Synergistic effect of aluminum hydroxide and expandable graphite on the flame retardancy of polyisocyanurate–polyurethane foams

For the first time, expandable graphite (EG) and aluminum hydroxide (ATH) was combined to improve the flame retardancy of polyisocyanurate–polyurethane (PIR–PUR) foam. The limited oxygen index increased from 26.5 for the PIR–PUR matrix to an incredible value of 92.8 when 24 phr (parts per 100 of matrix) EG and 60 phr ATH were incorporated into the matrix. Based on morphology observation and thermogravimetric analysis, it was speculated that two factors contributed to the improvement of flame retardancy primarily. First, ATH could effectively induce “villi” like particles, which was useful to form a dense char. The compact char layer could effectively impede the transport of bubbles and heat. Second, ATH and EG accelerated the initial degradation and fluffy char was quickly generated on the surface of the composites. Thus, the degradation of the composite was slowed down and the diffusion of volatile combustible fragments to flame zone was delayed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39936.     

Liquid‐type nucleating agent for improving thermal insulating properties of rigid polyurethane foams by HFC‐365mfc as a blowing agent

The effects of liquid‐type additives on the morphology, thermal conductivity, and mechanical strength of polyurethane (PUR) foams were investigated. The PUR foams synthesized with perfluoroalkane showed a smaller average cell diameter and a lower thermal conductivity than PUR foams prepared with propylenecarbonate or acetone. The average cell diameter of the PUR foams decreased from 228 to 155 μm and the thermal conductivity decreased from 0.0227 to 0.0196 kcal/mh °C when the perfluoroalkane content was 0.0 to 2.0 php (parts per hundred polyol by weight). The perfluoroalkane likely acted as a nucleating agent during the formation of the PUR foams. The addition of perfluoroalkane induced the smaller cells size of the PUR foams probably due to lower surface tension of the polyol and perfluoroalkane mixture, resulting in high nucleation rate. The smaller cell size appears to be the main reason for the improvement in the thermal insulating and the mechanical properties of these PUR foams. The compressive strength of the PUR foams prepared with perfluoroalkane was higher than the PUR foams prepared with the propylenecarbonate and acetone. Based on the morphology, thermal conductivity, and compressive strength, it is suggested that the perfluoroalkane is an efficient liquid‐type additive for the improving the thermal insulation of PUR foams. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43557.     

Development of water‐blown bio‐based thermoplastic polyurethane foams using bio‐derived chain extender

Water‐blown bio‐based thermoplastic polyurethane (TPU) formulations were developed to fulfill the requirements of the reactive rotational molding/foaming process. They were prepared using synthetic and bio‐based chain extenders. Foams were prepared by stirring polyether polyol (macrodiol), chain extender (diol), surfactant (silicone oil), chemical blowing agent (distilled water), catalyst, and diisocyanate. The concentration of chain extender, blowing agent, and surfactant were varied and their effects on foaming kinetics, physical, mechanical, and morphological properties of foams were investigated. Density, compressive strength, and modulus of foams decrease with increasing blowing agent concentration and increase with increasing chain extender concentration, but are not significantly affected by changes in surfactant concentration. The foam glass‐transition temperatures increase with increasing blowing agent and chain extender concentrations. The foam cell size slightly increases with increasing blowing agent content and decreases upon surfactant addition (without any dependence on concentration), whereas chain extender concentration has no effect on cell size. Bio‐based 1,3‐propanediol can be used successfully for the preparation TPU foams without sacrificing any properties. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of different concentration of rapeseed‐oil‐based polyol and water on structure and mechanical properties of flexible polyurethane foams

Flexible polyurethane foams (FPURFs) with varied concentration of water from 3.2 to 4.2% and rapeseed oil based polyol (ROP) in the range of 13–22% in polyol premix were obtained. Effects of changes in polyurethane (PUR) formulation on the foaming process and mechanical properties of FPURFs were analyzed. It was found that the change of water content in PUR formulation influences its foaming process. Higher water content in the PUR formulation increases the growth velocity and the temperature of reaction mixture. In the case of foams modified with ROP, an opposite effect can be observed, where higher content of that component resulted in overall downturn of the foaming process and decreases of registered temperature inside the foams core. An addition of ROP beneficially influences on foams cellular structure favoring creation of finer cells. Such modification of PUR formulation with ROP increased apparent density, reduced hardness, and resilience of flexible foams. What is more the support factor of FPURFs with ROP was higher in comparison to the reference foam. Along with higher water content in the PUR formulation, apparent density and hardness has decreased and foams ability to absorb energy has been increased. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42372.     

