Effect of nano‐SiO2 on granule characteristic and fusion process of Poly(vinyl chloride‐co‐vinyl acetate)/nano‐SiO2 composite resin

Poly(vinyl chloride‐co‐vinyl acetate) (PVVA)/nano‐SiO₂ composite resin was prepared by radical suspension polymerization of the monomers in the presence of fumed nano‐SiO₂ particles premodified with γ‐methylacryloxypropyl trimethoxysilane. The cool dioctyl phthalate absorption percentage, granule porosity, and specific surface area of the composite resin were enhanced through incorporation of nano‐SiO₂ into the PVVA. Scanning electron microscope pictures showed the resin had higher porosity. PVVA/nano‐SiO₂ composite resin was mixed with pure PVC resin to form a mixture sample (polymer‐composite blend [PCB]) and the mixture was fused in the torque rheometer. The rheological test results indicated that, at a certain nano‐SiO₂ content, the fusion speed of PCB was accelerated and the fusion temperature of PCB was decreased, owing to nano‐SiO₂ dispersed evenly in the polymer matrix. When excessive nano‐SiO₂ was loaded, the fusion torque, the fusion time, and the fusion temperature of PCB were all increased. These properties are correlative to the dispersive density of nano‐SiO₂ in the polymer matrix. This study also demonstrated that the introduction of small amounts of nano‐SiO₂ into the resin increased the impact strength and tensile strength of PCB simultaneously. J. VINYL ADDIT. TECHNOL., 20:230–236, 2014. © 2014 Society of Plastics Engineers     

Effects of high nano‐SiO2 contents on properties of epoxy‐modified polybenzoxazine

High‐performance nanosilica composites based on epoxy‐modified polybenzoxazine matrices are developed. Chemorheological study of benzoxazine–epoxy resin mixtures reveals that processing window of the benzoxazine resin (BA‐a) is substantially broadened with an addition of the liquid epoxy. Glass transition temperature (T _g) of the BA‐a copolymerized with epoxy resin shows a synergistic behavior with a maximum T _g value (174°C) at the benzoxazine–epoxy mass ratio of 80:20. The copolymer at this composition is also used as a matrix for nano‐SiO₂ composites. A very low melt viscosity of the benzoxazine–epoxy mixtures promotes good processability with the maximum attainable nano‐SiO₂ loading up to 35 wt%. From scanning electron microscopy investigation, fracture surface of the 35 wt% nano‐SiO₂‐filled benzoxazine–epoxy composite reveals relatively homogeneous distribution of the nano‐SiO₂ in the copolymer with good particle wet‐out. In addition, very high reinforcing effect was also observed in such high content of the nano‐SiO₂, i.e., about 2.5 times in modulus improvement. This improvement is attributed to the strong bonding between the copolymer matrix and the nano‐SiO₂ through ether linkage as confirmed by Fourier‐transform infrared investigation. POLYM. COMPOS., 38:2261–2271, 2017. © 2015 Society of Plastics Engineers     

Thermal and mechanical properties of poly(urethane‐imide)/epoxy/silica hybrids

Improving properties of polyurethane (PU) elastomers have drawn much attention. To extend the properties of the modified PU composite, here a new method via the reaction of poly(urethane‐imide) diacid (PUI) and silane‐modified epoxy resin (diglycidyl ether of bisphenol A) was developed to prepare crosslinked poly (urethane‐ imide)/epoxy/silica (PUI/epoxy/SiO₂) hybrids with enhanced thermal stability. PUI was synthesized from the reaction of trimellitic anhydride with isocyanate‐terminated PU prepolymer, which was prepared from reaction of polytetramethylene ether glycol and 4,4′‐diphenylmethane diisocyanate. Thermal and mechanical properties of the PUI/epoxy/SiO₂ hybrids were investigated to study the effect of incorporating in situ SiO₂ from silane‐modified epoxy resin. All experimental data indicated that the properties of PUI/epoxy/SiO₂ hybrids, such as thermal stability, mechanical properties, were improved due to the existence of epoxy resin and SiO₂. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Comprehensive high‐performance epoxy nanocomposites co‐reinforced by organo‐montmorillonite and nano‐SiO2

