Synthesis of TiO<Subscript>2</Subscript> films on glass slides by the sol-gel method and their photocatalytic activity

Titanium dioxide (TiO₂) films with rod-like and sphere-like TiO₂ particles were prepared on glass slides employing the sol-gel method. The shape and size of TiO₂ particles were controlled using different concentrations of sodium dodecylbenzensulfonate (SDBS). By increasing the mole ratio of SDBS, the shape of TiO₂ particles transformed from rod-like to sphere-like. Also, the size of TiO₂ particles became gradually smaller. Then, the size became bigger when an excess amount of SDBS was added. The films were mainly composed of anatase titania and the relative content of anatase increased with the increasing amount of SDBS. The photocatalytic activity of the TiO₂ films that were added with SDBS was higher than that without SDBS. When the concentration of SDBS was 8.0 at%, the sample exhibited the best photocatalytic activity.     

Production of TiO<Subscript>2</Subscript> from CaTiO<Subscript>3</Subscript> by alkaline roasting method

CaTiO3 was decomposed by alkaline roasting method for the production of TiO2.The process included alkaline roasting, water leaching and acid leaching steps.In the alkaline roasting step, the factors such as roasting temperature and NaOH/CaTiO3 molar ratio were investigated and 99.5% TiO2 could be extracted from CaTiO3.In addition, it is believed that only ion-exchange between Ca2+ and Na+ takes place, while the structure of TiO 32-in CaTiO3 was not destroyed during the roasting process.In the acid leaching ...     

Hetero-Orientation Epitaxial Growth of TiO<Subscript>2</Subscript> Splats on Polycrystalline TiO<Subscript>2</Subscript> Substrate

In the present study, the effect of titania (TiO₂) substrate grain size and orientation on the epitaxial growth of TiO₂ splat was investigated. Interestingly, the splat presented comparable grain size with that of substrate, indicating the hereditary feature of grain size. In addition, hetero- and homo-orientation epitaxial growth was observed at deposition temperatures below 400 °C and above 500 °C, respectively. The preferential growth of high-energy (001) face was also observed at low deposition temperatures (≤?400 °C), which was found to result from dynamic nonequilibrium effect during the thermal spray deposition. Moreover, thermal spray deposition paves the way for a new approach to prepare high-energy (001) facets of TiO₂ crystals.     

Characteristics of hemocompatible TiO<Subscript>2</Subscript> nano-films produced by the sol-gel and anodic oxidation techniques

Hemocompatible films can be obtained by different techniques which must produce a smooth surface and a desired combination of crystal structure including rutile and anatase structures. Two of the simplest techniques include sol-gel and anodic oxidation. The characteristics of the films associated with the process variables are presented. The most important characteristics of the films are thickness, structure, roughness, and mechanical properties such as adhesion and wear resistance.     

Photoresponse and donor concentration of plasma-sprayed TiO<Subscript>2</Subscript> and TiO<Subscript>2</Subscript>-ZnO electrodes

The photoelectrochemical characteristics of plasma-sprayed porous TiO₂, TiO₂-5%ZnO, and TiO₂-10%ZnO electrodes in 0.1 N NaOH solution were studied through a three-electrode cell system. The microstructure, morphology, and composition of the electrodes were analyzed using an electron probe surface roughness analyzer (ERA-8800FE), scanning electron microscopy, and x-ray diffraction. The results indicate that the sprayed electrodes have a porous microstructure, which is affected by the plasma spray parameters and composition of the powders. The TiO₂-ZnO electrodes consist of anatase TiO₂, rutile TiO₂, and Zn₂Ti₃O₈ phase. The photoresponse characteristics of the plasma-sprayed electrodes are comparable to those of single-crystal TiO₂, but the breakdown voltage is close to 0.5 V (versus that of a saturated calomel electrode). The short-circuit photocurrent density (J _SC) increases with a decrease of donor concentration, which was calculated according to the Gartner-Butler model. For the lowest donor concentration of a TiO₂-5%ZnO electrode sprayed under an arc current of 600 A, the short-circuit J _SC is approximately 0.4 mA/cm² higher than that of the TiO₂ electrodes under 30 mW/cm² xenon light irradiation. The J _SC increases linearly with light intensity. The original version of this paper was published as part of the DVS Proceedings: “Thermal Spray Solutions: Advances in Technology and Application,” International Thermal Spray Conference, Osaka, Japan, 10–12 May 2004, CD-Rom, DVS-Verlag GmbH, Düsseldorf, Germany.     

