Method of gasification in IGCC system

A coal gasifier is designed to operate at the temperature range of 1200–1300 °C. The 1200 °C sets the lower limit to the carbon reforming efficiency of the high temperature reformer, and the 1300 °C is the lower limit of the fluid temperature of coal slags, below which they may be collected as non-fluid slag. The gasifier is connected to two syngas burners where a portion of product syngas is combusted with O₂ gas and produce ultra hot H₂O and CO₂ gases, these two gases enter into the gasifier and maintain the gasifier temperature at above 1200 °C and reform carbon into syngas. The temperature of the gasifier is controlled by the flow of O₂ gas into the syngas burner, where O₂ gas is completely consumed and none left to enter into the gasifier. This removes any possibility of forming oxidated products, and compressed CO₂ gas spray coal powder into the gasifier column and non-fluid slag is collected at the bottom. A higher level integration of oxidation–reduction cycle is shown for a IGCC system, wherein the exhaust gas of syngas turbine drives the reduction reaction of coal gasification.

A smooth and uniform temperature control within the gasifier assures high efficiency of carbon reforming and quality of product syngas. Conventional Lurgi gasifier relies on its large heat capacity and accumulating coal slag along the inner walls of the gasifier has made the gasifier bigger, lately as large as a three story building. The gasifier of the present design is constructed much smaller in its size, but with greater reforming efficiency.     

Exergy analysis of updraft and downdraft fixed bed gasification of village-level solid waste

The most commonly used for gasification of village-level solid waste is the fixed-bed gasifier, but there is no reasonable method to evaluate the gasification process. This paper attempts to find a gasifier that is most suitable for gasification of village-level solid wastes through exergy analysis method. Based on experimental data from literature, the exergy efficiencies and LHV(Low Heat Value) of product gas from updraft and downdraft fixed bed gasifier are studied in this paper. The results show that the updraft fixed bed gasifier has higher exergy efficiency, and the gas produced by the downdraft fixed bed gasifier has a higher heating value. Air gasification has higher exergy efficiency than steam gasification and pure oxygen gasification. The highest exergy efficiency at a gasification temperature of about 1000 °C and ER (Equivalence Ratio) value in the range of 0.33–0.36. The volatile content of gasification raw materials is higher, and the gasification efficiency is higher. Through the research of this paper, a new path to reasonably evaluate the gasification process is obtained.     

Thermal pretreatment of wood (Lauan) block by torrefaction and its influence on the properties of the biomass

The purpose of this study is to investigate the torrefaction behavior of woody biomass (Lauan) blocks and its influence on the properties of the wood. Three different torrefaction temperatures of 220, 250 and 280 °C, corresponding to light, mild and severe torrefactions, and four torrefaction times of 0.5, 1, 1.5 and 2 h were considered. After analyzing the torrefied woods, it was found that the torrefaction temperature of 280 °C was able to increase the calorific value of the wood up to 40%. However, over 50% of weight was lost from the wood. The grindability of the torrefied wood could be improved in a significant way if the torrefaction temperature was as high as 250 °C and the torrefaction time longer than 1 h. Therefore, the torrefaction temperature of 250 °C along with the torrefaction time longer than 1 h was the recommended operation to intensify the heating value and grindability as well as to avoid too much mass loss of the wood. This study also suggested that over 50% of the reacted wood was converted into condensed liquid. The main components in the liquid were monoaromatics; little amount of heterocyclic hydrocarbons were also obtained from the torrefactions, especially at the torrefaction temperature of 280 °C.     

