Synergistic effect of THEIC‐Based charring agent on flame retardant properties of polylactide

A novel charring agent tris(2‐hydrooxyethyl) isocyanurate terephthalic acid ester, tetramer (TT4) was synthesized using tris(2‐hydrooxyethyl) isocyanurate and terephthalic acid as raw materials, and it was characterized by Fourier transformed infrared spectrometry and ¹H‐NMR spectrum. It was combined with ammonium polyphosphate (APP) to form intumescent flame retardants for polylactide (PLA). The combustion properties and thermal stability of PLA/APP/TT4 composites were evaluated by UL‐94 burning tests, limiting oxygen index (LOI), and thermogravimetric analyses (TGA). It was found PLA with 30 wt % of APP/TT4 (5 : 1) achieved UL‐94 V‐0 rating and a 40.6 LOI value. Results from TGA demonstrated that APP/TT4 composites could retard the degradation of PLA above 410°C. The char residue at 500°C is higher than 24%, showing a good char forming ability. Moreover, the continuous and expansionary char layer observed from the SEM images proved good charring forming ability of TT4. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41218.     

Flame‐retardancy properties of tris(2‐hydroxyethyl) isocyanurate based charring agents on polypropylene

Tris(2‐hydroxyethyl) isocyanurate based charring agent (TBCA) was synthesized by melt polycondensation with tris(2‐hydroxyethyl) isocyanurate (THEIC) and terephthalic acid as raw materials. It was characterized by Fourier transform infrared spectroscopy, elemental analysis, ¹H‐NMR, and thermogravimetric analysis (TGA). TBCA was blended with ammonium polyphosphate (APP) to form an intumescent flame retardant (IFR) for polypropylene (PP). The charring properties of TBCA was tested by flame retardancy in the PP/APP/TBCA (PP/IFR₂) composite and compared with that of the PP/APP/THEIC (PP/IFR₁) composite. The results show that PP/IFR₂ had lower flame‐retardant properties but better water resistance than that of the PP/IFR₁ composite because PP/IFR₂ could still obtain a V‐0 rating after it had been soaked in water at 70°C for 96 h, whereas PP/IFR₁ could not achieve any rating after 36 h. Their combustion performance was further evaluated by a cone calorimeter test, their thermal degradation processes were studied by TGA, and the morphology of the char residue was observed by scanning electron microscopy. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41810.     

Synthesis of tris(2‐hydroxyethyl) isocyanurate homopolymer and its application in intumescent flame retarded polypropylene

A macromolecular homopolymer (named as Homo‐THEIC) was synthesized through self‐etherification of tris(2‐hydroxyethyl) isocyanurate (THEIC) molecules and used as charring agent. Its chemical structure was characterized by FTIR and ¹³C‐NMR. The charring agent was mixed with ammonium polyphosphate (APP) and applied in flame retarded polypropylene (PP). Results of UL‐94, LOI, and cone calorimeter test showed that the LOI of flame retarded PP can reach 32.8% and UL‐94 V‐0 rating can be achieved at 30 wt % loading. The heat release rate and smoke production rate during the combustion of PP were substantially reduced. TGA results indicated that the synergistic effect between APP and Homo‐THEIC existed and the addition of intumescent flame retardant (IFR) dramatically enhanced the thermal stability of PP. According to the results of TGA, SEM, TG‐FTIR, FTIR, and Raman, the char forming process of IFR can be separated into three stages: the formation of viscous phosphate ester (T _onset?330 °C), the expanding process along with the decomposition of phosphate ester and the release of a large amount of gases (330–480 °C), and the final formation of graphitic‐like char without any expanding feature (480–670 °C). © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44663.     

Synergistic effect between aluminum hypophosphite and a new intumescent flame retardant system in poly(lactic acid)

A hyperbranched charring agent (CT) was synthesized by triglycidyl isocyanurate and diethylenetriamine in water, and a new intumescent flame retardant (IFR) system was formed by ammonium polyphosphate (APP) and CT. The different formula and synergistic system between IFR and aluminum hypophosphite (AHP) have been studied through limit oxygen index (LOI), UL‐94, cone calorimetry test and TGA. It was found that the LOI for poly(lactic acid) (PLA) with 30 APP/CT (4:1) and 20 wt % IFR/AHP (3:1) were 41.2% and 43.5%, respectively, and the both could achieve UL‐94V‐0 rating with no melt dripping. The heat release rate (HRR), maximum HRR value and average mass loss rate of PLA could be dramatically decreased by combination of IFR and AHP while the thermal stability was greatly enhanced. The study of morphology and structure of char illustrated that more intumescent and compact char layer with good intensity was formed during the degradation of IFR/AHP, which resulting to better flame retardancy and anti‐dripping than IFR or AHP alone. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46359.     

