage transition (ZVT) turn-on and zero current transition (ZCT) turn-off together for the main switch of active snubber cell in pulse width modulated or space vector modulated operation of inverter is presented. The new circuit combines the most desirable features of the circuits presented previously and overcomes most drawbacks of these circuits by using only one auxiliary switch with fewer other components. Consequently, new ZVT–ZCT Quasi-Resonant DC Link, which is verified by a prototype of a 1.2 kW and 50 kHz circuit, is analysed in detail. All semiconductor devices operate under SS, the main switch is subjected to no additional voltage and current stresses, and the stress on the auxiliary switch is very low in the proposed new inverter.     

一种改进的ZCT无桥功率因数校正电路设计

为了降低开关损耗,提高变换器的效率,提出了一种改进的零电流转化软开关无桥功率因数校正电路,实现了变换器主开关管和辅助开关管的零电流导通和零电流关断,有效地减小了导通损耗,提高了电路的效率。详细分析了电路的工作模态、工作条件和主开关管的导通损耗。仿真和实验结果表明,该功率因数校正电路实现了输入电流对输入电压的良好跟踪,功率因数高,谐波含量少,效率较传统的全桥功率因数校正电路有明显的提高。 关键词：全桥;零电流转换;无桥;功率因数校正     

A magnetically coupled regenerative turn-on and turn-off snubberconfiguration

This paper presents a magnetically coupled regenerative turn-on and turn-off snubber configuration applied to a boost converter, which operates in continuous conduction mode (CCM). In addition to reducing the stresses in the switch, providing soft transitions in its turn-off voltage and turn-on current, it transfers the energy stored in the snubber capacitor to the load. This is achieved by using a coupled inductor mounted on the main inductor of the converter, which resets the capacitor voltage at each switching period. Design equations, as well as experimental results are presented, showing the high performance of the boost converter using the proposed snubber     

一种全桥ZVZCS DC/DC变换器的研究

提出了一种全桥零电压零电流(FB-ZVZCS)DC/DC变换器拓扑,副边采用电容和二极管构成了两个辅助电路,它们与谐振电感谐振形成的阻断电压源相串联,实现了滞后臂较大范围的ZCS,同时此种结构抑制了副边整流二极管尖峰电压;针对高输出电压设计,输出采用双全桥串联整流电路以降低整流二极管的高电压应力和解决它们的均压问题。变换器控制简单、没有辅助开关和缓冲电路。文中详细分析了工作原理和参数设计,仿真和样机实验验证了方案的正确性。