炭黑/白炭黑双相填料补强BIIR/PP热塑性弹性体的性能研究

通过动态硫化工艺制备了溴化丁基橡胶（BIIR）/聚丙烯（PP）热塑性弹性体,研究了加工时间、填料、硫化剂对弹性体力学性能的影响。结果表明,动态硫化制备热塑性弹性体的时间约为13 min;使用炭黑N330/白炭黑双相填料的热塑性弹性体具有较好的力学性能;在氧化锌、硫磺、溴化辛基酚醛树脂及硫磺/溴化辛基酚醛树脂并用硫化体系中,溴化辛基酚醛树脂硫化的热塑性弹性体力学性能最佳。     

A study of dynamic vulcanization for polyamide‐12 and chlorobutyl rubber

Polyamide‐12 and chlorobutyl rubber were blended by dynamic vulcanization in a high shear environment using curing systems based on sulfur, dithiocarbamate/ZnO, and 4,4‐methylenebiscyclohexylamine/MgO. As expected, all blends with curing agents show increased tensile strength and elongation at break in comparison to blends without curing agents. Maximum mechanical properties are obtained at relatively low levels of curing agent in all systems. Hexane extraction of the mixtures and measurement of percentage of insolubles along with the swelling index of the rubber phase confirm that a high level of cure is achieved at low levels of curing agent. Although the curatives are designed for the rubber phase, differential scanning calorimetry results indicate that both phases are affected during the dynamic vulcanization process, with polyamide‐12 showing a reduced melting temperature that is indicative of molecular weight reduction, structure changes, or reaction with the rubber phase. Scanning electron microscopy results indicate that phase size is reduced with increased blending time and level of curing agent. Rheological studies indicate that blends containing curing agents exhibit non‐Newtonian behavior to a greater extent than polyamide or nonvulcanized polyamide/chlorobutyl rubber blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 871–880, 2003     

Influences of blend proportions and curing systems on dynamic,mechanical, and morphological properties of dynamically cured epoxidized natural rubber/high‐density polyethylene blends

Thermoplastic elastomers (TPEs) based on dynamically cured epoxidized natural rubber/high‐density polyethylene (ENR/HDPE) blends were prepared. Influence of the process oil, blend proportion, and curing systems were investigated. It was found that the oil‐extended thermoplastic vulcanizates (TPVs) exhibited better elastomeric properties and improved ease of the injection process. Increasing the proportion of ENR caused increasing elastic response of elongation at break, tension set properties, and tan δ. It was also found that the TPV treated with phenolic resin exhibited superior mechanical properties and the smallest vulcanized rubber domains. The TPV treated with the conventional peroxide co‐agent curing system showed superior strength properties but had poor elastomeric properties. POLYM. ENG. SCI., 2009. © 2008 Society of Plastics Engineers     

硅橡胶/聚氨酯热塑性弹性体的制备

采用过氧化物硫化体系制备了硅橡胶(VSR)与聚氨酯(TPU)质量比为50/50的VSR/TPU热塑性弹性体。考察了VSR的硫化条件,研究了抑制剂4-羟基2,2,6,6-四甲基哌啶氧(TEMPO)用量对VSR/TPU体系动态硫化过程及性能的影响。结果表明,当Hakke流变仪转速为110 r/min、硫化温度为180℃、硫化剂2,5-二甲基-2,5双(过氧化叔丁基)己烷用量为1.0份(质量,下同)、抑制剂TEMPO用量为0.3份时,制备的VSR/TPU热塑性弹性体具有较精细的相态,分散相VSR在TPU连续相中分散较均匀,热塑性弹性体的拉伸强度及扯断伸长率分别达到4.4 MPa及291%,流变性能较好,压缩永久变形最小。     

阻燃,抗静电NBR／PVC热塑性弹性体的制备

用动态硫化法制备了具有阻燃、抗静电性能的丁腈橡胶／聚氯乙烯热塑性弹性体,研究了橡塑共混比、导电炭黑、阻燃剂、硫化剂用量以及返炼等对ＴＰＥ的导电性、阻燃性及力学性能的影响。结果表明,为得到综合性能较好的热塑性弹性体,较适宜的制备条件为ＮＢＲ／ＰＶＣ配比为６０／４０、导电炭黑用量为３０、氢氧化铝用量为４０、硫黄用量为１．３。     

