Mass transfer correlation of NH3–H2O bubble absorption

The objectives of this paper are to study the effect of key parameters on absorption performance and to develop an experimental correlation of mass transfer coefficient for ammonia–water bubble absorption. The orifice diameter, liquid concentration and vapor velocity are considered as the key parameters. This study successfully visualized the bubble behavior and measured the volumetric diameter of bubbles during the bubble absorption process. The bubble absorption is grouped into two processes, bubble growth (process I) and bubble disappearance (process II), respectively. The following conclusions were drawn from the present study. A new experimental correlation for the volumetric bubble diameter was proposed with ±15% error band, which could be applied to calculate the mass transfer coefficient. The mass transfer coefficient increased with a decrease of the liquid concentration. In process II, the mass transfer coefficient increased with an increase of the Galileo number. Finally, experimental correlations of mass transfer coefficient were developed for processes I and II with ±18% error bands.     

Analytical investigation of two different absorption modes: falling film and bubble types

The objectives of this paper are to analyze a combined heat and mass transfer for an ammonia–water absorption process, and to carry out the parametric analysis to evaluate the effects of important variables such as heat and mass transfer areas on the absorption rate for two different absorption modes — falling film and bubble modes. A plate heat exchanger with an offset strip fin (OSF) in the coolant side was used to design the falling film and the bubble absorber. It was found that the local absorption rate of the bubble mode was always higher than that of the falling film model leading to about 48.7% smaller size of the heat exchanger than the falling film mode. For the falling film absorption mode, mass transfer resistance was dominant in the liquid flow while both heat and mass transfer resistances were considerable in the vapor flow. For the bubble absorption mode, mass transfer resistance was dominant in the liquid flow while heat transfer resistance was dominant in the vapor region. Heat transfer coefficients had a more significant effect on the heat exchanger size (absorption rate) in the falling film mode than in the bubble mode, while mass transfer coefficients had a more significant effect in the bubble mode than in the falling film mode.     

Experimental correlation of combined heat and mass transfer for NH3–H2O falling film absorptionCorrélation expérimentale entre le transfert de chaleur et de masse pour de l'absorption au NH3–H2O à film tombant

In this article, experimental analysis was performed for ammonia–water falling film absorption process in a plate heat exchanger with enhanced surfaces such as offset strip fin. This article examined the effects of liquid and vapor flow characteristics, inlet subcooling of the liquid flow and inlet concentration difference on heat and mass transfer performance. The inlet liquid concentration was selected as 5%, 10% and 15% of ammonia by mass while the inlet vapor concentration was varied from 64.7% to 79.7%. It was found that before absorption started, there was a rectification process at the top of the test section by the inlet subcooling effect. Water desorption phenomenon was found near the bottom of the test section. It was found that the lower inlet liquid temperature and the higher inlet vapor temperature, the higher Nusselt and Sherwood numbers are obtained. Nusselt and Sherwood number correlations were developed as functions of falling film Reynolds Re₁, vapor Reynolds number Re_v, inlet subcooling and inlet concentration difference with ±15% and ±20% error bands, respectively.     

Development of a slug flow absorber working with ammonia-water mixture: part I—flow characterization and experimental investigation

This study deals with an experimental investigation for a counter-current slug flow absorber, working with ammonia–water mixture, for significantly low solution flow rate conditions that are required for operating as the GAX (generator absorber heat exchanger) cycle. It is confirmed that the slug flow absorber operates well at the low solution flow rate conditions. From visualization results of the flow pattern, frost flow just after the gas inlet, followed by slug flow with well-shaped Taylor bubble, is observed, while dry patch on the tube wall are not observed. The liquid film at the slug flow region has smooth gas–liquid interface structure without apparent wavy motion. The local heat transfer rate is measured by varying main parameters, namely, ammonia gas flow rate, solution flow rate, ammonia concentration of inlet solution and coolant inlet conditions. The heat transfer rate while absorption is taking place is higher than that after absorption has ended. The absorption length is greatly influenced by varying main parameters, due to flow conditions and thermal conditions.     

