Synthesis and characterization of a novel fluorene‐alt‐carbazole polymer to host green,blue, and red phosphorescence

A novel fluorene‐alt‐carbazole polymer host Poly(9,9‐dioctyl‐9H‐fluorene‐2,7‐diyl‐alt‐N‐tetrahydropyran‐3,6‐carbazole) (PFCz), composed of N‐tetrahydropyran‐3,6‐carbazole and 9,9‐dioctyl‐2,7‐fluorene in the polymer backbone, was synthesized by Suzuki coupling. The PFCz possesses good thermal stability and proper lowest unoccupied molecular orbital (LUMO)/highest occupied molecular orbital (HOMO) energy levels to facilitate the injection and transport of electrons and holes. Upon doping with blue, green, and red phosphors, red ‐ green ‐ blue (R‐G‐B) phosphorescent devices hosted by PFCz have been fabricated and investigated. In contrast to those of blue and green devices, the red devices give better performances with a maximum luminous efficiency of 4.88 cd/A and a maximum power efficiency of 1.85% at 149.84 cd/m², due to favorable triplet energy level (E_T) of PFCz for red phosphor, bis(2‐methyldibenzo[f,h]quinoxaline)(acetylacetonate)iridium(III) [Ir(MDQ)₂(acac)]. Additionally, with different doped concentrations of Ir(MDQ)₂(acac), the PFCz‐related red devices emit nearly pure red light with Commission Internationale de L'Eclairage (CIE) coordinates of (0.57, 0.38), (0.60, 0.38), (0.61, 0.38), and (0.62, 0.38), which were very close to the standard red (0.66, 0.34) by the National Television System Committee. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43234.     

High‐performance copoly(benzimidazole‐benzoxazole‐imide) fibers: Fabrication,structure, and properties

Novel high‐performance copolyimide (co‐PI) fibers containing benzimidazole and benzoxazole ring in the main chain were prepared by a two‐step spinning via the poly(amic acid)s. Effects of the incorporated benzimidazole and benzoxazole units on the micro‐structure and properties of co‐PI fibers were investigated. Fourier transform infrared (FTIR) results indicated that hydrogen bonding is formed in the co‐PI fibers. The co‐PI fibers exhibited discernible crystallization peaks at 14°～15° and 23°～26° (2θ), showing crystalline‐like structure. Moreover, the packing type of benzimidazole‐imide units determined the macromolecules packing of co‐PIs. It was amazedly found that the co‐PI fibers exhibited higher tensile strength and initial modulus than those of corresponding homo‐PI fibers, reaching tensile strength of 2.2–2.6 GPa, initial modulus of 99.1–113.2 GPa. The results of dynamic mechanical analysis (DMA) indicated co‐PI2 fiber had a positive T_g deviation due to the presence of strong intermolecular hydrogen bonding between benzimidazole‐imide and benzoxazole‐imide units, which maybe lead to the effective stress transfer between benzimidazole‐imide units and benzoxazole‐imide units. In addition, the obtained PI fibers exhibited excellent thermal properties with the 10% weight loss temperatures under N₂ in the range of 574–585°C. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42001.     

Design and synthesis of zero–zero‐birefringence polymers using N‐methylmaleimide

Zero–zero‐birefringence polymers which exhibit no orientational birefringence and no photoelastic birefringence may be suitable candidates for the components of optical devices. To develop zero–zero‐birefringence polymers, a novel copolymerization system is required. We investigated two types of birefringence of poly(N‐methylmaleimide) (PMeMI) and showed that PMeMI exhibits positive orientational and photoelastic birefringence. On the basis of the results, we calculated the optimal composition for compensating both types of birefringence by solving three equations which describe the relationship between birefringence properties and weight fraction of monomers. When the copolymer compositions were MMA/BzMA/MeMI = 86/8/6 and 88/8/4 (wt %), zero–zero‐birefringence polymers were obtained. By using MeMI as a comonomer, these zero–zero‐birefringence polymers have a much higher glass transition temperature (T_g) than those of previous researches. Also, this polymer film has high transparency comparable with that of PMMA film. Therefore, we conclude that we successfully prepared zero–zero‐birefringence polymers using N‐substituted maleimide and that N‐substituted maleimide is a promising material for zero–zero‐birefringence polymers for optical devices. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40423.     

