Effects of samarium content on microstructure and mechanical properties of Mg–0.5Zn–0.5Zr alloy

Effects of samarium (Sm) content (0, 2.0, 3.5, 5.0, 6.5 wt%) on microstructure and mechanical properties of Mg–0.5Zn–0.5 Zr alloy under as-cast and as-extruded states were thoroughly investigated. Results indicate that grains of the as-cast alloys are gradually refined as Sm content increases. The dominant intermetallic phase changes from Mg₃Sm to Mg₄₁Sm₅ till Sm content exceeds 5.0 wt%. The dynamically precipitated intermetallic phase during hot-extrusion in all Sm-containing alloys is Mg₃Sm. The intermetallic particles induced by Sm addition could act as heterogeneous nucleation sites for dynamic recrystallization during hot extrusion. They promoted dynamic recrystallization via the particle stimulated nucleation mechanism, and resulted in weakening the basal texture in the as-extruded alloys. Sm addition can significantly enhance the strength of the as-extruded Mg–0.5Zn–0.5 Zr alloy at room temperature, with the optimal dosage of 3.5 wt%. The optimal yield strength (YS) and ultimate tensile strength (UTS) are 368 MPa and 383 MPa, which were enhanced by approximately 23.1% and 20.8% compared with the Sm-free alloy, respectively. Based on microstructural analysis, the dominant strengthening mechanisms are revealed to be grain boundary strengthening and dispersion strengthening.     

Effects of Cu content on microstructure and mechanical properties of Al–14.5Si–0.5Mg alloy

This study elucidates how Cu content affects the microstructure and mechanical properties of Al–14.5Si–0.5Mg alloy, by adding 4.65 wt.% and 0.52 wt.% Cu. Different Fe-bearing phases were found in the two alloys. The acicular β-Al₅FeSi was found only in the high-Cu alloy. In the low-Cu alloy, Al₈Mg₃FeSi₆ was the Fe-bearing phase. Tensile testing indicated that the low-Cu alloy containing Al₈Mg₃FeSi₆ had higher UTS and elongation than the high-Cu alloy containing the acicular β-Al₅FeSi. It is believed that the presence of the acicular β-Al₅FeSi in the high-Cu alloy increased the number of crack initiators and brittleness of the alloy. Increasing Cu content in the Al–14.5Si–0.5Mg alloy also promoted solution hardening and precipitation hardening under as-quenched and aging conditions, respectively. The hardness of the high-Cu alloy therefore exceeded that of low-Cu alloy.     

Influence of equal channel angular extrusion processing parameters on the microstructure and mechanical properties of Mg–Al–Y–Zn alloy

An as-cast Mg–Al–Y–Zn alloy was successfully processed by equal channel angular extrusion (ECAE) in the temperature range of 225–400 °C, and the influences of processing temperature on the microstructure and mechanical properties were investigated. The use of back pressure during one-pass ECAE of Mg–Al–Y–Zn alloy was favorable for eliminating the undeformed area in the billet. At the processing temperature below 250 °C, the microstructures were characterized by unrecrystallised structure and the precipitated phase Mg₁₇Al₁₂ was elongated along the extrusion direction. With increasing processing temperature to 350 °C, a large number of recrystallised grains were obtained. Increasing processing temperature promoted workability but led to decrease in the strength of Mg–Al–Y–Zn alloy. Then billets of as-cast Mg–Al–Y–Zn alloy were extruded at different numbers of ECAE passes. It was found that the microstructure was effectively refined by ECAE and mechanical properties were improved with numbers of ECAE passes increasing from one-pass to four passes. However, strengths decreased slightly after five passes though the grain size decreased considerably.     

Effects of Ca on microstructure, mechanical and corrosion properties and biocompatibility of Mg–Zn–Ca alloys

Zn and Ca were selected as alloying elements to develop an Mg–Zn–Ca alloy system for biomedical application due to their good biocompatibility. The effects of Ca on the microstructure, mechanical and corrosion properties as well as the biocompatibility of the as-cast Mg–Zn–Ca alloys were studied. Results indicate that the microstructure of Mg–Zn–Ca alloys typically consists of primary α-Mg matrix and Ca₂Mg₆Zn₃/Mg₂Ca intermetallic phase mainly distributed along grain boundary. The yield strength of Mg–Zn–Ca alloy increased slightly with the increase of Ca content, whilst its tensile strength increased at first and then decreased. Corrosion tests in the simulated body fluid revealed that the addition of Ca is detrimental to corrosion resistance due to the micro-galvanic corrosion acceleration. In vitro hemolysis and cytotoxicity assessment disclose that Mg–5Zn–1.0Ca alloy has suitable biocompatibility.     

