Long-term thermal stability of Li4TiO4–Li2TiO3 core–shell breeding pebbles under continuous heating in H2/Ar atmosphere

The long-term thermal stability of tritium breeding materials during service is a key factor to ensure efficient tritium release. In this study, the long-term thermal stability of advanced Li₄TiO₄–Li₂TiO₃ core–shell breeding pebbles under continuous heating in 1%H₂/Ar at 900°C was investigated for the first time. The results show that this core–shell material loses 3.4% Li mass after heating for 30 days, resulting in a reduction in Li density to .415 g/cm³, which is still significantly higher than other breeding materials. The moisture in the sample bed will determine the form of Li volatilization and thus affect the rate of Li mass loss. The core–shell pebbles maintain favorable phase stability during long-term heating, and the grain sizes of the Li₂TO₃ shell and Li₄TiO₄ core after 30 days of heating are 6.5 ± 1.5 and 6.9 ± 2.5 μm, respectively. Moreover, the samples did not crack or collapse during long-term heating and still had a satisfactory crushing strength of 37.61 ± 7.13 N after 30 days of heating. Overall, the high Li density and good thermal stability during long-term heating demonstrate that the Li₄TiO₄–Li₂TiO₃ core–shell breeding pebbles are a very reliable tritium breeding material for long-term service under harsh operating conditions.     

Mass fabrication of Li2TiO3–Li4SiO4 ceramic pebbles with high strength by facile centrifugal granulation method

The bi-phase Li₂TiO₃–Li₄SiO₄ ceramic pebbles have been considered a promising breeder to realize the tritium self-sustainment in the blanket. However, up to now, the reported ceramic pebbles have the disadvantages of low yield, poor crushing load, and loose internal structure, which cannot meet the practical application requirements. In this work, the Li₂TiO₃–Li₄SiO₄ ceramic pebbles with excellent mechanical properties were fabricated successfully via the centrifugal granulation method with the assistance of introducing a spray-drying process, simulating particle trajectory by discrete element software and improving bonding interface between core and shell with ethylene glycol. The composition, microstructure, and inner structure of the Li₂TiO₃–Li₄SiO₄ ceramic pebbles were investigated, respectively, through X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and X-ray computed tomography (CT). It can be found that the employment of the ethylene glycol solution on the surface of Li₂TiO₃ can make the core and the shell combine well. Moreover, the effect of the rolling speed of the Li₂TiO₃–Li₄SiO₄ ceramic pebbles was investigated via discrete element method (EDEM) simulation and experiments. The experimental results displayed that the Li₂TiO₃–Li₄SiO₄ ceramic pebbles sintered at 1100°C for 2 h have a uniform diameter of 1 mm, a good sphericity of 0.97, and an excellent crushing load of 82.4 N, which are superior to those pebbles that obtained by using the traditional wet methods. Moreover, the CT results showed that the appropriate porosity of the core was 3.21% and of the shell was 10.73%. Therefore, the simple centrifugal granulation method can be applied to prepare the Li₂TiO₃–Li₄SiO₄ ceramic pebbles in a large scale and shed a light to investigate the relevant advanced biphasic tritium breeder materials in the future.     

A novel process for fully automatic mass-production of Li2TiO3 ceramic pebbles with uniform structure and size

As an excellent promising tritium breeding material, Li₂TiO₃ ceramic pebbles will be required in large quantities in the future. For this reason, a fully automatic pneumatic eject device based on an improved wet process was employed in the mass-preparation of Li₂TiO₃ ceramic pebbles. The operating principle of the equipment, the preparation process parameters and the performance of the Li₂TiO₃ ceramic pebbles have been studied. The results showed that the spheroidization and solidification process of slurries droplets in the molding medium were critical to the sphericity of pebbles, and the size of the green pebbles was related to the droplet dropping speed、the control pressure and the nozzle inner diameter. It is revealed that more than 90% of the pebbles had an eccentricity of less than 1.1, and the diameter distribution was concentrated between 0.98 mm and 1.03 mm. The Li₂TiO₃ ceramic pebbles with the average grain size of 3.7 μm, the crushing load of 67 N, the relative density of 85.6%, and the porosity of 19.96% can be obtained after sintered at 1100 °C for 2 h. Also, the average pore size was 1.3 μm and the distribution was relatively concentrated. Therefore, this method is expected to meet the future demands of Li₂TiO₃ ceramic pebbles with excellent performance in bulk quantity.     