A phenomenological theory of polycomponent interactions in non-ideal mixtures. Application to NH3/H2O and other working pairsInteractions entre les composants de mélanges non-idéaux : théorie et application au fluide actif NH3 / H2O et à d'autres fluides actifs

The paper proposes an original linear phenomenological theory (Ph T) of evolution physical mono-, bi- and particular polycomponent gas–liquid interactions with non-ideal mixture. The expressions of the phenomenological factors (entropy source, force, coefficient and coupled heat and mass transfer currents) are deduced. The theory is particularized to the NH₃/H₂O and other gas–liquid systems used in the thermal absorption technology. The work's conclusions are listed next. The paper raises the problem of ammonia bubble absorption which is difficult to answer with current theory of interface mass transfer and absorption as a surface phenomenon. The heat and mass transfer at the gas–liquid interface is governed by the thermodynamic force, which applies also to solid–liquid, solid–gas, or liquid–liquid, gas–gas type interactions and continuous or discontinuous media. The paper mentions a postulate referring to the force behavior approaching an ideal point, previously formulated by the author. According to its consequence, the mass and heat currents suffer an ideal point approaching (i.p.a.) effect, not mentioned so far in the specialized literature, consisting in a continuous increase of their absolute value by several percent (for a pure component), to several hundred times (for a binary system) when the interacting system approaches an ideal state, as compared to the values of states which are far from the same ideal point. In this way, “far from equilibrium” becomes synonymous to “low interaction”. The classic assessment of the interface mass transfer by analogy with heat transfer lacks basic physics. The (Ph T) satisfactorily explains the problem of ammonia bubble absorption. Absorption is a mass phenomenon, not a surface one. An intensive way of improving absorption is emphasized, which seeks to promote the i.p.a. effect appearance rather than the extensive way currently used, based on increasing gas–liquid interaction area. To this extent, the bubble absorber is hereby proposed for efficient absorption. The i.p.a. effect existence offers an additional chance for a satisfactory explanation of the Marangoni effect.     

Distillation column configurations in ammonia–water absorption refrigeration systems

In ammonia–water absorption refrigeration systems a purification process to reduce the water content in the vapour leaving the generator is required. During this process the water content in the vapour must be reduced to a minimum, otherwise it tends to accumulate in the evaporator and strongly deteriorates the efficiency of the system. The vapour purification can be carried out by partial condensation, by establishing a liquid–vapour counter flow or by combining both methods. In systems with partial condensation, the distillation column can be composed of one or more rectifiers using different cooling mediums, and the rectifying and stripping sections. In complete condensation systems only the rectifying and stripping sections can be used. Therefore different distillation column arrangements should be considered. This paper presents a study of several distillation column configurations for single stage ammonia–water absorption refrigeration systems with partial and complete condensation. In order to evaluate and compare the different configurations, a parameter that indicates the ratio of the ammonia vapour concentration increase in each part of the column to the total ammonia purification has been defined. The analysis has been based on the system COP. Finally the efficiency in each part of the column has been calculated to estimate its design requirements.     

Studies on bubble pump for a water–lithium bromide vapour absorption refrigerator: Etudes sur une pompe à bulles pour réfrigérateur à absorption eau–bromure de lithium

The hydrostatic principle and bubble pump technique are used in the two-fluid pumpless continuous vapour absorption refrigerator to create the circulations of the solution and refrigerant. In this paper, the bubble pump, which is the ‘heart' of this natural circulation type of refrigerator, has been investigated both analytically and experimentally. The bubble pump is modelled for intermittent slug flow of solution and vapour mixture. A test rig is built in glass to evaluate the performance of the bubble pump, to visualize the flow behavior and to validate the analytical model. Bubble pump tube diameter, pump lift, driving head and heat input are varied to analyze the pump performance. Results indicate that pumping ratio is nearly independent of the heat input, but increases with decrease in pump tube diameter, decrease in pump lift and increase in driving head.     