Synthesis of phospholipidated β‐cyclodextrin and its application for flame‐retardant poly(lactic acid) with ammonium polyphosphate

In this study, phospholipidated β‐cyclodextrin (PCD) was obtained by the condensation between β‐cyclodextrin and phenyl phosphonic acid dichloride, which was characterized by Fourier transform infrared (FTIR) spectra, ¹H‐NMR, and thermogravimetric analysis (TGA). The thermal stability and flame retardancy of the poly(lactic acid) (PLA) blends [PLA–ammonium polyphosphate (APP)–PCD] were measured by TGA coupled to FTIR spectroscopy, vertical burning test (UL‐94), limiting oxygen index (LOI), and cone calorimetry tests. The results show that the mass ratio and loading amount of APP and PCD affected the properties of PLA. When the loading of APP and PCD was 30 wt % and the mass ratio of APP to PCD was 5:1, the highest LOI value of 42.6% (that of neat PLA was 19.7%) and a UL‐94 V0 rating were achieved, and the reduction of the total heat release was greater than 80%. Even when the total amount of APP and PCD was decreased to 20 wt % with the same mass ratio, the flame‐retardant PLA still can achieved a UL‐94 V0 rating. The improved performance was explained by the formation of an intumescent, continuous, contact char layer. Moreover, the reaction between APP and PCD contributed to the improvement of the thermal stability of the char residue. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46054.     

Synergistic effect of a novel charring agent with ammonium polyphosphate on flame retardancy and thermal degradation of acrylonitrile‐butadiene‐styrene copolymer

A novel charring agent poly(1,3‐propylene terephthalamide) (PPTA) was synthesized and characterized by Fourier transform infrared spectroscopy and ¹H nuclear magnetic resonance. This novel charring agent combined with ammonium polyphosphate (APP) was adopted as an intumescent flame retardant (IFR) to impart flame retardance and dripping resistance to acrylonitrile‐butadiene‐styrene copolymer (ABS). Flammability and thermal behaviors of the treated ABS were investigated by limiting oxygen index, vertical burning test and thermogravimetric analysis. The results showed that the IFR with the novel charring agent had both excellent flame retardant and anti‐dripping abilities for ABS. The thermogravimetric analysis curves indicated that there was a synergistic effect between PPTA and APP, which greatly promoted the char formation of IFR‐ABS composites. Meanwhile, the thermal degradation mechanism of PPTA and APP/PPTA was characterized using thermogravimetric analysis/infrared spectrometry. The results demonstrated that APP changed the thermal degradation behavior of PPTA and reacted with PPTA to form a crosslinked structure. Additionally, the structure and morphology of char residues were studied by Fourier transform infrared spectroscopy and scanning electron microscopy. Copyright © 2011 Society of Chemical Industry     

Three in one: β‐cyclodextrin,nanohydroxyapatite, and a nitrogen‐rich polymer integrated into a new flame retardant for poly (lactic acid)

A new halogen‐free flame retardant was developed by integrating β‐cyclodextrin, triazin ring, and nanohydroxyapatite (BSDH) into a hybrid system. A β‐cyclodextrin was grafted to a commercially available SABO®STAB UV94 via an aromatic deanhydrate. The BSDH was prepared in situ in the presence of β‐cyclodextrin‐grafted nitrogen‐rich precursor. The resulting hybrid was applied as a flame retardant for poly(lactic acid) (PLA) and compared for performance with ammonium polyphosphate (APP). PLA composites containing BSDH and APP, individually or simultaneously, were examined for thermal degradation and flammability by TGA, cone calorimeter, and pyrolysis‐combustion flow calorimetry. TGA results confirmed enhancement of thermal stability of PLA with assistance of BSDH compared to APP. The gases evolved during thermal degradation were assessed by a thermogravimetric analysis and Fourier infrared spectroscopy device. APP revealed catalytic effect to initiate PLA degradation, while BSDH continued to release some gases at elevated temperatures. The flame retardancy of PLA/APP/BSDH blend containing only 10 wt.% of additives was significantly improved. In cone calorimetric tests, a significant fall in peak of heat release rate was observed for this sample, 49% more than that of neat PLA, which was indicative of more gas and condensed phase reflected in more char residue. The corresponding PLA/APP sample, however, showed 17% improvement, as compared to neat PLA. Also, total heat release rate of PLA/APP/BSDH was 45 MJ.m^?2, whereas those of PLA and PLA/APP were 89 and 65 MJ.m^?2, respectively. BSDH and APP showed a synergistic effect on improving the flame retardancy of PLA composites.     