Efficient fabrication of high strength Li2TiO3 ceramic pebbles via improved rolling ball method assisted by sesbania gum binder

In this work, a method combining the spray-drying process and rolling ball method was first selected to mass fabricate Li₂TiO₃ tritium breeder ceramic pebbles. Herein, we overcome the issues namely complex production, high manufacturing cost, and lower mechanical strength in previous reports. The Li₂TiO₃ powder with high packing density after the spray drying process will self-agglomerate to form denser structured pebbles during the rolling ball process assisted by sesbania gum binder solution. The stability of slurry, different binder, binder concentrations, the formation mechanism, and the morphology of green pebbles were investigated by using viscometer, SEM. Moreover, the force on the Li₂TiO₃ green pebbles was also analyzed during the rolling ball process. After the debinding and densification process, the Li₂TiO₃ pebbles have a uniform diameter of 1.2 mm and good sphericity of 0.97. The Micro-CT instrument showed that the internal structure of the Li₂TiO₃ pebbles was dense. The experiment's confirmation shows that the Li₂TiO₃ ceramic pebbles sintered at 1000 °C have optimal mechanical properties such as a crushing load of 108 N and relative density of 92.4%TD, which is much larger than that of the pebbles obtained using traditional methods. This work not only overcomes the core-shell structure but also provides a new platform for better mechanical properties for studying the other materials systems in the future.     

Tritium and deuterium release behavior of Li2TiO3-0.5Li4SiO4–Pb ceramic

The neutron multiplier lead (Pb) containing Li₂TiO₃-0.5Li₄SiO₄–Pb was prepared, which aimed at the improvement of the tritium release performance of the lithium ceramic without an increase in lithium density. Li₂TiO₃-0.5Li₄SiO₄–Pb and that without Pb were irradiated at Kyoto University Research Reactor (KUR) with the thermal neutron flux of 5.5 × 10¹² n s⁻¹ cm⁻² and the fast neutron flux of 1.2 × 10¹² n s⁻¹ cm⁻². Fast neutrons can trigger the Pb (n, 2n) reaction. The tritium release experiments were conducted using the tritium thermal desorption spectroscopy (tritium-TDS) system. Compared with Li₂TiO₃-0.5Li₄SiO₄, the tritium release rate at the lower temperature range was higher than that for Li₂TiO₃-0.5Li₄SiO₄–Pb. The tritium-TDS spectrum was also shifted to the lower temperature side. The isothermal heating experimental results confirmed that tritium in the form of gas species (HT) was controlled by the diffusion process, while the trapping and de-trapping process contributed to the total tritium release. Further, 3 keV D₂⁺ implantation with the fluence of 2.0 × 10²² D m⁻² and subsequent TDS measurements were performed. It was shown that the D₂ release at the lower temperature side was increased for Li₂TiO₃-0.5Li₄SiO₄–Pb. Meanwhile, HD and HDO release at higher temperature side was significantly decreased.     

Preparation of Li2TiO3 ceramic with nano-sized pores by ultrasonic-assisted solution combustion

Li₂TiO₃ is a candidate material for tritium breeding in the future nuclear fusion reactor. In this study, Li₂TiO₃ powder was synthesized by ultrasonic-assisted solution combustion synthesis (USCS) in a single step. The ultrasonic transducer with the power of 1000 W was introduced in the synthesis process. The crystallite size of Li₂TiO₃ powder prepared by utilization of ultrasonic power is significantly decreased to ∼5.0 nm, while the one obtained without ultrasonic power is 20.0 nm. Li₂TiO₃ ceramic sintered from USCS powder at 800 °C exhibits the small grain size of 330 nm and the open pores size of 140 nm. The crush load of the ceramic reaches 37.2 N although the structure is porous. Compared with the ceramic prepared by solid-state reaction and conventional solution combustion synthesis, USCS sample has a higher conductivity of 2.0 × 10⁻⁶ S m⁻¹ at room temperature, indicating the lower tritium diffusion barrier in the ceramic.     

