Influence of the content of polymethyl methacrylate on the properties of porous Si3N4 ceramics fabricated by digital light processing

Porous Si₃N₄ ceramics are highly regarded as ideal materials for radomes due to their unique characteristics. However, the slurry used for the preparation of porous Si₃N₄ ceramics suffers from a low cure depth, making it challenging to fabricate ceramic components using DLP technology. In this study, porous Si₃N₄ ceramics were prepared by combining DLP technology with pore-forming agent method. The addition of polymethyl methacrylate (PMMA) powders with lower refractive index than that of Si₃N₄ powders can improve the penetration depth of ultraviolet light in the Si₃N₄ slurry. A systematic study was conducted to investigate the influence of the addition of PMMA powders on the properties of Si₃N₄ slurries and porous Si₃N₄ ceramics. When PMMA powders were added at 10 wt%, the slurry with a lowest viscosity of 0.13 Pa s (the shear rate is 30 s⁻¹) and cure depth of 40.0 μm (the exposure energy is 600 mJ/cm²) was obtained. With the increase of PMMA content, porous Si₃N₄ ceramics experienced a gradual decrease in both the flexural strength and bulk density, while the porosity increased from 14.41% to 27.62%. Specifically, when 20 wt% PMMA was added, the resulting porous Si₃N₄ ceramics had a lowest bulk density (2.41 g/cm³), a maximum porosity (27.62%), and a flexural strength (435.87 MPa). The study is of great significance in establishing an experimental foundation for fabricating porous Si₃N₄ ceramics by using DLP technology.     

Microstructure and permeability of porous Si3N4 supports prepared via SHS

Porous Si₃N₄ ceramics with tailored pore structures were fabricated via self-propagating high temperature synthesis (SHS) using Polymethylmethacrylate (PMMA) as pore forming agent. The pore structures, mechanical properties and permeation performance of porous Si₃N₄ ceramics were investigated by altering the particle sizes and amount of PMMA. With the increasing content of PMMA, the flexural strength of samples decreased from 102.5 MPa to 9.4 MPa. The tortuosity which showed irregular variation affected gas permeability directly. The samples with 20 wt% content of PMMA exhibited the maximum Darcian and non-Darcian constants with the smallest tortuosity. Moreover, the comparison of permeability coefficients with other ceramics via different pore forming methods in literature was presented. The specimens exhibited great permeability due to the large pore sizes created by the elongated and coarsened β-Si₃N₄ grains during the SHS process, providing a low-cost and environmentally friendly method for preparing high permeability porous Si₃N₄ supports.     

Effect of BN content on microstructures,mechanical and dielectric properties of porous BN/Si3N4 composite ceramics prepared by gel casting

Porous BN/Si₃N₄ composite ceramics with different BN contents have been fabricated by gel casting. The rheological behaviors of the suspensions, microstructure, mechanical properties, dielectric properties and critical temperature difference of thermal shock (ΔT_C) of porous BN/Si₃N₄ composite ceramics with different BN contents were investigated. With BN contents increasing, the mechanical properties of the porous BN/Si₃N₄ composite ceramics were partially declined, but the dielectric properties and thermal shock resistances were enhanced at the same time. For the porous Si₃N₄ ceramic without BN addition, the porosity, flexural strength, dielectric constant and critical temperature difference were 48.1%, 128 MPa, 4.1 and 395 °C, while for the 10 vol% BN/Si₃N₄ porous composite ceramics, they were 49.4%, 106.6 MPa, 3.8, and 445 °C, respectively. The overall performance of the obtained porous BN/Si₃N₄ composite ceramics indicated that it could be one of the ideal candidates for high-temperature wave-transparent applications.     

Mechanical property and gas filtration behavior of porous reaction bonded Si3N4 with monodispersed PMMA as pore former

Porous Si₃N₄ ceramics were prepared by gel casting combined with a reaction bonding route using monodispersed PMMA as the pore former, and Isobam was used as a gel agent. With the PMMA addition varying from 0 to 20 wt.%, the bending strength was degraded from 94.0 to 39.1 MPa owing to the increased porosity and decreased bulk density. The β-Si₃N₄ prismatic grains and round pores introduced by the monodispersed PMMA micro balls would endow the samples with high strength, and the permeability of the resulting samples was increased obviously with the increase of PMMA addition. Flue gas filtration test exhibited that the filtration efficiency of the porous ceramics filter was not degraded with introducing of the PMMA pore former, even though the permeability was increased obviously. The block type of the sample with 20-wt.% PMMA additions during filtration was cake filtration, which indicates that the sample has the characteristic of being reusable after back-blowing in flue gas filtration applications. Porous Si₃N₄ with high strength and permeability fabricated via the reaction bonding route exhibits great potential for low-cost high-performance ceramics filters.     