Characterization of light‐cured,dental‐resin‐based biocomposites

The dependence of the depth of cure (DOC) and degree of conversion (DC) on the depth of experimental and commercial materials were determined according to ISO 4049 procedure and with the use of Raman spectroscopy, respectively. Moreover, an attempt was made to find the correlation between the DOC and DC and the depth of the material. The hypothesis was that curing time recommended by the manufacturers is appropriate for curing both commercial and experimental materials to achieve comparable values of the examined properties. The impact of the filler characteristic was clearly observed. The longer curing time provides a deeper curing (DOC values) and higher reaction rate (DC); however, the dependence between the DC values and DOC values was not visible. Instead, a logarithmic trend in the relation of the DOC and curing time was clearly observed. The results of this study suggest that the experimental materials give some hope for potential clinical applications and should be further investigated. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42812.     

Preparation,characterization, and flocculation performance of P(acrylamide‐co‐diallyldimethylammonium chloride) by UV‐initiated template polymerization

This study prepared TPDA, a high‐intrinsic‐viscosity cationic polyacrylamide, through ultraviolet (UV)‐initiated template polymerization. Acrylamide (AM) and diallyldimethylammonium chloride (DMD) served as monomers, and poly sodium polyacrylate (PAAS) served as the template. The structure of TPDA was characterized by Fourier‐transform infrared spectroscopy, proton nuclear magnetic resonance spectroscopy, and thermogravimetric analysis. The synthetic conditions of TPDA were studied and optimized by single‐factor experiments. An optimized product was obtained at an intrinsic viscosity of 11.3 dL g^?1 and a conversion rate of 97.2% with a total monomer concentration of 20%, DMD concentration of 30%, initiator concentration of 0.045%, pH of 8, EDTA concentration of 0.3%, and UV irradiation of 90 min. Results showed that TPDA was the copolymer of AM and DMD with a micro‐block structure at the molecular chain. Given its high intrinsic viscosity and cationic block structure, TPDA performed better in kaolin flocculation than that prepared without template addition. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41747.     

Characteristics of diether‐ and phthalate‐based Ziegler‐Natta catalysts for copolymerization of propylene and ethylene and terpolymerization of propylene,ethylene, and 1‐butene

Copolymerization of propylene and ethylene and terpolymerization of propylene, ethylene, and 1‐butene were carried out to compare the characteristics of diether‐ and phthalate‐based Ziegler‐Natta catalysts in a reaction system of pilot scale. The ethylene incorporation with the diether‐based catalyst was higher but the 1‐butene incorporation was lower compared with those of the phthalate‐based catalyst. In the case of copolymers from the diether‐based catalyst, melting behavior, determined through differential scanning calorimetry (DSC), showed a distinct shoulder peak and lots of nuclei were formed during crystallization. The diether‐based catalyst led to polymers having blockier ethylene sequences compared with those of the phthalate‐based catalyst; the highly crystallizable fraction (HIS) containing blockier ethylene sequences was produced with the diether‐based catalyst. These results seem to be the result of regio‐irregular characteristics of the diether‐based catalyst. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 851‐859, 2013     

Novel propargylether‐terminated monomers containing pyridine and phenyl pendent group: Synthesis,cure, and properties

Two novel propargylether‐terminated resins containing pyridine and bulky phenyl pendent group were prepared from propargyl bromide and different diphenols, and highly thermal stable polymers were obtained by the thermal cure of the monomers. The chemical structures of these novel monomers were well confirmed by FTIR, ¹H‐NMR and elemental analysis. Curing and thermal behavior of the resins were investigated using differential scanning calorimetry (DSC) and dynamic thermogravimetry in argon atmosphere. DSC curves of these two monomers showed a single endothermic peak corresponding to the conformation of chromene ring and homopolymerization of the chromene ring. The temperature at 5% weight loss (T_d5) was higher than 440°C under argon and the highest glass transition temperature (T_g) reached 362°C. The rheological behavior and solubility of the monomer were also investigated. The monomers showed excellent flow‐ability, broad processing window, and great solubility. These results showed that the two resins could be ideal candidates for high‐temperature resistant resins. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40469.     