Fabrication of nanostructured Li2TiO3 ceramic pebbles as tritium breeders using powder particles synthesised via a CTAB-assisted method

Nanostructured Li₂TiO₃ ceramics which may have effective thermal conductivity, excellent tritium release behaviour and good irradiation resistance are regarded as a promising solid tritium breeding material for the fusion reactor blanket of the International Thermonuclear Experimental Reactor (ITER). However, due to the limitations of the preparation technology, reports concerning Li₂TiO₃ nanoceramics have been rare. In this paper, uniform nano-Li₂TiO₃ powder particles which were essential to obtain nanostructured Li₂TiO₃ ceramics pebbles were synthesised via a cetyltrimethylammonium bromide (CTAB)-assisted hydrothermal method, and then rare, homogeneous nanostructured Li₂TiO₃ ceramic pebbles were fabricated with the as-prepared powder particles. The mechanisms by which CTAB can reduce particle agglomeration and be of assistance in achieving a nanostructured Li₂TiO₃ ceramic were also investigated. In addition, systematic experiments on the relationship between the added amount of CTAB and the mechanical properties of the Li₂TiO₃ ceramic structure were also carried out. The results revealed that the desired Li₂TiO₃ nanoceramic could be fabricated when 3% CTAB was introduced, as the Li₂TiO₃ pebbles obtained had a small grain size (90 nm), high relative density (89.71%T.D.) and crush load (99.93 N), which were expected to show favourable potential as a promising tritium breeder material in the fusion reactor blanket.     

Comparison of the microwave and conventional sintering of Li2TiO3 ceramic pebbles

Microwave sintering was employed in the fabrication of Li₂TiO₃ ceramic pebbles using the powders synthesized via hydrothermal method. The as-prepared Li₂TiO₃ powders exhibited high reactivity with an average particle size as small as 40?nm. A comparative study between the microwave and conventional sintering behavior of Li₂TiO₃ pebbles was systematically investigated. The microstructure and density analyses showed that the presence of microwaves accelerated the densification and grain growth, thus decreasing the sintering temperature. Besides, an accelerated phase transformation from α-Li₂TiO₃ to β-Li₂TiO₃ was observed in microwave processing. The Li₂TiO₃ ceramic pebbles obtained by microwave sintering exhibited high density, good mechanical property and uniform microstructure, which might hold good potential as tritium breeding materials for blankets. The results showed that the microwave sintering was a promising process for the fabrication of Li₂TiO₃ pebbles.     

Characterization of tritium breeding ceramic pebbles prepared by melt spraying

Li₄SiO₄ and Li₂TiO₃ have long been recognized as two excellent promising tritium breeding materials. In this paper, two kinds of ceramic pebbles, Li₄SiO₄ pure phase ceramic pebbles and Li₄SiO₄-xLi₂TiO₃ multiphase ceramic pebbles were prepared by a melt spraying method at a superheating temperature of 100 ℃ and then tested for their performance. The proportion of pebbles with a particle diameter of 0.8∼1.2 mm reached the maximum of 24.02 % when the spraying pressure is 0.04 MPa. The surface of the pebbles prepared by the spraying method was smooth, and the surface roughness was reported for the first time to reach 2.039 μm. The sphericity reached 1.027. When the Ti/Si molar ratio was 0.5, the crush load of the pebbles after heat treatment reached 71.6 N and the thermal conductivity of the materials reached its maximum of 3.098 W/(m·K) at 700 ℃.     

Preparation and characterization of Li2TiO3 ceramic pebbles by modification of the water-based sol–gel method

Li₂TiO₃ is considered as one of the best candidates for breeding materials. This article adopted a modification water-based sol–gel method to synthesize nano-Li₂TiO₃ powders, which overcomes the poor phase purity, coarse grain, and inferior crushing strength described in the previous literature. In this paper, the thermal effect of the precursor, the crystal phase, and the morphology of the powders were characterized by thermogravimetric analysis/differential thermal analysis (TG/DTA), X-ray diffraction (XRD), and transmission electron microscopy (TEM) techniques. The nano-structured Li₂TiO₃ powders with good dispersion and an average particle size of 20–50 nm were successfully synthesized at 600°C by controlling PH and hydrolysis rate. Moreover, the phase transition temperature for the monoclinic phase β-Li₂TiO₃ was as low as 600°C, which is lower than 750°C using the traditional solid-state method. Meanwhile, the morphology, porosity, crushing load, and thermal conductivity of ceramic pebbles are characterized systematically by using scanning electron microscope (SEM), mercury injection meter, compression strength equipment, and laser scattering method, respectively. Experimental results showed that the Li₂TiO₃ ceramic pebbles with a sphericity of .98, crush load of 48.4 N, and relative density of 90.03 % were successfully prepared at 1050°C for 2 h. This method will provide new guidance for the preparation of tritium breeders.     

