Effect of interfacial interaction on the crystallization and mechanical properties of PP/nano‐CaCO3 composites modified by compatibilizers

To investigate the effect of interfacial interaction on the crystallization and mechanical properties of polypropylene (PP)/nano‐CaCO₃ composites, three kinds of compatibilizers [PP grafted with maleic anhydride (PP‐g‐MA), ethylene–octene copolymer grafted with MA (POE‐g‐MA), and ethylene–vinyl acetate copolymer grafted with MA (EVA‐g‐MA)] with the same polar groups (MA) but different backbones were used as compatibilizers to obtain various interfacial interactions among nano‐CaCO₃, compatibilizer, and PP. The results indicated that compatibilizers encapsulated nano‐CaCO₃ particles, forming a core–shell structure, and two interfaces were obtained in the compatibilized composites: interface between PP and compatibilizer and interface between compatibilizer and nano‐CaCO₃ particles. The crystallization and mechanical properties of PP/nano‐CaCO₃ composites were dependent on the interfacial interactions of these two interfaces, especially the interfacial interaction between PP and compatibilizer. The good compatibility between PP chain in PP‐g‐MA and PP matrix improved the dispersion of nano‐CaCO₃ particles, favored the nucleation effect of nano‐CaCO₃, increased the tensile strength and modulus, but reduced the ductility and impact strength of composites. The partial compatibility between POE in POE‐g‐MA and PP matrix had little effect on crystallization and mechanical properties of PP/nano‐CaCO₃ composites. The poor compatibility between EVA in EVA‐g‐MA and PP matrix retarded the nucleation effect of nano‐CaCO₃, and reduced the tensile strength, modulus, and impact strength. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Use of silane agents and poly(propylene‐g‐maleic anhydride) copolymer as adhesion promoters in glass fiber/polypropylene composites

Two organofunctional silanes and a copolymer were used to increase the interfacial adhesion in glass fiber polypropylene (PP) reinforced composites. The performance of the coupling agents was investigated by means of mechanical property measurements, scanning electron microscopy (SEM), and dynamic mechanical analysis. The increased adhesion between the glass fibers and PP matrix observed with SEM resulted in an improvement of the mechanical and dynamic mechanical properties of the composites. Coupling achieved with the copolymer poly(propylene‐g‐maleic anhydride) (PP‐g‐MA) proved to be the most successful compared with 3‐aminopropyltrimethoxysilane and 3‐aminopropyltriethoxysilane. The combination of PP‐g‐MA with the silanes resulted in further property improvements because of the ability of the MA groups to react with the amino groups of the silanes. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 701–709, 2001     

Microstructural characteristics of glass bead‐ and wollastonite‐filled isotactic‐polypropylene composites modified with thermoplastic elastomers

Microstructural characteristics of isotactic‐polypropylene/glass bead (iPP/GB) and iPP/wollastonite (iPP/W) composites modified with thermoplastic elastomers, poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were investigated. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and dynamic mechanical analyses (DMA) showed that the iPP/SEBS and iPP/SEBS‐g‐MA blends were partially compatible two‐phase systems. Well‐dispersed spherical GB and acicular W particles without evidence of interfacial adhesion were observed in the iPP/GB and iPP/W binary composites respectively. Contrary to the blends, melt flow rates of the iPP/GB and PP/W composites decreased more with SEBS‐g‐MA than with SEBS because of enhanced interfacial adhesion with SEBS‐g‐MA elastomer. The SEM analyses showed that the ternary composites containing SEBS exhibited separate dispersion of the rigid filler and elastomer particles (i.e., separate microstructure). However, SEBS‐g‐MA elastomer not only encapsulated the spherical GB and acicular W particles completely with strong interfacial adhesion (i.e., core‐shell microstructure) but also dispersed separately throughout iPP matrix. In accordance with the SEM observations, the DSC and DMA revealed quantitatively that the rigid filler and SEBS particles in iPP matrix acted individually, whereas the rigid filler particles in the ternary composites containing SEBS‐g‐MA acted like elastomer particles because of the thick elastomer interlayer around the filler particles. The Fourier transform infrared analyses revealed an esterification reaction inducing the strong interfacial adhesion between the SEBS‐g‐MA phase and the filler particles. POLYM. COMPOS., 31:1265–1284, 2010. © 2009 Society of Plastics Engineers     

