Graphene oxide reinforced chitosan/polyvinylpyrrolidone polymer bio‐nanocomposites

Bio‐nanocomposite films based on chitosan/polyvinylpyrrolidone (CS/PVP) and graphene oxide (GO) were processed using the casting/evaporation technique. It has been found that the three components of bio‐nanocomposites can be easily mixed in controlled conditions enabling the formation of thick films with high quality, smooth surface and good flexibility. Structural and morphological characterizations showed that the GO sheets are well dispersed in the CS/PVP blend forming strong interfacial interactions that provide an enhanced load transfer between polymer chains and GO sheets thus improving their properties. It has been found that the water resistance of the CS/PVP blend is improved, and the hydrolytic degradation is limited by addition of 0.75 and 2 wt % GO. The modulus, strength, elongation and toughness of the bio‐nanocomposites are together increased. Herein, the steps to form new bio‐nanocomposite films have been described, taking the advantage of the combination of CS, PVP and GO to design the aforementioned bio‐nanocomposite films, which allow to have extraordinary properties that would have promising applications as eventual packaging materials. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41042.     

Modification of structural,thermal, and electrical properties of PVA by addition of silicon carbide nanocrystals

SiC‐PVA nanocomposite films, synthesized using solution‐casting technique were structurally characterized using X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and Raman spectroscopy. Morphological studies of the SiC‐PVA nanocomposite films were carried out using Transmission electron microscopy (TEM) and Scanning electron microscopy (SEM). TEM analysis confirms that the size of SiC nanocrystals present in PVA matrix are 23 ± 9 nm, which is consistent with size calculated using XRD. SiC‐PVA nanocomposite films were further characterized for their thermal and electrical properties. Thermogravimetric/differential thermal analysis (TG/DTA) indicates that the char yield of nanocomposite films containing 3 wt % SiC nanocrystal is ～30% more than PVA. This increase in char yield is an indication of the potency of flame retardation of SiC‐PVA nanocomposite films. I‐V analysis reveals that Schottky mechanism is the dominant conduction mechanism which is responsible for the increase in conductivity of PVA with the addition of SiC nanocrystals. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42464.     

Film‐forming behavior and mechanical properties of colloidal silica/polymer latex blends with high silica load

In this article, silica sol (diameter: 8–100 nm) and polymer latex (T_g < 25°C) were mixed and dried at room temperature to prepare nanocomposite films with high silica load (≥50 wt %). Effects of silica size, silica load, and the T_g of the polymer on the film‐forming behavior of the silica/polymer latex blend were investigated. The transparency, morphology, and mechanical properties of the nanocomposite films were examined by UV–Vis spectroscopy, SEM, and nanoindentation tests, respectively. Transparent and crack‐free films were produced with silica loads as high as 70 wt %. Thirty nanometers was found to be the critical silica size for the evolution of film‐forming behavior, surface morphology, and mechanical properties. Colloidal silica particles smaller than this critical size act as binders to form strong silica skeleton. This gives the final silica/polymer nanocomposite film its porous surface and high mechanical strength. However, silica particles with sizes of 30 nm or larger tend to work as nanofillers rather than binders, causing poor mechanical strength. We also determined the critical silica load appeared for the mechanical strength of silica/polymer film at high silica load. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Mechanical and morphological properties of lyocell blends: Comparison with lyocell nanocomposites (I)