A strategy for fabricating anisotropic SI3N4 ceramics with controllable mechanical and thermal properties

Heat dissipation material with programmable anisotropic property is very challenging, yet can realize the controllable thermal diffusion for heating device. In this work, anisotropic Si₃N₄ ceramics with oriented grains are prepared to adjust and improve the mechanical and thermal properties under the applied stress field by rolling film forming technology. Through the design of the sintering aids in the process of liquid-phase sintering, the orientation degree of the Si₃N₄ grains is programmable as well as the mechanical property and the thermal property of the Si₃N₄ ceramics. As a consequence, the obtained Si₃N₄ ceramics show significant anisotropy in mechanical properties and thermal conductivity. The typical fracture toughness and thermal conductivity along the grain orientation direction are 10.6 MPa⋅m^1/2 and 45.45 W/(m⋅K) while they are 4.5 MPa⋅m^1/2 and 66.42 W/(m⋅K) in the direction perpendicular to the oriented grain, respectively. This grain orientation method paves the way for the thermal performance design and the production of programmable heat dissipation material.     

Preparation of Si3N4 porous ceramics via foam-gelcasting and microwave-nitridation method

Si₃N₄ porous ceramics with improved mechanical strength were fabricated for the first time by a combined foam-gelcasting and microwave-nitridation method at 1273–1373?K. The Si₃N₄ porous samples prepared at 1373?K/20?min with the porosity of 68.9% had respectively flexural and compressive strength as high as 8.1 and 20.8?MPa, which values were comparable or even superior to those of Si₃N₄ porous ceramics prepared previously by the conventional heating technique at a much higher temperature of 1773–1973?K, indicating that present preparation strategy is feasible to prepare high quality Si₃N₄ porous ceramic at a much milder condition. Moreover, the thermal conductivity of as-prepared Si₃N₄ porous ceramics at 1073?K was as low as 1.697?W/(m?K), suggesting it could be a potentially good heat insulating material for aluminum electrolyte cells.     

Thermal conductivity of porous SiC composite ceramics derived from paper precursor

Biomorphic porous SiC composite ceramics were produced by chemical vapor infiltration and reaction (CVI-R) technique using paper precursor as template. The thermal conductivity of four samples with different composition and microstructure was investigated: (a) C-template, (b) C-SiC, (c) C-SiC–Si₃N₄ and (d) SiC coated with a thin layer of TiO₂. The SiC–Si₃N₄ composite ceramic showed enhanced oxidation resistance compared to single phase SiC. However, a key property for the application of these materials at high temperatures is their thermal conductivity. The later was determined experimentally at defined temperatures in the range 293–373 K with a laser flash apparatus. It was found that the thermal conductivity of the porous ceramic composites increases in the following order: C-template < C-SiC < C-SiC–Si₃N₄ < SiC–TiO₂. The results were interpreted in regard to the porosity and the microstructure of the ceramics.     

Si3N4-BN-SiCN ceramics with unique hetero-interfaces for enhancing microwave absorption properties

SiCN-based ceramics with broadband and strong microwave absorption properties are desired for the structural and functional integration of ceramic matrix composites. The elemental composition and thermal expansion coefficients of the ceramics matrix crucially affect its microstructure and electromagnetic wave (EMW) absorption properties. BN layer with lower electrical conductivity and higher specific area, exhibits both the impedance matching characteristic and EMW attenuation in the process of multiple reflections, electrical conductivity loss, dipole polarization and interfacial polarization. Therefore, Si₃N₄-BN-SiCN ceramics, which were synthesized using chemical vapor infiltration (CVI) method, construct unique hetero-interface of Si₃N₄-BN, Si₃N₄–SiCN and BN-SiCN. Therefore, the Si₃N₄-BN-SiCN ceramics have outstanding EMW absorption performance and realize an effective absorption bandwidth (EAB) that covers the whole X band and the minimum reflection coefficient (RC) reaches -18.43 dB at a thickness of 3.37 mm.     