Parameters regulating interfacial and mechanical properties of short glass fiber reinforced polypropylene

The performance of thermoplastic composites is known to depend on the intrinsic properties of the two composite components, the quality of the fiber–matrix interface, and the crystalline properties of their matrix. The objective of this work is to characterize the effect of the addition of modified polypropylene (PP) and silane coupling agent on the mechanical and interfacial properties of short fiber reinforced PP composites. Differential scanning calorimetry (DSC), single fiber composite fragmentation tests (SFC), and mechanical testing are used to understand the different parameters regulating the interfacial properties of composites. No influence of the modified PP on the level of crystallinity is observed. Some differences in the size of the spherulites are observed for acrylic acid grafted PP (PP‐g‐AA). Those samples also show lower mechanical properties in spite of good interfacial interactions. Maleic anhydride grafted PP (PP‐g‐MAh) leads to better mechanical performances than PP‐g‐AA. A high MAh content PP‐g‐MAh grade with low viscosity is the best polymeric additive used in the present work. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2047–2060, 2000     

Study on poly(propylene)/ammonium polyphosphate composites modified by ethylene‐1‐octene copolymer grafted with glycidyl methacrylate

The compatibilization effect of ethylene‐1‐octene copolymer grafted with glycidyl methacrylate (POE‐g‐GMA) as an interface compatibilizer on the mechanical and combustion properties, and the morphology and structures of the cross sections of ammonium polyphosphate (APP)–filled poly(propylene) (PP) were investigated by thermogravimetry, dynamic mechanical analysis, and differential scanning calorimetry. The results indicated that the toughness of the PP/APP composites increased rapidly with adding POE‐g‐GMA; the dynamic mechanical spectra revealed that the increase of the toughness was closely related to the peaks of loss modulus (E″) and mechanical loss (tan δ). The improvement of the dispersion of APP in the PP matrix was attributed to the addition of POE‐g‐GMA; it was found that the interfacial adhesion between the filler and matrix was enhanced when the grafting material was added to the composites. Under such circumstances, the ratio of char formation was increased when the PP composites were heated, although the content of flame retardant was not changed, so the flame retardance of the material was improved. The addition of POE‐g‐GMA increased the rate of crystallization. At the same time, the degree of crystallinity and the temperature at the beginning of crystallization were decreased, although exerting little influence on the melt behavior of the crystallization of the composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 412–419, 2004     

Multiwalled carbon nanotubes‐based polypropylene composites: Influence of interfacial interaction on the crystallization behavior of polypropylene

Composites of polypropylene (PP) and multi‐walled carbon nanotubes (MWCNTs) were prepared via melt‐mixing utilizing Li‐salt of 6‐amino heaxanoic acid (Li‐AHA) modified MWCNTs in the presence of a compatibilizer (polypropylene‐g‐maleic anhydride; PP‐g‐MA). Improved interaction between the anhydride group of PP‐g‐MA and the amine functionality of Li‐AHA was confirmed via FTIR and Raman spectroscopic analysis. A higher glass transition temperature (T_g) of the PP phase has been observed in these composites as compared to pristine MWCNTs‐based composites. The crystallization temperature (T_c) of the PP phase was increased as a function of pristine MWCNTs concentration in PP/MWCNTs composites indicating hetero‐nucleating action of MWCNTs. However, T_c value was decreased in the presence of Li‐AHA modified MWCNTs indicating the adsorbed Li‐AHA on the MWCNTs surface. Moreover, T_c value was higher in the presence of Li‐AHA modified MWCNTs with PP‐g‐MA as compared to that of without PP‐g‐MA, suggesting the desorbed Li‐AHA from the MWCNTs surface due to melt‐interfacial reaction. Further, MWCNTs were extracted by hot vacuum filtration technique from PP/MWCNTs composites containing Li‐AHA and PP‐g‐MA. The isothermal crystallization kinetics showed a variation in crystallization behavior of the PP phase in the corresponding composites as compared to the “extracted MWCNTs.” POLYM. ENG. SCI., 57:183–196, 2017. © 2016 Society of Plastics Engineers     