Pulverized polyurethane foam particles reinforced rigid polyurethane foam and phenolic foam

Polyurethane consumption has been increasing in recent years, raising concerns about how to deal with the polymer waste. Post‐consumer rigid polyurethane foams or polyurethane foam scraps (PPU) ground into particles were utilized to strengthen mechanical properties of rigid polyurethane foam (PUF) and phenolic foam (PF). Viscosity of prepolymer with PUF was measured and PPU was well dispersed in prepolymer, as observed by optical microscope. Microstructures and morphologies of the reinforced foam were examined with scanning electron microscope (SEM) while cell diameter and density were measured by Scion Image software. Universal testing machine was employed to optimize compressive properties at various weight ratios of PPU. Both PUF and PF with 5 wt % PPU, respectively, exhibited considerable improvement in mechanical properties especially compressive property. The compressive modulus of PUF with 5 wt % PPU was 12.07 MPa, almost 20% higher than pure PUF while compressive strength of PF with 5 wt % PPU reached 0.48 MPa. The thermal stability of the reinforced foam was tested by thermal gravity analysis (TGA) and the result shows no obvious impact with PPU. The decomposition temperatures of PUF with PPU and PF with PPU were 280°C, because PPU has relatively weak thermal stability. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39734.     

Flexible polyurethane foams modified with biobased polyols: Synthesis and physical‐chemical characterization

A series of flexible polyurethane foams with different polyol compositions were synthesized through the replacement of a portion of the petroleum‐based polyether polyol with biobased polyols, namely, glycerol (GLY) and hydroxylated methyl esters (HMETO). HMETO was synthesized by the alkaline transesterification of tung oil (TO; obtaining GLY as a byproduct) and the subsequent hydroxylation of the obtained methyl esters with performic acid generated in situ. FTIR spectroscopy, ¹H‐NMR, and different analytical procedures indicated that the hydroxyl content increased significantly and the molecular weight decreased with respect to those of the TO after the two reaction steps. The characterization of the obtained foams, achieved through the measurement of the characteristic reaction times, thermal and dynamic mechanical analysis, scanning electronic microscopy, and density measurements, is reported and discussed. The most important changes in the modified foams were found with the addition of GLY to the formulation; this led to an increased foam density and storage rubbery modulus, which were associated with a higher crosslinking density because of the decrease in the chain length between crosslinking points. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43831.     

Rapeseed oil‐based polyurethane foams modified with glycerol and cellulose micro/nanocrystals

A rapeseed oil‐based polyol (ROPO) was synthesized using chemical modification of the rapeseed oil (RO) by epoxidation reaction followed by oxirane ring‐opening with diethylene glycol. The ROPO was used in the formulation of low‐density green polyurethane (PU) foams. The use of glycerol as hydroxyl component, water as a reactive blowing agent and micro/nanocellulose (MNC) as a reinforcement increases the content of natural components in the formulations with important effects on the final foam properties. The ROPO and their intermediate products are characterized by analytical techniques and FTIR spectroscopy, while the final PU foams are characterized by morphological and mechanical analysis. The results show that the addition of glycerol increases the modulus and yield stress. The incorporation of MNC in small amounts is enough to increase the modulus at low temperatures. Both modifiers cause an increase in water absorption and the fragility of the cell walls, reflected in the micrographs of the foams. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41602.     

Relationship between the thermal degradation chemistry and flammability of commercial flexible polyurethane foams

