The morphology and degradation behavior of electrospun poly(3‐hydroxybutyrate)/Magnetite and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/Magnetite composites

Electrospinning of biodegradable poly(3‐hydroxybutyrate) (PHB)/magnetite and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV)/magnetite composites in 2,2,2‐trifluoroethanol (TFE) and chloroform are investigated to develop nonwoven nanofibrous structure. Ultrafine PHB/magnetite fibers are obtained and the resulting fiber diameters are in the range of 690–710 nm and 8.0–8.4 µm for the polymer dissolved in TFE and chloroform. The surface of PHB composites fiber fabricated in chloroform contains porous structures, which are not observed for the sample of PHB composites fiber dissolved in TFE. The fiber diameters for PHBV5/magnetite composites are in the range of 500–540 nm and 2.3–2.5 µm, depending on the use of TFE and chloroform. The average diameters of PHBV5/magnetite composite fibers are smaller than those of PHB/magnetite composites fiber. All electrospun PHB/magnetite and composite fibers are superparamagnetic. The degradation behaviors of PHB/magnetite and PHBV5/magnetite composite fibers were investigated using Caldimonas manganoxidans. For the fabricated composite fibers, it is found that the degradation rate increased with the increasing loading of magnetite nanoparticles. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41070.     

Crystallization,melting behavior,and wettability of poly(ε‐caprolactone) and poly(ε‐caprolactone)/ poly(N‐vinylpyrrolidone) blends

Both wettability and crystallizability control poly(ε‐caprolactone)'s (PCL) further applications as biomaterial. The wettability is an important property that is governed by both chemical composition and surface structure. In this study, we prepared the PCL/poly(N‐vinylpyrrolidone) (PVP) blends via successive in situ polymerization steps aiming for improving the wettability and decreasing crystallizability of PCL. The isothermal crystallization of PCL/PVP at different PVP concentrations was carried out. The equilibrium melting point (T), crystallization rate, and the melting behavior after isothermal crystallization were investigated using differential scanning calorimetry (DSC). The Avrami equation was used to fit the isothermal crystallization. The DSC results showed that PVP had restraining effect on the crystallizability of PCL, and the crystallization rate of PCL decreased clearly with the increase of PVP content in the blends. The X‐ray diffraction analysis (WAXD) results agreed with that. Water absorptivity and contact angle tests showed that the hydrophilic properties were improved with the increasing content of PVP in blends. The coefficient for the water diffusion into PCL/PVP blends showed to be non‐Fickian in character. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Properties of aligned poly(L‐lactic acid) electrospun fibers

Poly(L‐lactic acid) (PLLA)‐aligned fibers with diameters in the nano‐ to micrometer size scale are successfully prepared using the electrospinning technique from two types of solutions, different material parameters and working conditions. The fiber quality is evaluated using scanning electron microscopy (SEM) to judge fiber diameter, diameter uniformity, orientation, and appearance of defects or beads. The smoothest fibers, most uniform in diameter and defect free, were found to be produced from 10% w/v chloroform/dimethylformamide solution using an accelerating voltage from 10–20 kV. Addition of 1.0% multiwalled carbon nanotubes (MWCNT) into the electrospinning solution decreases fiber diameter, improves diameter uniformity, and slightly increases molecular chain alignment. The fibers were cold crystallized at 120°C and compared with their as‐spun counterparts. The influences of the crystalline phase and/or MWCNT addition were examined using fiber shrinkage, temperature‐modulated calorimetry, X‐ray diffraction, and dynamic mechanical analysis. Crystallization increases the glass transition temperature, T_g, slightly, but decreases the overall fiber alignment through shrinkage‐induced buckling of the fibers when heated above T_g. MWCNT addition has little impact on T_g, but significantly increases the orientation of crystallites. MWCNT addition slightly reduces the dynamic modulus, whereas crystallization increases the modulus in both neat‐ and MWCNT‐containing fibers. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41779.     