Preparation and performance characteristics of short‐glass‐fiber/maleated styrene–ethylene–butylene–styrene/polypropylene hybrid composites

Eighty/twenty polypropylene (PP)/styrene–ethylene–butylene–styrene (SEBS) and 80/20 PP/maleated styrene–ethylene–butylene–styrene (SEBS‐g‐MA) blends reinforced with 30 wt % short glass fibers (SGFs) were prepared by extrusion and subsequent injection molding. The influence of the maleic anhydride (MA) functional group grafted to SEBS on the properties of SGF/SEBS/PP hybrid composites was studied. Tensile and impact tests showed that the SEBS‐g‐MA copolymer improved the yield strength and impact toughness of the hybrid composites. Extensive plastic deformation occurred at the matrix interface layer next to the fibers of the SGF/SEBS‐g‐MA/PP composites during impact testing. This was attributed to the MA functional group, which enhanced the adhesion between SEBS and SGF. Differential scanning calorimetry measurements indicated that SEBS promoted the crystallization of PP spherulites by acting as active nucleation sites. However, the MA functional group grafted to SEBS retarded the crystallization of PP. Finally, polarized optical microscopy observations confirmed the absence of transcrystallinity at the glass‐fiber surfaces of both SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrid composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1303–1311, 2002     

A compatibilized composite of recycled polypropylene filled with cellulosic fiber from recycled corrugated paper board: Mechanical properties,morphology, and thermal behavior

This article deals with the feasibility of using recycled corrugated paper board (rPF) as the reinforcing material for recycled plastics. The composites of recycled polypropylene (rPP) and rPF were prepared by extrusion compounding and injection molding, and the rPP/rPF composites compatibilized by maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted ethylene‐1‐octene copolymer (POE‐g‐MA), and maleic anhydride grafted styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA) were also prepared. The crystallization and melting behavior, mechanical properties, thermal stability, and morphology of these composites were studied. The results indicated that rPF promoted the crystallization, enhanced the strength and toughness of rPP/rPF composites to some extent while decreased thermal stability at the same time. PP‐g‐MA and POE‐g‐MA improved the dispersion and interface adhesion of rPF, and further upgraded the mechanical properties and vicat softening temperatures. Among these compatibilizers, PP‐g‐MA was most favorable to the strength improvement while POE‐g‐MA was most favorable to the toughness improvement. As for SEBS‐g‐MA, it had no obvious modification effect. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Glass fiber reinforced and β‐nucleating agents regulated polypropylene: A complementary approach and a case study

A two‐step process for preparing glass fibers (GFs) reinforced β‐nucleated PP composites was designed and developed. The complementary approach combined GFs reinforcement and β‐nucleating agents regulation using N,N′‐dicyclohexyl‐2,6‐napthalene‐dicarboxamide (TMB‐5) in the presence of maleic anhydride grafted polypropylene (PP‐g‐MA) through extrusion blending. The influence of TMB‐5 and GFs on the mechanical properties and crystallization behavior of PP was studied by mechanical test, wide‐angle X‐ray diffraction, differential scanning calorimetry, and scanning electron microscopy. A distinct complementary effect of GFs and β‐nucleating agent TMB‐5 on mechanical properties and crystallization behavior of PP was observed. Results showed that addition of 20 wt % GFs and 0.1 wt % TMB‐5 into PP matrix with the two‐step process could lead to significant increase to its mechanical properties: specifically 64.8% improvement in tensile strength, 107.1% enhancement in flexural modulus, and 167.7% increasement in notched impact strength compared to that of neat PP. Furthermore, with the combination of TMB‐5 and GFs, not only led to promoted interfacial adhesion, but also significantly improved overall comprehensive mechanical properties. The complementary process provided an alternative approach for the development of PP with balanced toughnesss and stiffness. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45768.     