In this article, we report the use of a variety of analytical methods, in particular, solid‐state ¹H‐NMR and ¹³C‐NMR to characterize the relationship between the condensed‐phase chemistry and burning behavior as determined by a series of combustion tests for two commercially derived flexible polyurethane foams, one combustion‐modified. The combustion tests showed that the foams met several regulatory requirements in terms of their fire performance, whether or not they were combustion‐modified. Both foams passed the MV SS 302 and CAL 117 small‐flame tests. The nonmodified foam failed the Crib 5 test, but this test had a much larger ignition source. The particular problem with the nonmodified foam was melt drip into the flame zone. This led to a steady maintenance of the fuel feed and a rapid escalation of the fire. In contrast, the combustion‐modified foam showed little melt drip and self‐extinguished. Thermal analysis data for the two foams showed that melamine acted in part as an endothermic heat sink. This alone did not account for the much reduced melt flow and drip of the combustion‐modified foam, but the solid‐state ¹H‐NMR data clearly showed that the molecular mobility of the combustion char from combustion‐modified foam was lower than the unmodified foam char, which indicated that the flame‐retardant formulation in the combustion‐modified foam acted by a condensed‐phase mechanism. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3024–3033, 2006     

Improvement of nanoclays dispersion through microwave processing in polyurethane rigid nanocomposite foams

Polyurethane rigid nanocomposite foams were synthesized by in situ‐polymerization using both pristine and organically modified layered silicates. The effect of synthesis conditions, in particular the effect of different dispersing techniques, on morphology and mechanical properties of polyurethane nanocomposite foams was studied. To promote dispersion, clays were dispersed either in polyols or isocyanate and were subjected to a well known dispersion method, like ultrasonication, but also to a new dispersion method, based on microwaving. The morphological characterization of the foams, carried on using X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy, proved that the technology based on microwave processing is able to provide very good silicates dispersion and requires very short application time to be effective. Further confirmations of the importance of the clay organo‐modifier are still present. Mechanical characterization of foams show that clay interferes with H‐bond formation and then the overall compressive performance of PU nanocomposite foams depends on the competition between the positive reinforcing effect of clay and the negative effect on H‐bond formation. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effects of expandable graphite and dimethyl methylphosphonate on mechanical,thermal, and flame‐retardant properties of flexible polyurethane foams

Expandable graphite (EG) and dimethyl methylphosphonate (DMMP) were added to polyurethane to form flame‐retardant high‐resilience flexible polyurethane foam (FPUF) in one‐step. The effects of EG and DMMP on cell morphology, mechanical properties, dynamic mechanical properties, thermal degradation, and flame‐retardant properties of FPUF were studied. The results indicated that adding proper amount EG or/and DMMP would not seriously damage cell morphology and mechanical properties. Dynamic mechanical analysis (DMA) demonstrated that there were two tan δ peaks attributed to soft and hard segment seperately and 15 pbw EG or/and 15 pbw DMMP could enhance damping property of FPUF. Thermogravimetric analysis–Fourier transform infrared spectroscopy (TGA–FTIR) results indicated that 15 pbw EG or 15 pbw DMMP could improve the thermal stability of the second degradation step but there were no synergistic effect between the two. DMMP made FPUF composites produce more toxic gases such as CO, however, EG displayed an opposite effect. Both EG and DMMP could effectively improve the flame retardant properties of FPUF, and there was synergistic effect between the two. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 916‐926, 2013     

Foam stability and polymer phase morphology of flexible polyurethane foams synthesized from castor oil

Foam stability and segmented polymeric phase morphology of polyurethane foams synthesized partially and completely from castor oil are investigated. Preliminary analysis of the impact of alterations in the polymeric phase on macroscopic stress dissipation in foams is also carried out. The stability and morphology show unique trends depending on the concentration of castor oil used in foam synthesis. While low and intermediate concentrations of castor oil does not significantly affect the foaming process; at high concentrations, the volumetrically expanding liquid matrix remains in a nonequilibrium state during the entire foaming period, resulting in significant foam decay from top. This increases the final foam cell density and decreases the plateau border thickness at bottom. In the polymeric phase of castor oil based foams, the fraction of monodentate urea increases at the cost of non‐hydrogen bonded urea. These monodentate urea domains undergo flocculation in foams synthesized completely from castor oil, thus prominently modifying the segmented morphology. The glass transition temperature of soft segments of partially substituted foams shows moderate increase, with indications of phase mixing between the polyether and castor oil generated urethane domains. Foams synthesized entirely from castor oil have significant sol fraction due to unreacted oligomers. The microscopic alterations in polymeric phase reduce the elastic recovery of partially substituted castor oil foams compared to its viscous dissipation under an applied stress. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40668.     

