Tailoring Carbon Fiber/Carbon Nanotubes Interface to Optimize Mechanical Properties of Cf‐CNTs/SiC Composites

C_f/SiC composites were fabricated using fiber coatings including CNTs and matrix infiltration using the polymer impregnation and pyrolysis process. Interface between fiber and CNTs (CF/CNTs) was tailored to optimize mechanical properties of hybrid composites. The tailored interphases, such as Pyrocarbon (PyC) and PyC/SiC, protect fibers from degradation during the growth of CNTs successfully. Hybrid composites with well‐tailored CF/CNTs interface displayed significantly increased mechanical strength (352 ± 21 MPa) compared with that (34 ± 3 MPa) of composites reinforced with CNTs, which grown on carbon fibers directly. The interfacial bonding strength of hybrid composites was improved and optimized by tailoring the CF/CNTs interface. Interfacial failure modes were studied, and a firm interface bonding at the joint where CNTs grown was observed.     

The mechanical,thermophysical and electromagnetic properties of UD SiCf/SiC composites in different directions

Unidirectional (UD) silicon carbide (SiC) fiber-reinforced SiC matrix (UD SiC_f/SiC) composites with CVI BN interphase were fabricated by polymer infiltration-pyrolysis (PIP) process. The effects of the anisotropic distribution of SiC fibers on the mechanical properties, thermophysical properties and electromagnetic properties of UD SiC_f/SiC composites in different directions were studied. In the direction parallel to the axial direction of SiC fibers, SiC fibers bear the load and BN interphase ensures the interface debonding, so the flexural strength and the fracture toughness of the UD SiC_f/SiC composites are 813.0 ± 32.4 MPa and 26.1 ± 2.9 MPa·m^1/2, respectively. In the direction perpendicular to the axial direction of SiC fibers, SiC fibers cannot bear the load and the low interfacial bonding strengths between SiC fiber/BN interphase (F/I) and BN interphase/SiC matrix (I/M) both decrease the matrix cracking stress, so the corresponding values are 36.6 ± 6.9 MPa and 0.9 ± 0.5 MPa?m^1/2, respectively. The thermal expansion behaviors of UD SiC_f/SiC composites are similar to those of SiC fibers in the direction parallel to the axial direction of SiC fibers, and are similiar to those of SiC matrix in the direction perpendicular to the axial direction of SiC fibers. The total electromagnetic shielding effectiveness (EM SE_T) of UD SiC_f/SiC composites attains 32 dB and 29 dB when the axial direction of SiC fibers is perpendicular and parallel to the electric field direction, respectively. The difference of conductivity in different directions is the main reason causing the different SE_T. And the dominant electromagnetic interference (EMI) shielding mechanism is absorption for both studied directions.     

Effect of interface types on the heat-resistance of Cansas-II SiCf /SiC composites

The heat-resistance of the Cansas-II SiC/CVI-SiC mini-composites with a PyC and BN interface was studied in detail. The interfacial shear strength of the SiC/PyC/SiC mini-composites decreased from 15 MPa to 3 MPa after the heat treatment at 1500 °C for 50 h, while that of the SiC/BN/SiC mini-composites decreased from 248 MPa to 1 MPa, which could be mainly attributed to the improvement of the crystallization degree of the interface and the decomposition of the matrix. Aside from the above reasons, the larger declined fraction of the interfacial shear strength of the SiC/BN/SiC mini-composites might also be related to the gaps in the BN interface induced by the volatilization of B₂O₃·SiO₂ phase, leading to a significant larger declined fraction of the tensile strength of the SiC/BN/SiC mini-composites due to the obvious expansion of the critical flaws on the fiber surface. Therefore, compared with the CVI BN interface, the CVI PyC interface has better heat-resistance at high temperatures up to 1500 °C due to the fewer impurities in PyC.     