Effect of silane‐grafted polypropylene on the mechanical properties and crystallization behavior of talc/polypropylene composites

Talc‐filled polypropylene (PP) composites coupled with silane‐grafted polypropylene (PP‐g‐Si) were prepared. Effect of PP‐g‐Si on the mechanical properties, crystallization, and melting behavior of PP composites was investigated. Compared with the uncoupled composites, the mechanical properties of Talc/PP composites coupled with a small amount of PP‐g‐Si were increased to some extent. Meanwhile, PP‐g‐Si can promote crystallization rate and increase crystallization temperature of PP in the composites. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2974–2977, 2000     

Study on the microstructures and mechanical behaviour of compatibilized polypropylene/polyamide‐6 blends

A series of blends of polypropylene (PP)–polyamide‐6 (PA6) with either reactive polyethylene–octene elastomer (POE) grafted with maleic anhydride (POE‐g‐MA) or with maleated PP (PP‐g‐MA) as compatibilizers were prepared. The microstructures and mechanical properties of the blends were investigated by means of tensile and impact testing and by scanning electron microscopy and transmission electron microscopy. The results indicated that the miscibility of PP–PA6 blends was improved with the addition of POE‐g‐MA and PP‐g‐MA. For the PP/PA6/POE‐g‐MA system, an elastic interfacial POE layer was formed around PA6 particles and the dispersed POE phases were also observed in the PP matrix. Its Izod impact strength was four times that of pure PP matrix, whilst the tensile strength and Young's modulus were almost unchanged. The greatest tensile strength was obtained for PP/PA6/PP‐g‐MA blend, but its Izod impact strength was reduced in comparison with the pure PP matrix. © 2002 Society of Chemical Industry     

Rheological behaviors of glass bead‐ and wollastonite‐filled polypropylene composites modified with thermoplastic elastomers

Steady‐ and oscillatory‐shear rheological behaviors of polypropylene/glass bead (PP/GB) and PP/wollastonite (PP/W) melts modified with thermoplastic elastomers, poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and the corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were examined by means of a parallel‐plate rheometer. With adding the elastomers (SEBS and SEBS‐g‐MA) and fillers (spherical GB and acicular W) to PP, viscosity especially at low shear rates and shear‐thinning flow behavior at high shear rates were pronounced as evidenced quantitatively by Carreau–Yasuda (CY) parameters, but Cox–Merz analogy became weakened. Besides, melt‐elasticity in terminal region and relaxation time (t_c) in crossing point increased, indicating an enhancement in quasi‐solid behavior of molten PP. Comparing with the elastomers, rheological behaviors of molten PP were more influenced with adding the rigid fillers, especially with W due to distinct acicular shape of W particles. SEBS‐g‐MA elastomer more affected rheological behaviors of the ternary composites than SEBS elastomer, implying that SEBS elastomer and the filler particles behaved individually (i.e., development of separate microstructure) in (PP/GB)/SEBS and (PP/W)/SEBS ternary composites, but core‐shell microstructure developed with strong interfacial adhesion by adding SEBS‐g‐MA elastomer, and the filler particles encapsulated with the thick SEBS‐g‐MA elastomer interlayer (i.e., core‐shell particles) acted like neither big elastomer particles nor like individual rigid particles in melt‐state. Moreover, effects of SEBS‐g‐MA elastomer reached a maximum on rheological behaviors of (PP/W)/SEBS‐g‐MA ternary composite, indicating a synergy between core‐shell microstructure and acicular W particles. Correlations between oscillatory‐shear flow properties and microstructures of the blends and composites were evaluated using Cole–Cole (CC), Han–Chuang (HC), and van Gurp–Palmen (vGP) plots. COMPOS., 2012. © 2012 Society of Plastics     