The effect of curing system on the properties of the thermoplastic elastomer foams of ethylene‐vinyl acetate copolymer and styrene‐butadiene and ethylene‐propylene‐diene monomer rubbers

Thermoplastic elastomer (TPE) foams have important application in electrical, toys, and other industries. Several foams were prepared by ethylene‐vinyl acetate copolymer (EVA) lonely, and in combination with styrene‐butadiene and ethylene‐propylene‐diene monomer rubbers (SBR and EPDM). The effects of crosslinking and foaming agents and EVA type on density and mechanical properties of the cured foams with two curing systems, peroxide and sulfur‐peroxide with potential use in automotive applications, were studied. The results showed that proposed compounds formulations were foamed properly. The viscosity of the EVA was a key factor for the density values of the formed foams. The densities of the cured foams with peroxide system with various SBR contents were higher when compared with cured foams with sulfur‐peroxide system. With increasing foaming agent, the densities of the foams were reduced for studied curing systems. The densities of the EVA–EPDM foams were lower than those of the EVA–SBR foams in the same studied conditions. Increasing rubber in foam formulation had adverse effect on tensile properties of the foams. The existence of the talc powder in foam formulation had important role on the shape and type of the formed cells and resulted in foams with mostly closed cells. The results of this study help the automotive article designer to produce suitable TPE foam. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45357.     

硫化剂对陶瓷化耐火硅橡胶性能的影响

研究了2,5-二甲基-2,5-二（叔丁基过氧基）己烷（俗称双二五）、2,4-二氯过氧化苯甲酰（俗称双二四）、过氧化二异丙苯（DCP）3种硫化剂对陶瓷化耐火硅橡胶力学性能和烧结性能的影响。结果表明,一次硫化和二次硫化后,使用DCP做硫化剂的硅橡胶的硬度都是最大,使用双二五做硫化剂的硅橡胶的拉断伸长率都是最高,采用双二四做硫化剂的硅橡胶拉伸强度都是最大;使用双二四做硫化剂的硅橡胶烧结硬度最高。综合来看,使用双二四作硫化剂时陶瓷化耐火硅橡胶的力学性能最好,其最佳用量为1.25份。     

Solvent resistance and mechanical properties in thermoplastic elastomer blends prepared by dynamic vulcanization

Dynamic vulcanization was used to prepare thermoplastic elastomer blends of nylon (polyamide), polypropylene (PP) and polybutylene terephthalate thermoplastics with chlorobutyl (CIIR) and nitrile (NBR) rubbers. Mechanical properties of the blends were correlated against composition. Although hardness and tensile strength increase with increasing thermoplastic content for all blends, elongation at break values initially decrease and then increase in the range of 20–40% thermoplastic. For various blend compositions, the swelling behavior was evaluated with solvents that are able to dissolve the uncured rubber portion but not the thermoplastic component of the mixtures. All five systems showed swelling index values that were substantially less than the calculated “theoretical” values of swelling index. This was attributed to a caging effect of the thermoplastic component on the rubber phase, which restricts access of solvent and swelling of the rubber phase. In turn, this affects the solvent resistance of the blend. Some of the blends were evaluated by differential scanning calorimetry to assess the compatibility of the components in the blend. scanning electron microscopy was also used to determine the degree of compatibility of the two phases generated in the mixing process. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mechanical properties of thermoplastic elastomers based on silicone rubber and an ethylene–octene copolymer by dynamic vulcanization

Thermoplastic vulcanizates (TPVs) are a special class of thermoplastic elastomers that are generally produced by the simultaneous mixing and crosslinking of a rubber with a thermoplastic polymer at an elevated temperature. Novel peroxide‐cured TPVs based on blends of silicone rubber and the thermoplastic Engage (an ethylene–octene copolymer) have been developed. These TPVs exhibit very good overall mechanical and electrical properties. With an increasing concentration of dicumyl peroxide, the tensile strength, modulus, and hardness of the TPVs increase, whereas the elongation at break decreases. Significant correlations have been obtained from oscillating disc rheometer torque values with various physical properties, such as the modulus and tension set of the TPVs. The aging characteristics and recyclability of the silicone‐based TPVs are also excellent. Scanning electron microscopy photomicrographs of the TPVs have confirmed a dispersed phase morphology. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