Effect of fuel blend composition on hydrogen yield in co-gasification of coal and non-woody biomass

In this study, torrefaction of sunflower seed cake and hydrogen production from torrefied sunflower seed cake via steam gasification were investigated. Torrefaction experiments were performed at 250, 300 and 350 °C for different times (10–30 min). Torrefaction at 300 °C for 30 min was selected to be optimum condition, considering the mass yield and energy densification ratio. Steam gasification of lignite, raw- and torrefied biomass, and their blends at different ratios were conducted at downdraft fixed bed reactor. For comparison, gasification experiments with pyrochar obtained at 500 °C were also performed. The maximum hydrogen yield of 100 mol/kg fuel was obtained steam gasification of pyrochar. The hydrogen yields of 84 and 75 mol/kg fuel were obtained from lignite and torrefied biomass, respectively. Remarkable synergic effect exhibited in co-gasification of lignite with raw biomass or torrefied biomass at a blending ratio of 1:1. In co-gasification, the highest hydrogen yield of 110 mol/kg fuel was obtained from torrefied biomass-lignite (1:1) blend, while a hydrogen yield from pyrochar-lignite (1:1) blend was 98 mol/kg. The overall results showed that in co-gasification of lignite with biomass, the yields of hydrogen depend on the volatiles content of raw biomass/torrefied biomass, besides alkaline earth metals (AAEMs) content.     

Exergy analysis of synthetic natural gas production method from biomass

The paper presents the results of exergy analysis for a biomass-to-synthetic natural gas (SNG) conversion process. The presented study is based on wood gasification, which is analysed for different gasification conditions like temperature and/or pressure. The analysed temperature was varied in the range from 650 to 800 °C and the pressure range was from 1 to 15 bar. The main process units of biomass-to-SNG conversion technology are gasifier, gas cleaning, synthesis gas compression, CH₄ synthesis and final SNG conditioning. The results showed that the largest exergy losses take place in the biomass gasifier, CH₄ synthesis part and CO₂ capture unit. The overall exergetic efficiency of the biomass-to-SNG process was estimated in the range of about 69.5–71.8%.     

Exergetic evaluation of biomass gasification

Biomass has great potential as a clean, renewable feedstock for producing modern energy carriers. This paper focuses on the process of biomass gasification, where the synthesis gas may subsequently be used for the production of electricity, fuels and chemicals. The gasifier is one of the least-efficient unit operations in the whole biomass-to-energy technology chain and an analysis of the efficiency of the gasifier alone can substantially contribute to the efficiency improvement of this chain. The purpose of this paper is to compare different types of biofuels for their gasification efficiency and benchmark this against gasification of coal. In order to quantify the real value of the gasification process exergy-based efficiencies, defined as the ratio of chemical and physical exergy of the synthesis gas to chemical exergy of a biofuel, are proposed in this paper. Biofuels considered include various types of wood, vegetable oil, sludge, and manure. In this study, exergetic efficiencies are evaluated for an idealized gasifier in which chemical equilibrium is reached, ashes are not considered and heat losses are neglected. The gasification efficiencies are evaluated at the carbon-boundary point, where exactly enough air is added to avoid carbon formation and achieve complete gasification. The cold-gas efficiency of biofuels was found to be comparable to that of coal. It is shown that the exergy efficiencies of biofuels are lower than the corresponding energetic efficiencies. For liquid biofuels, such as sludge and manure, gasification at the optimum point is not possible, and exergy efficiency can be improved by drying the biomass using the enthalpy of synthesis gas.     

Thermodynamic analysis of air-blown gasification for IGCC applications

This paper analyzes the thermodynamic performance of IGCC power plants based on an air-blown gasifier. A preliminary computational model for a lab-scale gasifier was calibrated on experimental data available in open literature, as a first step for the modeling of a large-scale MHI-type air-blown demonstration gasifier. The latter was analyzed by a parametric analysis, carried out by varying the gasification temperature and the heat transferred to the membrane walls. In agreement with data from MHI, the power balance of the air-blown gasifier suggests that the cold gas efficiency is similar to the one of oxygen-blown gasifiers, even though energy flows are quite different in the two gasification technologies.     