Biodegradable supramolecular composites of poly(ε‐caprolactone) and low‐molecular‐weight organic gelators

When a homogeneous hot liquid of poly(ε‐caprolactone) (PCL) with (R)‐12‐hydroxystearic acid (HSA) or N‐carbobenzyloxy‐L ‐isoleucylaminooctadecane (CIA) was gradually cooled to room temperature, the mixture became gelatinous material and then solidified to give a PCL/HSA or PCL/CIA composite. The rheological measurements of the mixtures of PCL with HSA and CIA revealed that the organogels are formed at around 70–50°C and 100–73°C during the cooling process, respectively. Furthermore, the formation of supramolecular fibrillar networks was confirmed by the microscopic and differential scanning calorimetric analyses. The tensile moduli of both the composites were improved by the addition of CIA and HSA. Both the composites showed so high biodegradability as PCL. The fibrillar networks of the composites were also regenerated during the repeated cooling process from the isotropic liquid. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of starch predrying on the mechanical properties of starch/poly(ε‐caprolactone) composites

This study describes the effect of predrying sago starch, a tropical starch, on the resultant mechanical properties of starch/poly(ε‐caprolactone) composite materials. Sago starch was dried to less than a 1% moisture level in a vacuum oven and dispersed into a polycaprolactone matrix with an internal mixer at 90°C. The mechanical properties of the composite were studied according to methods of the Association for Standards, Testing, and Measurement, whereas the morphology was monitored with scanning electron microscopy. The properties were compared with a composite obtained with native starch containing 12% moisture. The results indicated that predrying the starch led to a lower property drop rate in the composite as the starch content increased. The elastic modulus, tensile strength, and elongation at break were higher than those obtained when starch was used without predrying. The morphology observed during scanning electron microscopy studies was used to explain the observed trends in the mechanical properties. In this way, a relatively simple and cost‐effective method was devised to increase the starch loading in the polycaprolactone matrix to obtain properties within the useful range of mechanical properties. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 877–884, 2003     

Effect of peroxide crosslinking on thermal and mechanical properties of poly(ε‐caprolactone)

Poly(ε‐caprolactone) (PCL), a saturated polyester, derived from ring‐opening polymerization of ε‐caprolactone, was chemically crosslinked with various amounts of benzoyl peroxide (BPO) by a two‐step method by first evenly dispersing the BPO into the PCL matrix and then crosslinking at elevated temperature. The gel fraction increased with an increase in BPO content. The modified Charlesby–Pinner equation was used to calculate the ratio of chain scission and crosslinking. The results showed that both scission and crosslinking occurred, and that crosslinking predominated over scission. The number‐average molecular weight between the crosslinks determined by the rubber elasticity theory using the hot set test showed a decrease with increasing BPO content. The melting temperature and crystallinity decreased with an increase in BPO content, and the crystallization temperature increased after crosslinking. Dynamic mechanical analysis results showed a decrease in the glass transition temperature as a result of chemical crosslinking of PCL. This was explained by the observed reduction in crystallinity and the increase in free volume due to restrictions in chain packing. Moreover, Young's modulus and elongation at break generally decreased with an increase in BPO content, but the tensile strength first increased with BPO content up to 1.0 wt%, reached a maximum, and then decreased. Copyright © 2007 Society of Chemical Industry     

Structural properties of CrF3‐ and MnCl2‐filled poly(vinyl alcohol) films

Poly(vinyl alcohol) (PVA) films filled with different amounts of CrF₃ and MnCl₂ were prepared by the casting method. Differential scanning calorimetry (DSC) and X‐ray diffraction (XRD) analysis were used to study the changes in the structure properties that occurred because of filling. The changes occurring in the measured parameters with increasing filler contents were interpreted in terms of the structural modification of the PVA matrix. All the studied samples had a main melting temperature due to the main crystalline phase of PVA. The intensity and position of this peak depended on the filling level. However, the samples of CrF₃‐filled PVA films with a filling level greater than or equal to 10 wt % revealed another melting temperature, which indicated the presence of a new crystalline phase in addition to the main crystalline phase. The changes that occurred in the degree of crystallinity of the studied samples were examined. The calculated degree of crystallinity was formulated numerically to be an exponential function of the filling level. The XRD patterns of the studied samples confirmed the DSC results. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1115–1120, 2003     