SBS and SEBS block copolymers as impact modifiers for polypropylene compounds

Blends of polypropylene (PP) and thermoplastic elastomers (TPE), namely SBS (styrene‐butadiene‐styrene) and SEBS (styrene‐ethylene/1‐butene‐styrene) block copolymers, were prepared to evaluate the effectiveness of the TPE type as an impact modifier for PP and influence of the concentration of elastomer on the polymer properties. Polypropylene homopolymer (PP‐H) and ethylene–propylene random copolymer (PP‐R) were evaluated as the PP matrix. Results showed that TPEs had a nucleating effect that caused the PP crystallization temperature to increase, with SBS being more effective than SEBS. Microstructure characterization tests showed that in most cases PP/SEBS blends showed the smallest rubber droplets regardless of the matrix used. It was seen that SEBS is a more effective toughening agent for PP than SBS. At 0°C the Izod impact strength of the PP‐H/SEBS 30% b/w blend was twofold higher than the SBS strength, with the PP‐R/SEBS 30% b/w blend showing no break. A similar behavior on tensile properties and flexural modulus were observed in both PP/TPE blends. Yield stress and tensile strength decreased and elongation at break increased by expanding the dispersed elastomeric phase in the PP matrix. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 254–263, 2005     

CR/HPVC热塑性弹性体的性能研究

选用氯丁橡胶（CR）和高聚合度聚氯乙烯（HPVC）为主体材料，用动态硫化法制备了一类性能优异的材料－CR／HPVC共混型热塑性弹性体（TPE）。研究了共混方法、硫化温度、硫化体系、硫化剂用量及硫化时间等因素对动态硫化CR／HPVC热塑性弹性体力学性能的影响。     

动态硫化PSBR/PE共混型热塑性弹性体的研究

采用动态硫化法制备了粉末丁苯橡胶（PSBR）／聚乙烯（PE）共混型热塑性弹性体（TPO），研究了共混比、硫化体系、填料种类及用量、加工工艺对共混胶力学性能的影响。结果表明，当PSBR／PE共混比为60／40并采用传统硫化体系、白炭黑作补强剂时，TPO综合性能较好。     

Polymeric curing agent reinforced silicone rubber composites with low viscosity and low volume shrinkage

A new type of polymeric curing agent (PCA) was synthesized to improve processing property, increase mechanical properties, and decrease volume shrinkage of silicone rubber. The PCA was prepared by co‐hydrolysis condensation of dimethyldiethoxysilane (DDS) and polyethoxysiloxane, then modified by hexamethylcyclotrisilazane (D₃^N). Commercial silica and tetraethoxysilane (TEOS) were used as controls simultaneously. The properties of polydimethylsiloxane (PDMS) composites were characterized by shear viscosity measurements, room temperature mass loss, linear volume shrinkage, stress‐strain tests, swelling behaviors and thermogravimetric analysis (TGA). PDMS composites using PCA show lower shear viscosity than those using commercial silica. Compared with the traditional PDMS/TEOS curing systems, PDMS/PCA curing systems behave relatively lower volume shrinkage, better reinforcement and thermal properties. In short, PCA acts as a good compromise in providing the best balance of processing property, volume shrinkage, mechanical properties and thermal stability in silicone rubber composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of dicumyl peroxide and phenolic resin as a mixed curing system on the mechanical properties and morphology of TPVs based on HDPE/ground tire rubber