From coal to biomass gasification: Comparison of thermodynamic efficiency

The effect of fuel composition on the thermodynamic efficiency of gasifiers and gasification systems is studied. A chemical equilibrium model is used to describe the gasifier. It is shown that the equilibrium model presents the highest gasification efficiency that can be possibly attained for a given fuel. Gasification of fuels with varying composition of organic matter, in terms of O/C and H/C ratio as illustrated in a Van Krevelen diagram, is compared. It was found that exergy losses in gasifying wood (O/C ratio around 0.6) are larger than those for coal (O/C ratio around 0.2). At a gasification temperature of 927 °C, a fuel with O/C ratio below 0.4 is recommended, which corresponds to a lower heating value above 23 MJ/kg. For gasification at 1227 °C, a fuel with O/C ratio below 0.3 and lower heating value above 26 MJ/kg is preferred. It could thus be attractive to modify the properties of highly oxygenated biofuels prior to gasification, e.g. by separation of wood into its components and gasification of the lignin component, thermal pre-treatment, and/or mixing with coal in order to enhance the heating value of the gasifier fuel.     

Exergy analysis of renewable light olefin production system via biomass gasification and methanol synthesis

The conceptual light olefin production system from biomass via gasification and methanol synthesis was simulated and its thermodynamic performance was evaluated through exergy analysis. The system was made up of gasification, gas composition adjustment, methanol synthesis, light olefin synthesis, steam & power generation and cooling water treatment. The in-depth exergy analysis was performed at the levels of system, subsystem and operation component respectively. The gasifier and the tail gas combustor were the main sources of irreversibility with exergy destruction ratios of 17.0% and 16.8% of the input exergy of biomass. The steam & power generation subsystem accounted for 43.4% of the overall exergy destruction, followed by 41.0% and 5.69% in the subsystems of gasification and gas composition adjustment respectively. The sensitivity evaluation of the operation parameters of gasifier indicates that the system efficiency could be improved by enhancing syngas yield and subsequent yield of light olefins. The overall exergetic efficiency of 30.5% is obtained at the mass ratios of steam to biomass and O₂-rich gas (95 vol%) to biomass (S/B and O/B) of 0.26 and 0.14 and gasification temperature at 725 °C.     

Numerical Simulation of Pressure Effects on the Gasification of Australian and Indian Coals in a Tubular Gasifier

This article presents a numerical study on the effect of pressure on the gasification performance of an entrained flow tubular gasifier for Australian and Indian coals. Gasification using a substoichiometric amount of air, with or without steam addition, is considered. The model takes into account phenomena such as devolatilization, combustion of volatiles, char combustion, and gasification. Continuous-phase conservation equations are solved in an Eulerian frame and those of the particle phase are solved in a Lagrangian frame, with coupling between the two phases carried out through interactive source terms. The numerical results obtained show that the gasification performance increases for both types of coal when the pressure is increased. Locations of devolatilization, combustion, and gasification zones inside the gasifier are analyzed using the temperature plots, devolatilization plots, and mass depletion histories of coal particles. With increase in pressure, the temperature inside the gasifier increases and also the position of maximum temperature shifts upstream. For the high-ash Indian coal, the combustion of volatiles and char and the gasification process are relatively slower than those for the low-ash Australian coal. The mole fractions of CO and H₂ are found to increase with increase in pressure, in all the cases considered. Further, the effects of pressure on overall gasification performance parameters such as carbon conversion, product gas heating value, and cold gas efficiency are also discussed for both types of coals.     

Gasification of wood pellets in a bench-scale updraft gasifier

Biomass gasification is proving to be an alternative technology to the use of fossil fuels for energy production. The article considers the bench-scale, air-blown updraft gasification of biomass wood pellets. The objective of the study was to understand the characteristics of evolved gases from the gasifier that was built and assembled at the University Laboratory. Wood pellets of diameter 5 mm, length between 5 and 20 mm constitute the feedstock used. The experimental investigation reveals the major gases produced are CO₂, CO, and H₂, while CH₄ and other hydrocarbons are minor. However, the gasifier used is initially preheated to a temperature of about 800°C. This is indicated by the thermo-couple readings (T1–T8) with T6 as the standard thermo-couple. When T6 attains a steady state at 800°C, the gasifier is turned into a self-sustaining gasification condition. The entire experiment takes about four (4) hours to complete and this gives an understanding of evolved gases from the entire gasification process in the inside of the batch-scale updraft gasifier.     