The mechanical properties and morphologies of polyblends of lyocell with three different fillers are compared. Poly(vinyl alcohol) (PVA), poly(vinyl alcohol‐co‐ethylene) (EVOH), and poly(acrylic acid‐co‐maleic acid) (PAM) were used as fillers in blends with lyocell produced through solution blending. The variations of their properties with polymer matrix filler content are discussed. The ultimate tensile strength of the PVA/lyocell blend is highest for a blend lyocell content of 30 wt %, and decreases as the lyocell content is increased up to 40 wt %. The ultimate tensile strengths of the EVOH/lyocell and PAM/lyocell blends are highest for a lyocell loading of 20 wt %, and decrease with the increasing filler content. The variations in the initial moduli of the blends with filler content are similar. Of the three blend systems, the blends with PVA exhibit the best tensile properties. Lyocell/organoclay hybrid films were prepared by the solution intercalation method, using dodecyltriphenylphosphonium–Mica (C₁₂PPh‐ Mica) as the organoclay. The variation of the mechanical tensile properties of the hybrids with the matrix polymer organoclay content was examined. These properties were found to be optimal for an organoclay content of up to 5 wt %. Even polymers with low organoclay contents exhibited better mechanical properties than pure lyocell. The addition of organoclay to lyocell to produce nanocomposite films was found to be less effective in improving its ultimate tensile strength than blending lyocell with the polymers. However, the initial moduli of the nanocomposites were found to be higher than those of the polyblend films. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Studies of chitosan. I. Preparation and characterization of chitosan/poly(vinyl alcohol) blend films

Various blending ratios of chitosan/poly (vinyl alcohol) (CS/PVA) blend films were prepared by solution blend method in this study. The thermal properties and chemical structure characterization of the CS/PVA blend films were examined by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), and Fourier transform infrared (FTIR). Based upon the observation on the DSC thermal analysis, the melting point of PVA is decreased when the amount of CS in the blend film is increased. The FTIR absorption characteristic is changed when the amount of CS in the blend film is varied. Results of X‐ray diffraction (XRD) analysis indicate that the intensity of diffraction peak at 19° of PVA becomes lower and broader with increasing the amount of CS in the CS/PVA blend film. This trend illustrates that the existence of CS decreases the crystallinity of PVA. Although both PVA and CS are hydrophilic biodegradable polymers, the results of water contact angle measurement are still shown as high as 68° and 83° for PVA and for CS films, respectively. A minimum water contact angle (56°) was observed when the blend film contains 50 wt % CS. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of graphene loading on thermomechanical properties of poly(vinyl alcohol)/starch blend

Polymer nanocomposites based on poly(vinyl alcohol) (PVA)/starch blend and graphene were prepared by solution mixing and casting. Glycerol was used as a plasticizer and added in the starch dispersion. The uniform dispersion of graphene in water was achieved by using an Ultrasonicator Probe. The composites were characterized by FTIR, tensile properties, X‐ray diffraction (XRD), thermal analysis, and FE‐SEM studies. FTIR studies indicated probable hydrogen bonding interaction between the oxygen containing groups on graphene surface and the –OH groups in PVA and starch. Mechanical properties results showed that the optimum loading of graphene was 0.5 wt % in the blend. XRD studies indicated uniform dispersion of graphene in PVA/starch matrix upto 0.5 wt % loadings and further increase caused agglomeration. Thermal studies showed that the thermal stability of PVA increased and the crystallinity decreased in the presence of starch and graphene. FE‐SEM studies showed that incorporation of graphene increased the ductility of the composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41827.     

A chitosan/poly(vinyl alcohol) nanocomposite film reinforced with natural halloysite nanotubes

Biodegradable polymer/clay nanocomposites have attracted tremendous attentions because of their excellent properties and ecofriendly advantages. In this article, a series of nanocomposite films were prepared by introducing of halloysite nanotubes (HTs) into chitosan (CS)/poly(vinyl alcohol) (PVA) matrix using the solution casting method, and the effect of HT as nanofillers on the properties of polymer/HT nanocomposites was explored. The results indicated that the tensile strength of CS/PVA/HT3 and elongation at break of CS/PVA/HT2 sharply increased by 39.72% and 26.14% in comparison with the pure CS/PVA film, respectively. The water resistance and thermal stability of polymer/HT nanocomposites were also improved compared with the pure CS/PVA film, but the optical property of the nanocomposite films was not affected by introducing HT into the CS/PVA matrix. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Cellulose Nanocrystals/ZnO as a Bifunctional Reinforcing Nanocomposite for Poly(vinyl alcohol)/Chitosan Blend Films: Fabrication,Characterization and Properties