Comprehensive high‐performance epoxy nanocomposites were successfully prepared by co‐incorporating organo‐montmorillonite (o‐MMT) and nano‐SiO₂ into epoxy matrix. Because of the strong interaction between nanoscale particles, the MMT layers were highly exfoliated, and the exfoliated nanoscale MMT monoplatelets took an interlacing arrangement with the nano‐SiO₂ particles in the epoxy matrix, as evidenced by X‐ray diffraction measurement and transmission electron microscopy inspection. Mechanical tests and thermal analyses showed that the resulting epoxy/o‐MMT/nano‐SiO₂ nanocomposites improved substantially over pure epoxy and epoxy/o‐MMT nanocomposites in tensile modulus, tensile strength, flexural modulus, flexural strength, notch impact strength, glass transition temperature, and thermal decomposition temperature. This study suggests that co‐incorporating two properly selected nanoscale particles into polymer is one pathway to success in preparing comprehensive high‐performance polymer nanocomposites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and studies of the physical properties of polyaniline and polyurethane‐modified epoxy composites

Two series of toughened, semiconductive polyaniline (PANI)/polyurethane (PU)‐epoxy (PANI/PU‐EPOXY) nano‐composites were prepared using a conductive polymer, PANI, and PU prepolymer‐modified‐diglycidyl ether of bisphenol A (DGEBA) epoxy. First, the PU prepolymer‐modified epoxy oligomer was synthesized by a stoichiometric reaction between the terminal isocyanate groups of the PU prepolymer and the pendent hydroxyl groups of the epoxide. PU prepolymers were made either of polyester (polybutylene adipate, PBA) or polyether (polypropylene glycol, PPG) segments. The composites were characterized by thermal, morphological, mechanical, and electrical studies. Impact strength was enhanced 100% in PU (PPG 2000)‐modified composites; whereas, only ca. 30–50% increases in impact strength were observed for the other modified composites. In addition, the thermal stability of this composite proved superior to that of neat epoxy resin, regardless of a PU content at 27.5 wt%. Scanning electron microscopy (SEM) morphology study showed that the spherical PU (PPG 2000) particles (ca. 0.2–0.5 μm) dispersed within the matrix accounts for these extraordinary properties. The conductivity of the composite increased to ca. 10^?9–10^?3 S cm^?1 upon addition of PANI when tested in the frequency range 1 kHz–13 MHz. This study demonstrated a useful way to simultaneously improve the toughness and conductivity of the epoxy composite, thus rendering it suitable for electromagnetic interference and various charge dissipation applications. POLYM. ENG. SCI., 2008. © 2007 Society of Plastics Engineers     

Enhanced mechanical properties and bactericidal activity of polypropylene nanocomposite with dual‐function silica–silver core‐shell nanoparticles

Dual‐function silica–silver core‐shell (SiO₂@Ag) nanoparticles (NPs) with the core diameter of 17 ± 2 nm and the shell thickness of about 1.5 nm were produced using a green chemistry. The SiO₂@Ag NPs were tested in vitro against gram‐positive Staphylococcus aureus (S. aureus) and gram‐negative Escherichia coli (E. coli), both of which are human pathogens. Minimal inhibitory concentrations of the SiO₂@Ag NPs based on Ag content are 4 and 10 μg mL^?1 against S. aureus and E. coli, respectively. These values are similar to those of Ag NPs. SiO₂@Ag NPs were for the first time incorporated to a commodity polypropylene (PP) polymer. This yielded an advanced multifunctional polymer using current compounding technologies i.e., melt blending by twin‐screw extruder and solvent (toluene) blending. The composite containing 5 wt % SiO₂@Ag NPs (0.05 wt % Ag) exhibited efficient bactericidal activity with over 99.99% reduction in bacterial cell viability and significantly improved the flexural modulus of the PP. Anodic stripping voltammetry, used to investigate the antibacterial mechanism of the composite, indicated that a bactericidal Ag⁺ agent was released from the composite in an aqueous environment. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis,characterization, and mechanical property of poly(urethane‐glycidyl methacrylate‐methyl methacrylate) hybrid polymers