Investigation on morphology and mechanical properties of polyamide 6/maleated ethylene‐propylene‐diene rubber/organoclay composites

Maleated ethylene‐propylene‐diene rubber (EPDM‐g‐MA) toughened polyamide 6 (PA6)/organoclay (OMMT) nanocomposites were prepared by melt blending. The role of OMMT in the morphology of the ternary composites and the relationship between the morphology and mechanical properties were investigated by varying the blending sequence. The PA6/EPDM‐g‐MA/OMMT (80/20/4) composites prepared by four different blending sequences presented distinct morphology and mechanical properties. The addition of OMMT could obviously decrease viscosity of the matrix and weaken the interfacial interactions between PA6 and EPDM‐g‐MA when blending EPDM‐g‐MA with a premixed PA6/OMMT nacocomposite, resulting in the increase of rubber particle size. The final mechanical properties are not only determined by the location of OMMT, but also by the interfacial adhesion between PA6 and EPDM‐g‐MA. Having maximum percentage of OMMT platelets in the PA6 matrix and keeping good interfacial adhesion between PA6 and EPDM‐g‐MA are beneficial to impact strength. POLYM. ENG. SCI., 2009. © 2008 Society of Plastics Engineers     

Phase structure and morphology of wollastonite‐reinforced polypropylene composites modified with SEBS and SEBS‐g‐MA elastomers

Supermolecular structure of isotactic polypropylene/wollastonite/styrenic rubber block copolymers composites were studied as a function of elastomeric poly‐ (styrene‐b‐ethylene‐co‐butylene‐b‐styrene) triblock copolymer (SEBS) and the SEBS grafted with maleic anhydride (SEBS‐g‐MA) content (from 0 to 20 vol%) by optical, scanning, and transmission electron microscopy, wide‐angle X‐ray diffraction and differential scanning calorimetry. Wollastonite particles disturbed the spherulitization of polypropylene matrix. Both elastomers affected the crystallization of polypropylene matrix mainly by solidification effect. Although SEBS‐g‐MA encapsulated wollastonite particles more expressive than SEBS forming thus core‐shell morphology in higher extent, scanning electron micrographs indicated more constrained wollastonite particles in fractured surfaces of composites with SEBS elastomer. Moreover, SEBS‐g‐MA disorientated wollastonite particles and affected reorientation of the polypropylene crystallites stronger than SEBS elastomer. POLYM. ENG. SCI., 47:2145–2154, 2007. © 2007 Society of Plastics Engineers     

The physical and mechanical properties of beta‐nucleated polypropylene/montmorillonite nanocomposites

Polypropylene (PP) and polypropylene/polypropylene‐g‐maleic anhydride/ organomontmorillonite (PP/PP‐g‐MA/OMMT) nanocomposites were modified with 0.05 to 0.3% (w/w) of the aryl amide β‐nucleator to promote the formation of hexagonal crystal modification (β‐phase) during melt crystallization. The nonisothermal crystallization behavior of PP, PP/PP‐g‐MA/OMMT and β‐nucleated PP/PP‐g‐MA/OMMT nanocomposites were studied by means of differential scanning calorimetry. Structure‐property relationships of the PP nanocomposites prepared by melt compounding were mainly focused on the effect and quantity of the aryl amide nucleator. The morphological observations, obtained from scanning electron microscopy, transmission electron microscopy and X‐ray diffraction analyses are presented in conjunction with the thermal, rheological, and mechanical properties of these nanocomposites. Chemical interactions in the nanocomposites were observed by FT‐IR. It was found that the β‐crystal modification affected the thermal and mechanical properties of PP and PP/PP‐g‐MA/OMMT nanocomposites, while the PP/PP‐g‐MA/OMMT nanocomposites of the study gained both a higher impact strength (50%) and flexural modulus (30%) compared to that of the neat PP. β‐nucleation of the PP/PP‐g‐MA/OMMT nanocomposites provided a slight reduction in density and some 207% improvement in the very low tensile elongation at break at 92% beta nucleation. The crystallization peak temperature (T_cp) of the PP/PP‐g‐MA/OMMT nanocomposite was slightly higher (116°C) than the neat PP (113°C), whereas the β‐nucleation increased the crystallization temperature of the PP/PP‐g‐MA/OMMT/aryl amide to 128°C, which is of great advantage in a commercial‐scale mold processing of the nanocomposites with the resulting lower cycle times. The beta nucleation of PP nanocomposites can thus be optimized to obtain a better balance between thermal and mechanical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Synthesis of a new compatibilisant agent PVC‐g‐MA and its use in the PVC/alfa composites