Effect of in situ synthesized and additives on the thermal performance of mullite thermal storage ceramics

High-performance thermal storage ceramics can enable utilization of solar thermal power generation plants. In this work, in situ synthesis was used to prepare mullite thermal storage ceramics. Calcined bauxite, talc, and kaolin were used as raw materials. The effects of additives (e.g., SiC, Si₃N₄, TiC, and ZrB₂) on the density, mechanical durability, phase components, microstructure, and thermal performance of the mullite ceramics were studied. The results showed that the thermal expansion coefficient, thermal conductivity, and heat storage density of the mullite ceramics were affected by their phase components. SiC and Si₃N₄ did not decompose during the in situ syntheses, but TiC and ZrB₂ decomposed. With the addition of 10 wt% SiC, the thermal conductivity improved to 2.72 W (m K)^?1 (298 K). The heat storage density of this material was 688 kJ kg^?1 (273–1073 K). Consequently, the in situ synthesized mullite thermal storage ceramic with added SiC could be a promising candidate material for a compound latent-sensible heat storage system.     

Fabrication of Si3N4 ceramics substrates with high thermal conductivity by tape casting and gas pressure sintering

In this paper, high thermal conductivity Si₃N₄ ceramics were successfully fabricated through exploring and optimizing the tape casting process. The impact of various organic additives on the rheological characteristics of Si₃N₄ slurry was explored, and the pore size distribution and microstructure of the green tapes at different solid loadings were investigated, as well as the microstructure of Si₃N₄ ceramics. Green tapes with a narrow pore size distribution, a small average pore size, and a high density of 1.88 g cm⁻³ were prepared by the investigation and optimization of the Si₃N₄ slurry formulation. After gas pressure sintering, Si₃N₄ ceramics with a density of 3.23 g cm⁻³, dimensions of 78 mm × 78 mm, and a thickness of 0.55 mm were obtained. The microstructure of the Si₃N₄ ceramics showed a bimodal distribution and a low content of glassy phases. The thermal conductivity of the Si₃N₄ ceramics was 100.5 W m⁻¹ K⁻¹, the flexural strength was 735 ± 24 MPa, and the fracture toughness was 7.17 MPa m^1/2.     

Fabrication,thermal shock resistance,and dielectric property of α-Si3N4-based ceramic coating on porous Si3N4 ceramics

A dense α-Si₃N₄-based ceramic protective coating was successfully prepared on porous Si₃N₄ ceramics by a liquid infiltration and filling method. The coating composed of a primary α-Si₃N₄ phase and secondary O'-Sialon, β-Sialon, and Y–Si–Al–O–N glass phase. After thermal shock at ΔT = 1000°C for five times, cracks were produced, but the tip of crack stopped inside the coating; so the coated porous Si₃N₄ ceramics still had a good waterproof ability and its water absorption was only 7%. During thermal shock, toughening mechanisms involving needle-like O'-Sialon particle bridging, crack deflection, and rough fracture, occurred within the cracks, contributing to thermal shock resistance of the coating. The dielectric constant of the coated porous Si₃N₄ ceramics showed a slow increase trend with increasing temperature, and it reached the maximum value of 3.57 at 1100°C at the frequency of 11 GHz. The dielectric loss increased slowly as the temperature increased from room temperature to 900°C, but it started to increase evidently when the temperature was over 900°C.     

A novel aerogels/porous Si3N4 ceramics composite with high strength and improved thermal insulation property

A novel ZrO₂-SiO₂ aerogels/porous Si₃N₄ ceramics composite with high strength, low density, good dielectric properties and low thermal conductivity was synthesized by filling ZrO₂-SiO₂ aerogels into the porous Si₃N₄ ceramics through vacuum sol-impregnating. The effects of aerogels on the microstructure and properties of composite were discussed. The results show that aerogels could form a mesoporous structure and significantly decrease the thermal conductivity from 9.8 to 7.3 W m^?1 K^?1. Meanwhile, the density, mechanical and dielectric properties of the porous Si₃N₄ ceramics could not be affected after introducing ZrO₂-SiO₂ aerogels. The composite exhibits high porosity (62.6%), high flexural strength (53.86 MPa) and low dielectric constant (2.86). The ZrO₂-SiO₂ aerogels/porous Si₃N₄ ceramics composite shows great potential as radome materials applied in the fields of aerospace.     

Effect of polystyrene addition on properties of porous Si3N4 ceramics fabricated by digital light processing