A carbazole–triphenylamine copolymer‐bearing pendant europium complexes: Synthesis and luminescence properties

A novel carbazole–triphenylamine copolymer‐bearing pendant bipyridine PM1TPA and corresponding europium (III) complexed polymer PM1TPA–Eu–x, in which the values of x are 0.1, 0.5, and 1.0 representing the molar ratio of bipyridine ligands complexed with Eu(III), were designed and synthesized. Their chemical structures were confirmed by ¹H NMR, FT‐IR, and elemental analysis. Both PM1TPA and PM1TPA–Eu shows good solubility in common organic solvents such as tetrahydrofuran (THF) and CHCl₃. The 5% weight loss temperature (T_d^5%) of PM1TPA and PM1TPA–Eu–1.0 are 363^oC and 306^oC, respectively. The photoluminescence (PL) spectra of PM1TPA–Eu in solution consists of two emission bands, one in the 400–570 nm region and another at 612 nm, corresponding to the emission of polymer main chain and europium complexes, respectively. When the concentration of PM1TPA–Eu–1.0 in THF solution increases, the PL intensity in the 400–570 nm regions became more and more weaker. And only the characteristic emission of europium complex was observed in the solid film, which indicates that the excited energy absorbed by the polymer backbone was efficiently transferred to the europium complexes. Furthermore, nearly monochromatic red electroluminescence from europium complex was observed from the polymeric light‐emitting diode using PM1TPA–Eu–1.0 as the emissive layer under 25 V forward bias. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42746.     

Acidochromicity of a low‐molecular‐weight pyrimidine‐based copolymer

A new type of low‐molecular‐weight polypyrimidine in a π‐conjugated main chain was prepared by a Grignard reaction between 2‐amino‐4,6‐dichloropyrimidine and 1,4‐dibromo‐2,5‐didodecyloxybenzene in the presence of [1,2‐Bis(diphenylphosphino) ethane]dichloronickel(II). The structure of the copolymer was fully elucidated by Fourier transform infrared spectroscopy, ¹H‐NMR, and elemental analysis. The copolymer had good solubility in common organic solvents. The copolymer displayed a bathochromic shift when protonated with an organic or inorganic acid in chloroform or tetrahydrofuran. The copolymer depicted facile p‐doping and good electron‐transporting electrochemical properties in a 1M H₂SO₄ aqueous solution. The copolymer showed a narrow polydispersity of 1.04. Thermogravimetric analysis showed that the copolymer had a certain thermal stability with no decomposition at a temperature of 250°C under N₂. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41174.     

Role of acrylic acid in the synthesis of core‐shell fluorine‐containing polyacrylate latex with spherical and plum blossom‐like morphology

The core‐shell fluorine‐containing polyacrylate latex was successfully synthesized by two‐stage semicontinuous emulsion copolymerization of methyl methacrylate (MMA), butylacrylate (BA), acrylic acid (AA), and dodecafluoroheptyl methacrylate (DFMA). The fluorine‐containing polyacrylate latex was characterized by Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), dynamic light scattering (DLS), zeta potential, thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC). The effects of AA content on monomer conversion, polymerization stability, particle size, corsslinking degree, carboxyl groups distributions (latex surface, aqueous phase or buried in latex), as well as mechanical properties and water absorption rate of latex film were investigated. The obtained fluorine‐containing polyacrylate latex exhibited core‐shell structure with a particle size of 120–150 nm. The introduction of AA was beneficial for the increase of monomer conversion and the polymerization stability, and had little effects on the mechanical property of latex film. However, the hydrophilicity of AA made the water resistance of latex film get bad. With the increase of AA content, the carboxyl groups preferred to distribute on aqueous phase, and the possibility of homogeneous nucleation increased and more oligomers particles were formed. Moreover, the oligomers would distribute to the latex and continued to grow up, making the latex morphology changed from spherical to plum blossom‐like. The core‐shell latex had two T_g corresponding to the rubber polyacrylate core and hard fluorine‐containing polyacrylate shell, and the latex film possessed excellent thermal stability. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42527.     