Exergy analysis of biomass-to-synthetic natural gas (SNG) process via indirect gasification of various biomass feedstock

This paper presents an exergy analysis of SNG production via indirect gasification of various biomass feedstock, including virgin (woody) biomass as well as waste biomass (municipal solid waste and sludge). In indirect gasification heat needed for endothermic gasification reactions is produced by burning char in a separate combustion section of the gasifier and subsequently the heat is transferred to the gasification section. The advantages of indirect gasification are no syngas dilution with nitrogen and no external heat source required. The production process involves several process units, including biomass gasification, syngas cooler, cleaning and compression, methanation reactors and SNG conditioning. The process is simulated with a computer model using the flow-sheeting program Aspen Plus. The exergy analysis is performed for various operating conditions such as gasifier pressure, methanation pressure and temperature. The largest internal exergy losses occur in the gasifier followed by methanation and SNG conditioning. It is shown that exergetic efficiency of biomass-to-SNG process for woody biomass is higher than that for waste biomass. The exergetic efficiency for all biomass feedstock increases with gasification pressure, whereas the effects of methanation pressure and temperature are opposite for treated wood and waste biomass.     

Numerical modeling of a steam-assisted tubular coal gasifier

Understanding the heat and mass transfer phenomena in a coal gasifier is very useful for the assessment of gasifier performance and optimization of the design and operating parameters. In this paper, performance of an entrained flow air blown laboratory scale gasifier is numerically simulated with Fluent software. In the model, the continuous phase conservation equations are solved in an Eulerian frame, while those of particle phase are solved in a Lagrangian frame, with coupling between the two phases carried out through interactive source terms. The dispersion of the particles due to turbulence is predicted using a stochastic tracking model, in conjunction with the k–ε equations for the gas phase. The coal gasification model adopted includes devolatilization, combustion of volatiles, char combustion and gasification. The gasification performance inside the gasifier has been predicted for different air ratios as well as for different air and steam inlet temperatures. The overall temperature inside the gasifier is found to increase when the degree of air/steam pre-heating is increased, resulting in acceleration of the different reaction steps in the gasifier. The overall gasification performance indices such as carbon conversion, heating value of the exit gas and cold gas efficiency have been predicted. The predicted results show good agreement with available experimental data in literature.     

Effects of torrefaction on the physiochemical properties of oil palm empty fruit bunches,mesocarp fiber and kernel shell

In this work, the effects of torrefaction on the physiochemical properties of empty fruit bunches (EFB), palm mesocarp fiber (PMF) and palm kernel shell (PKS) are investigated. The change of properties of these biomass residues such as CHNS mass fraction, gross calorific value (GCV), mass and energy yields and surface structure when subjected to torrefaction process are studied. In this work, these materials with particle size in the range of 355–500 μm are torrefied under light torrefaction conditions (200, 220 and 240 °C) and severe torrefaction conditions (260, 280 and 300 °C). TGA is used to monitor the mass loss during torrefaction while tube furnace is used to produce significant amount of products for chemical analyses. In general, the study reveals torrefaction process of palm oil biomass can be divided into two main stages through the observation on the mass loss distribution. The first stage is the dehydration process at the temperature below than 105 °C where the mass loss is in the range of 3–5%. In the second stage, the decomposition reaction takes place at temperature of 200–300 °C. Furthermore, the study reveals that carbon mass fraction and gross calorific value (GCV) increase with the increase of torrefaction temperature but the O/C ratio, hydrogen and oxygen mass fractions decrease for all biomass. Among the biomass, torrefied PKS has the highest carbon mass fraction of 55.6% when torrefied at 300 °C while PMF has the highest GCV of 23.73 MJ kg⁻¹ when torrefied at the same temperature. Both EFB and PMF produce lower mass fraction than PKS when subjected to same torrefaction temperature. In terms of energy yield, PKS produces 86–92% yield when torrefied at light to severe torrefaction conditions, until 280 °C. However, both EFB and PMF only produce 70–78% yield at light torrefaction conditions, until 240 °C. Overall, the mass loss of 45–55% of these biomasses is observed when subjected to torrefaction process. Moreover, SEM images reveal that torrefaction has more severe impact on surface structure of EFB and PMF than that of PKS especially under severe torrefaction conditions. The study concludes that the torrefaction process of these biomass has to be optimized based on the type of the biomass in order to offset the mass loss of these materials through the process and increase the energy value of the solid product.     