Oxidation of SiC/BN/SiC ceramic matrix composites in dry and wet oxygen at intermediate temperatures

The oxidation behavior of SiC/BN/SiC ceramic matrix composites (CMCs) was evaluated from 400° to 800 °C in 100% O₂ and 50% H₂O/50% O₂ gas mixtures. Thermogravimetric analysis (TGA) was utilized to measure weight change during controlled environment exposures at elevated temperatures for 1 and 50 hours. Oxidized CMCs and their oxides were studied post-exposure with scanning electron microscopy and energy dispersive spectroscopy. The oxidation onset and composition transition temperatures were evaluated. Key observations include oxide composition, oxide wetting, oxygen solubility in Hi-Nicalon SiC fibers and BN fiber coating oxidation and volatility behavior as a function of temperature. Degradation in wet environments at 600 °C was most extensive due to the formation of a non-wetting, non-protective surface oxide, allowing oxidant access to the BN fiber coatings followed by oxidation and volatilization. Implications of the CMC oxidation behavior are discussed for CMCs in service.     

Toughened ZrB2-based ceramics through SiC whisker or SiC chopped fiber additions

In order to improve the fracture toughness, SiC whiskers or SiC chopped fibers were added to a ZrB₂ matrix in volumetric fraction of 10 and 20 vol.%. The composites were hot-pressed between 1650 and 1730 °C and their final relative densities were higher than 95%. Even at the lowest sintering temperature, the whiskers showed an evident degradation. On the other hand, the fibers maintained their initial shape and a strong interface formed between matrix and reinforcement. The fracture toughness of the composites increased from 30 to 50% compared to the baseline material, with the fibers showing a slightly higher toughening effect. In the whiskers-reinforced composites, the room-temperature strength increased when 10 vol.% whiskers were added. In the fibers-reinforced composites, the room-temperature strength decreased regardless the amount of fibers added. The high-temperature strength of the composites was higher than that of the baseline material for both types of reinforcement.     

Microstructure and mechanical properties of quasi-isotropic chopped fiber-reinforced PyC–SiC matrix composite prepared by novel nondamaging method

In this work, quasi-isotropic chopped carbon fiber-reinforced pyrolytic carbon and silicon carbide matrix (C_f/C–SiC) composites and chopped silicon carbide fiber-reinforced silicon carbide matrix (SiC_f/SiC) composites were prepared via novel nondamaging method, namely airlaid process combined with chemical vapor infiltration. Both composites exhibit random fiber distribution and homogeneous pore size. Young's modulus of highly textured pyrolytic carbon (PyC) matrix is 23.01 ± 1.43 GPa, and that of SiC matrix composed of columnar crystals is 305.8 ± 9.49 GPa in C_f/C–SiC composites. Tensile strength and interlaminar shear strength of C_f/C–SiC composites are 52.56 ± 4.81 and 98.16 ± 24.62 MPa, respectively, which are both higher than those of SiC_f/SiC composites because of appropriate interfacial shear strength and introduction of low-modulus and highly textured PyC matrix. Excellent mechanical properties of C_f/C–SiC composites, particularly regarding interlaminar shear strength, are due to their quasi-isotropic structure, interfacial debonding, interfacial sliding, and crack deflection. In addition to the occurrence of crack deflection at the fiber/matrix interface, crack deflection in C_f/C–SiC composites takes also place at the interface between PyC–SiC composite matrix and the interlamination of multilayered PyC matrix. Outstanding mechanical properties of as-prepared C_f/C–SiC composites render them potential candidates for application as thermal structure materials under complex stress conditions.     

Microstructure and tensile behavior of (BN/SiC)n coated SiC fibers and SiC/SiC minicomposites

Interphase plays an important role in the mechanical behavior of SiC/SiC ceramic-matrix composites (CMCs). In this paper, the microstructure and tensile behavior of multilayered (BN/SiC)_n coated SiC fiber and SiC/SiC minicomposites were investigated. The surface roughness of the original SiC fiber and SiC fiber deposited with multilayered (BN/SiC), (BN/SiC)₂, and (BN/SiC)₄ (BN/SiC)₈ interphase was analyzed through the scanning electronic microscope (SEM) and atomic force microscope (AFM) and X-ray diffraction (XRD) analysis. Monotonic tensile experiments were conducted for original SiC fiber, SiC fiber with different multilayered (BN/SiC)_n interfaces, and SiC/SiC minicomposites. Considering multiple damage mechanisms, e.g., matrix cracking, interface debonding, and fibers failure, a damage-based micromechanical constitutive model was developed to predict the tensile stress-strain response curves. Multiple damage parameters (e.g., matrix cracking stress, saturation matrix crack stress, tensile strength and failure strain, and composite’s tangent modulus) were used to characterize the tensile damage behavior in SiC/SiC minicomposites. Effects of multilayered interphase on the interface shear stress, fiber characteristic strength, tensile damage and fracture behavior, and strength distribution in SiC/SiC minicomposites were analyzed. The deposited multilayered (BN/SiC)_n interphase protected the SiC fiber and increased the interface shear stress, fiber characteristic strength, leading to the higher matrix cracking stress, saturation matrix cracking stress, tensile strength and fracture strain.     