Dielectric property,electric breakdown,and discharged energy density of a poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) copolymer with low temperature processing

Different thermal processing methods were used to fabricate the crystalline properties of poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) [P(VDF‐co‐CTFE)] films. We observed that the crystallinity and crystal grain size of the various samples decreased with the quenching temperature. Compared to that of the annealed P(VDF‐co‐CTFE) sample, a higher dielectric constant of 13.9 at a frequency of 100 Hz was obtained in the film with liquid nitrogen quenching because the increasing small crystalline regions were susceptible to the excitation of external electric field. Meanwhile, the breakdown electric strength of the low‐temperature‐quenched film increased to 530 MV/m when the depth of shallow electronic energy level decreased, as depicted by Fröhlich collective electron approximated electric breakdown theory. Moreover, when we introduced the leakage current density curves, the effect of the space charges on the electric displacement was proven. As a result, the discharged energy density of the liquid‐nitrogen‐quenched P(VDF‐co‐CTFE) film was enhanced to 15.32 J/cm³ at an electric field of 530 MV/m; this provided an effective way in addition to chemical modification to achieve a high energy storage ability in this poly(vinylidene fluoride)‐based fluoropolymer. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42794.     

Synthesis,characterization, and properties of acrylate‐modified tung‐oil waterborne insulation varnish

An acrylate‐modified tung‐oil waterborne insulation varnish was synthesized from tung oil, maleic anhydride, and acrylates via a Diels–Alder reaction and free‐radical polymerization, and the varnish could be solidified at a relatively low temperature with blocked hexamethylene diisocyanate as a curing agent. The resulting films were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. The insulation properties (electrical insulation strength, volume resistivity, and surface resistivity) of the varnish films were tested, and the resistances of films to salted water were evaluated. With an increase in the maleic anhydride content, the thermal stability of the film was improved, whereas the electrical insulation strength, volume resistivity, and surface resistivity decreased. The electrical insulation strength of the film after it was immersed in the NaCl solution was lower than that in dry state, and it decreased as the immersed time was prolonged. In particular, the electrical insulation strength loss of the film increased significantly at maleic anhydride contents beyond 25 wt %. Furthermore, the hardness of the film increased with increasing methyl methacrylate/N‐butyl acrylate ratio, whereas the flexibility and adhesion of film decreased to a certain degree at the same time. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41608.     

Elemental sulfur‐based polymeric materials: Synthesis and characterization

New elemental sulfur‐based polymeric materials called poly(sulfur‐random‐divinylbenzene) [poly(S‐r‐DVB)] were synthesized by ring opening polymerization via inverse vulcanization technique in the presence of a mixture of o‐, m‐, and p‐diviniylbenzene (DVB) as a cross‐linker. A clear yellow/orange colored liquid was obtained from the elemental sulfur melted at 160 °C and then by adding various amounts of DVB to this liquid directly via a syringe at 200 °C viscous reddish brown polymeric materials were obtained. The copolymers are soluble in common solvents like tetrahydrofuran, dichloromethane, and chloroform, and they can be coated on any surface as a thin film by a spray coating technique. The characterization of the materials was performed by using nuclear magnetic resonance, fourier transform infrared, and Raman spectroscopies. The morphological properties were monitored via scanning electron microscope technique. Thermal analysis showed that an increase in the amount of DVB in the copolymers resulted in an increase in the thermal decomposition temperature. On the other hand, poly(S‐r‐DVB) copolymers exhibited good percent transmittance as 50% T between 1500 and 13,000 nm in electromagnetic radiation spectrum, which makes them good candidates to be amenable use in military and surveillance cameras. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43655.     