Hybrid particles of polyurethane (PU) containing a number of small poly(methyl methacrylate) (PMMA) nanoparticles inside were prepared using glycidyl methacrylate (GMA) monomer as a linker between PU and PMMA; the resulting polymers were poly (urethane‐glycidyl methacrylate‐methyl methacrylate) (PUGM). It was found that the average particle size (D_p) of the PU particles decreased by the inclusion of PMMA particles possibly owing to the low‐solution viscosity of PU. However, D_p of the PUGM hybrid particles increased with increasing the number of covalent bonds between PMMA and PU, which might be due to decreasing the amount of ionic groups per PU chain. Subsequently, the tensile properties of the films made of the PUGM hybrid particles were investigated. It was observed that the modulus of the PU films increased upon the addition of PMMA particle because of a filler effect. In addition, it was seen that the modulus of PUGM hybrid films increased further with increasing the number of covalent bonds. This was attributed to “restricted mobility” of PU chains anchored to the PMMA particles. It was also observed that the tensile strength changed only slightly for PUGM particles, suggesting that the PU matrix was probably responsible for the necking behavior of the films. The elongation of the samples was found to depend on both the presence of covalent bonds between the PMMA particles and PU matrix and the reduced mobility of the PU chains anchored to PMMA particles. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and evaluation of nano‐epoxy composite resins containing electrospun glass nanofibers

In this study, electrospun glass (structurally amorphous SiO₂) nanofibers (EGNFs) with diameters of ～ 400 nm were incorporated into epoxy resin for reinforcement and/or toughening purposes; the effects of silanization treatment (including different functional groups in silane molecules) and mass fraction of EGNFs on strength, stiffness, and toughness of the resulting nano‐epoxy composite resins were investigated. The experimental results revealed that EGNFs substantially outperformed conventional glass fibers (CGFs, with diameters of ～ 10 μm) in both tension and impact tests, and led to the same trend of improvements in strength, stiffness, and toughness at small mass fractions of 0.5 and 1%. The tensile strength, Young's modulus, work of fracture, and impact strength of the nano‐epoxy composite resins with EGNFs were improved by up to 40, 201, 67, and 363%, respectively. In general, the silanized EGNFs with epoxy end groups (G‐EGNFs) showed a higher degree of toughening effect, while the silanized EGNFs with amine end groups (A‐EGNFs) showed a higher degree of reinforcement effect. The study suggested that electrospun glass nanofibers could be used as reinforcement and/or toughening agent for making innovative nano‐epoxy composite resins, which would be further used for the development of high‐performance polymer composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Nano‐sio2‐reinforced ultraviolet‐curing materials for three‐dimensional printing

As an additive manufacturing technology, ultraviolet (UV)‐curing three‐dimensional printing, which requires the use of a photocurable resin, is increasingly being used to produce customized end‐user parts of many complex shapes. In this study, to improve the strength and ductility of printing materials, nano‐SiO₂‐reinforced photocurable resins were prepared by a planetary ball mill; then, the morphology, photochemistry, thermal property, and mechanical properties of the nanocomposites were investigated and characterized. Transmission electron microscopy analysis indicated that the modified nano‐SiO₂ was well dispersed in the photocurable resin. The glass‐transition temperature increased from 67.2°C for the unfilled resin to 71.7 and 80.1°C for nanocomposites with nano‐SiO₂ contents of 0.3 and 0.7 wt %, respectively. The tensile strength and impact strength were increased by 46.7 and 165.3% for nanocomposites with 0.3 wt % nano‐SiO₂. The flexural modulus of the nanocomposites increased from 1.7 to 8.0 GPa when 0.7 wt % nano‐SiO₂ was added to the photocurable resin; this appeared to originate from the relatively high level of dispersion and the intimate combination of the nano‐SiO₂ with the matrix. The investigation of the physical and chemical properties of such UV‐curing materials showed that the low filler concentration (<1 wt %) of nano‐SiO₂ did not affect the processability of the nanocomposites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42307.     

Synthesis,physical properties,and characterization of starch‐based blend films by adding nano‐sized TiO2/poly(methyl metacrylate‐co‐acrylamide)