Superior performance of high-velocity oxyfuel-sprayed nanostructured TiO<Subscript>2</Subscript> in comparison to air plasma-sprayed conventional Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-13TiO<Subscript>2</Subscript>

Air plasma-sprayed conventional alumina-titania (Al₂O₃-13wt.%TiO₂) coatings have been used for many years in the thermal spray industry for antiwear applications, mainly in the paper, printing, and textile industries. This work proposes an alternative to the traditional air plasma spraying of conventional aluminatitania by high-velocity oxyfuel (HVOF) spraying of nanostructured titania (TiO₂). The microstructure, porosity, hardness (HV 300 g), crack propagation resistance, abrasion behavior (ASTM G65), and wear scar characteristics of these two types of coatings were analyzed and compared. The HVOF-sprayed nanostructured titania coating is nearly pore-free and exhibits higher wear resistance when compared with the air plasma-sprayed conventional alumina-titania coating. The nanozones in the nanostructured coating act as crack arresters, enhancing its toughness. By comparing the wear scar of both coatings (via SEM, stereoscope microscopy, and roughness measurements), it is observed that the wear scar of the HVOF-sprayed nanostructured titania is very smooth, indicating plastic deformation characteristics, whereas the wear scar of the air plasma-sprayed alumina-titania coating is very rough and fractured. This is considered to be an indication of a superior machinability of the nanostructured coating.     

Preparation and magnetic properties of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> microtubules prepared by sol-gel template method

Fe(OH)₃ precursor sol was prepared by a sol-gel method. The precursor sol was dipped onto the absorbent cotton, and gel was formed on the absorbent cotton template after the volatilization of moisture. Fe₂O₃ microtubules were synthesized after the process of self-propagation or calcination. The phase, morphology, and particle diameter of the samples were examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM), and the magnetic properties of the samples were measured using a vibrating sample magnetometer (VSM). The external diameters of Fe₂O₃ microtubules ranged between 8 and 13 μm, and the wall thicknesses ranged between 0.5 and 2 μm. The type of the calcination method plays a significant role in developing the Fe₂O₃ phase and the variation in the magnetic properties in the sol-gel template complexing method. γ-Fe₂O₃ was synthesized by a self-propagation method. However, α-Fe₂O₃ was synthesized after calcination at 400°C for 2 h. The coercivity of the samples synthesized by calcination at 400°C for 2 h after self-propagation was found to increase significantly, thereby presenting hard magnetic properties.     

Luminescence properties of red-emitting Ca<Subscript>2</Subscript>Al<Subscript>2</Subscript>SiO<Subscript>7</Subscript>:Eu<Superscript>3+</Superscript> nanoparticles prepared by sol-gel method

A series of red-emitting Ca2-xAl2SiO7:xEu3+(x = 1 mol.%-10 mol.%) phosphors were synthesized by the sol-gel method.The effects of annealing temperature and doping concentration on the crystal structure and luminescence properties of Ca2Al2SiO7:Eu3+ phosphors were investigated.X-ray diffraction(XRD) profiles showed that all peaks could be attributed to the tetragonal Ca2Al2SiO7 phase when the sample was annealed at 1000℃.Scanning electron microscopy(SEM) micrographs indicate that the phosphors have an irregularly rounded morphology with particles of about 200 nm.Excitation spectra showed that the strong broad band at around 258 nm and weak sharp lines in 350-490 nm were attributed to the charge transfer band of Eu3+-O2-and f-f transitions within the 4f6 configuration of Eu3+ ions,respectively.Emission spectra implied that the red luminescence could be attributed to the transitions from the 5D0 excited level to the 7FJ(J = 0,1,2,3,4) levels of Eu3+ ions with the main electric dipole transition 5D0→7F2(618 and 620 nm),and Eu3+ ions prefer to occupy a lower symmetry site in the crystal lattice.Moreover,the photoluminescence(PL) intensity was strongly dependent on both the sintering temperature and doping concentration,and the highest PL intensity was observed at an Eu3+ concentration x = 7 mol.% after annealing at 1100℃.The obtained Ca2Al2SiO7:Eu3+ phosphor may have potential application for the red lamp phosphor.     