Porous Si₃N₄ ceramics with high strength and high transmittance have been widely used in the field of defense and military. Additive manufacturing (AM) technology is one of the effective means to fabricate porous Si₃N₄ ceramics. Nevertheless, it is difficult to prepare porous Si₃N₄ ceramics by using digital light processing (DLP) because of the large refractive index difference between Si₃N₄ powders and photosensitive resin. In this study, the effects of the amount of polystyrene (PS) powders on the properties of Si₃N₄ ceramic slurries and sintered ceramics were systematically discussed. The addition of PS reduced the overall refractive index of powders and increased the average particle size of powders, thus improving the cure depth of Si₃N₄ ceramic slurries from 11.0 ± 2.0 μm to 55.7 ± 1.8 μm. With the increase of PS content, the shrinkage and porosity of Si₃N₄ ceramics gradually increased, and the bulk density and flexural strength showed the opposite trend. The slurry with low viscosity (2.38 Pa٠s at a shear rate of 30 s⁻¹) and high cure depth (51.2 ± 4.6 μm) was obtained when the content of PS was 15 wt%, which met the thickness requirements for printing. The total porosity of Si₃N₄ ceramics reached the maximum values at 28.21 ± 2.58%. The addition of PS solved the problem of low cure depth of slurries, and PS as a pore-forming agent could help Si₃N₄ ceramics form porous structure. This research provides valuable insights into the fabrication of non-oxide ceramics with high refractive index using DLP technology.     

Preparation,microstructure, and properties of GPS silicon nitride ceramics with β-Si3N4 seeds and nanophase additives

Si₃N₄ ceramics with high thermal conductivity and outstanding mechanical properties were prepared by adding β-Si₃N₄ seeds and nanophase α-Si₃N₄ powders as modifiers. The introduction of β-Si₃N₄ seeds enhanced the growth of β-Si₃N₄ grains. Owing to the interlocked structure induced by the β-Si₃N₄ grains, the fracture toughness of Si₃N₄ ceramics reached a high value of 7.6 MPa·m^1/2; also, the large-sized grains increased the contact possibility of Si₃N₄ grains, improving the thermal conductivity of Si₃N₄ ceramics (64 W/(m·K)). Because of the introduction of nanophase α-Si₃N₄, the flexural strength, fracture toughness, and thermal conductivity of the Si₃N₄ ceramics increased to 754 MPa, 7.2 MPa·m^1/2, and 54 W/(m·K), respectively. According to the analysis of the growth kinetics of Si₃N₄ grains, the rapid growth of Si₃N₄ grains was ascribed to the reduction in the activation energy resulting from the introduction of β-Si₃N₄ seeds and nanophase α-Si₃N₄.     

Fabrication of high thermal conductivity silicon nitride ceramics by pressureless sintering with MgO and Y2O3 as sintering additives

The fabrication of silicon nitride (Si₃N₄) ceramics with a high thermal conductivity was investigated by pressureless sintering at 1800 °C for 4 h in a nitrogen atmosphere with MgO and Y₂O₃ as sintering additives. The phase compositions, relative densities, microstructures, and thermal conductivities of the obtained Si₃N₄ ceramics were investigated systemically. It was found that at the optimal MgO/Y₂O₃ ratio of 3/6, the relative density and thermal conductivity of the obtained Si₃N₄ ceramic doped with 9 wt% sintering aids reached 98.2% and 71.51 W/(m·K), respectively. EDS element mapping showed the distributions of yttrium, magnesium and oxygen elements. The Si₃N₄ ceramics containing rod-like grains and grain boundaries were fabricated by focused ion beam technique. TEM observations revealed that magnesium existed as an amorphous phase and that yttrium produced a new secondary phase.     

Preparation of calcium hexaluminate porous ceramics by gel-casting method with polymethyl methacrylate as pore-forming agent

Calcium hexaluminate (CA₆) porous ceramics were prepared by gel-casting method, with α-Al₂O₃ and CaCO₃ as raw materials and polymethyl methacrylate (PMMA) microspheres as pore-forming agent. The effects of the amount of pore-forming agent PMMA microspheres on the phase composition, bulk density, apparent porosity, flexural strength, microstructure, thermal shock stability and thermal conductivity of CA₆ porous ceramics were systematically studied. The pores of CA₆ porous ceramics are mainly formed by the burning loss of PMMA microspheres and the decomposition of organic matter. Adding an appropriate amount of PMMA microspheres as pore-forming agent has a positive effect on the thermal shock stability of CA₆ porous ceramics. When the amount of pore-forming agent is 15 wt%, the volume density of CA₆ porous ceramics is 1.33 g/cm³, the porosity is 63%, the flexural strength is 13.9 MPa, the thermal shock times can reach 9 times, and the thermal conductivity is 0.293 W/(m·K), which can meet the application in refractory, ceramics or high temperature cement industries.     