Application of a novel halogen‐free intumescent flame retardant for acrylonitrile‐butadiene‐styrene

A novel intumescent flame retardant (IFR), containing ammonium polyphosphate (APP) and poly(tetramethylene terephthalamide) (PA4T), was prepared to flame‐retard acrylonitrile‐butadiene‐styrene (ABS). The flame retardation of the IFR/ABS composite was characterized by limiting oxygen index (LOI) and UL‐94 test. Thermogravimetric analysis (TGA) and TGA coupled with Fourier transform infrared spectroscopy (TG‐FTIR) were carried out to study the thermal degradation behavior of the composite and look for the mechanism of the flame‐retarded action. The morphology of the char obtained after combustion of the composite was studied by scanning electron microscopy (SEM). It has been found the intumescent flame retardant showed good flame retardancy, with the LOI value of the PA4T/APP/ABS (7.5/22.5/70) system increasing from 18.5 to 30% and passing UL‐94 V‐1 rating. Meanwhile, the TGA and TG‐FTIR work indicated that PA4T could be effective as a carbonization agent and there was some reaction between PA4T and APP, leading to some crosslinked and high temperature stable material formed, which probably effectively promoted the flame retardancy of ABS. Moreover, it was revealed that uniform and compact intumescent char layer was formed after combustion of the intumescent flame‐retarded ABS composite. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Modification of lignin and its application as char agent in intumescent flame‐retardant poly(lactic acid)

Urea‐modified lignin was prepared according to the Mannich reaction and well characterized by Fourier transform infrared spectrometer, elemental ananlyses, and scanning electron microscopy (SEM). Ammonium polyphosphate (APP) and urea‐modified lignin were added into poly(lactic acid) (PLA) as a novel intumescent flame‐retardant (IFR) system to improve flame retardancy of PLA. The flammability of IFR–PLA composites was studied using limiting oxygen index, UL‐94 vertical burning method and cone calorimeter test, and their thermal stability was evaluated by thermogravimetric analysis. The results showed that the urea‐modified lignin combined with APP exhibited much better flame retardancy and thermal stability than that of the combination of virgin lignin and APP. The improvement may be attributed to the better char morphology with more phosphoric char evidenced by SEM and X‐ray photoelectron spectroscopy. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Synthesis of novel triazine charring agent and its effect in intumescent flame‐retardant polypropylene

A novel charring agent (CNCA‐DA) containing triazine and benzene ring, using cyanuric chloride, aniline, and ethylenediamine as raw materials, was synthesized and characterized. The effects of CNCA‐DA on flame retardancy, thermal degradation, and flammability properties of polypropylene (PP) were investigated by limited oxygen index (LOI), vertical burning test (UL‐94), thermogravimetric analysis (TGA), and cone calorimeter test (CCT). The TGA results showed that CNCA‐DA had a good char forming ability, and a high initial temperature of thermal degradation; the char residue of CNCA‐DA reached 18.5% at 800°C; Ammonium polyphosphate (APP) could improve the char residue of APP/CNCA‐DA system, the char residue reached 31.6% at 800°C. The results from LOI and UL‐94 showed that the intumescent flame retardant (IFR) containing CNCA‐DA and APP was very effective in flame retardancy of PP. When the mass ratio of APP and CNCA‐DA was 2 : 1, and the IFR loading was 30%, the IFR showed the best effect; the LOI value reached 35.6%. It was also found that when the IFR loading was only 20%, the flame retardancy of PP/IFR can still pass V‐0 rating in UL‐94 tests, and its LOI value reached 27.1%. The CCT results demonstrated that IFR could clearly change the decomposition behavior of PP and form a char layer on the surface of the composites, consequently resulting in efficient reduction of the flammability parameters, such as heat release rate (HRR), total heat release (THR), smoke production rate (SPR), total smoke production (TSP), and mass loss (ML). © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of charring agent THEIC on flame retardant properties of polypropylene