Preparation and properties of a novel flame retardant polyurethane quasi‐prepolymer for toughening phenolic foam

A novel phosphorus‐ and nitrogen‐containing polyurethane quasi‐prepolymer (PNPUQP) was synthesized and incorporated into phenolic foam (PF) in different ratios in order to improve the toughness. The structure of PNPUQP was confirmed by Fourier transform infrared (FTIR) spectroscopy and nuclear magnetic resonance (NMR). The effects of PNPUQP on the flame retardant properties, thermal stability and mechanical properties of modified PF were investigated. The results suggested that the addition of 3 wt % PNPUQP increased the toughness of PF and improved the flame retardancy. The investigation on the morphology of PF and modified PF by scanning electron microscope (SEM) certified the good toughness of the PNPUQP on PF. Additionally, the thermal properties of the foams were investigated by thermogravimetric analysis (TGA) under N₂ atmosphere. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42424.     

Effects of the functionality of polyol in rigid polyurethane foams

Rigid polyurethane foams (RPUFs) have been fabricated from crude MDI (CMDI) and polypropylene glycols (PPGs) of various functionalities (f) with HFC 365mfc as a blowing agent. Foam density increased, cell size and density distribution decreased with increasing f while the closed cell content was kept constant over 92%. The gel time, tack‐free time, volume change, and the thermal conductivity of the foam showed a minimum with f = 5, and the existence of minimum has been explained in terms of a large mixture viscosity and cell wall resistance. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polyurethane foams made from liquefied bark‐based polyols

Liquefaction is known to be an effective method for converting biomass into a polyol. However, the relationships between bark liquefaction conditions and properties of the resulting foams are unclear. In this study, polyurethane foams (PUF) were made using bark‐based polyols obtained through liquefaction reactions of bark at two different temperatures (90 and 130°C). Through systematic characterization of the PUFs the influence of the liquefied bark and liquefaction conditions on foam properties could be observed. The bark‐based foams had similar foaming kinetics, thermal stability, and glass transition temperatures compared with the PEG‐based control foam. The bark‐based PUF from the polyol obtained at the higher liquefaction temperature showed comparable specific compressive strength to the PEG‐based control foam. Lastly, both bark foams exhibited a high amount of open‐cell content, with the foam made from the lower temperature liquefied polyol having poor cell morphology. This deviation from the controls in the open‐cell content may explain the lower modulus values observed in the bark PUFs due to the lack of cell membrane elastic stretching as a strengthening mechanism. These results demonstrated the influence of the bark liquefaction conditions on foam properties, thereby providing a better fundamental understanding for the practical application of bark‐based PUFs. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40599.     

Castor oil and PEG‐based shape memory polyurethane films for biomedical applications

A series of polyurethane film were prepared from poly(ethylene glycol) with different molecular weight (PEG 1500, 3000, and 8000) and castor oil by one‐shot bulk polymerization method. Hexamethylene diisocyanate and 1,4‐buthane diol were used as diisocyanate and chain extender, respectively. In order to characterize the samples, their density, swelling ratio, water contact angle, surface free energy, gel content, thermal, and viscoelastic properties were determined. The effect of the soft segment length (SSL) and hard segment content (HSC) of all polyurethane films on their shape memory behavior such as shape fixity (R_f) and shape recovery (R_r) rates were investigated by bending test. Direct contact and MTT tests were used for assessment of cell adhesion and proliferation. The relatively high R_f and R_r values were obtained for the samples programmed at high temperature difference. R_f increased with decreasing HSC. On the other hand, R_r tended to decrease with increasing SSL. After evaluating experimental data by a nonlinear equation, it was found that HSC is more effective parameter on shape memory property than SSL. The gel content, swelling ratio, and water contact angle of the samples were dependent on both SSL and HSC in their structures. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40590.     

Preparation and characterization of waterborne polyurethane containing PET waste/PPG as soft segment

Soft drinks poly(ethylene terephthalate) (PET) bottles were depolymerized by glycolysis using a 1 : 3 molar ratio of PET repeating unit to glycols like neopentyl glycol (NPG) and dipropylene glycol (DPG). Further, a series of waterborne polyurethanes (WPUs) was synthesized using pure polypropylene glycol (PPG), and glycolyzed oligoesters/PPG blends in different molar ratios as soft segment. Thermal property of WPU was tested by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Moreover, viscosity and particle size of WPU were also investigated. The results show that introduction of a certain amount of glycolyzed oligoester to soft segment makes the degree of hard‐soft domain microphase separation smaller, and can also improve thermal stability of WPU. Furthermore, WPUs synthesised from glycolyzed oligoesters and PPG blends possess larger particle size, better particle size distribution, relative lower and more stable viscosity. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42757.     