Thermoplastic vulcanizates (TPVs) are a special group of thermoplastic elastomer with the characteristic that consists of rubber elasticity and the processability of thermoplastic polymers. TPVs based on high density polyethylene (HDPE)/ground tire rubber (GTR) with phenolic resin (HY‐2045) and dicumyl peroxide (DCP) as vulcanizing agents are prepared through dynamic vulcanization in this article. The blends consisting of 40/60 HDPE/GTR are melt‐mixed in an internal mixer and then pressed with a compression molding machine. The aim of this experiment is to study the influence of a compound curing agent system on the mechanical properties of the HDPE/GTR composites. The results indicate that the mechanical properties of the HDPE/GTR blends are improved significantly by adding 4 phr HY‐2045 and 0.3 phr DCP than those of TPVs without any vulcanizing agents after dynamic vulcanization. The X‐ray photoelectron spectroscopy study and the FTIR‐ATR analysis confirmed that the crosslinking phenomenon occurred in the preparation of TPVs; and the gel fraction analysis indicates that the GTR components and the HDPE components of the HDPE/GTR blends are all moderately crosslinked. In addition, the morphology of the HDPE/GTR blends has been investigated by scanning electron microscopy. POLYM. COMPOS., 36:1907–1916, 2015. © 2014 Society of Plastics Engineers     

Mechanical properties and antibacterial activity of peroxide‐cured silicone rubber foams

Silicone rubber (SR) foams were prepared by the peroxide curing of a silicone compound with 2,4‐dichlorobenzoyl peroxide (DCBP), di‐t‐butyl peroxide (DTBP), or 2,5‐dimethyl‐2,5‐di(t‐butylperoxy) hexane (DBPH) in the presence of 2,2′‐azobisisobutyronitrile (AIBN) as a blowing agent. The cells were formed in the foam as a result of nitrogen produced by the decomposition of AIBN during the foaming process. The cell size, hardness, and tensile properties of the SR foams were examined as a function of the peroxide concentration. When the peroxide concentration increased, the hardness and tensile strength of the SR foams increased, whereas the cell size and elongation at break decreased. The antibacterial activity of the prepared foams was also evaluated via their effects on Staphylococcus aureus and Escherichia coli. The peroxide‐cured SR foams had antibacterial activity because a toxic residue was generated by the peroxide decomposition. The foam prepared by the AIBN/DCBP system showed more antibacterial activity than the AIBN/DBPH and AIBN/DTBP ones. However, after postcuring at 250°C for 2 h, the antibacterial activity of the SR foams significantly decreased. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polypropylene/natural rubber thermoplastic elastomer: Effect of phenolic resin as a vulcanizing agent on mechanical properties and morphology

The aim of this study is to characterize thermoplastic elastomers (TPEs) from polypropylene and natural rubber with and without phenolic resin as a vulcanizing agent. The blends containing 40–60 wt % of polypropylene were mixed in an internal mixer and pressed with a compression molding machine. TPEs without rubber vulcanization, named as unvulcanized thermoplastic natural rubber (uTPNR) were compared to TPEs containing dynamic vulcanized rubber, referred as vulcanized thermoplastic natural rubber (vTPNR). The uTPNRs illustrated cocontinuous phase morphology, whereas the vTPNRs displayed dispersed phase of vulcanized natural rubber. Tensile properties, tear strength, thermal ageing resistance, ozone resistance, tension set, hardness and swelling test in toluene, IRM 903 oil and engine oil were carried out according to ASTM. It was found that tensile and tear strength, hardness and tension set of the uTPNRs increased with increasing polypropylene content. Dynamic vulcanization improved tensile strength, elongation at break, tension set and degree of swelling of the TPEs, whereas hardness and tear strength did not show significant change after dynamic vulcanization. The vTPNRs exhibited higher ozone resistance and swelling resistance than the uTPNRs. Reprocessability of the vTPNRs was investigated and showed that tensile strength decreased at 20 and 30% and elongation at break decreased at 13 and 27% for the first and the third reprocessing respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

In situ reactive compatibilization and reinforcement of peroxide dynamically vulcanized polypropylene/ethylene‐propylene‐diene monomer tpv by zinc dimethacrylate