Tris(2‐hydroxyethyl) isocyanurate (THEIC) was used as charring agent and combined with ammonium polyphosphate (APP) to form an intumescent flame retardant (IFR) for polypropylene (PP). The flame retardancy and combustion performance of PP/IFR composite was tested by limiting oxygen index (LOI), UL‐94 vertical burning test and cone calorimeter. The results showed that PP/IFR composite had highest LOI of 34.8 and obtained V‐0 rating when 30 wt % IFR was loaded and mass ratio APP/THEIC was 2 : 1. The peak heat release (PHRR) and total heat release (THR) values of PP composite containing FRs were remarkably reduced compared with that of pure PP. However, water resistant test demonstrated the PP/IFR composite had poor flame retardant durability, both the LOI value and UL‐94 V‐rating decreased when PP/IFR composite was soaked in water at 70°C after 36 h. The degradation process and the char morphology of IFR and PP/IFR composite were investigated by TGA and SEM images. The possible reaction path between APP and THEIC in the swollen process was proposed. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41214.     

Polyamide‐enhanced flame retardancy of ammonium polyphosphate on epoxy resin

An attractive intumescent flame retardant epoxy system was prepared from epoxy resin (diglycidyl ether of bisphenol A), low molecular weight polyamide (cure agent, LWPA), and ammonium polyphosphate (APP). The cured epoxy resin was served as carbonization agent as well as blowing agent itself in the intumescent flame retardant formulation. Flammability and thermal stability of the cured epoxy resins with different contents of APP and LWPA were investigated by limited oxygen index (LOI), UL‐94 test, and thermogravimetric analysis (TGA). The results of LOI and UL‐94 indicate that APP can improve the flame retardancy of LWPA‐cured epoxy resins. Only 5 wt % of APP can increase the LOI value of epoxy resins from 19.6 to 27.1, and improve the UL‐94 ratings, reaching V‐0 rating from no rating when the mass ratio of epoxy resin to LWPA is 100/40. It is much interesting that LOI values of flame retardant cured epoxy resins (FR‐CEP) increase with decreasing LWPA. The results of TGA, FTIR, and X‐ray photoelectron spectroscopy (XPS) indicate that the process of thermal degradation of FR‐CEP consists of two main stages: the first stage is that a phosphorus rich char is formed on the surface of the material under 500°C, and then a compact char yields over 500°C; the second stage is that the char residue layer can give more effective protection for the materials than the char formed at the first stage do. The flame retardant mechanism also has been discussed according to the results of TGA, FTIR, and XPS for FR‐CEP. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Influence of polyamide 6 as a charring agent on the flame retardancy,thermal, and mechanical properties of polypropylene composites

In this work, polyamide 6 (PA6) as a charring agent has been used in combination with thermoplastic polyurethane (TPU)‐microencapsulated ammonium polyphosphate (MTAPP) forming intumescent flame retardants (IFRs) which applies in polypropylene (PP). The effects of the IFRs on the flame retardancy, morphology of char layers, water resistance, thermal properties and mechanical properties of flame‐retardant PP composites are investigated by limiting oxygen index (LOI), UL‐94 test, scanning electron microscopy (SEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and mechanical properties test. The results show that the PP/MTAPP/PA6 composites exhibit much better flame‐retardant performances than the PP/MTAPP composites. The higher LOI values and UL‐94 V‐2 of the PP/MTAPP composites with suitable amount of PA6 are obtained, which is attributed to the thick and compact char layer structure evidenced by SEM. The results from TGA and DSC demonstrate that the introduction of PA6 into PP/MTAPP composites has a great effect on the thermal stability and crystallization behaviors of the composites. Furthermore, the mechanical properties of PP/MTAPP/PA6 composites are also improved greatly due to the presence of PA6 as a charring agent. POLYM. ENG. SCI., 55:1355–1360, 2015. © 2015 Society of Plastics Engineers     

The intumescent flame‐retardant biocomposites of poly(lactic acid) containing surface‐coated ammonium polyphosphate and distiller's dried grains with solubles (DDGS)