In this study, cellulose nanocrystals/zinc oxide (CNCs/ZnO) nanocomposites were dispersed as bifunctional nano-sized fillers into poly(vinyl alcohol) (PVA) and chitosan (Cs) blend by a solvent casting method to prepare PVA/Cs/CNCs/ZnO bio-nanocomposites films. The morphology, thermal, mechanical and UV-vis absorption properties, as well antimicrobial effects of the bio-nanocomposite films were investigated. It demonstrated that CNCs/ZnO were compatible with PVA/Cs and dispersed homogeneously in the polymer blend matrix. CNCs/ZnO improved tensile strength and modulus of PVA/Cs significantly. Tensile strength and modulus of bio-nanocomposite films increased from 55.0 to 153.2 MPa and from 395 to 932 MPa, respectively with increasing nano-sized filler amount from 0 to 5.0 wt %. The thermal stability of PVA/Cs was also enhanced at 1.0 wt % CNCs/ZnO loading. UV light can be efficiently absorbed by incorporating ZnO nanoparticles into a PVA/Cs matrix, signifying that these bio-nanocomposite films show good UV-shielding effects. Moreover, the biocomposites films showed antibacterial activity toward the bacterial species Salmonella choleraesuis and Staphylococcus aureus. The improved physical properties obtained by incorporating CNCs/ZnO can be useful in variety uses.     

Preparation and characterization of polybutylene‐succinate/poly(ethylene‐glycol)/cellulose nanocrystals ternary composites

Ternary composites were prepared by twin screw extrusion from polybutylene‐succinate (PBS), poly(ethylene‐glycol) (PEG), and cellulose nanocrystals (CNC). The aim of the work is to improve the physical–mechanical properties of PBS by the addition of CNC. A PEG/CNC masterbatch was prepared in order to achieve a good dispersion of hydrophilic CNC in the hydrophobic PBS. The influence of the nanoparticle content on the polymer properties was studied. Regarding the thermal properties fractioned crystallization phenomena of PEG was observed during cooling from the melt. No significant nucleating effect of the nanocellulose was observed. The material containing 4 wt % of CNC showed the best mechanical performance among the nanocomposites studied due to the combination of high modulus and elongation at break with a low detrimental in strength compared with the PBS/PEG blend. Moreover, no nanocellulose agglomerations were observed in its FESEM micrograph. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43302.     

Fumed SiO2 nanoparticle reinforced biopolymer blend nanocomposites with high dielectric constant and low dielectric loss for flexible organic electronics

In the present study, fumed silica (SiO₂) nanoparticle reinforced poly(vinyl alcohol) (PVA) and poly(vinylpyrrolidone) (PVP) blend nanocomposite films were prepared via a simple solution‐blending technique. Fourier transform infrared spectroscopy (FTIR), ultraviolet–visible spectroscopy (UV–vis), X‐ray diffraction (XRD), and scanning electron microscopy (SEM) were employed to elucidate the successful incorporation of SiO₂ nanoparticles in the PVA/PVP blend matrix. A thermogravimetric analyzer was used to evaluate the thermal stability of the nanocomposites. The dielectric properties such as dielectric constant (?) and dielectric loss (tan δ) of the PVA/PVP/SiO₂ nanocomposite films were evaluated in the broadband frequency range of 10^?2 Hz to 20 MHz and for temperatures in the range 40–150 °C. The FTIR and UV–vis spectroscopy results implied the presence of hydrogen bonding interaction between SiO₂ and the PVA/PVP blend matrix. The XRD and SEM results revealed that SiO₂ nanoparticles were uniformly dispersed in the PVA/PVP blend matrix. The dielectric property analysis revealed that the dielectric constant values of the nanocomposites are higher than those of PVA/PVP blends. The maximum dielectric constant and the dielectric loss were 125 (10^?2 Hz, 150 °C) and 1.1 (10^?2 Hz, 70 °C), respectively, for PVA/PVP/SiO₂ nanocomposites with 25 wt % SiO₂ content. These results enable the preparation of dielectric nanocomposites using a facile solution‐casting method that exhibit the desirable dielectric performance for flexible organic electronics. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44427.     