Efficiency assessment of an integrated gasifier/boiler system for hydrogen production with different biomass types

In this study, we utilize some experimental data taken from the literature, especially on the air-blown gasification characteristics of six different biomass fuels, namely almond shell (ASF), walnut pruning (WPF), rice straw (RSF), whole tree wood chips (WWF), sludge (SLF) and non-recyclable waste paper (NPF) in order to study the thermodynamic performance of an integrated gasifier–boiler power system for its hydrogen production. In this regard, both energy and exergy efficiencies of the system are investigated. The exergy contents of different biomass fuels are calculated to be ranging from 15.89 to 22.07 MJ/kg, respectively. The hydrogen concentrations based on the stack gases at the cyclone exit are determined to be between 7 and 18 (%v/v) for NPF and ASF. Also, percentages of combustible vary from 30% to 46%. The stack gas has physical and chemical exergies. The total specific exergy rates are calculated and illustrated. These values change from 3.54 to 6.41 MJ/kg. Then, two types of exergy efficiencies are calculated, such as that exergy efficiency 1 is examined via all system powers, exergy and efficiency 2 is calculated according to specific exergy rates of biomass fuels and product gases. While the exergy efficiencies 1 change between 4.33% and 11.89%, exergy efficiencies 2 vary from 18.33% to 39.64%. Also, irreversibilities range from 9.76 to 18.02 MJ/kg. Finally, we investigate how nitrogen contents of biomass fuels affect on energy and exergy efficiencies. The SLF has the highest amount of nitrogen content as 5.64% db while the NPF has the lowest one as 0.14% db. The minimum and maximum exergetic efficiencies belong to the same fuels. Obviously, the higher the nitrogen content the lower the efficiency based on an inverse ratio between exergy efficiency and nitrogen content.     

First and second law thermodynamic analysis of a single and dual-stage ignition biomass downdraft gasifier

The dual-stage ignition biomass downdraft gasifier is an enormous tar reduction technology as against a single-stage ignition biomass gasification. Exergetic analysis of the system guides toward a possible performance enhancement. In dual-stage gasification, around 67.76% of input exergy is destructed in the several components, while 9.16% is obtained as a useful exergy output and 24.34% is found to be as a useful energy output there. The entire unit was assessed with a progressively rising electric load from 15.24 kW to 38.86 kW. The enhanced producer gas quality comes from 57% combustible gas with a higher heating value of 6.524 MJ/Nm³ and tar content of 7 mg/Nm³ after the paper filter, whereas the biomass consumption rate is 58 kg/h at the greatest load with the grate temperature of 1310–1370 °C. The samples of exhaust gas emissions are obtained environmentally favorable. The results even described that the dual-stage ignition biomass downdraft gasifier has significantly greater energetic and exergetic efficiency as compared to the single-stage gasifier.     

Isothermal and non-isothermal kinetic study on CO2 gasification of torrefied forest residues

CO₂ gasification of torrefied forest residues (birch and spruce branches) was investigated by means of a thermogravimetric analyser operated non-isothermally (400–1273 K) and isothermally (1123 K) under the kinetic regime, followed by kinetic analyses assuming different models. For the non-isothermal gasification, the distributed activation energy model (DAEM) with four or five pseudo-components was assumed. It is found that the severity level of torrefaction had great influences on gasification behaviour as well as devolatilization step. The activation energy of non-isothermal gasification step of three samples varied in the range of 260–290 kJ/mol. The char reactivity decreased with increased torrefaction temperature. For the isothermal gasification, the random pore model (RPM), shrinking core model (SCM), and homogeneous model (HM) were tested. The result has confirmed the trend of decrease in char reactivity with increased torrefaction temperature observed from the non-isothermal gasification. However, different trends in char reactivity due to different wood types were observed by the two methods of gasification.     