This work aims to develop the poly(lactic acid) (PLA) biocomposites with high flame‐retardant performance, which can be applied in electronic and electrical devices as well as automotive parts. First, an intumescent flame retardant composed of ammonium polyphosphate (APP) as the acid source and the blowing agent, and the distiller's dried grains with solubles (DDGS) as the natural charring agent was designed. The surfaces of DDGS and APP were coated by degradable polymeric flame‐retardant resorcinol di(phenyl phosphate) (RDP), and the coating effects were analyzed. And then the flame‐retardant biocomposites of PLA with RDP‐coated DDGS (C‐DDGS) and RDP‐coated APP (C‐APP) were prepared. The limited oxygen index value of the biocomposites with loading of 15 wt% C‐DDGS and 15 wt% C‐APP reached 32.0%, and UL‐94 V‐0 was attained. The biocomposites also had good mechanical properties and the tensile strength of this sample reached about 57 MPa. Finally, the char residues after burning were analyzed and the flame‐retardant mechanism was discussed.     

Synthesis,thermal degradation,and flame retardance of novel triazine ring‐containing macromolecules for intumescent flame retardant polypropylene

Two novel triazine ring‐containing macromolecules, designated as charring‐foaming agent 1 (CFA1) and charring‐foaming agent 2 (CFA2), were synthesized by a series of polycondensation reactions. Their chemical structures were analyzed by Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (¹³C solid‐state NMR), and elemental analysis, and their thermal degradation properties were assessed by thermogravimetric analysis (TGA). TGA data revealed that CFA1 and CFA2 show high thermal stability and have a high propensity for char formation, their initial decomposition temperatures being 300.2°C and 287.1°C, and their char residues at 800°C amounting to 32.2 wt % and 21.1 wt %, respectively. CFA1 presents higher thermal stability and more char residue than CFA2. Based on experimental results of the flame retardancy (limiting oxygen indices values and UL‐94 V‐0 rating) and the TG data of new intumescent flame retardant polypropylene (IFR‐PP) containing CFA1 and CFA2, CFA1 exhibits more outstanding intumescent flame retardance than CFA2. IFRs containing CFA1 and CFA2 enhanced Notched Izod Impact strength of IFR‐PP, and slightly lower tensile strength of IFR‐PP. IFR2 shows more advantageous effect on mechanical properties of IFR‐PP than IFR1. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

A novel intumescent flame‐retardant system for flame‐retarded LLDPE/EVA composites

A new intumescent flame retardant (IFR) system consisting of ammonium polyphosphate (APP) and charing‐foaming agent (CFA) and a little organic montmorillonite (OMMT) was used in low‐density polyethylene (LLDPE)/ethylene‐vinyl acetate (EVA) composite. According to limiting oxygen index (LOI) value and UL‐94 rating obtained from this work, the reasonable mass ratio of APP to CFA was 3 : 1, and OMMT could obviously enhance the flame retardancy of the composites. Cone calorimeter (CONE) and thermogravimetric analysis (TGA) were applied to evaluate the burning behavior and thermal stability of IFR‐LLDPE/EVA (LLDPE/EVA) composites. The results of cone calorimeter showed that heat release rate peak (HRR‐peak) and smoke production rate peak (SPR‐peak) and time to ignition (TTI) of IFR‐LLDPE/EVA composites decreased clearly compared with the pure blend. TGA data showed that IFR could enhance the thermal stability of the composites at high temperature and effectively increase the char residue. The morphological structures of the composites observed by scanning electron microscopy (SEM) and X‐ray diffraction (XRD) demonstrated that OMMT could well disperse in the composites without exfoliation, and obviously improve the compatibility of components of IFR in LLDPE/EVA blend. The morphological structures of char layer obtained from Cone indicated that OMMT make the char layer structure be more homogenous and more stable. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

三嗪类成炭剂的制备及其阻燃聚丙烯的研究

以三聚氯氰和4,4’-二氨基二苯醚（ODA）为原料制备了具有三嗪环与苯环交替结构主链的新型三嗪类成炭剂(CA-ODA),并将其与聚磷酸铵（APP）复配,用于阻燃聚丙烯（PP）。采用热失重分析方法和锥形量热仪研究了不同质量配比的APP/CA-ODA阻燃体系对PP热稳定性和阻燃性能的影响。结果表明,CA-ODA自身具有良好的热稳定性和成炭性能,三嗪环和苯环交替结构能够促进PP成炭,从而有效地提高了PP的阻燃性能。当APP/CA-ODA体系总添加量为25%,二者质量配比为2:1时,PP复合材料的热释放速率峰值由1046 kW?m-2降低至334 kW?m-2,并且残炭量高达41.5 %。     