Characterization of the fracture properties of aragonite‐ and calcite‐filled poly(ε‐caprolactone) by the essential work of fracture method

Biodegradable polymers, blends, and composites are often investigated during tissue engineering studies, but their fracture properties, which are important mechanical engineering characteristics, are often disregarded or wrongly treated. In this study, essential work of fracture tests were performed on calcium carbonate filled poly(ε‐caprolactone), a very ductile polymer, to determine the effects of different filler shapes (calcite spheres and aragonite whiskers), sizes, and contents on the fracture parameters. Increasing the filler content caused stability problems during crack propagation, and this influenced the self‐similarity of the load–displacement response and resulted in the yielding point being missed. Moreover, the yielding‐related essential work of fracture and the energy dissipating during yielding were found to be almost independent of the filler content and thus could be indicators of matrix–filler adhesion. A shape effect of aragonite whiskers appeared during stable crack propagation; the motion of the particles and the friction on their surface slightly increased the dissipated energy quantum and resulted in a more oriented molecular structure. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

High tensile strength fiber of poly[(R)‐3‐hydroxybutyrate‐co‐(R)‐3‐hydroxyhexanoate] processed by two‐step drawing with intermediate annealing

High tensile strength fibers of poly[(R)‐3‐hydroxybutyrate‐co‐(R)‐3‐hydroxyhexanoate] [P(3HB‐co‐3HH)], a type of microbial polyesters, were processed by one‐step and two‐step cold‐drawn method with intermediate annealing. Thermal degradation behaviors were characterized by differential scanning calorimeter and gel permeation chromatography measurements. Thermal analyses were revealed that molecular weights decreased drastically within melting time at a few minute. One‐step cold‐drawn fiber with drawing ratio of 10 showed tensile strength of 281 MPa, while tensile strength of as‐spun fiber was 78 MPa. When two‐step drawing was applied for P(3HB‐co‐3HH) fibers, the tensile strength was led to 420 MPa. Furthermore, the optimization of intermediate annealing condition leads to enhance the tensile strength at 552 MPa of P(3HB‐co‐3HH) fiber. Wide‐angel X‐ray diffraction measurements of these fibers suggest that the fibers with high tensile strength include much amount of the planer‐zigzag conformation (β‐form) as molecular conformation together with 2₁ helix conformation (α‐form). © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41258.     

Preparation and characterization of poly(ϵ‐caprolactone‐co‐p‐dioxanone)–poly(ethylene glycol)–poly(ϵ‐caprolactone‐co‐p‐dioxanone)/bioactive inorganic particle nanocomposites

With an aim to develop injectable hydrogel with improved solution stability and enhanced bone repair function, thermogelling poly(ε‐caprolactone‐co‐p‐dioxanone)‐poly(ethylene glycol)‐poly(ε‐caprolactone–co‐p‐dioxanone) (PECP)/bioactive inorganic particle nanocomposites were successfully prepared by blending the triblock copolymer (PECP) with nano‐hydroxyapatite (n‐HA) or nano‐calcium carbonate (n‐CaCO₃). The hydrogel nanocomposites underwent clear sol–gel transitions with increasing temperature from 0 to 50°C. The obtained hydrogel nanocomposites were investigated by ¹H NMR, FT‐IR, TEM, and DSC. It was found that the incorporation of inorganic nanoparticles into PECP matrix would lead to the critical gelation temperature (CGT) shifting to lower values compared with the pure PECP hydrogel. The CGT of the hydrogel nanocomposites could be effectively controlled by adjusting PECP concentration or the content of inorganic nanoparticles. The SEM results showed that the interconnected porous structures of hydrogel nanocomposites were potentially useful as injectable scaffolds. In addition, due to the relatively low crystallinity of PECP triblock copolymer, the aqueous solutions of the nanocomposites could be stored at low temperature (5°C) without crystallization for several days, which would facilitate the practical applications. The PECP/bioactive inorganic particle hydrogel nanocomposites are expected to be promising injectable tissue engineering materials for bone repair applications. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