Preparation of TiO<Subscript>2</Subscript> Nanopowders by Plasma Spray and Characterizations

TiO₂ powders with the range of 10-60 nm were prepared successfully by plasma spray in the self-developed plasma spray equipment. The prepared nanopowders were characterized by transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The results showed that the prepared TiO₂ nanopowders were the mixture of anatase phase and rutile phase, the main phase was anatase. There were O, Ti, and C elements in powders; Ti element still existed in tetravalent. The photocatalytic degradation of methyl orange indicated that all methyl orange (20 mg/L) can be degraded fully when the addition of prepared TiO₂ nanopowders and illumination time were 1 g/L and 150 min, respectively.     

Effects of defects generated in ALD TiO<Subscript>2</Subscript> films on electrical properties and interfacial reaction in TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript>/Si system upon annealing in vacuum

Thin TiO₂ layers grown at 130°C on SiO₂-coated Si substrates by atomic layer deposition (ALD) using TTIP and H₂O as precursors were annealed, and the effects of the annealing temperature on the resulting electrical properties of TiO₂ and the interface properties between a Pt electrode and TiO₂ were examined using transmission line model (TLM) structures. The as-deposited TiO₂ thin film had an amorphous structure with OH groups and a high resistivity of 6×10³Ω-cm. Vacuum annealing at 700 °C transformed the amorphous film into an anatase structure and reduced its resistivity to 0.04Ω-cm. In addition, the vacuum-annealing of the TiO₂/SiO₂ structure at 700°C produced free silicon at the TiO₂-SiO₂ interface as a result of the reaction between the Ti interstitials and SiO₂. The SiO₂ formed on the TiO₂ surface caused a Schottky contact, which was characterized by the TLM method. The use of the TLM method enabled the accurate measurement of the resistivity of the vacuum-annealed TiO₂ films and the characterization of the Schottky contacts of the metal electrode to the TiO₂.     

Preparation and properties of a nano TiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> composite superparamagnetic photocatalyst

Nano TiO₂/Fe₃O₄ composite particles with different molar ratios of TiO₂ to Fe₃O₄ were prepared via sol-gel method. X-ray diffraction, transmission electron microscopy, and vibration sample magnetometry were used to characterize the TiO₂/Fe₃O₄ particles. The photocatalytic activity of the particles was tested by degrading methyl blue solution under UV illumination (254 nm). The results indicate that with the content of TiO₂ increasing, the photocatalytic activity of the composite particles enhances, while the magnetism of the particles decreases. When the molar ratio of TiO₂ to Fe₃O₄ is about 8, both the photocatalytic activity and magnetism of the TiO₂/Fe₃O₄ particles are relatively high, and their photocatalytic activity remains well after repeated use.     

Dielectric properties of Ta<Subscript>2</Subscript>O<Subscript>5</Subscript> thin films deposited onto Ti and TiO<Subscript>2</Subscript> layer

The present study describes the dielectric properties of RF sputtered Ta₂O₅ thin films as a function of the buffer layer and annealing condition. The buffer layers were Ti or TiO₂. And the thin film was annealed in various conditions. The X-ray pattern results showed that the phase of the RF sputtered Ta₂O₅ thin films was amorphous and this state was kept stable to RTA (rapid thermal annealing) even at 700°C. Measurements of the electrical and dielectric properties of the reactive sputtered Ta₂O₅ fabricated in two simple metal insulator semiconductor (MIS) structures, (Cu/Ta₂O₅/Ti/Si/Cu and Cu/Ta₂O₅/TiO₂/Si/Cu) indicated that the amorphous Ta₂O₅ grown on Ti possesses a high dielectric constant (30–70) and high leakage current (10⁻¹–10⁻⁴ A/cm²), whereas a relatively low dielectric constant (−10) and low leakage current (−10⁻¹⁰ A/cm²) were observed in the amorphous Ta₂O₅ deposited on the TiO₂ buffer layer. In addition, the leakage current mechanisms of the two amorphous Ta₂O₅ thin films were investigated by plotting the relation of current density (J) vs. applied electric field (E). The Ta₂O₅/Ti film exhibited three dominant conduction mechanism regimes contributed by the Ohmic emission at low electrical field, by the Schottky emission at intermediate field and by the Poole-Frenkel emission at high field. In the case of Ta₂O₅/TiO₂ film, the two conduction mechanisms, the Ohmic and Schottky emissions, governed the leakage current density behavior. The conduction mechanisms at various electric fields applied were related to the diffusion of Ta, Ti and O, followed by the creation of vacancies, in the rapid thermal treated capacitors.     