多羟基结构三嗪成炭剂在膨胀阻燃PP中的应用

以二乙醇胺为侧链,三聚氯氰和哌嗪为主链,采用一锅法制备了一种多羟基三嗪成炭剂(CDP),将其与聚磷酸铵(APP)复配成膨胀阻燃剂(IFR)用于阻燃聚丙烯(PP)。采用垂直燃烧、极限氧指数、热失重分析等手段研究了阻燃PP的阻燃性能和热稳定性,并用扫描电子显微镜(SEM)对炭层形貌进行了研究。结果表明,APP和CDP具有良好的协同阻燃效果,当APP与CDP质量比为2∶1时,协同阻燃效果最优,仅添加20% IFR,即可使PP达到UL94 V–0级别,LOI为29.5%。热失重分析表明该复合材料在800℃具有最高的残炭量,SEM也显示形成了连续致密的炭层。     

Percolation and catalysis effect of bamboo‐based active carbon on the thermal and flame retardancy properties of ethylene vinyl‐acetate rubber

The effect of percolation and catalysis of bamboo‐based active carbon (BAC) on the thermal degradation and flame retardancy of ethylene vinyl‐acetate rubber (EVM) composites with intumescent flame retardants (IFR) consisting of ammonium polyphosphate (APP) and dipentaerythritol (DPER) has been investigated. The vulcanization characteristics were analyzed by a moving die rheometer. Thermogravimetric analysis (TGA) and fire behavior tests such as limiting oxygen index (LOI), vertical burning (UL 94), and cone calorimetry were used to evaluate the thermal properties and flame retardancy of EVM composites. Scanning electron microscopy (SEM) was used to study the morphology of residues of EVM composites. The addition of BAC significantly increased the maximum torque (M_H) of EVM composites and EVM matrices. The combination of IFR with BAC can improve the thermal stability of EVM composites. Moreover, BAC can enhance char residue and promote the formation of a network for IFR. The current EVM/37IFR/3BAC composite achieved an LOI of 33.6% and a UL 94 V‐0 rating. The PHRR, total heat release (THR), and total smoke release (TSR) for EVM/IFR/BAC were greatly reduced as compared to EVM/40IFR. Also, the mechanical properties of the EVMIFR/BAC composites increased with increasing BAC contents. The physical percolation effect between BAC and EVM before and after thermal degradation, and the chemical catalysis effect between BAC and IFR during thermal degradation are responsible for the improved flame retardancy of EVM composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42414.     

Flammability characteristics and performance of halogen‐free flame‐retarded polyoxymethylene based on phosphorus–nitrogen synergistic effects

The flammability characteristics and thermal stability of a novel halogen‐free flame‐retardant compounding system based on polyoxymethylene (POM) were studied, and a very effective flame retarding formulation for POM was developed from a combination of ammonium polyphosphate (APP), melamine cyanurate (MC), novolak, and dipentaerythritol. The decomposition behavior of POM compounds was evaluated by thermogravimetric analysis. The compound shows optimal flame retardancy with a limiting oxygen index of 52.8 and flammability rating of UL94 V‐0, when 27 wt % APP, 9 wt % MC, 4 wt % novolak, and 4 wt % dipentaerythritol are simultaneously incorporated into POM. The presence of novolak and dipentaerythritol as char‐forming agents results in a dense and compact multicellular char residue for the test bar after combustion, while Fourier transform infrared spectra confirm a characteristic phosphorous‐ and carbon‐rich char resulting from the APP/MC formulation. The pyrolysis–gas chromatography/mass spectrometry analysis indicates that highly flammable formaldehyde gas, the main pyrolysis product of POM, is annihilated by amide derivatives produced by the pyrolysis of MC, imparting better flame retardancy. The comprehensive flame‐retardant mechanisms based on phosphorus–nitrogen synergism promote the high flame retardancy of POM to reach the nonflammability of V‐0 rating. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010