The influence of thermal treatment and processing on the structure and morphology of poly(propylene‐ran‐1‐butene) copolymers

New poly(propylene‐ran‐1‐butene) copolymers were analyzed to study the influence of different processing techniques on their structure and morphology. Wide‐angle X‐ray diffraction allowed determination of the percentage of the γ form and the crystallinity in the samples and also the influence of the percentage of 1‐butene on the cell parameters. Furthermore, it was possible to appraise the contributions of different stacks of lamellae to the small‐angle X‐ray diffraction patterns. © 2001 Society of Chemical Industry     

Elaboration and thermal analysis of nanocomposites based on poly(methyl methacrylate‐co‐4‐vinylpyridine) and Maghnia bentonite

Nanocomposites based on an organically modified bentonite, from Maghnia Algeria (OBT) and a copolymer of methyl methacrylate with 4‐vinylpyridine (PMM4VP) synthesized in dioxan at room temperature using a neutral Ni(II)α‐benzoinoxime complex as a single component initiator, were elaborated via solution intercalation method and characterized by several techniques. X‐ray diffraction and transmission electron microscopy investigations indicate that mainly exfoliated and intercalated PMM4VP/OBT nanocomposites were elaborated and that the degree of exfoliation decreases with an increase of the OBT loading. Thermal analyses of these nanocomposites compared with their virgin copolymer confirmed a significant improvement of their thermal stability as evidenced by an increase of 28°C in their onset degradation temperatures. In addition, differential scanning calorimetry displayed an increase in the range of 12–18°C in their glass transition temperatures relative to their virgin copolymer. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Structural properties of CrF3‐ and MnCl2‐filled poly(vinylalcohol) films

Poly(vinylalcohol) (PVA) films filled with different filling levels of CrF₃ and MnCl₂ have been prepared by the casting method. Differential scanning calorimetry (DSC) and X‐ray diffraction (XRD) analysis were used to study the changes in structure properties that occur due to filling. The changes occurring in the measured parameters with increasing the filler content was been interpreted in terms of the structural modification of the PVA matrix. It was found that all studied samples had the main melting temperature due to the main crystalline phase of PVA. The intensity and position of this peak depended on the filling level. On the other hand, the samples of CrF₃‐filled PVA films with filling level W ≥ 10 wt % revealed another melting temperature, indicating the presence of a new crystalline phase besides the main crystalline phase. Changes occurring in the degree of crystallinity of the studied samples were discussed. The calculated degree of crystallinity was formulated numerically to be an exponential function of filling level. The X‐ray diffraction patterns of the studied samples confirmed the DSC results. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 516–521, 2003     

Biodegradable blends of poly(ε‐caprolactone) with α‐chitin and chitosan: specific interactions,thermal properties and crystallization behavior

Films of poly(ε‐caprolactone) (PCL) blends with α‐chitin and chitosan were prepared as completely biodegradable polyester/polysaccharide composites. DSC thermal analysis revealed that the crystallization of PCL was suppressed by blending with α‐chitin and chitosan. The specific interaction between PCL and polysaccharides was investigated by FTIR spectroscopy. The PCL carbonyl vibration bands could be resolved into three components: crystalline, amorphous and interacting. The FTIR spectra indicated that there were hydrogen bonding interactions between PCL and polysaccharides, and that polysaccharides suppressed the crystallization of PCL, consistent with the results obtained by DSC. © 2001 Society of Chemical Industry     