The main objective of this research was to synthesize a new compatibilisant agent (PVC‐g‐MA), which was grafted from the maleic anhydride on the PVC chains. The presence of maleic anhydride grafting on PVC was made evident by infrared analysis. PVC‐g‐MA was used like compatibilisant to solve the problem of the incompatibility between the hydrophobic polymeric matrix (PVC) and hydrophilic fiber (alfa). Composites samples were prepared with different alfa fiber loading (10, 20, and 30 wt %) and incorporating PVC‐g‐MA (1, 3, and 5 wt %) or PP‐g‐MA (3 wt %). The tensile properties, the thermal stability and the morphology of the composites were investigated. The result indicated that the PVC‐g‐MA increased the interfacial adhesion between the fibers and the polymer matrix and this effect was better than that obtained for the maleated‐polypropylene‐coupled composites. Microstructure analysis of the fractured surfaces of MAPP modified composites confirmed improved interfacial bonding. The addition of alfa and PVC‐g‐MA increased the thermal stability of the composites. The temperature of degradation of the polymer matrix increased about 16°C in comparison to the noncoupled composite, indicating that PVC‐g‐MA improved the thermal stability of the polymer. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Investigation on β‐polypropylene/PP‐g‐MAH/ surface‐treated calcium carbonate composites

β‐Polypropylene composites containing calcium carbonate treated by titanate coupling agent (T‐CaCO₃) and maleic anhydride grafted PP (PP‐g‐MAH) were prepared by melt compounding. The crystallization, morphology and mechanical properties of the composites were investigated by means of differential scanning calorimetry, wide‐angle X‐ray diffraction, polarized light microscopy, scanning electron microscopy and mechanical tests. It is found that both T‐CaCO₃ and NT‐C are able to induce the formation of β‐phase, and NT‐C greatly increases the β content and decreases the spherulitic size of PP. PP‐g‐MAH facilitates the formation of β‐form PP and improves the compatibility between T‐CaCO₃ and PP. Izod notched impact strength of β‐PP/T‐CaCO₃ composite is higher than that of PP/T‐CaCO₃ composite, indicating the synergistic toughening effect of T‐CaCO₃ and β‐PP. Incorporation of PP‐g‐MAH into β‐PP/T‐CaCO₃ composite further increases the content of β‐crystal PP and improves the impact strength and tensile strength when T‐CaCO₃ concentration is below 5 wt%. The nonisothermal crystallization kinetics of β‐PP composites is well described by Jeziorny's and Mo's methods. It is found that NT‐C and T‐CaCO₃ accelerate the crystallization rate of PP but the influence of PP‐g‐MAH on crystallization rate of β‐PP composite is marginal. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Peroxide‐catalyzed swell grafting of maleic anhydride onto polypropylene