Engineered pellets from dry torrefied and HTC biochar blends

Dry torrefaction and hydrothermal carbonization (HTC) are two thermal pretreatment processes for making homogenized, carbon rich, hydrophobic, and energy dense solid fuel from lignocellulosic biomass. Pellets made from torrefied biochar have poor durability compared to pellets of raw biomass. Durability, mass density, and energy density of torrefied biochar pellets decrease with increasing dry torrefaction temperature. Durable pellets of torrefied biochar may be engineered for high durability using HTC biochar as a binder. In this study, biomass dry torrefied for 1 h at 250, 275, 300, and 350 °C was pelletized with various proportions of biomass HTC treated at 260 °C for 5 min. During the pelletization of biochar blends, HTC biochar fills the void spaces and makes solid bridges between torrefied biochar particles, thus increasing the durability of the blended pellets. The engineered pellets' durability is increased with increasing HTC biochar fraction. For instance, engineered pellets of 90% Dry 300 and 10% HTC 260 are 82.5% durable, which is 33% more durable than 100% Dry 300 biochar pellets, and also have 7% higher energy density than 100% Dry 300 biochar pellets.     

Coal conversion submodels for design applications at elevated pressures. Part II. Char gasification

This paper surveys the database on char gasification at elevated pressures, first, to identify the tendencies that are essential to rational design of coal utilization technology, and second, to validate a gasification mechanism for quantitative design calculations. Four hundred and fifty-three independent tests with 28 different coals characterized pressures from 0.02 to 3.0 MPa, CO₂ and steam mole percentages from 0 to 100%, CO and H₂ levels to 50%, gas temperatures from 800 to 1500 °C, and most of coal rank spectrum. Only a handful of cases characterized inhibition by CO and H₂, and only a single dataset represented the complex mixtures of H₂O, CO₂, CO, and H₂ that arise in practical applications. With uniform gas composition, gasification rates increase for progressively higher pressures, especially at lower pressures. Whereas the pressure effect saturates at the higher pressures with bituminous chars, no saturation is evident with low-rank chars. With fixed partial pressures of the gasification agents, the pressure effect is much weaker. Gasification rates increase for progressively higher gas temperatures. In general, gasification rates diminish for coals of progressively higher rank, but the data exhibit this tendency only for ranks of hv bituminous and higher.

These tendencies are interpreted with CBK/G, a comprehensive gasification mechanism based on the Carbon Burnout Kinetics Model. CBK/G incorporates three surface reactions for char oxidation plus four reactions for gasification by CO₂, H₂O, CO and H₂. Based on a one-point calibration of rate parameters for each coal in the database, CBK/G predicted extents of char conversion within ±11.4 daf wt% and gasification rates within ±22.7%. The predicted pressure, temperature, and concentration dependencies and the predicted inhibiting effects of CO and H₂ were generally confirmed in the data evaluations. The combination of the annealing mechanism and the random pore model imparts the correct form to the predicted rate reductions with conversion. CBK/G in conjunction with equilibrated gas compositions accurately described the lone dataset on complex mixtures with all the most important gasification agents, but many more such datasets are needed for stringent model evaluations.

Practical implications are illustrated with single-particle simulations of various coals, and a 1D gasifier simulation for realistic O₂ and steam stoichiometries. The rank dependence of gasification rates is the determining factor for predicted extents of char conversion at the gasifier outlet. But soot gasification kinetics will determine the unburned carbon emissions for all but the highest rank fuels. Only gasification kinetics for gas mixtures with widely variable levels of H₂O, H₂, and CO are directly relevant to gasifier performance evaluations.     

空气鼓风流化床煤部分气化炉煤气成分与热值试验

在内径100mm，高4．2m的常压流化床气化炉试验装置上进行试验，考察了气化炉温度，空煤比，汽煤比等影响因素对煤气成分和热值的影响，并对其气化机理进行了分析。结果表明，流化床煤部分气化炉内存在较佳气化温度，汽煤比和空煤比区域。图7表3参4