Simulation study of a hybrid absorber–heat exchanger using hollow fiber membrane module for the ammonia–water absorption cycle

An innovative hybrid hollow fiber membrane absorber and heat exchanger (HFMAE) made of both porous and nonporous fibers is proposed and studied via mathematical simulation. The porous fibers allow both heat and mass transfers between absorption solution phase and vapor phase, while the nonporous fibers allow heat transfer between absorption solution phase and cooling fluid phase only. The application of HFMAE on an ammonia–water absorption heat pump system as a solution-cooled absorber is analyzed and compared to a plate heat exchanger falling film type absorber (PHEFFA). The substantially higher amount of absorption obtained by the HFMAE is made possible by the vast mass transfer interfacial area per unit device volume provided. The most dominant factor affecting the absorption performance of the HFMAE is the absorption solution phase mass transfer coefficient. The application of HFMAE as the solution-cooled absorber and the water-cooled absorber in a typical ammonia–water absorption chiller allows the increase of COP by 14.8% and the reduction of the overall system exergy loss by 26.7%.     

Dynamic simulation of a single-effect ammonia–water absorption chiller

A lumped-parameter dynamic simulation of a single-effect ammonia–water absorption chiller is performed. Modeling is based on the continuity of species constituting the ammonia–water mixture and the conservation of energy for each component of the absorption chiller. Ordinary differential equations governing the response of each component and the algebraic equations describing the constitutive relation are solved in parallel by numerical integration. The model has been applied to a commercially available 10.5 kW absorption chiller to study the transients of temperature, pressure, concentration, and void fraction of each component during the start-up operation. The time constant of the absorption chiller is also investigated. The parameters considered are the bulk concentration of the ammonia–water solution, the mass of the solution filled, and the volumes of key components of the absorption chiller. In addition, the reduction of the time constant by a stepwise turn-up and turn-down of the flue gas flow rate during the primary stage of start-up period is demonstrated.     

Heat transfer enhancement by Marangoni convection in the NH3–H2O absorption process

The objectives of this paper are to quantify the effect of Marangini convection on the absorption performance for the ammonia–water absorption process, and to visualize Marangoni convection that is induced by adding a heat transfer additive, n-octanol. A real-time single-wavelength holographic interferometer is used for the visualization using a He–Ne gas laser. The interface temperature is always the highest due to the absorption heat release near the interface. It was found that the thermal boundary layer (TBL) increased faster than the diffusion boundary layer (DBL), and the DBL thickness increased by adding the heat transfer additive. At 5 s after absorption started, the DBL thickness for 5 mass% NH₃ without and with the heat transfer additive was 3.0 and 4.5 mm, respectively. Marangoni convection was observed near the interface only in the cases with heat transfer additive. The Marangoni convection was very strong just after the absorption started and it weakened as time elapsed. It was concluded that the absorption performance could be improved by increasing the absorption driving potential (x_vb−x_vi) and by increasing the heat transfer additive concentration. The absorption heat transfer was enhanced as high as 3.0–4.6 times by adding the heat transfer additive that generated Marangoni convection.     

A study on numerical simulations and experiments for mass transfer in bubble mode absorber of ammonia and water

An absorber is a major component in the absorption refrigeration systems, and its performance greatly affects the overall system performance. In this study, both the numerical and experimental analyses in the absorption process of a bubble mode absorber were performed. Gas was injected into the bottom of the absorber at a constant solution flow rate. The region of gas absorption was estimated by both numerical and experimental analyses. A higher gas flow rate increases the region of gas absorption. As the temperature and concentration of the input solution decrease, the region of gas absorption decreases. In addition, the absorption performance of the countercurrent flow was superior to that of cocurrent. Mathematical modeling equations were derived from the material balance for the gas and liquid phases based on neglecting the heat and mass transfer of water from liquid to gas phase. A comparison of the model simulation and experimental results shows similar values. This means that this numerical model can be applied for design of a bubble mode absorber.     