A new grafting method was developed to incorporate maleic anhydride directly onto solid‐state polypropylene powders. Maleic anhydride grafts altered the nonpolar characteristics of polypropylene so that much better mixing was achieved in blends and composites of polypropylene with many other polymers and fillers. Maleic anhydride was grafted onto polypropylene by the peroxide‐catalyzed swell grafting method, with a maximum extent of grafting of 4.60%. Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy, tensile testing, and impact testing were used to characterize the isotactic polypropylene (iPP), maleic anhydride grafted polypropylene (MAH‐g‐iPP), and (isotactic polypropylene)/(calcium carbonate) composites (iPP/CaCO₃). The crystallinity and heat of fusion of the MAH‐g‐iPP decreased as the extent of grafting increased. The mechanical properties of the CaCO₃ filled polypropylene were improved by adding MAH‐g‐iPP as a compatibilizing agent. The dispersion of the fillers in the polymer matrix and the adhesion between the CaCO₃ particles and the polymer matrix were improved by adding the compatibilizer.     

The crystallization,thermal and mechanical properties of nano‐Sb2O3 filled poly(butylene terephthalate)

Nano‐Sb₂O₃ particles were modified by a combination modifier of cetyltrimethyl ammonium bromide (CTAB) and KH‐560 via the mechanochemical method based on high‐energy ball milling. Then, the testing specimens of the nano‐Sb₂O₃/PBT composites of differing compositions were prepared by melting blending technology. The crystallization, thermal, and mechanical properties of composites were characterized by X‐ray diffraction, differential scanning calorimetry, thermogravimetric analyzer, and mechanical performance test. The tensile and impact fracture surfaces of composites were determined by scanning electron microscopy. Besides, the influence of the Sb₂O₃ nanoparticles surface modification on crystallinity, mechanical properties of the composites, and the interfacial adhesion between nano‐Sb₂O₃ and PBT was systematically investigated. The results indicate that the main crystalline characteristics of PBT matrix remain unchanged in the nanocomposites. However, the addition of nano‐Sb₂O₃ particles plays a heterogeneous nucleation and can effectively improve the crystallization of PBT matrix. In addition, the compound modification of the nano‐Sb₂O₃ can effectively enhance mechanical properties of the composites and interfacial interaction between nano‐Sb₂O₃ and PBT. The enhanced fracture properties in the nanocomposites were caused by the assisted void formation at the edge of the nano‐Sb₂O₃ particle. When the nano‐Sb₂O₃ mass fraction is 3%, the composites show excellent comprehensive performance. The interfacial adhesion parameter B and the half‐debonding angle θ of composites were assessed to quantitatively characterize the interfacial adhesion strength between nano‐Sb₂O₃ and PBT. Finally, the reinforcement and toughening mechanisms were described. J. VINYL ADDIT. TECHNOL., 26:268–281, 2020. © 2019 Society of Plastics Engineers     

Mechanical properties and viscoelastic behavior of basalt fiber‐reinforced polypropylene

In the present article, a series of commercial‐grade polypropylenes (PP) filled with different contents of short basalt fibers were studied. This composite material presented deterioration of both mechanical characteristics, for example, stress and strain at yield with increasing of the fiber content. On the other hand, the impact strength was fourfold higher than that of unfilled PP. A poor adhesion between the PP matrix and the basalt fibers was detected. This is why interfacial interactions were promoted by the adding of poly(propylene‐g‐maleic anhydride) (PP‐g‐MA). It was observed that the tensile properties of the obtained materials and their impact strengths increased significantly with increasing of the amount of PP‐g‐MA in the blend. The adhesion improvement was confirmed by scanning electron microscopy as well. Fourier transform infrared spectroscopy was applied to assess if any chemical interactions in the system PP/PP‐g‐MA/basalt fibers exist. Dynamic mechanical thermal analysis data showed an increase of the storage modulus with increasing fiber content. The conclusion was made that the modification of the PP matrix led to a higher stiffness but its value remained constant, irrespective of the PP‐g‐MA content. With increasing fiber content, damping in the β‐region decreased, but increase of the coupling agent content restored its value back to that of PP. The loss modulus spectra presented a strong influence of fiber content on the α‐relaxation process of PP. The position of the peaks of the above‐mentioned relaxation processes are discussed as well. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 523–531, 1999