The purpose of this study was to improve the physical properties and to expand the application range of starch‐based blend films added nano‐sized TiO₂/poly(methyl methacrylate‐co‐acrylamide) (PMMA‐co‐AM). Starch‐based blend films were prepared by using corn starch, polyvinyl alcohol (PVA), nano‐sized PMMA‐co‐AM, nano‐sized TiO₂/PMMA‐co‐AM particles, and additives, i.e., glycerol (GL) and citric acid (CA). Nano‐sized PMMA‐co‐AM was synthesized by emulsion polymerization and TiO₂ nanoparticles were also prepared by using sol–gel method. Nano‐sized TiO₂/PMMA‐co‐AM particles were synthesized by wet milling for 48 h. The morphology and crystallinity of TiO₂, nano‐sized PMMA‐co‐AM and TiO₂/PMMA‐co‐AM particles were investigated by using the scanning electron microscope (SEM) and X‐ray diffractometer (XRD). In addition, the functional groups of the TiO₂/PMMA‐co‐AM particles were characterized by IR spectrophotometry (FTIR). The physical properties such as tensile strength (TS), elongation at break (%E), degree of swelling (DS), and solubility (S) of starch‐based films were evaluated. It was found that the adding of nano‐sized particles can greatly improve the physical properties of the prepared films. The photocatalytic degradability of starch/PVA/nano‐sized TiO₂/PMMA‐co‐AM composite films was evaluated using methylene blue (MB) and acetaldehyde (ATA) as photodegradation target under UV and visible light. The degree of decomposition (C/C₀) of MB and ATA for the films containing TiO₂ and CA was 0.506 and 0.088 under UV light irradiation and 0.586 (MB) and 0.631 (ATA) under visible light irradiation, respectively. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

New epoxy/silica‐titania hybrid materials prepared by the sol–gel process

A new type of inorganic‐polymer hybrid materials of epoxy/silica‐titania had been prepared by incorporating grafted epoxy, which had been synthesized by epoxy and tetraethoxysilane (TEOS), with highly reactive TEOS and tetrabutyltitanate (TBT) by using the in situ sol–gel process. The grafted epoxy was confirmed by Fourier transform infrared spectroscopy (FT‐IR) and ¹H‐NMR spectroscopic technique. Results of FT‐IR spectroscopy and atomic force microscopy (AFM) demonstrated that epoxy chains have been covalently bonded to the surface of the SiO₂‐TiO₂ particles. The particles size of SiO₂‐TiO₂ are about 20–50 nm, as characterized by AFM. The experimental results showed that the glass‐transition temperatures and the modulus of the modified systems were higher than that of the unmodified system, and the impact strength was enhanced by two to three times compared with that of the neat epoxy. The morphological structure of impact fracture surface and the surface of the hybrid materials were observed by scanning electron microscopy and AFM, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1075–1081, 2006     

Particle morphology and NMR structure of polymethylmethacrylate/polystyrene emulsifier‐free core–shell cationic latices in the presence of DBMEA

In the absence of emulsifier, we prepared stable emulsifier‐free polymethylmethacrylate/polystyrene (PMMA/PSt) copolymer latex by batch method with comonomer N,N‐dimethyl, N‐butyl, N‐methacryloloxylethyl ammonium bromide (DBMEA) by using A1BN as initiator. The size distribution of the latex particles was very narrow and the copolymer particles were spherical and very uniform. Under the same recipe and polymerization conditions, PMMA/PSt and PSt/PMMA composite polymer particle latices were prepared by a semicontinuous emulsifier‐free seeded emulsion polymerization method. The sizes and size distributions of composite latex particles were determined both by quasi‐elastic light scattering and transmission electron microscopy (TEM). The effects of feeding manner and staining agents on the morphologies of the composite particles were studied. The results were as follows: the latex particles were dyed with pH 2.0 phosphotungestic acid solution and with uranyl acetate solution, respectively, revealing that the morphologies of the composite latex particles were obviously core–shell structures. The core–shell polymer structure of PMMA/PSt was also studied by ¹H, ¹³C, 2D NMR, and distortionless enhancement by polarization transfer, or DEPT, spectroscopy. Results showed that PMMA/PSt polymers are composed of PSt homopolymer, PMMA homopolymer, and PMMA‐g‐PSt graft copolymers; results by NMR are consistent with TEM results. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1681–1687, 2005     

Water‐dispersible conducting polyaniline/nano‐SiO2 composites without any stabilizer

A water‐dispersible conducting polyaniline/ nano‐SiO₂ composite, with a conductivity of 0.071 S cm^?1 at 25°C, was prepared by the oxidative polymerization of aniline in the presence of amorphous nano‐SiO₂ particles. And the structure, morphology, thermal stability, conductivity, and electroactivity of this composite were also investigated. This composite has been steadily dispersed in the aqueous solution for about 10–36 h without the need for any stabilizer. It would significantly impulse the commercial applications of conducting polyaniline/nano‐SiO₂ composite as fillers for antistatic and anticorrosion coatings. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis of EP‐POSS mixture and the properties of EP‐POSS/epoxy,SiO2/epoxy,and SiO2/EP‐POSS/epoxy nanocomposite