Preparation and characterization of poly(vinyl alcohol)‐based magnetic nanocomposites. 1. Thermal and mechanical properties

CoFe₂O₄ magnetic nanoparticles were prepared by in situ precipitation and oxidation of Co²⁺ and Fe²⁺ within a sulfonated polystyrene resin. The nanometric particles were characterized by X‐ray diffraction. A ferrofluid was prepared from the CoFe₂O₄ mineralized polymer resin and water. Poly(vinyl alcohol) (PVA)‐based nanocomposite materials were obtained by mixing different amounts of ferrofluid (compositions ranging within 0–51 wt % of mineralized resin) with an aqueous solution of the polymer. The PVA composite materials were characterized by TGA, DSC, and stress–strain testing. The thermal and mechanical properties of PVA change with filler content, exhibiting an initial increase in these properties due to polymer–filler interactions. After a maximum value, at about 15 wt % of mineralized resin, the mechanical properties decrease probably due to particle aggregation which causes phase separation. The results obtained show that the nanoparticles are dispersed in the amorphous regions of the polymer, the crystalline zones remaining unaltered up to compositions as high as 30 wt %. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3215–3222, 2001     

Enhancement of water barrier properties of cassava starch-based biodegradable films using silica particles

Biodegradable films are used in a variety of applications, including packaging. However, their use is limited due to their high moisture and water sensitivity. In this work, cassava starch (CS) was blended with poly(vinyl alcohol) (PVA). Silica particles (SiO₂) were incorporated to increase the hydrophobicity of the blend by intermolecular interaction through hydrogen bonding between the three components. Instead of a plasticizer or crosslinker, a small amount of triethylamine was added to eliminate residual acetate groups in PVA. The miscibility of CS and PVA phases was confirmed by smooth fracture surfaces and a single glass transition temperature. When SiO₂ content was below 5% (wt), the particles were well dispersed in a continuous phase of polymer matrix. At this loading of SiO₂, the increase in tensile strength was as high as 170% and in elongation-at-break, 250%. All loadings of SiO₂ increased thermal stability of the blend films because silanol groups on the surface of SiO₂ particles formed effective interfacial interactions with hydroxyl groups of the polymers. These interactions also prevented the ingress of water molecules, significantly increasing the hydrophobicity of the films. The water contact angle increased as high as 113° and moisture absorbency and water solubility were low. These highly hydrophobic, photodegradable, biodegradable CS/PVA/SiO₂ films show great potential as a low-cost, eco-friendly material.

     

Physicochemical and antibacterial properties of chitosan‐polyvinylpyrrolidone films containing self‐organized graphene oxide nanolayers

Chitosan films have a great potential to be used for wound dressing and food‐packaging applications if their physicochemical properties including water vapor permeability, optical transparency, and hydrophilicity are tailored to practical demands. To address these points, in this study, chitosan (CS) was combined with polyvinylpyrrolidone (PVP) and graphene oxide (GO) nanosheets (with a thickness of ～1 nm and lateral dimensions of few micrometers). Flexible and transparent films with a high antibacterial capacity were prepared by solvent casting methods. By controlling the evaporation rate of the utilized solvent (1 vol % acidic acid in deionized water), self‐organization of GO in the polymer matrix was observed. The addition of PVP to the CS/GO films significantly increased their water vapor permeability and optical transmittance. A blue shift in the optical absorption edge was also noticed. Thermal analysis coupled with Fourier transform infrared spectroscopy suggested that the superior thermal stability of the nanocomposite films was due to the formation of hydrogen bonds between the functional groups of chitosan with those of the graphene oxide. An improved bactericidal capacity of the nanocomposite films against gram‐positive Staphylococcus aureus and gram‐negative Escherichia coli bacteria was also observed. Highly flexible, transparent (opacity of 6.95), and antimicrobial CS/25 vol % PVP/1 wt % GO films were prepared. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43194.     