Effect of Al on the microstructure and mechanical properties of Mg–6Zn–2Sn–0.5Mn alloy

The microstructure and mechanical properties of Mg–6Zn–2Sn–0.5Mn–xAl (x?=?0, 1, 2, 3) alloy are investigated. The addition of Al leads to the refinement of grain size and the formation of Al₆Mn, Mg₃₂(Al,Zn)₄₉ also forms when the amount of Al is higher than 2?wt-%. Because of the addition of Al, the precipitates in the alloy after ageing treatment are refined. The alloy containing 1?wt-% Al shows good mechanical properties in the as-cast state which is attributed to the refined grains and low volume fraction of large second phases, it also shows high strength after ageing treatment resulted mainly from the homogeneously distributed fine precipitates, the yield strength, ultimate tensile strength and elongation are 183, 310?MPa and 11%, respectively.     

Effects of Sn on microstructure and mechanical properties of as-rolled Mg–5Zn–1Mn alloy

Effects of Sn on microstructure and mechanical properties of Mg–5Zn–1Mn alloy subjected to high strain rate rolling (9.1?s^-1), 300°C and 80% pass reduction are investigated. With higher Sn content, the dynamic recrystallisation (DRX) grain size gradually decreases due to the stronger pinning of nano-scale precipitates at grain boundaries and the DRX fraction first increases due to the enhanced effect on DRX by decreasing stacking fault energy and then decreases due to more precipitates at grain boundaries. Ultimate tensile strength (UTS) and elongation to rupture (Er) of as-rolled alloys increase and then decrease. Alloy with 0.9 mass% Sn exhibits the highest DRX fraction (95?vol.-%), the finer DRX grain size (1.22?µm), UTS of 358?MPa and Er of 20.4%.     

Effects of trace Er addition on the microstructure and mechanical properties of Mg–Zn–Zr alloy

The effects of trace Er addition on the microstructure in Mg–9Zn–0.6Zr alloy during casting, homogenization, pre-heating, and hot extrusion processes were examined. The mechanical properties of alloys with and without Er were compared. The results showed that Er exhibited a lower solubility in solid magnesium and formed thermally stable Er- and Zn-bearing compounds. The Er-bearing alloy exhibited a considerably improved deformability, as well as a fine and uniform microstructure. Moreover, dynamic precipitation of fine MgZn₂ particles with a modified spherical morphology occurred during hot extrusion, resulting in a tensile yield strength of 313 MPa and a high elongation to failure value of 22%. Further aging of the Er-bearing alloy led to an increment of another 30 MPa in yield strength. In addition, Er markedly increased the thermal stability of the alloy structure.     

Effects of solution treatment on the microstructure and mechanical properties of Al–Cu–Mg–Ag alloy

The effects of solution treatment on the microstructure and mechanical properties of Al–Cu–Mg–Ag alloy were studied by optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), differential scanning calorimeter (DSC), transmission electron microscopy (TEM) and tensile test, respectively. The results show that the mechanical property increases and then decreases with increasing the solution temperature. And the residual phases are dissolved into the matrix gradually, the number fraction of the precipitation and the size of recrystallized grains increase. Compared to the solution temperature, the solution holding time has less effect on the microstructure and the mechanical properties of Al–Cu–Mg–Ag alloy. The overburnt temperature of Al–Cu–Mg–Ag alloy is 525 °C. The yield strength and the elongation get the best when the alloy is solution treated at 515 °C for 1.5 h, is 504 MPa and 12.2% respectively. The fracture mechanism of the samples is ductile fracture.     