Effects of copolymer microstructure on the properties of electrospun poly(l‐lactide‐co‐ε‐caprolactone) absorbable nerve guide tubes

The main objective of this work has been to study the effects of copolymer microstructure, both chemical and physical, on the microporosity, in vitro hydrolytic degradability and biocompatibility of electrospun poly(l ‐lactide‐co‐ε‐caprolactone), PLC, copolymer tubes for potential use as absorbable nerve guides. PLC copolymers with L : C compositions of 50 : 50 and 67 : 33 mol % were synthesized via the ring‐opening copolymerization of l ‐lactide (L) and ε‐caprolactone (C) at 120°C for 72 h using stannous octoate (tin(II) 2‐ethylhexanoate) and n‐hexanol as the initiating system. Electrospinning was carried out from solution in a dichloromethane/dimethylformamide (7 : 3 v/v) mixed solvent at room temperature. The in vitro hydrolytic degradation of the electrospun PLC tubes was studied in phosphate buffer saline over a period of 36 weeks. The microporous tubes were found to be gradually degradable by a simple hydrolysis mechanism leading to random chain scission. At the end of the degradation period, the % weight retentions of the PLC 50 : 50 and 67 : 33 tubes were 15.6% and 70.2%, respectively. Pore stability during storage as well as cell attachment and proliferation of mouse fibroblast cells (L929) showed the greater potential of the PLC 67 : 33 tubes for use as temporary scaffolds in reconstructive nerve surgery. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4357–4366, 2013     

Effects of supercritical carbon dioxide treatment on the morphology of poly(l‐lactide)

Synthetic l ‐lactide random copolymers can be employed as controlled release materials when prepared using supercritical carbon dioxide (scCO₂), since they are biodegradable via hydrolysis. To determine the effects of thermal properties on polymer performance following scCO₂ processing, three types of poly(l ‐lactide) having different properties were assessed. The T_m of one poly(l ‐lactide) sample (H‐100) was found to be approximately 170 °C over the processing pressure range from 8 to 18 MPa, while a second sample (H‐440) also showed a constant value of approximately 152 °C. In contrast, the poly(l ‐lactide) REVODE exhibited a T_m of 146 °C prior to processing but a higher value of 147 °C following treatment at 8 MPa. Unlike the H‐100 and H‐440, the T_m value of the REVODE tended to decrease with increasing pressure. The T_g values increased greatly under mild conditions of 8 MPa pressure and a temperature of 40 °C. In particular, the T_g values for the H‐440 and REVODE increased by 4 °C and 5 °C, respectively. All T_g values were lowest at 12 MPa and increased with increasing processing pressure, although the effect of processing temperature was minimal. The Χ_{c DSC} of the H‐100 was 18% initially but increased to 20% upon scCO₂ processing at 40 °C and 14 MPa, and showed further increases at higher processing temperatures. Although the relationship between processing temperature and Χ_{c DSC} values for the H‐440 showed the same trend as observed with the H‐100, a different trend was seen for the REVODE. The Χ_{c XRD} values obtained from the XRD analyses differed from the values generated by DSC analysis, and showed a maximum degree of crystallinity following processing at 80 °C both with and without scCO₂ treatment. ATR FT‐IR analyses identified peaks due to semicrystalline regions in poly(l ‐lactide) samples treated with scCO₂, even when applying low temperatures. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44006.     