In‐process thermochemical analysis of in situ poly(ethylene glycol methacrylate‐co‐glycidyl methacrylate) monolithic adsorbent synthesis

Thermomolecular mechanisms associated with the synthesis of polymethacrylate monoliths are critical in controlling the physicochemical and binding characteristics of the adsorbent. Notwithstanding, there has been limited reported work on probing the underlining synthesis mechanism essential in establishing the relationship between in‐process polymerization characteristics and the physicochemical properties of the monolith for tailored applications. In this article, we present a real‐time thermochemical analysis of polymethacrylate monolith synthesis by free‐radical polymerization to probe the effects on the physicochemical characteristics of the adsorbent. The experimental results show that an increase in the crosslinker monomer concentration from 30 to 70% resulted in a peak temperature increase from 96.3 to 114.3 °C. Also, an increase in the initiator (benzoyl peroxide) concentration from 1 to 3% w/v resulted in a temperature increase from 90.7 to 106.3 °C. A temperature buildup increases the kinetic rate of intermolecular collision associated with microglobular formation and interglobular interactions. This reduces the structural homogeneity and macroporosity of the polymer matrix. A two‐phase reactive crystallization model was used to characterize the rate of monomeric reaction after initiation and microglobular formation from the liquid monomeric phase to formulate the theoretical framework essential for evaluating the kinetics of the polymer formation process. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43507.     

Effects of hydrosilyl monomers on the performance of polysiloxane encapsulant/phosphor blend based hybrid white‐light‐emitting diodes

Polysiloxane‐based encapsulants were prepared by a hydrosilylation reaction of methacryl polyhedral oligomeric silsesquioxane and different hydrosilyl monomers. With the wavelength conversion method, white‐light‐emitting diodes (WLEDs) were produced by the application of a thermally cured polysiloxane encapsulant/phosphor composite as a wavelength converter on blue‐light‐emitting InGaN diodes. The color rendering index, the Commission Internationale de l'Éclairage coordinates, correlated the color temperature, and the luminous efficacy of the WLEDs with different encapsulants were evaluated. The effects of the chemical structures of hydrosilyl monomers on the optical, mechanical, and thermal resistance properties of the encapsulants, together with the performance of the WLEDs, were investigated. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44524.     

Preparation and properties of epoxy‐modified tung oil waterborne insulation varnish

This work aimed to develop a novel epoxy‐modified tung oil waterborne insulation varnish with blocked hexamethylene diisocyanate as a curing agent. The Diels–Alder reaction between tung oil and maleic anhydride, and the ring‐opening esterification reaction of epoxy resin were confirmed. The conversion rate of epoxy was explored as a function of reaction time and temperature. The effects of epoxy resin content on the thermal stability, water absorption and insulation properties (insulation strength, volume resistivity, and surface resistivity) of films were investigated, and the resistances of films to salted water were evaluated. The increase in epoxy resin contents could improve the thermal stability and insulation properties of films, and decreased the water adsorption of films, but when the epoxy resin content reached 30% and above, the water solubility of resin became poor. After being immersed in 3.5 wt % NaCl solution, the electrical insulation strength of films were lower than that in dry state, and decreased as the immersed time prolonged. In particular, the electrical insulation strength loss of films increased significantly for epoxy resin content at 15% and below. Furthermore, the increase of epoxy resin content could improve the hardness and adhesion of films, but the flexibility of films became worse. On the basis of experimental, the epoxy resin content at 25% was appropriate to prepare waterborne epoxy‐modified tung oil resin. The resulting varnish may have potential as an immersing insulation varnish for the spindle of electric motor. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42755.     

Modification of dry‐spun Suplon polyimide fibers by mixed‐acid oxidation and their effects on the properties of polypropylene‐resin‐based composites

In this study, the effects of mixed‐acid oxidation on the contents of surface elements, morphology, fiber fineness, mechanical properties, mass change rate, chemical structure, and microaggregate structure of dry‐spun Suplon polyimide (PI) fibers were systematically investigated with wet chemical treatment with HNO₃/H₂SO₄. Experiments investigating both the improvement in the O/C ratio of the fiber surface elements and the changes in other performance features were conducted through the functional modification of the fibers. Meanwhile, the causes of specific changes in the mechanical properties of the oxidized PI‐fiber‐reinforced polypropylene‐resin‐based composites were studied and are discussed. The results of this study demonstrate that the treatment of the fibers with HNO₃/H₂SO₄ mixed‐acid oxidation resulted in significant changes in the properties of the fibers; these changes included an uneven surface, increased specific surface area and surface roughness, a locally etched surface, increased surface energy and O/C ratio, an enhanced wettability, an increased fiber fineness, reduced mechanical properties, and a mass gain in the fibers. Although the chemical structures of the fibers treated by oxidized HNO₃/H₂SO₄ were not significantly changed compared to those of the untreated fibers, the microscopic aggregation of the treated fibers changed to some degree, and the ratio of the amorphous regions significantly increased. Taken together, the functional modification of the PI fiber surface was achieved efficiently through the use of a suitable HNO₃/H₂SO₄ oxidation process and with other performance features of the fibers taken into account. This was favorable for the enhancement of the interfacial properties of the polypropylene fibers and the matrix resins, and thus, the modification improved the mechanical properties of the composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44932.     