Effect of heat treatment in air on bonding strength and micro-structure of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-13 wt % TiO<Subscript>2</Subscript>/NiCrAl coating prepared by air plasma-spray process

According to the principle of plasma spraying, air plasma spraying Al₂O₃-13 wt % TiO₂/NiCrAl coating (AT13) on Q235 steel-substrate have some important disadvantages of high porosity, poor adhesive to substrate and low cohesive within the coating. Owing to such weaknesses, an enhancing densification and improving bonding of plasma-sprayed AT13 with an appropriate post air heat treatment is an effective method. On the basis of our final experimental results, post air heating treatment could improve the bonding strength and micro-structure of AT13. The AT13 shows the highest bonding strength and lowest Porosity when heating up to 560°C for 6 hours. Such performances may be because the re-crystallizing, reaction-diffusion of element diffusion and compressive stress of transitional layer. However, air heating temperature higher than 560°C led to the decline of the bonding strength. The excessive oxidizing products and compressive stress of oversized transitional layer could be contributed to the phenomenon.     

Interaction of stilbenes with TiO<Subscript>2</Subscript> studied by Fourier IR spectroscopy

Adsorption interactions of stilbene (1,2-diphenylethylene) and its hydroxy- and methoxyderivatives with nanodispersed TiO₂ aerogel surface were studied by means of Fourier IR radiosity spectroscopy. Stilbene trans- and cis-isomers were shown to be weakly adsorbed on TiO₂ surface forming hydrogen bonds. UV irradiation (wavelength 285–305 nm) of adsorbed compounds results in their partial destruction, yielding aldehydes, ketones, and carboxylates. The products of stilbene photolysis are strongly bound to TiO₂ surface. Modification of TiO₂ surface with trans-hydroxystilbenes is characterized by the formation of various hydrogen bonds and surface colored quinoid compounds. The interaction of TiO₂ with trans-methoxystilbenes changes the state of surface hydroxyl groups and yields stable carboxylate compounds. UV irradiation results in the partial destruction of adsorbed stilbenoids, yielding aldehyde, ketone, and carboxylate surface compounds.     

Enhanced properties of nanostructured TiO<Subscript>2</Subscript>-graphene composites by rapid sintering

Despite of many attractive properties of TiO₂, the drawback of TiO₂ ceramic is low fracture toughness for widely industrial application. The method to improve the fracture toughness and hardness has been reported by addition of reinforcing phase to fabricate a nanostructured composite. In this regard, graphene has been evaluated as an ideal second phase in ceramics. Nearly full density of nanostructured TiO₂-graphene composite was achieved within one min using pulsed current activated sintering. The effect of graphene on microstructure, fracture toughness and hardness of TiO₂-graphene composite was evaluated using Vickers hardness tester and field emission scanning electron microscopy. The grain size of TiO₂ in the TiO₂-x vol% (x = 0, 1, 3, and 5) graphene composite was greatly reduced with increase in addition of graphene. Both hardness and fracture toughness of TiO₂-graphene composites simultaneously increased in the addition of graphene.     

Electrophoretic impregnation of porous anodizing layer by synthesized TiO<Subscript>2</Subscript> nanoparticles

This paper deals with the elaboration of a stable suspension of TiO₂ nanoparticles and their incorporation by electrophoretic deposition into pores of an anodized 5754 aluminum alloy. The as-synthesized TiO₂ nanopowder was characterized by the X-ray diffraction, scanning and transmission electron microscopy, energy dispersive X-ray spectroscopy and IR spectroscopy. During this work, both the transmission electron microscopy and particle analysis showed that the resulting particles had a narrow size distribution with a crystallite size of about 15 nm. The zeta potential and stability of TiO₂ nanoparticles dispersed with poly(acrylic acid) in an aqueous solution were also measured. A porous anodic film was synthesized in the phosphoric acid-base electrolyte and then filled by 15 nm TiO₂ particles via electrophoresis. In addition, the effect of poly(acrylic acid) and pH on the suspension stability has been investigated. It was also demonstrated that by adding glycine in buffered suspension gelating phenomenon can be avoided that inhibits the insertion of nanoparticles inside the pores of an anodic film. It was also noted that an applied electric field greatly influences the electrophoretic deposition process. The field emission gun-scanning electron microscopy observations showed that larger (125 nm in diameter) and linear (6 μm in length) pores are successfully filled in 5 min.     