Poly(vinyl alcohol) nanocomposites with different clays: Pristine clays and organoclays

Poly(vinyl alcohol) (PVA)/clay nanocomposites were synthesized using the solution intercalation method. Na ion‐exchanged clays [Na⁺–saponite (SPT) and Na⁺–montmorillonite (MMT)] and alkyl ammonium ion‐exchanged clays (C₁₂–MMT and C₁₂OOH–MMT) were used for the PVA nanocomposites. From the morphological studies, the Na ion‐exchanged clay is more easily dispersed in a PVA matrix than is the alkyl ammonium ion‐exchanged clay. Attempts were also made to improve both the thermal stabilities and the tensile properties of PVA/clay nanocomposite films, and it was found that the addition of only a small amount of clay was sufficient for that purpose. Both the ultimate tensile strength and the initial modulus for the nanocomposites increased gradually with clay loading up to 8 wt %. In C₁₂OOH–MMT, the maximum enhancement of the ultimate tensile strength and the initial modulus for the nanocomposites was observed for blends containing 6 wt % organoclay. Na ion‐exchanged clays have higher tensile strengths than those of organic alkyl‐exchanged clays in PVA nanocomposites films. On the other hand, organic alkyl‐exchanged clays have initial moduli that are better than those of Na ion‐exchanged clays. Overall, the content of clay particles in the polymer matrix affect both the thermal stability and the tensile properties of the polymer/clay nanocomposites. However, a change in thermal stability with clay was not significant. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3208–3214, 2003     

A starch‐based biodegradable film modified by nano silicon dioxide

The purpose of this work was to improve the properties of the starch/poly(vinyl alcohol) (PVA) films with nano silicon dioxide (nano SiO₂). Starch/PVA/nano‐SiO₂ biodegradable blend films were prepared by a solution casting method. The characteristics of the films were assessed by Fourier Transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and X‐ray photoelectron spectroscopy (XPS). The results obtained in this study indicated that the nano‐SiO₂ particles were dispersed evenly within the starch/PVA coating and an intermolecular hydrogen bond and a strong chemical bond C? O? Si were formed in the nano‐SiO₂ and starch/PVA. That the blending of starch, PVA and nano‐SiO₂ particles led to uniform starch/PVA/nano‐SiO₂ blend films with better mechanical properties. In addition, the nano‐SiO₂ particles can improve the water resistance and light transmission of the blend films. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Sugarcane bagasse ash as a reinforcing filler in thermoplastic elastomers: Structural and mechanical characterizations

The incorporation of residues as reinforcing fillers in polymer composites has emerged as a viable solution, enabling improvements in the mechanical properties of these materials, and has also resulted in a reduction in the cost of the final product. In this work, sugarcane bagasse ash (SBA) was used as a reinforcing filler in comparison with commercial silica (CS) in thermoplastic elastomers prepared from the compatibility of low‐density polyethylene (LDPE) with natural rubber (NR). The composites were obtained by a physical mixture of LDPE and NR with different proportions of CS and SBA using a Haake rotational rheometer. The samples were analyzed by Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and tensile testing. The results show that SBA has similar properties to CS, thus making its use feasible as a reinforcing filler in thermoplastic elastomers. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41466.     

Cellulose nanocrystal‐based poly(butylene adipate‐co‐terephthalate) nanocomposites covered with antimicrobial silver thin films

In this study, we reported the preparation and prospective application of the nanocomposites of poly(butylene adipate‐co‐terephthalate) (PBAT) reinforced with cellulose nanocrystals (CNCs). CNCs were isolated from bleached sugarcane bagasse by acid hydrolysis and functionalized with adipic acid. Nanocomposites were prepared with different concentration of CNCs (0.8, 1.5, and 2.3 wt% CNC) by solution‐casting method and then were covered with silver thin film by magnetron sputtering. The results showed that the surface modification increased the degree of crystallinity of nanocrystals from 51% to 56%, decreasing their length and diameter. Moreover, AFM‐IR spectroscopy revealed that the modified CNCs were covered by adipic acid molecules, improving the dispersion of nanocrystals in PBAT. Well‐dispersed modified CNCs acted as heterogeneous nuclei for crystallization of PBAT, and increased the storage modulus of the polymer by more than 200%. These improvements in thermal and mechanical properties of CNC‐based PBAT associated with the decrease of 56% in the Escherichia coli biofilm formation on nanocomposites (antibacterial properties) qualify the CNC/PBAT nanocomposites covered with silver thin films to be used as food packaging. POLYM. ENG. SCI., 59:E356–E365, 2019. © 2019 Society of Plastics Engineers     