An experimental investigation on performance of bubble pump with lunate channel for absorption refrigeration system

An experimental research on the performance of the bubble pump for absorption refrigeration units was made. The bubble pump provides the drive for the absorption cycle and is a decisive component of the absorption refrigeration unit. The bubble pump's property determines the efficiency of the absorption refrigeration system. A continuous experimental system with different size of bubbles pumps were designed, constructed and successfully worked. The experiments were performed by changing some of the parameters affecting the bubble pump performance. The experimental results shows that the performance of the bubble pump depends mainly on the driving temperature, the solution head and the combining tube diameters. With the suitable size of section area of the pump tubes the net elevating height of solution is 2.5 times as high as the solution submergence. The lunate channel has several outstanding characteristics, such as low starting temperature (minimum 68 °C), wide operating temperature range and lower requirement for vacuum condition (under 10 kPa). Then the elevating capability of the bubble pump with lunate channel is much better than others currently. It would provide well foundation for practical applications.     

Simulation of ternary ammonia–water–salt absorption refrigeration cyclesSimulation des cycles frigorifiques à absorption à ammoniac / eau / sel

This paper proposes a new working fluid for refrigeration cycles utilizing low temperature heat sources. The proposed working fluid consists of the ammonia–water working fluid mixture and a salt. The salt is used to aid the removal of ammonia from the liquid solution. This effect is a manifestation of the well known “salting-out” effect. While the addition of salt improves the generator performance, it also has a detrimental effect on the absorber. The overall effects on the performance of three absorption cycles using the NH₃–H₂O–NaOH working fluid have been investigated using computer simulations. The results indicated that salting out can lower the generator operating temperature while simultaneously improving the cycle performance. Furthermore, limiting the salt to the generator suggests potential for further improvement in cycle performance.     

The effect of nano-particles on the bubble absorption performance in a binary nanofluid

The objectives of this paper are to examine the effect of nano particles on the bubble type absorption by experiment and to find the optimal conditions to design highly effective compact absorber for NH₃/H₂O absorption system. The initial concentrations of NH₃/H₂O solution and the kinds and the concentrations of nano particles are considered as key parameters. The results show that the addition of nano particles enhances the absorption performance up to 3.21 times. Moreover, the absorption rate increases with increasing concentration of nano particles and the nano particles are more effective for lower absorption potential solution. The potential enhancement mechanism for binary nanofluid is suggested. The experimental correlations of the effective absorption ratio for each nano particles, Cu, CuO, and Al₂O₃, are suggested within ±10% error-band.     

Mass transfer characteristics of a structured packing for ammonia rectification in ammonia–water absorption refrigeration systems

In ammonia–water absorption refrigeration systems a purification process of the vapours produced in the generator is required. One type of equipment to carry out the purification process is a packed column. However, detailed experimental studies at the normal operating conditions found in ammonia–water absorption refrigeration systems have not been found. An experimental facility has been designed and built to study the ammonia–water rectification in packed columns. Experimental tests have been performed at the normal operating conditions found in the high-pressure stage of a small power ammonia–water absorption refrigeration system. In this paper, the experimental set-up is described and experimental results of the height equivalent to a theoretical plate (HETP) and the volumetric mass transfer coefficient of a rectifying section with the Sulzer BX packing are presented. The HETP values and the experimental mass transfer coefficients are compared with different data and correlations proposed in the literature; it has been found that the differences are appreciable.     

Dynamic behaviour of the CO<Subscript>2</Subscript> bubble in a bubble column bioreactor for microalgal cultivation

Carbon dioxide (CO₂) gas is a major carbon source for microalgal cultivation. It is usually sparged into photobioreactors in the form of bubbles. The behaviour of the bubbles significantly affects mass transfer, distribution and microalgae growth. In this study, the dynamic behaviour of the CO₂ bubbles was compared between a microalgal suspension and pure water. These investigations were carried out via visual methods. The movement and distribution of microalgae at the gas–liquid interface were observed. The effects of gas flow velocity, CO₂ concentration and capillary orifice size were analysed. The results indicated that much of the microalgal cells adsorbed onto the surface of the CO₂ bubbles in the microalgal suspension, when compared with that in pure water. This resulted in an easier detachment of the bubbles in the microalgal suspension. The growth status of the bubbles were divided into two states according to changes in the Eötvös number and the behaviour of the CO₂ bubbles as influenced by gas flow velocity: steady and unsteady state. The critical gas velocity between the two states was achieved. The CO₂ bubble rising trajectory can be divided into three main phases: the vertical acceleration phase, the transition phase, and the oscillatory rising phase. During the oscillatory rising phase, the amplitude of the bubble rising trajectory was approximately two times greater than the bubble diameter. In addition, the wavelength of the bubble rising trajectory was approximately 16–18 times the bubble diameter in the microalgal suspension. A smaller capillary orifice size and larger CO₂ concentration led to a decrease in the bubble detachment diameter, an increase in velocity and an enlargement in the zone of bubble influence in the horizontal direction. These are advantageous for CO₂ transportation. These findings are beneficial for optimizing the design and operation of microalgal photobioreactors.     