Effect of cooling aging on microstructure and mechanical properties of an Al–Zn–Mg–Cu alloy

In the present work, Al–Zn–Mg–Cu alloy was aged by non-isothermal cooling aging treatment (CAT). At high initial aging temperature (IAT), the hardness was decreased with the decreased cooling rate. However, when IAT was lower than 180 °C, the hardness was increased with the decreased cooling rate. Conductivity was increased with the decreased cooling rate regardless of IAT. The tensile strength, yield strength and conductivity of Al alloy after (200–100 °C, 80 °C/h) CAT were increased 2.9%, 8.1% and 8.3% than that after T6 treatment, respectively. With an increase of IAT and decrease of cooling rate, the fine GP zone and η′ phase were transformed to be larger η′ and η precipitates. Moreover, continuous η phase at grain boundary was also grown to be individual large precipitates. Cooling aging time was decreased about 90% than that for T6 treatment, indicating cooling aging could improve the mechanical properties, corrosion resistance and production efficiency with less energy consumption.     

Effects of Zn on microstructure,mechanical properties and corrosion behavior of Mg–Zn alloys

In this study, binary Mg–Zn alloys were fabricated with high-purity raw materials and by a clean melting process. The effects of Zn on the microstructure, mechanical property and corrosion behavior of the as-cast Mg–Zn alloys were studied using direct observations, tensile testing, immersion tests and electrochemical evaluations. Results indicate that the microstructure of Mg–Zn alloys typically consists of primary α-Mg matrix and MgZn intermetallic phase mainly distributed along grain boundary. The improvement in mechanical performances for Mg–Zn alloys with Zn content until 5% of weight is corresponding to fine grain strengthening, solid solution strengthening and second phase strengthening. Polarization test has shown the beneficial effect of Zn element on the formation of a protective film on the surface of alloys. Mg–5Zn alloy exhibits the best anti-corrosion property. However, further increase of Zn content until 7% of weight deteriorates the corrosion rate which is driven by galvanic couple effect.     

Effect of processing parameters on the microstructure and mechanical properties of Al–steel composite foam

Al–steel composite foams comprise of steel hollow spheres embedded in an aluminum matrix and are processed using a gravity casting technique. The effect of processing parameters such as casting temperature and cooling rate on the microstructure and mechanical behavior was studied to establish structure–property relationships. Results show that the amount and composition of intermetallic phases present in the foam microstructure is directly related to casting temperature and cooling rate. Highest strength and energy absorption were obtained from Al–steel foams with fast solidification rates that minimize the growth of intermetallic phases.     

Effects of zirconium addition on as-cast microstructure and mechanical properties of Mg–3Sn–2Ca magnesium alloy

At present, the mechanical properties of the Mg–3Sn–2Ca magnesium alloy are not satisfying and further enhance needs to be considered via further alloying/microalloying additions. The effects of Zr addition on the as-cast microstructure and mechanical properties of the alloy were investigated by using optical and electron microscopies, differential scanning calorimetry (DSC) analysis, and tensile and creep tests. The results indicate that adding 0.41, 0.76 or 1.18 wt.% Zr can refine the grains of the alloy, and the primary CaMgSn phases in the Zr-containing alloys are changed from coarse needle-like net to relatively fine short block and/or particle-like shapes. As a result, the tensile and/or creep properties of the Zr-containing alloys are improved. Among the Zr-containing alloys, the alloy with the addition of 0.76 wt.% Zr exhibits the relatively optimum mechanical properties.     

Effects of yttrium and heat treatment on the microstructure and tensile properties of Al–7.5Si–0.5Mg alloy

The effects of yttrium (Y) additions (0, 0.1, and 0.3 wt.%) and T6 heat treatment on the microstructure and tensile properties of Al–7.5Si–0.5Mg alloy have been investigated in the present work. The microstructures and fracture surfaces of as-cast and heat treated samples were examined by scanning electron microscopy (SEM). It was found that Y modified the eutectic silicon from a coarse plate-like and acicular structure to a fine branched and some fibrous one with a better uniform distribution. In addition, T6 heat treatment played a crucial role in the fragmentation and spheroidization of eutectic silicon, especially in the well modified alloys. The tensile properties were improved by the addition of Y followed by the T6 heat treatment, and a good combination of ultimate tensile strength (353 MPa), yield strength (287 MPa) and elongation (12.1%) was obtained when the Y addition was 0.3 wt.%. Furthermore, fractographic examinations revealed that dimple-like mechanism was responsible for ductile fracture.     