The hybrid material of EP‐POSS mixture was synthesized by the hydrolysis and condensation of (γ‐glycidoxypropyl) trimethoxysilane. A series of binary systems of EP‐POSS/epoxy blends, epoxy resin modified by silica nanoparticles (SiO₂/epoxy), and ternary system of SiO₂/EP‐POSS/epoxy nanocomposite were prepared. The dispersion of SiO₂ in the matrices was evidenced by transmission electron micrograph, and the mechanical properties, that is, flexural strength, flexural modulus, and impact strength were examined for EP‐POSS/epoxy blends, SiO₂/epoxy, and SiO₂/EP‐POSS/epoxy, respectively. The fractured surface of the impact samples was observed by scanning electron micrograph. Thermogravimetry analysis were applied to investigate the different thermal stabilities of the binary system and ternary system by introducing EP‐POSS and SiO₂ to epoxy resin. The results showed that the impact strength, flexural strength, and modulus of the SiO₂/EP‐POSS/epoxy system increased around by 57.9, 14.1, and 44.0% compared with the pure epoxy resin, T_i, T_max and the residues of the ternary system were 387°C, 426°C, and 25.2%, increased remarkably by 20°C, 11°C and 101.6% in contrast to the pure epoxy resin, which was also higher than the binary systems. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 810‐819, 2013     

Studies of solvent effect on the conductivity of 2‐mercaptopyridine‐doped solid polymer blend electrolytes and its application in dye‐sensitized solar cells

Solvents and electrolytes play an important role in the fabrication of dye‐sensitized solar cells (DSSCs). We have studied the poly(ethylene oxide)‐poly(methyl methacrylate)‐KI‐I₂ (PEO‐PMMA‐KI‐I₂) polymer blend electrolytes prepared with different wt % of the 2‐mercaptopyridine by solution casting method. The polymer electrolyte films were characterized by the FTIR, X‐ray diffraction, electrochemical impedance and dielectric studies. FTIR spectra revealed complex formation between the PEO‐PMMA‐KI‐I₂ and 2‐mercaptopyrindine. Ionic conductivity data revealed that 30% 2‐mercaptopyridine‐doped PEO‐PMMA‐KI‐I₂ electrolyte can show higher conductivity (1.55 × 10^?5 S cm^?1) than the other compositions (20, 40, and 50%). The effect of solvent on the conductivity and dielectric of solid polymer electrolytes was studied for the best composition (30% 2‐mercaptopyridine‐doped PEO‐PMMA‐KI‐I₂) electrolyte using various organic solvents such as acetonitrile, N,N‐dimethylformamide, 2‐butanone, chlorobenzene, dimethylsulfoxide, and isopropanol. We found that ac‐conductivity and dielectric constant are higher for the polymer electrolytes processed from N,N‐dimethylformamide. This observation revealed that the conductivity of the solid polymer electrolytes is dependent on the solvent used for processing and the dielectric constant of the film. The photo‐conversion efficiency of dye‐sensitized solar cells fabricated using the optimized polymer electrolytes was 3.0% under an illumination of 100 mW cm^?2. The study suggests that N,N‐dimethylformamide is a good solvent for the polymer electrolyte processing due to higher ac‐conductivity beneficial for the electrochemical device applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42489.     

Fabrication of a low‐cost nano‐SiO2/PVC composite ultrafiltration membrane and its antifouling performance

A novel low‐cost SiO₂/Polyvinylchloride (PVC) membrane with different nano‐SiO₂ particles loading (0–4 wt %) was prepared by the phase‐inversion process. The optimum nano‐SiO₂ dosage was determined as 1.5 wt % based on the casting solution compositions, the membranes' mechanical properties and hydrophilicities, the pure water fluxes, microstructures, and absorption of protein. Compared with the bare membrane, the membrane with 1.5 wt % nano‐SiO₂ addition presented better capabilities against the protein absorption and bacterial attachment, better antifouling performance, and higher flux recovery ratio in filtration of the supernatant liquor which collected from a secondary sedimentation tank in a municipal wastewater plant. The SiO₂/PVC membranes have applicable potential in the municipal wastewater treatment for their low price, good antifouling performance and high removal efficiencies of SS (over 97.2%), COD (up to 82.9%) and total bacteria (more than 93.6%). © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41267.     