Fabrication of C/C-SiC composites using high-char-yield resin

Carbon fiber reinforced ceramic matrix composites (C/C-SiC composites) were fabricated using a type of high-char-yield phenolic resin with the char yield of 81.17 wt.%. Firstly, the fabric prepreg was prepared by spreading the phenolic resin solution onto the two dimensional carbon fiber plain weave fabric and dried consequently. Afterward, the resin was cured and then the carbon fiber reinforced polymer (CFRP) was pyrolyzed to get amorphous carbon. Finally, C/C-SiC composites were obtained through liquid silicon infiltration (LSI) process. SEM micrographs showed that the Si/SiC area was homogeneously dispersed in the matrix, and during the siliconization process, a layer of SiC was formed along the surface of carbon fibers or carbon matrix. The fiber volume of CFRP was about 40 vol.%, which was much lower than other studies. XRD result indicated that only β-SiC type was formed. The result of X-ray computed tomography clearly showed the structure changes before and after the melt infiltration process. Mechanical property test showed that the composites had fracture strength of 186 ± 23 MPa, and a flexural modulus of 106 ± 8 GPa.     

Insights into internal oxidation of SiC/BN/SiC composites

The article presents new observations of the physical manifestations of internal oxidation and volatilization in SiC/BN/SiC composites. The observations are made on both unbroken and broken minicomposite specimens before and after 12 h exposures at 1000°C in dry air with 10 ppm water vapor. The observations are enabled by a sample preparation method involving ion-mill sectioning and polishing. Complementary analyses of volatilization and closure of resulting gaps are also presented. The observations show that BN is generally consumed in two stages: (i) through reaction with oxygen along the interfaces with both the fiber and the matrix, producing two concentric annular pockets of borosilicate glass and an intervening annulus of progressively thinning BN; and (ii) subsequent volatilization, through the reaction of boria with trace amounts of water vapor in the environment to form borohydroxide gases. The spatial extent to which these processes proceed is governed by a competition between the outward diffusion of reaction gases through both matrix cracks and interface gaps produced by boria volatilization, and the formation of oxides on the newly exposed surfaces of fibers, matrix, and coating.     

Stressed-oxidation behavior of 2D CVI SiC/BN/SiC at elevated temperature in air

The stressed-oxidation behaviors of 2D woven SiCf/BN/SiC composites were investigated at 950 °C and 1100 °C in air. The different proportions (60%–90%) of the ultimate tensile strength (UTS) at corresponding temperatures were chosen as constant stress. The stressed-oxidation experiments were taken to failure or interrupted (240h). The UTS decreases by 20.75% at 950 °C and 30.71% at 1100 °C. The composites did not fail during stressed oxidation when subjected to constant stress corresponding to the initial linear and the beginning of nonlinear segments of the tensile curve, above which the composites failed with a maximum failure life of about 10h. Fiber degradation due to the thermal exposure and the fiber cracks caused by the oxidation of BN interface coating and SiC fiber could be responsible for the strength degradation and failure of the composites during stressed oxidation.     

Fabrication and properties of SiCnw-reinforced SiC composites by reactive melt infiltration with BN and PyC interface

To tailor the fiber–matrix interface of SiC nanowires-reinforced SiC (SiC_nw/SiC) ceramic matrix composites (CMCs) for improved mechanical properties, SiC nanowires were coated with BN and pyrolytic carbon (PyC) compound coatings prepared by the dip-coating process in boric acid and urea solution and the pyrolysis of phenolic resin. SiC_nw/SiC CMC with PyC/BN interfaces were fabricated by reactive melt infiltration (RMI) at 1680°C for 1 h. The influences of phenolic resin content on the microstructure and mechanical properties of the CMC were investigated. The results showed that the flexural strength and fracture toughness reach the maximum values of 294 MPa and 4.74 MPa m^1/2 as the phenolic resin content was 16 and 12 wt%, respectively. The displacement–load curve of the sample exhibited a gradient drop with increasing phenolic resin content up to 12 wt%. The results demonstrated that the PyC/BN compound coatings could play the role of protecting the SiC_nw from degradation as well as improving the more moderate interfacial bonding strengths during the RMI.     