Non-isothermal aging of a high-Zn-containing Al–Zn–Mg–Cu alloy: microstructure and mechanical properties

The non-isothermal aging behaviour of a newly developed Al–Zn–Mg–Cu alloy containing 17?wt-% Zn was investigated. Hardness and shear punch tests demonstrated that during non-isothermal aging, the mechanical properties of the alloy first increased and then decreased. The best properties were obtained in a sample which was non-isothermally aged upto 250°C with heating rate of 20°C?min^?1, due to the presence of η′/η (MgZn₂) phases. This was confirmed by differential scanning calorimetery. After homogenisation, residual eutectic phases remained at triple junctions or in a spherical form. During aging, these phases transformed into rodlike S (Al₂CuMg)-phase at 400°C, with sizes ranging from 50 to 250?nm. The precipitation sequence in this high-Zn alloy was similar to that for conventional Al–Zn–Mg–Cu alloys.     

Influence of Sc and Zr additions on microstructure and properties evolution of Al–Zn–Mg alloy

Journal of Materials Science - In this study, the effects of different Sc?+?Zr compound addition on the tensile properties, impact toughness, stress corrosion cracking (SCC) properties,...     

The influences of rare earth content on the microstructure and mechanical properties of Mg–7Zn–5Al alloy

The influences of rare earth (RE) on the microstructure and mechanical properties of Mg–7Zn–5Al alloy were studied. The results indicate that both the dendrite and grain size of the alloy can be refined by low RE addition. The Al₂REZn₂ phase will be formed with increasing the RE content, however the high RE addition results in the grain coarsening in the alloy due to the decrease of the contribution of Al and Zn solutes on the grain refinement. The strengthening and weakening mechanisms caused by RE addition only lead to the obviously improve on the room temperature ultimate tensile strength. The mechanical properties of the studied alloys can be improved by aging treatment, and the aged Mg–7Zn–5Al–2RE alloy exhibits optimal mechanical properties at room temperature.     

Effects of heat treatment on microstructure and mechanical properties of twin roll casted Al–5.5Mg–0.02Ti alloy

In the present investigation the Al–5.5Mg–0.02Ti alloy produced by twin roll casting (TRC) process (varying rolling speed, i.e., 3, 4, and 5 rpm) has been subjected to heat treatment for microstructure modification. Grain coarsening at the center of the strip has been observed during heat treatment process. Homogeneous microstructure of the alloys has been achieved by heat treatment process, and it has been found that the time to achieve homogeneous structure depends on the rolling speed. Transmission electron microscope (TEM) studies revealed that undesired Mg rich phase (Mg₅Al₈) has been successfully eliminated by heat treatment process. Fine and equi-axed grains in the alloys obtained by heat treatment process shows high strength and elongation.     

Microstructure and mechanical properties of variable-plane-rolled Mg–3Al–1Zn alloy

A flawless bulk AZ31 magnesium alloy with extensive mechanical twins was produced by variable-plane rolling, in which the sample was rotated 90° around its longitudinal axis between passes. The unique orientation relationship between the parent grains and the twin grains favours twinning during variable-plane rolling, which leads to the formation of extensive twins. Tensile testing revealed an excellent balance of mechanical properties, with a yield strength of 280 MPa and 15.5% elongation to failure. The significant strengthening originates from the effective blockage of glide dislocations by numerous conventional grain boundaries and twin boundaries. A weak double-peak (slightly off-basal) texture is formed during variable-plane rolling, which helps in achieving the desired level of ductility.     

Effects of yttrium and zinc addition on the microstructure and mechanical properties of Mg–Y–Zn alloys

The effects of the yttrium and zinc additions on microstructure and mechanical properties of Mg–Y–Zn alloys were investigated. It was found that the addition of yttrium increases the eutectic temperature of Mg–Y–Zn alloys greatly. The addition of yttrium can also greatly increase the dynamic recrystallization (DRX) temperature of Mg–Y–Zn alloys. The volume fraction of DRX grains in Mg₉₇Y₂Zn₁ alloy is larger than that in Mg₉₆Y₃Zn₁ alloy but smaller than that in Mg_95.5Y₃Zn_1.5 alloy due to the effects of yttrium and zinc addition. The long period stacking (LPS) structures of 18R and 14H were observed in Mg–Y–Zn alloys. The increase in the yttrium content results in increase in strength and decrease in elongation in Mg–Y–Zn alloys. The increase in both yttrium and zinc contents results in increase in both strength and elongation in Mg–Y–Zn alloys. The high strengths of the alloys were thought due to the strengthening by the grain refinement, solid solution strengthening, strain strengthening, high density of plane faults of the LPS structures, and distribution of fine Mg₂₄Y₅ phase.