An innovative process for synthesis of superfine nanostructured Li2TiO3 tritium breeder ceramic pebbles via TBOT hydrolysis – solvothermal method

In this paper, a method combining hydrolysis of tetrabutyl orthotitanate (TBOT) and solvothermal reaction was first used to fabricate nanostructured Li₂TiO₃ tritium breeder ceramic pebbles. Initially, superfine nanostructured Li₂TiO₃ powders were synthesized with average particle size of about 10?nm, according to TEM. The surface area of precursor particles synthesized via this method was found to be 115.85?m²/g by BET analysis, which is much larger than that of the product obtained using traditional methods. The results showed that precursor particles had high sintering activity. XRD pattern revealed that the phase transition temperature for monoclinic phase Li₂TiO₃ prepared by this method was nearly 450?°C, which was the lowest phase transition temperature reported among all wet chemical methods to date. Subsequently, investigation of ceramic sintering demonstrated that Li₂TiO₃ ceramic pebbles with desired nano-crystalline sizes (27.98 ~ 55.03?nm) were obtained by sintering at 500 ~ 600?°C for 4?h. The possible mechanisms were proposed based on the reaction processes of TBOT hydrolysis, solvothermal reaction and sintering.     

Fabrication of attractive Li4SiO4 pebbles with modified powders synthesized via surfactant-assisted hydrothermal method

Li₄SiO₄ pebbles have been widely studied as attractive tritium breeding materials in the fusion reactor blanket of international thermonuclear experimental reactor (ITER). In this work, surfactant-assisted hydrothermal method was first employed to prepare ultrafine ceramic powders for fabricating attractive Li₄SiO₄ pebbles. SEM analysis revealed that the introduction of sodium dodecyl sulfate could eliminate the particle aggregation to prepare monodispersed precursor powders, and thus generated the green bodies of pebble with homogeneous microstructure, which was helpful to eventually obtain high-quality Li₄SiO₄ pebbles. Moreover, the effects of sintering temperature on the grain size, relative density, and crush load of Li₄SiO₄ pebbles were also investigated. Li₄SiO₄ pebbles sintered at 700 °C had a high crush load (average value 27.39 N), small grain size (average value 0.57 μm), satisfactory density (88.13%T.D.) and abundant pore structure, which were expected to show favorable tritium release behavior as a promising tritium breeding material for fusion reactor blanket.     

Stable composite electrolytes of PVDF modified by inorganic particles for solid-state lithium batteries

Polymer electrolytes have been attracting much attention because of their flexibility and easy follow-up processing, but their Li⁺ conductivity in lithium-metal batteries (LIBs) is unsatisfactory. Stable composite electrolytes of poly (vinylidene fluoride) (PVDF) polymer with high lithium-ion conductivity have been prepared by a trigger structural modification of Li_6.5La₃Zr_1.5Nb_0.25Ta_0.25O₁₂ (LLZNTO) garnet ceramic and TiO₂ oxide. The influences of various amounts of TiO₂ and LLZNTO on electrochemical performance were systematically examined. These composite electrolytes exhibited maximal Li⁺ conductivity of 2.89 × 10⁻⁴ S cm⁻¹, which is consistent with the value of pure ceramic electrolytes. Furthermore, it possessed the stable long-term Li cycling and the wide electrochemical window, involving repeated Li plating/stripping at 0.2 mA cm⁻² over 280 h without failure. The discharge specific capacity and Coulomb efficiency for all-solid-state LIBs assembled with these membranes delivered outstanding cycling stability with high discharge capacities (117.9 mA h g⁻¹) at 0.1 C rate and Coulomb efficiency reached 99.9% after 25 cycles. The high Li⁺ conduction capability can be ascribed function of introducing TiO₂ and LLZNTO to restrain tremendously the crystalline behavior of the polymer. Furthermore, the LLZNTO can be complex with PVDF for dehydrofluorination, and it can also offer a burst transportation route for lithium ions. This system might serve as an attractive use for polymer solid electrolytes and open up new possibilities for safe all-solid-state LIBs.     