Effect of short carbon fiber content on the mechanical properties of TiB2-based composites prepared by spark plasma sintering

In this study, TiB₂-30 vol% SiC composites containing 0, 5, 10, and 15 vol% short carbon fibers (C_f) were produced by spark plasma sintering (SPS). The effect of carbon fiber content on microstructure, density, and mechanical properties (micro-hardness and flexural strength) of the fabricated composites was studied. Scanning electron microscopy (SEM) results indicated that the fibers were uniformly dispersed in the TiB₂–SiC matrix using wet ball milling before SPS process. Fully dense TiB₂–SiC–C_f composites were achieved by SPS process at 1900°C for 10 min under 30 MPa. With the addition of fibers, the relative density of the composites did not change considerably. Mechanical tests revealed that microhardness was reduced about 19% by the incorporation of carbon fibers, whereas the flexural strength improved significantly. However, the flexural strength diminished by adding carbon fibers above to critical value (5 vol%) due to residual thermal stresses, nonhomogeneous structure and graphitization of carbon fibers. It was found that the composite with 5 vol% C_f had the highest flexural strength (482 MPa), which was enhanced by 20% compared with the TiB₂–SiC composite.     

Effects of in-situ carbon layer and volume fraction of SiC fiber on the mechanical properties and fracture behaviors of SiCf/SiC composites fabricated by a modified PIP method

Unidirectional SiC_f/SiC composites (UD SiC_f/SiC composites) with excellent mechanical properties were successfully fabricated by a modified PIP method which involved the preparation of film-like matrix containing carbon layer with a low concentration PCS solution followed by the rapid densification of composites with a high concentration PCS solution. Carbon layers were in-situ formed and alternating with SiC layers in the as-received matrix. The unique microstructure endows the composites with appropriate interfacial bonding state, good load transfer ability of interphase and matrix and load bearing ability of fiber, and great crack deflection capacity, which ensures the synergy of high strength and toughness of composites. It is also found that the fiber volume fraction in the preform makes a non-negligible effect on the distribution of interphase and matrix, of which the reasonable adjustment can be utilized to optimize the mechanical properties of composites. Compared with the composites only using high concentration PCS solution, the UD SiC_f/SiC composites prepared by the modified PIP method exhibit superior mechanical properties. Ultrahigh flexural strength of 1318.5 ± 158.3 MPa and fracture toughness of 47.6 ± 5.6 MPa·m^1/2 were achieved at the fiber volume fraction of 30%.     

Preparation of SiC/SiC composites with high toughness by reaction of the SiCP+C double-cladding layer with liquid silicon

SiC/SiC composites prepared by liquid silicon infiltration (LSI) have the advantages of high densification, matrix cracking stress and ultimate tensile strength, but the toughness is usually insufficient. Relieving the residual microstress in fiber and interphase, dissipating crack propagation energy, and improving the crystallization degree of interphase can effectively increase the toughness of the composites. In this work, a special SiC particles and C (SiC_P +C) double-cladding layer is designed and prepared via the infiltration of SiC_P slurry and chemical vapor infiltration (CVI) of C in the porous SiC/SiC composites prepared by CVI. After LSI, the SiC generated by the reaction of C with molten Si combines with the SiC_P to form a layered structure matrix, which can effectually relieve residual microstress in fiber and interphase and dissipate crack propagation energy. The crystallization degree of BN interphase is increased under the effects of C-Si reaction exotherm. The as-received SiC/SiC composites possess a density of 2.64 g/cm³ and a porosity of 6.1%. The flexural strength of the SiC/SiC composites with layered structure matrix and highly crystalline BN interphase is 577 MPa, and the fracture toughness reaches up to 37 MPa·m^1/2. The microstructure and properties of four groups of SiC/SiC composites prepared by different processes are also investigated and compared to demonstrate the effectiveness of the SiC_P +C double-cladding layer design, which offers a strategy for developing the SiC/SiC composites with high performance.     