Effect of Si addition on the mechanical and thermal properties of sintered reaction bonded silicon nitride

Advanced silicon nitride (Si₃N₄) ceramics were fabricated using a mixture of Si₃N₄ and silicon (Si) powders via conventional processing and sintering method. These Si₃N₄ ceramics with sintering additives of ZrO₂ + Gd₂O₃ + MgO were sintered at 1800 °C and 0.1 MPa in N₂ atmosphere for 2 h. The effects of added Si content on density, phases, microstructure, flexural strength, and thermal conductivity of the sintered Si₃N₄ samples were investigated in this study. The results showed that with the increase of Si content added, the density of the samples decreased from 3.39 g/cm³ to 2.92 g/cm³ except for the sample without initial Si₃N₄ powder addition, while the thermal diffusivity of the samples decreased slightly. This study suggested that addition of Si powder, which varied from 0 to 100%, in the starting materials might provide a promising route to fabricate cost-effective Si₃N₄ ceramics with a good combination of mechanical and thermal properties.     

Porous SiC–Si3N4 composite ceramics with excellent EMW absorption property prepared by gelcasting using DMAA

The porous SiC–Si₃N₄ composite ceramics with good EMW absorption properties were prepared by combination of gelcasting and carbothermal reduction. The pre-oxidation of Si₃N₄ powders significantly improved the rheological properties of slurries (0.06 Pa s at 103.92 s⁻¹) and also suppressed the generation of NH₃ and N₂ from Si₃N₄ hydrolysis and reaction between Si₃N₄ and initiator APS, thereby reducing the pore defects in green bodies and enhancing mechanical properties with a maximum value of 42.88 MPa. With the extension of oxidation time from 0 h to 10 h, the porosity and pore size of porous SiC–Si₃N₄ composite ceramics increased from approximately 41.86% and 1.0–1.5 μm to 46.33% and ~200 μm due to the production of CO, N₂ and gaseous SiO, while the sintering shrinkage decreased from 16.24% to 10.50%. With oxidation time of 2 h, the Si₂N₂O fibers formed in situ by the reaction of Si₃N₄ and amorphous SiO₂ effectively enhanced the mechanical properties, achieving the highest flexural strength of 129.37 MPa and fracture toughness of 4.25 MPa m^1/2. Compared with monolithic Si₃N₄ ceramics, the electrical conductivity, relative permittivity and dielectric loss were significantly improved by the in-situ introduced PyC from the pyrolysis of three-dimensional network DMAA-MBAM gel in green bodies and the SiC from the carbothermal reduction reaction between PyC and SiO₂ and Si₃N₄. The porous SiC–Si₃N₄ composite ceramics prepared by the unoxidized Si₃N₄ powders demonstrated the optimal EMW absorption properties with reflection loss of −22.35 dB at 8.37 GHz and 2 mm thickness, corresponding to the effective bandwidth of 8.20–9.29 GHz, displaying great application potential in EMW absorption fields.     

Effect of seeding on the thermal conductivity of self-reinforced silicon nitride

Thermal conductivity of Si₃N₄ containing large β-Si₃N₄ particles as seeds for grain growth was investigated. Seeds addition promotes growth of β-Si₃N₄ grains during sintering to develop the duplex microstructure. The thermal conductivity of the material sintered at 1900 °C improved up to 106 W m⁻¹ K⁻¹, although that of unseeded material was 77 Wm⁻¹ K⁻¹. Seeds addition leads to reduction of the sintering temperature with developing the duplex microstructure and with improving the thermal conductivity, which benefits in terms of production cost of Si₃N₄ ceramics with thermal conductivity. ©     

ZrSi2–MgO as novel additives for high thermal conductivity of β-Si3N4 ceramics

A novel ZrSi₂–MgO system was used as sintering additive for fabricating high thermal conductivity silicon nitride ceramics by gas pressure sintering at 1900°C for 12 hours. By keeping the total amount of additives at 7 mol% and adjusting the amount of ZrSi₂ in the range of 0-7 mol%, the effect of ZrSi₂ addition on sintering behaviors and thermal conductivity of silicon nitride were investigated. It was found that binary additives ZrSi₂–MgO were effective for the densification of Si₃N₄ ceramics. XRD observations demonstrated that ZrSi₂ reacted with native silica on the Si₃N₄ surface to generate ZrO₂ and β-Si₃N₄ grains. TEM and in situ dilatometry confirmed that the as formed ZrO₂ collaborated with MgO and Si₃N₄ to form Si–Zr–Mg–O–N liquid phase promoting the densification of Si₃N₄. Abnormal grain growth was promoted by in situ generated β-Si₃N₄ grains. Consequently, compared to ZrO₂-doped materials, the addition of ZrSi₂ led to enlarged grains, extremely thin grain boundary film and high contiguity of Si₃N₄–Si₃N₄ grains. Ultimately, the thermal conductivity increased by 34.6% from 84.58 to 113.91 W·(m·K)⁻¹ when ZrO₂ was substituted by ZrSi₂.