Aliphatic–aromatic poly(butylene carbonate‐co‐terephthalate) random copolymers: Synthesis,cocrystallization, and composition‐dependent properties

A series of aliphatic–aromatic poly(carbonate‐co‐ester)s poly(butylene carbonate‐co‐terephthalate)s (PBCTs), with weight‐average molecular weight of 113,000 to 146,000 g/mol, were synthesized from dimethyl carbonate, dimethyl terephthalate, and 1,4‐butanediol via a two‐step polycondensation process using tetrabutyl titanate as the catalyst. The PBCTs, being statistically random copolymers, show a single T_g over the entire composition range. The thermal stability of PBCTs strongly depends on the molar composition. Melting temperatures vary from 113 to 213°C for copolymers with butylene terephthalate (BT) unit content higher than 40 mol %. The copolymers have a eutectic melting point when about 10 mol % BT units are included. Crystal lattice structure shifts from the poly(butylene carbonate) to the poly(butylene terephthalate) type crystal phase with increasing BT unit content. DSC and WAXD results indicate that the PBCT copolymers show isodimorphic cocrystallization. The tensile modulus and strength decrease first and then increase according to copolymer composition. The enzymatic degradation of the PBCT copolymers was also studied. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41952.     

Preparation and properties of a polyether‐based polycarboxylate as an antiscalant for gypsum

A polyether‐based copolymer of acrylic acid‐allylpolyethoxy maleic carboxylate (AA‐APEY) was prepared by copolymerization of allylpolyethoxy carboxylate (APEY) and acrylic acid (AA) at different mole ratios. The main aim of this work was to investigate the influence of AA‐to‐APEY mole ratios on the copolymer properties and scale inhibition performance for gypsum. The synthesized copolymer was characterized by Fourier‐transform infrared (FT‐IR) and further conformed by ¹H NMR. The effect of AA‐APEY on controlling calcium sulfate deposits was studied through static scale inhibition tests under standard solution conditions. And the result was compared with that of other polycarboxylates, which are similar to AA‐APEY in structure. Scanning electronic microscopy (SEM), transmission electron microscopy (TEM), and X‐ray powder diffraction (XRD) analysis were carried out to study the morphology and structure changes of calcium sulfate crystals in the presence of AA‐APEY. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40193.     

CO2‐switchable polymeric vesicle‐network structure transition induced by a hairpin‐line molecular configuration conversion

A triblock copolymer, containing a polyethylene glycol (PEG) block and two symmetrical poly(2‐(dimethylamino)ethyl methacrylate) (PDM) blocks, was synthesized by using PEG‐based macroinitiator with copper‐mediated living radical polymerization. The conductivity tests showed that the copolymer exhibited switchable responsiveness to CO₂, i.e., a relatively high conductivity of solution can be switched on and off by bubbling and removing of CO₂. According to the nuclear magnetic resonance results, the CO₂‐switchable conductivity variation could be attributed to protonation and deprotonation of tertiary amine groups in PDM blocks. Moreover, at a proper weight concentration 0.5%, the copolymer aqueous solution displayed a CO₂‐switchable viscosity variation. Scanning electron microscopy, cryogenic transmission electron microscopy, and dynamic light scattering characterization jointly demonstrated that the viscosity variation was the result of a CO₂‐switchable vesicle‐network aggregate structure transition. This structure transition can actually be attributed to a hairpin‐line molecular configuration conversion in terms of the reasonable mechanism discussion. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44417.