Fatigue of three advanced SiC/SiC ceramic matrix composites at 1200°C in air and in steam

High‐temperature mechanical properties and tension‐tension fatigue behavior of three advanced SiC/SiC composites are discussed. The effects of steam on high‐temperature fatigue performance of the ceramic‐matrix composites are evaluated. The three composites consist of a SiC matrix reinforced with laminated, woven SiC (Hi‐Nicalon?) fibers. Composite 1 was processed by chemical vapor infiltration (CVI) of SiC into the Hi‐Nicalon? fiber preforms coated with boron nitride (BN) fiber coating. Composite 2 had an oxidation inhibited matrix consisting of alternating layers of silicon carbide and boron carbide and was also processed by CVI. Fiber preforms had pyrolytic carbon fiber coating with boron carbon overlay applied. Composite 3 had a melt‐infiltrated (MI) matrix consolidated by combining CVI‐SiC with SiC particulate slurry and molten silicon infiltration. Fiber preforms had a CVI BN fiber coating applied. Tensile stress‐strain behavior of the three composites was investigated and the tensile properties measured at 1200°C. Tension‐tension fatigue behavior was studied for fatigue stresses ranging from 80 to 160 MPa in air and from 60 to 140 MPa in steam. Fatigue run‐out was defined as 2 × 10⁵ cycles. Presence of steam significantly degraded the fatigue performance of the CVI SiC/SiC composite 1 and of the MI SiC/SiC composite 3, but had little influence on the fatigue performance of the SiC/SiC composite 2 with the oxidation inhibited matrix. The retained tensile properties of all specimens that achieved fatigue run‐out were characterized. Composite microstructure, as well as damage and failure mechanisms were investigated.     

Influence of precursor concentration on the densification efficiency and properties of SiC/SiC composites

The SiC/SiC composites were manufactured by polymer precursor impregnation pyrolysis process with near stoichiometric SiC fiber 2D preform as the reinforcing phase, the mixed solution of polycarbosilane (PCS), and xylene as impregnant. The effects of PCS concentration on the densification process, microstructure, and mechanical behavior of SiC/SiC composites were investigated using mechanical property testing, scanning electron microscopy, and other characterization techniques. Results showed the porosity and flexural strength of SiC/SiC composites increased first and then decreased with the increase of PCS concentration. When the concentration of PCS was 55% and 60%, the flexural strength of SiC/SiC composites reached 565.77 and 573.02 MPa, respectively. The mechanical behavior of SiC/SiC composites presented typical pseudoplastic characteristics such as fiber pulling-out, fiber bridging, and interface layer peeling, which would meet the dual requirements of optimizing the matrix and interface structure.     

Low-temperature thermally modified fir-derived biomorphic C–SiC composites prepared by sol-gel infiltration

In order to solve the problems (i.e. low infiltration efficiency, cracks, interface separation and poor mechanical properties) in the process of wood-derived C–SiC composites, the thermal modification of fir at low temperatures (300 °C ～ 350 °C) combined with sol-gel infiltration was used to successfully produce biomorphic ceramics. The prepared materials were comprehensively characterized and exhibited improved interfacial bonding between C and SiC and mechanical properties. The weight gain per unit volume (0.123 g/cm³) of SiO₂ gel in the fir thermally modified at 300 °C is 167.4%, higher than that (0.046 g/cm³) of the unmodified fir. A well-bonded interface was formed between the SiO₂ gel and the pore wall of the fir thermally modified at 300 °C. With the increase of modification temperature from 300 °C to 350 °C, the distance between SiO₂ gel and the pore wall increases, and a gap (1–3 μm) is observed between SiO₂ gel and the pore wall of the fir carbonized at 600 °C. The C–SiC composites sintered at 1400 °C exhibited the highest compressive strength and bending strength of 40.8 ± 5.8 MPa and 11.7 ± 2.1 MPa, respectively, owing to the well-bonded interface between C of fir thermally modified at 300 °C and SiC. However, the composites sintered at 1600 °C for 120 min exhibited the lowest compressive strength and bending strength of 28.1 ± 13.4 MPa and 5.7 ± 1.6 MPa, respectively, which are 31.1% and 51.3% lower than those sintered at 1400 °C for 120 min, respectively. This might result from the porous structure formed by the excessive consumption of fir-derived carbon during the reaction between C and SiO₂ at 1600 °C for 120 min. Therefore, thermal modification in the preparation of biomorphic C–SiC composites can promote slurry infiltration and the formation of a well-bonded interface between C and SiC, thus improving the mechanical properties of the composites.     