Effect of zinc oxide on properties of phenolic foams/halogen‐free flame retardant system

A halogen‐free flame retardant system consisting of ammonium polyphosphate (APP) as an acid source, blowing agent, pentaerythritol (PER) as a carbonific agent and zinc oxide (ZnO) as a synergistic agent, was used in this work to enhance flame retardancy of phenolic foams. ZnO was incorporated into flame retardant formulation at different concentrations to investigate the flammability of flame retardant composite phenolic foams (FRCPFs). The synergistic effects of ZnO on FRCPFs were evaluated by limited oxygen index (LOI), thermogravimetric analysis (TGA), cone calorimeter tests, and images of residues. Results showed that the flame retardant significantly increased the LOI of FRCPFs. Compared with PF, heat release rate (HRR), total heat release (THR), effective heat of combustion (EHC), production or yield of carbon monoxide (COP or COY) and Oxygen consumption (O₂C) of FRCPFs all remarkably decreased. However specific extinction area (SEA) and total smoke release (TSR) significantly increased, which agreed with the gas‐phase flame retardancy mechanism of the flame retardant system. The results indicated that FRCPFs have excellent fire‐retardant performance and less smoke release. And the bending and compression strength were decreased gradually with the increase of ZnO. The comprehensive properties of FRCPFs were better when the amount of ZnO was 1～1.5%. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42730.     

Sustainable rigid polyurethane foams based on recycled polyols from chemical recycling of waste polyurethane foams

The preparation and characteristics of rigid polyurethane foams (RPUFs) based on recycled polyol obtained by glycolysis of waste RPUF scraps from end-of-life refrigerators were investigated. To deactivate the amine adducts derived from isocyanates, the recycled product obtained after depolymerization was chemically modified via addition polymerization of propylene oxide. Two kinds of recycled polyols with different hydroxyl values and viscosity were blended with conventional virgin polyether polyol to prepare the RPUFs. The effects of the recycled polyols on the physical properties of RPUFs such as cell structures, compressive strength, thermal conductivity, and limiting oxygen index were discussed. It was found that the RPUFs from recycled polyols showed superior compressive strength, thermal insulation property, and self-extinguishing property compared with conventional control foam. The results of this study reveal that the recycled polyols could be used as feedstock for RPUFs with superior performance. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47916.     

Water‐blown polyurethane/polyisocyanurate foams made from recycled polyethylene terephthalate and liquefied wood‐based polyester polyol

Depolymerized polyethylene terephthalate and liquefied wood polyesters can be used as a polyol for the production of polyurethane/polyisocyanurate foams. In this research, liquefied wood was synthesized by using a combination of diethylene glycol and glycerol and due to the possibility of using glycerol that is a by‐product in biodiesel production, our goal was to use as much glycerol in the liquefaction reagent as possible. We determined the properties of the polyols, properties of produced foams, and explained their correlation. Greater amount of glycerol in the liquefaction reagent resulted in higher OH number, molecular weight, functionality, and viscosity of the polyol, as well as in longer cream time and tack free time in foam preparation. Glass transition temperature, density, and water absorption of the foam increased with increasing amount of glycerol in liquefied wood. Compressive stress increased up to 30% of the glycerol in the reagent and then reduced, while thermal conductivity was not affected. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41522.     

New compounds for production of polyurethane foams

A method of boroorganic compound preparation with boric acid, 1,3‐propanediol, 2,3‐butanediol, and 1,4‐butanediol is described in this article. The obtained compounds were characterized with respect to their usability as polyol components for the production of polyurethane (PUR) foams. New boroorganic compounds were applied as polyol components for the foaming of rigid PUR–polyisocyanurate (PIR) foams. The method of preparation, foaming parameters, and physicochemical properties of the PUR–PIR foams and their results are presented. Application of the prepared borates as polyol components in the production of foams had a favorable effect on the properties of the foams. The obtained rigid foams were characterized by lower brittleness, higher compressive strength, content of closed cells, and considerably reduced flammability in comparison with standard foams. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5918–5926, 2006