One-step fabrication of Li2TiO3 ceramic pebbles using pulsed YAG laser

A large amount of Li-containing ceramic breeder pebbles is packed in the solid breeding blanket of a nuclear fusion reactor. Several pebble fabrication technologies have been proposed in previous studies, including wet process, emulsion method, extrusion spheronization, additive manufacturing, and melt process. However, a simple, energy-effective, and scalable fabrication technology remains to be developed for the automated mass production and reprocessing of used radioactive pebbles post-operation. Selective laser melting potentially enables the quick and automated fabrication of breeder pebbles. Herein, we employ a high-power density pulse laser to produce ceramic breeder pebbles. A pulsed YAG laser was irradiated over a lithium metatitanate (Li₂TiO₃) powder bed in air, and the corresponding temperature was monitored using fiber-type infrared pyrometers. Spherical Li₂TiO₃ pebbles were successfully fabricated in a single step with an average diameter of 0.78 ± 0.13 μm and the sintering density of 87.4% ± 5.6% (input power: 7.9 J/pulse). The irradiated Li₂TiO₃ powder melted and turned spherical under surface tension and rapidly solidified, resulting in uniaxial fine grains and a decrease in the degree of long-range cation ordering.     

Preparation of tritium breeding Li2TiO3 ceramic pebbles via newly developed piezoelectric micro-droplet jetting

Wet methods as an emerging technique for the preparation of millimeter-sized tritium breeding ceramic pebbles, but the imposed air pressure as the driving forces to extrude slurry droplets are fluctuating during the reciprocating extrusion process, which caused a slight inconsistency in pebble sizes. In this study, a piezoelectric micro-droplet jetting approach was proposed by introducing a piezo-driven valve and modifying the slurry barrel mechanism to realize the air pressure invariable. A self-developed piezoelectric micro-droplet jetting device was successfully utilized to prepare Li₂TiO₃ green pebbles with coefficients of variation being lower than 2.7%. The size of the green pebbles could be precisely controlled in the range of 0.88–1.37 mm by manipulating the nozzle diameter, the air pressure, and the jetting time. The pebbles sintered at 1000°C for 3 h possessed a small grain size of ∼5.9 μm, a satisfied relative density of ∼84.8% T.D., and a high crush load of ∼25.7 N, implying the prepared pebbles could be used as a promising solid tritium breeding material in fusion reactors. These findings are anticipated to provide new opportunities for the highly efficient preparation of size-controllable tritium breeding ceramic pebbles.     

A novel mass production method for Li2TiO3 tritium breeder ceramic pebbles using polyvinyl alcohol (PVA) and polyvinyl pyrrolidone (PVP) assisted granulation method

A novel mass production method of lithium titanite (Li₂TiO₃) tritium breeder ceramic pebbles using polyvinyl alcohol (PVA) and polyvinyl pyrrolidone (PVP) assisted granulation method (APG) was proposed. A binder solution of polyvinyl alcohol (PVA) was used to modify the Li₂TiO₃ precursor powder. The powders with adhesive properties were prilled to form green pebbles (GPs) by spheronization at a low rotation speed and spraying with polyvinyl pyrrolidone (PVP), in several cycles. Then, the density and the crush load of the GPs were improved by high-speed rolling. Finally, the ceramic pebbles were produced by sintering. The phase, the microstructure, and the crush load of the ceramic pebbles were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and with a universal tester, respectively.     

Influence of helium ion radiation on the nano-grained Li2TiO3 ceramic for tritium breeding

Lithium titanium oxide (Li₂TiO₃) tritium breeder ceramic plates with nano- and coarse-grain size were fabricated. The preparation methods contained CTAB-modifying precursor, combining dry-pressing with isostatically cold-pressing, and calcinating at optimized sintering temperature in turn. Then their properties were characterized after radiation by 280 keV helium (He⁺) ion. Extensive characterization analyses were performed to reveal the changes in nano-grained and coarse-grained Li₂TiO₃ after radiation. They contained glancing angle X-ray diffraction (GIXRD), atomic force microscopy (AFM), electron spin resonance (ESR), and scanning electron microscopy (SEM). The results showed as follows, GIXRD peak position of the nano-grained Li₂TiO₃ was more stable than the coarse-grained Li₂TiO₃ after radiation. Nano-grained Li₂TiO₃ was less rough and swollen than the coarse-grained one after radiation. Nano-grained Li₂TiO₃ had more excellent structural stability and less defect concentration of Eʹ-center after radiation. As a result, nano-grained Li₂TiO₃ might have much better radiation tolerance than the coarse-grained one by comparing characterization results.     