Preparation and properties of core–shell nanosilica/poly(methyl methacrylate–butyl acrylate–2,2,2‐trifluoroethyl methacrylate) latex

A core–shell nanosilica (nano‐SiO₂)/fluorinated acrylic copolymer latex, where nano‐SiO₂ served as the core and a copolymer of butyl acrylate, methyl methacrylate, and 2,2,2‐trifluoroethyl methacrylate (TFEMA) served as the shell, was synthesized in this study by seed emulsion polymerization. The compatibility between the core and shell was enhanced by the introduction of vinyl trimethoxysilane on the surface of nano‐SiO₂. The morphology and particle size of the nano‐SiO₂/poly(methyl methacrylate–butyl acrylate–2,2,2‐trifluoroethyl methacrylate) [P(MMA–BA–TFEMA)] core–shell latex were characterized by transmission electron microscopy. The properties and surface energy of films formed by the nano‐SiO₂/P(MMA–BA–TFEMA) latex were analyzed by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy/energy‐dispersive X‐ray spectroscopy, and static contact angle measurement. The analyzed results indicate that the nano‐SiO₂/P(MMA–BA–TFEMA) latex presented uniform spherical core–shell particles about 45 nm in diameter. Favorable characteristics in the latex film and the lowest surface energy were obtained with 30 wt % TFEMA; this was due to the optimal migration of fluorine to the surface during film formation. The mechanical properties of the films were significantly improved by 1.0–1.5 wt % modified nano‐SiO₂. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and properties of nano‐Al2O3 particles/polyester/epoxy resin ternary composites

This article presents the results of an experimental study on the preparation and properties of new ternary composites composed of nano‐Al₂O₃ particles, polyester, and epoxy resin. The ternary composites were prepared by the addition of the nano‐Al₂O₃ particles in a binary matrix, with elevated viscosity, of the epoxy resin modified by the polyester. The nano‐Al₂O₃ particles were previously located and dispersed in the polyester phase. The study showed that the ternary system was a type of nanoscale dispersed composite with high strength and toughness as well as modulus, combined with excellent dielectric and heat‐resistance properties. All related properties of the composites were remarkably superior to those of both the binary matrix and the unmodified epoxy resin. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 70–77, 2002     

Effect of amphoteric dispersant on the dispersion properties of nano‐SiO2 particles

An amphoteric polycarboxylate dispersant (APC) was synthesized by copolymerization of acrylic acid (AA), methacryloxyethyltrimethyl ammonium chloride (DMC), and isopentenol polyoxyethylene ether (IPEG). The molecular structure of APC was characterized by FT‐IR, ¹H‐NMR, and GPC. Effect of the dosage of APC on the rheological performance of nano‐SiO₂ suspension was investigated by measurements of the plastic viscosity. The results indicated that the best dispersion effect of APC was obtained when the dosage of APC was about 10 wt % (by the weight percent of nano‐SiO₂), which can maintain the dispersion of nano‐SiO₂ suspension uniformly for 4 h without settlement. Meanwhile, the zeta potential value on the surface of nano‐SiO₂ particles shows that the better dispersion performance of APC was attributed to the solvation water film formed by the polyoxyethylene side chains and the electrostatic repulsion formed by positively groups (C?N⁺) on the APC structure combined with ‐SiO^– groups on the surface of nano‐SiO₂ particles. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45075.     

Polyurethane‐incorporated chitosan/alginate core–shell nano‐particles for controlled oral insulin delivery

Chitosan (CS) and polyurethane‐chitosan (PU‐CS) nano‐particles (NPs) were prepared for the core formation by complex coacervation method whereas alginate (ALG) and PU‐ALG were crosslinked by ionic gelation method to form the protective shell‐layer over the core. Effects of PU incorporation either within the core or shell or both were investigated by different in vitro and in vivo parameters. Fourier transform infrared (FTIR) spectroscopy of different compositions of nano‐particles showed distinct characteristic peaks for CS, PU, and ALG, indicating their presence in variable ratios. Significance of polyurethane‐incorporated systems towards insulin encapsulation efficiency, swelling parameters, insulin release, and in vivo pharmacological effect were also studied. Particle sizes, zeta potential, morphological analysis, mucoadhesion study, and in vivo acute toxicity studies of these core–shell nano‐particles were also performed. Bioavailability of insulin ranged from 9.04% to 11.6% for polyurethane‐incorporated chitosan‐alginate core–shell nano‐particle formulations which was significantly higher than the insulin bioavailability of basic CS/ALG core–shell nano‐particle system. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46365.