This work demonstrates an approach of in situ reactive compatibilization between polypropylene (PP) and ethylene‐propylene‐diene monomer (EPDM) by using ZDMA as a compatibilizer and, simultaneously, as a very strong reinforcing agent. With 7phr ZDMA in the PP/EPDM (30/70, w/w) thermoplastic vulcanizate (TPV), the tensile strength and elongation at break were increased from 5.3 MPa and 222% up to 11.2 MPa and 396%, respectively. Increasing the PP concentration further improved mechanical properties of the TPVs with ZDMA. This tremendous reinforcing as well as the compatibilization effect of the ZDMA was understood by polymerization of ZDMA and ZDMA reacting with EPDM and PP during peroxide induced dynamic vulcanization. A peculiar nano‐composite structure that the crosslinked rubber particles were “bonded” by a transition zone which containing numerous of nano‐particles with dimensions of about 20–30 nm was observed from transmission electron microscopy (TEM). Scanning electron microscopy (SEM) results showed that increase of PP/EPDM ratio reduced the size of crosslinked EPDM particles. Moreover, we found that the ZDMA reinforced EPDM particles resulted in a higher tan δ peak temperature for EPDM phase and built “filler‐filler”‐like networking in the PP melt. POLYM. COMPOS. 34:1357–1366, 2013. © 2013 Society of Plastics Engineers     

丁腈橡胶／PVC型动态硫化热塑性弹性体性能研究

利用开炼机,通过动态硫化法制成的共混物丁腈橡胶／ＰＶＣ型热塑性弹性体（ＴＰＥ）,经透射电镜观察,呈现出明显的两相结构,交联的丁腈橡胶分散相分散于ＰＶＣ连续相中。共混物的力学性能受硫化体系和加工条件的影响。永久压缩变形、永久拉伸断裂变形、耐油等主要性能均优于简单机械共混物。     

Thermoplastic elastomeric blend of nitrile rubber and poly(styrene‐co‐acrylonitrile). I. Effect of mixing sequence and dynamic vulcanization on mechanical properties

The effects of dynamic vulcanization and blend ratios on mechanical properties and morphology of thermoplastic elastomeric (TPE) compositions, based on blends of nitrile rubber (NBR) and poly(styrene‐co‐acrylonitrile) (SAN), were studied. The TPE composition prepared by adding a rubber‐curatives masterbatch to softened SAN yields higher mechanical properties than that prepared by adding curatives to the softened plastic–rubber preblend. The blends having a higher rubber–plastic ratio (60 : 40 to 80 : 20) display thermoplastic elastomeric behavior, whereas those having a higher plastic–rubber ratio (50 : 50 to 90 : 10) display the behavior of impact‐resistant plastics. DSC studies revealed that NBR and SAN are thermodynamically immiscible. SEM studies of the thermoplastic elastomeric compositions show that SAN forms the matrix in which fine particles of NBR form the dispersed phase. It was further confirmed by dynamic mechanical thermal analysis. Dynamic vulcanization causes a decrease in the size of dispersed particles and improvement in mechanical properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1976–1987, 2003     

Thermoplastic dynamic vulcanisates containing LDPE,rubber, and thermochemically reclaimed ground tyre rubber

Abstract

Thermochemically devulcanised ground tyre rubber (GTR^DL) was added to fresh rubber compositions, which were then melt blended with low density polyethylene (LDPE). Styrene/butadiene rubber (SBR), natural (NR), and ethylene/propylene/diene (EPDM) rubbers were selected as the fresh rubbers. During blending, dynamic curing was achieved using sulphuric, phenolic, and peroxide curing agents. Some of the GTR was decomposed in the presence of 6 phr Regen^TM Agent-S reclaiming compound before being incorporated into the blends. The resulting thermoplastic dynamic vulcanisates had constant compositions, namely LDPE/rubber/GTR=50:25:25. Sulphuric and phenolic curing agents proved to be most suitable for dynamic curing. The thermoplastic dynamic vulcanisates with the best mechanical performance contained SBR and EPDM rubbers. The observed improvements in mechanical performance were attributed to chain entanglement and co-crosslinking in the interphase between the GTR^DL particles and the surrounding matrix (i.e. with the fresh rubber and/or LDPE). The phase morphology, which was assessed using scanning electron microscopy on the etched surfaces of cryogenically fractured thermoplastic dynamic vulcanisate compositions, is discussed.