A comparative study on the properties of Li2TiO3 powders and pebbles fabricated by different routes

Lithium titanate (Li₂TiO₃) is one of the promising candidate breeders for tritium self-sufficiency of deuterium(D)-tritium(T) fusion reaction. The differences in powder synthesis methods have a great impact on the properties of Li₂TiO₃ powders and the performance of Li₂TiO₃ ceramic pebbles. In this study, the Li₂TiO₃ powders were successfully synthesized by hydrothermal method and solid-state method, and then the pebbles were fabricated by the agar-based wet method. The mechanism of hydrothermal synthesis of Li₂TiO₃ powder was discussed. For the hydrothermal method, the Li₂TiO₃ powder with single phase can be obtained when the rate of Li/Ti = 2.4, and the powder presented two different morphology, which involved two reaction mechanisms, including in-situ phase transformation mechanism and dissolution-precipitation mechanism, the phase transformation from α-Li₂TiO₃ to β-Li₂TiO₃ accomplished at 400°C, which is lower than that of 750°C for solid-state method. Li₂TiO₃ pebbles prepared by the hydrothermal-wet method had a uniform pore distribution, an optimal grain size of 2.7 μm, a crushing load of 58.6 N, and relative density of 90.2%, respectively. In comparison, pebbles prepared by the solid-state-wet method also had better mechanical properties, which the crushing load and relative density were 53.9 N and 86.9% respectively under the optimal fabrication conditions.     

Low-cost fabrication of Li2TiO3 tritium breeding ceramic pebbles via low-temperature solid-state precursor method

Lithium metatitanate (Li₂TiO₃) ceramic pebbles were fabricated from the powder synthesised via low-temperature solid-state precursor method. Solid H₂TiO₃ and LiOH·H₂O react chemically during ball milling process to form a nano-sized precursor powder. Pure β-Li₂TiO₃ powder can be obtained by calcining the precursor powder at 500 °C, which is half the temperature of conventional solid-state method. The synthesis process is simple and low-cost, which would be more available to achieve batch production among all feasible techniques. The low-temperature calcination will effectively avoid hard particle aggregates and poor sinterability caused by high-temperature heat treatment, which is conducive to prepare ceramics with good properties. The results show that the powder exhibits high sinterability with small particle size of 19 nm. The Li₂TiO₃ ceramic pebbles sintered at 800 °C have small grain size (470 nm), high relative density (83%) and good crush load (45 N), which has great potential as tritium breeding materials for fusion reactors.     

Influence of sintering atmosphere on phase,microstructure and mechanical properties of Li4Si0.7Ti0.3O4 tritium breeding ceramics

Li₄Si_1–xTi_xO₄ ceramic solid solution was considered as a promising tritium breeding material for fusion reactor blanket. In this work, the effects of the sintering atmosphere on the phase composition, microstructure, and mechanical properties of Li₄Si_0.7Ti_0.3O₄ ceramic pebbles were investigated for the first time, aiming to explore the optimal sintering atmosphere for this solid solution. The results show that compared with air and argon atmosphere, the negative pressure of vacuum atmosphere was more favorable for Ti to enter the Li₄SiO₄ crystal structure as a substitute for Si atom to form a solid solution. More importantly, sintering in argon-vacuum atmosphere can ensure the formation of solid solution while fully exerting the liquid phase sintering effect. The crushing load of the Li₄Si_0.7Ti_0.3O₄ ceramic pebbles sintered at 800 °C in argon-vacuum atmosphere reaches 30.3 ± 3.2 N. In general, the appropriate sintering atmosphere was of great significance for obtaining Li₄Si_0.7Ti_0.3O₄ solid solution to meet the performance requirements of tritium breeding blanket.