Characterization of biodegradable polymers by inverse gas chromatography. II. Blends of amylopectin and poly(ε‐caprolactone)

Amylopectin (AP), a potato‐starch‐based polymer with a molecular weight of 6,000,000 g/mol, was blended with poly(ε‐caprolactone) (PCL) and characterized with inverse gas chromatography (IGC), differential scanning calorimetry (DSC), and X‐ray diffraction (XRD). Five different compositions of AP–PCL blends ranging from 0 to 100% AP were studied over a wide range of temperatures (80–260°C). Nineteen solutes (solvents) were injected onto five chromatographic columns containing the AP–PCL blends. These solutes probed the dispersive, dipole–dipole, and hydrogen‐bonding interactions, acid–base characteristics, wettability, and water uptake of the AP–PCL blends. Retention diagrams of these solutes in a temperature range of 80–260°C revealed two zones: crystalline and amorphous. The glass‐transition temperature (T_g) and melting temperature (T_m) of the blends were measured with these zones. The two zones were used to calculate the degree of crystallinity of pure AP and its blends below T_m, which ranged from 85% at 104°C to 0% at T_m. IGC complemented the DSC method for obtaining the T_g and T_m values of the pure AP and AP–PCL blends. These values were unexpectedly elevated for the blends over that of pure AP and ranged from 105 to 152°C for T_g and from 166 to 210°C for T_m. The T_m values agreed well with the XRD analysis data. This elevation in the T_g and T_m values may have been due to the change in the heat capacity at T_g and the dependence of T_g on various variables, including the molecular weight and the blend composition. Polymer blend/solvent interaction parameters were measured with a variety of solutes over a wide range of temperatures and determined the solubility of the blends in the solutes. We were also able to determine the blend compatibility over a wide range of temperatures and weight fractions. The polymer–polymer interaction coefficient and interaction energy parameter agreed well on the partial miscibility of the two polymers. The dispersive component of the surface energy of the AP–PCL blends was measured with alkanes and ranged from 16.09 mJ/m² for pure AP to 38.26 mJ/m² when AP was mixed with PCL in a 50/50% ratio. This revealed an increase in the surface energy of AP when PCL was added. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3076–3089, 2006     

The kinetics of the thermal decomposition of poly(3‐hydroxybutyrate) and maleated poly(3‐hydroxybutyrate)

The thermal decomposition mechanism of maleated poly(3‐hydroxybutyrate) (PHB) was investigated by FTIR and ¹H NMR. The results of experiments showed that the random chain scission of maleated PHB obeyed the six‐membered ring ester decomposition process. The thermal decomposition behavior of PHB and maleated PHB with different graft degree were studied by thermogravimetry (TGA) using various heating‐up rates. The thermal stability of maleated PHB was evidently better than that of PHB. With increase in graft degree, the thermal decomposition temperature of maleated PHB gradually increased and then declined. Activation energy E_a as a kinetic parameter of thermal decomposition was estimated by the Flynn‐Wall‐Ozawa and Kissinger methods, respectively. It could be seen that approximately equal values of activation energy were obtained by both methods. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1789–1796, 2002; DOI 10.1002/app.10463     

Poly(ε‐caprolactone) composite scaffolds loaded with gentamicin‐containing β‐tricalcium phosphate/gelatin microspheres for bone tissue engineering applications

In this study, novel poly(ε‐caprolactone) (PCL) composite scaffolds were prepared for bone tissue engineering applications, where gentamicin‐loaded β‐tricalcium phosphate (β‐TCP)/gelatin microspheres were added to PCL. The effects of the amount of β‐TCP/gelatin microspheres added to the PCL scaffold on various properties, such as the gentamicin release rate, biodegradability, morphology, mechanical strength, and pore size distribution, were investigated. A higher amount of filler caused a reduction in the mechanical properties and an increase in the pore size and led to a faster release of gentamicin. Human osteosarcoma cells (Saos‐2) were seeded on the prepared composite scaffolds, and the viability of cells having alkaline phosphatase (ALP) activity was observed for all of the scaffolds after 3 weeks of incubation. Cell proliferation and differentiation enhanced the mechanical strength of the scaffolds. Promising results were obtained for the development of bone cells on the prepared biocompatible, biodegradable, and antimicrobial composite scaffolds. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40110.