Effect of high-temperature heat treatment on the microstructure and mechanical behavior of PIP-based C/C-SiC composites with SiC filler

C/C-SiC composites were fabricated by a combined process of chemical vapor deposition (CVD), slurry infiltration(SI), and precursor infiltration and pyrolysis (PIP). The microstructure and mechanical behavior were investigated for the dense C/C-SiC composites before and after high-temperature heat treatment. The results indicated that the sintering of the SiC matrix and the migration of the SiC matrix/fiber bundles weak interface occurred after high-temperature heat treatment at 1900 ℃. The SiC sintering resulted in an increase in the flexural strength of the C/C-SiC composites from 298.9 ± 35.0 MPa to 411.1 ± 57.3 MPa. The migration of the weak interface changed the direction of crack propagation, making the fracture toughness of the C/C-SiC composites decrease from 13.3 ± 1.7 MPa⋅m ^1/2 to 9.02 ± 1.5 MPa⋅m ^1/2.     

Effects of fabrication processes on the properties of SiC/SiC composites

Precursor infiltration and pyrolysis (PIP) and chemical vapor infiltration (CVI) were used to fabricate SiC/SiC composites on a four-step 3D SiC fibre preform deposited with a pyrolytic carbon interface. The effects of fabrication processes on the microstructure and mechanical properties of the SiC/SiC composites were studied. Results showed the presence of irregular cracks in the matrix of the SiC/SiC composites prepared through PIP, and the crystal structure was amorphous. The room temperature flexural strength and modulus were 873.62 MPa and 98.16 GPa, respectively. The matrix of the SiC/SiC composites prepared through CVI was tightly bonded without cracks, the crystal structure had high crystallinity, and the room temperature bending strength and modulus were 790.79 MPa and 150.32 GPa, respectively. After heat treatment at 1300 °C for 50 h, the flexural strength and modulus retention rate of the SiC/SiC composites prepared through PIP were 50.01% and 61.87%, and those of the composites prepared through CVI were 99.24% and 96.18%, respectively. The mechanism of the evolution of the mechanical properties after heat treatment was examined, and the analysis revealed that it was caused by the different fabrication processes of the SiC matrix. After heat treatment, the SiC crystallites prepared through PIP greatly increased, and the SiOxCy in the matrix decomposed to produce volatile gases SiO and/or CO, ultimately leading to an increase in the number of cracks and porosity in the material and a decrease in the material load-bearing capacity. However, the size of the SiC crystallites prepared through CVI hardly changed, the SiC matrix was tightly bonded without cracks, and the load-bearing capacity only slightly changed.     

Influence of the SiC matrix introduction time on the microstructure and mechanical properties of Cf/Hf0.5Zr0.5C-SiC ultra-high temperature composites

C_f/Hf_0.5Zr_0.5C-SiC composites were prepared by introducing Hf_0.5Zr_0.5C matrix (11 cycles) and SiC matrix (9 cycles) into the carbon cloth preform through precursor impregnation and pyrolysis (PIP) process. The influence of the introduction time of SiC matrix on the microstructure and mechanical properties of C_f/Hf_0.5Zr_0.5C-SiC composites was studied, and the results show that with the increase of the PIP cycles of the SiC matrix introduced before Hf_0.5Zr_0.5C matrix, the composite open porosity decreased, and the flexural strength and modulus presented an obvious upward trend. CS45 sample, which has 4 cycles of PIP SiC introduced in advance, has the highest flexural strength, flexural modulus and interfacial shear strength of 402.73 ± 35.73 MPa, 56.92 ± 3.97 GPa and 100.88 ± 7.79 MPa, respectively. Hf_0.5Zr_0.5C matrix has a loose and porous structure, so when more SiC matrix was introduced in advance, its covering effect on the surface of fibers led to less intra-bundle pores and thusly denser composite structure, and due to the compactness of SiC matrix, better overall bonding of fiber, interface and matrix was achieved, as well as better load transfer effect, which led to obvious interfacial debonding and cracking based on the in-situ SEM observation during flexural tests. While in the sample without pre-introduced SiC, the cracking occurred mainly between the interface and porous matrix and the overall performance of the material was poor.