Water sorption and water‐resistance properties of poly(vinyl alcohol)/clay nanocomposite films: Effects of chemical structure and morphology

A series of poly(vinyl alcohol)/sodium montmorillonite (PVA/NaMMT) nanocomposite films were prepared via a solution method, and their water sorption and water‐resistant properties were investigated as a function of clay content. The water sorption and water resistance properties were strongly dependent on the chemical structure and film morphology originating from the NaMMT content. The water diffusion coefficient and water uptake of the PVA/NaMMT nanocomposite films were obtained by best fits to a Fickian diffusion model. The diffusion coefficient and water uptake in the PVA/NaMMT nanocomposite films varied between 8.16 × 10⁻¹⁰ and 3.60 × 10⁻¹⁰ cm² s⁻¹ and 35.6 and 29.9 wt%, respectively. Both the diffusion coefficient and water uptake decreased as the content of NaMMT in pure PVA was increased. Additionally, the water resistance pressure (mm) of the PVA/NaMMT nanocomposite films increased with increasing NaMMT content. Contact angle analyses showed that the chemical affinity to water and the surface energy of the nanocomposite films decreased with increasing NaMMT content. Furthermore, the well‐dispersed and exfoliated structure in the nanocomposite films not only induced an increased tortuous path for water molecules to pass through, but also increased the molecular order. However, to enhance the water sorption properties and water resistance of hydrophilic PVA, further studies to increase the dispersion of clay particles and ensure desired morphological qualities such as crystallinity and molecular packing order in the PVA/clay nanocomposite films are required. POLYM. COMPOS., 36:660–667, 2015. © 2014 Society of Plastics Engineers     

Development and compatibility assessment of new composite film based on sugar beet pulp and polyvinyl alcohol intended for packaging applications

In this study, interaction and compatibility between sugar‐beet pulp (SBP) and polyvinyl alcohol (PVA) in blend films was assessed. Film‐forming dispersions of different ratios of SBP to PVA (100/0, 75/25, 50/50, and 25/75) were cast at room temperature. The effects of adding PVA to SBP on the resulting film's physical, mechanical and barrier properties and thermal stability were investigated. X‐ray diffraction and environmental scanning electron microscopy (ESEM) were used to characterize the structure and morphology of the composites. When PVA was also added to the composite films, the films became softer, less rigid and more stretchable than pure SBP films. The addition of PVA gave significantly greater elongation at break (12.45%) and lower water vapor permeability (1.55 × 10^?10 g s^?1 m^?1 Pa^?1), but tensile strength did not markedly change, remaining around 59.68 MPa. Thermogravimetric analysis also showed that SBP/PVA film had better thermal stability than SBP film. The ESEM results showed that the compatibility of SBP50/PVA50 was better than those of other composite films. These results suggest that when taking all the studied variables into account, composite films formulated with 50% PVA are most suitable for various packaging applications. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41354.     

Melt processing of polyamide 12 and cellulose nanocrystals nanocomposites

The fabrication of nanocomposites of polyamide 12 (PA12) and cellulose nanocrystals (CNCs) isolated from cotton and tunicates is reported. Through a comparative study that involved solution‐cast (SC) and melt‐processed materials, it was shown that PA12/CNC nanocomposites can be prepared in a process that appears to be readily scalable to an industrial level. The results demonstrate that CNCs isolated from the biomass by phosphoric acid hydrolysis display both a sufficiently high thermal stability to permit melt processing with PA12, and a high compatibility with this polymer to allow the formation of nanocomposites in which the CNCs are well dispersed. Thus, PA12/CNC nanocomposites prepared by melt‐mixing the two components in a co‐rotating roller blade mixer and subsequent compression molding display mechanical properties that are comparable to those of SC reference materials. Young's modulus and maximum stress could be doubled in comparison to the neat PA12 by introduction of 10% (CNCs from tunicates) or 15% w/w (CNCs from cotton) CNCs. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42752.