Mechano-thermal treatment of TiO<Subscript>2</Subscript>-Al powder mixture to prepare TiAl/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite

In this research, a composite comprising an intermetallic matrix and dispersed Al₂O₃ particles was processed. A mixture of TiO₂ and Al was mechanically activated in the presence of a process control agent and/or without it, in a high-energy planetary ball mill. As a subsequent process, the sample was sintered at various temperatures. The phase composition and morphology of the samples were evaluated by XRD and SEM techniques, respectively. The thermal behavior of the samples milled for 8 h with PVA and/or without it, were also assessed by the DTA technique and compared with one another. The DTA results revealed that addition of PVA shifted the aluminothermic reduction of TiO₂ to higher temperatures; therefore, final composite phases were developed at higher temperatures. The results also showed that addition of PVA during milling caused the final microstructure to coarsen. The XRD pattern of the sample sintered at 700 °C exhibits the existence of TiAl, Ti₃Al, and Al₂O₃ phases. In the sample sintered at 850 °C, the remaining Ti₃Al peak was attenuated and completely disappeared at 1000 °C.     

Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>-Deposit-Induced Corrosion of Mo-Containing Alloys

Disk alloys used in advanced gas turbine engines often contain significant amounts of Mo (2 wt% or greater), which is known to cause corrosion under Type I hot corrosion conditions (at temperatures around 900 °C) due to alloy-induced acidic fluxing. The corrosion resistance of several model and commercial Ni-based disk alloys with different amounts of Mo with and without Na₂SO₄ deposit was examined at 700 °C in air and in SO₂-containing atmospheres. When coated with Na₂SO₄ those alloys with 2 wt% or more Mo showed degradation products similar to those observed previously in Mo-containing alloys, which undergo alloy-induced acidic fluxing Type I hot corrosion even though the temperatures used in the present study were in the Type II hot corrosion range. Extensive degradation was observed even after exposure in air. The reason for the observed degradation is the formation of sodium molybdate. Transient molybdenum oxide reacts with the sodium sulfate deposit to form sodium molybdate which is molten at the temperature of study, i.e., 700 °C, and results in a highly acidic melt at the salt alloy interface. This provides a negative solubility gradient for the oxides of the alloying elements, which results in continuous fluxing of otherwise protective oxides.     

Dielectric properties of ZrTiO<Subscript>4</Subscript> thin films synthesized by sol-gel method

ZrTiO₄ thin films were successfully prepared on Pt/Ti/SiO₂/Si(100) substrates by a sol-gel process and gel films were heat-treated at various temperatures. The surface morphology, crystal structure, and dielectric properties of the thin films were investigated. It was possible to obtain ZrTiO₄ phase at temperatures above 650 °C for 2 h, which is much lower than the bulk sintering temperature. The microstructure of well-crystallized ZrTiO₄ thin films was a fine-grained microstructure less than 70 nm in grain size and the surface morphology was smooth with 22.4 rms roughness. The dielectric constant and loss of ZrTiO₄ thin films were 38 and 0.006, respectively, for thin films with 450 nm thickness heat-treated at 900 °C for 2 h.     

Control of microwave dielectric properties in 0.42ZnNb<Subscript>2</Subscript>O<Subscript>6</Subscript>−0.58TiO<Subscript>2</Subscript> ceramics by the quantitative analysis of phase transition

Phase constitutions of ZnNb₂O₆−TiO₂ mixture ceramics were significantly changed according to the sintering temperature. Phase transition procedures and their effect on the microwave dielectric properties of 0.42ZnNb₂O₆−0.58TiO₂ were investigated using X-ray powder diffraction and a network analyzer. The fractions of the phases composing the mixture were calculated by measuring integral intensities of each reflection. The structural transitions in 0.42ZnNb₂O₆−0.58TiO₂ were interpreted as the association of two distinct steps: the columbite and rutile to ixiolite transition present at lower temperatures (900–950°C) and the ixiolite to rutile transition at higher temperatures (1150–1300°C). These transitions caused considerable variation of microwave dielectric properties. Importantly, τ_f was modified to around 0 ppm/°C in two sintering conditions (at 925°C for 2 hr and at 1300°C for 2 hr), by the control of phase constitution.