Development of a slug flow absorber working with ammonia–water mixture: part II—data reduction model for local heat and mass transfer characterization

This study deals with a data reduction model for clarifying experimental results of a counter-current slug flow absorber, working with ammonia–water mixture, for significantly low solution flow rate conditions. The data reduction model to obtain the local heat and mass transfer coefficient on the liquid side is proposed by using the drift flux model to analyze the flow characteristics. The control volume method and heat and mass transfer analogy are employed to solve the combined heat and mass transfer problem. As a result, it is found that the local heat and mass transfer coefficient on the liquid side of the absorber is greatly influenced by the flow pattern. The heat and mass transfer coefficient at the frost flow region is higher than that at the slug flow region due to flow disturbance and random fluctuation. The solution flow rate and gas flow rate have influence on the local heat and mass transfer coefficient at the frost flow region. However, it is insignificant at the slug flow region.     

Twin screw oil-free wet compressor for compression–absorption cycle

The performance of a twin screw compressor operating under wet (two-phase) compression conditions in an ammonia–water compression absorption heat pump cycle is investigated both theoretically and experimentally. The paper reports on the influence of the location of liquid intake or, depending what applies, injection angle and mass flow rate of the injected liquid on compressor performance. Labyrinth seals separate the oil-free process side from oil lubricated bearing housing. Labyrinth seals leakage is modelled and its impact on performance is theoretically and experimentally investigated. The need for liquid injection from the discharge side to obtain acceptable performance is discussed based on experimental results.     

The effect of chemical surfactants on the absorption performance during NH3/H2O bubble absorption process

The objectives of this paper are to visualize the bubble behavior by shadow graphic method, to examine the effect of surfactants on the bubble type absorption, and to find the optimal conditions to design highly effective compact absorber for NH₃/H₂O absorption system. The initial concentrations of NH₃/H₂O solution and the kinds and the concentrations of surfactants are considered as key parameters. By measuring the absorption rate for each condition, two effects of the addition of surfactants, the Marangoni and the barrier effect, are compared with each other. The results show that the addition of surfactant enhances the absorption performance up to 4.81 times. The experimental correlations of the effective absorption ratio for each surfactant, 2-ethyl-1-hexanol, n-octanol, and 2-octanol, are suggested within ±15, ±10, and ±10%, respectively.     

Heat and mass transfer enhancement of binary nanofluids for H2O/LiBr falling film absorption process

The objectives of this study are to measure the vapor absorption rate and heat transfer rate for falling film flow of binary nanofluids, and to compare the enhancement of heat transfer and mass transfer under the same conditions of nanofluids. The key parameters are the base fluid concentration of LiBr, the concentration of nanoparticles in weight %, and nanoparticle constituents. The binary nanofluids are H₂O/LiBr solution with nanoparticles of Fe and Carbon nanotubes (CNT) with the concentrations of 0.0, 0.01 and 0.1 wt %. The vapor absorption rate increases with increasing the solution mass flow rate and the concentration of Fe and CNT nanoparticles. It is found that the mass transfer enhancement is much more significant than the heat transfer enhancement in the binary nanofluids with Fe and CNT. It is also found that the mass transfer enhancement from the CNT nanoparticles becomes higher than that from the Fe nanoparticles. Therefore, the CNT is a better candidate than Fe nanoparticles for absorption performance enhancement in H₂O/LiBr absorption system.