Marginal adaptation of resin-bonded light-cured glass ionomers in dentin cavities

PURPOSE: To investigate the marginal adaptation of resin-modified glass ionomer cements in dentin cavities placed with or without additional application of resin bonding systems. MATERIALS AND METHODS: Three resin-modified materials (Fuji II LC, Photac-Fil, Vitremer), one compomer (Dyract) and as reference an adhesively bonded resin composite system (Gluma CPS-Pekafill) were used. Flat peripheral dentin surfaces on human molar teeth were produced by wet grinding on SiC paper. Cylindrical cavities, 3.5 mm wide, were prepared in these dentin areas and restored with the individual materials. Sixty cavities were pretreated and restored as requested by the respective manufacturers. Following water storage of the specimens for 15 minutes or 24 hours, excess was gently removed by wet grinding for microscopic inspection of the marginal area. Additionally, in 30 cavities an experimental one-component adhesive resin system, a proprietary dimethacrylate and HEMA mixture dissolved in acetone, was combined with each of the restoratives for evaluation after 15-minutes water storage. Finally, in six cavities each, Dyract was combined with Prime and Bond 2.0, and Vitremer with Scotchbond Multi-Purpose Plus for assessment after 15 minutes. Maximum marginal gap widths (MGW) were measured. One-way ANOVA by ranks (Kruskal-Wallis-Test) followed by Wilcoxon's Two-Sample test were used to study the statistical difference of MGW among the treatment groups at a rejection level P = 0.05. RESULTS: Neither the conventionally placed material systems nor the restorations in combination with adhesives showed consistently gap-free margins after 15-minute water storage. After 24-hour storage with Vitremer 4 of the 6 restorations were gap-free, whereas with all other materials only perfect margins were registered. There was, however, no significant difference between the groups. Application of the experimental and/or the specific resin bonding agents had no effect on early MGW except for the Photac-Fil group, which was significantly reduced.     

Polymerisation shrinkage around composite resin restorations--an in vitro study

The aim of this study was to determine the degree of penetration of a fluorescent adhesive at the margins of 3 brands of posterior composite resin restorative materials. Seventy-eight extracted human premolar teeth were used. Class II cavities were prepared on both approximal surfaces of each tooth in such a manner that the gingival wall was situated apical to the amelo-cemental junction. The enamel of the cavity walls was bevelled, etched and treated with the enamel bonding agent recommended by the manufacturer. The 3 brands of composite resin used were: Fulfil, Estilux Posterior and P 50. The teeth were divided at random into 3 groups of 26 premolars each. The mesial and distal cavities of each tooth in the group were filled with the same brand. The resin was inserted in two increments in both the mesial and distal cavities and polymerised. The margins of one restoration in each tooth was coated with fluorescent adhesive and cured. All the restored teeth were embedded in clear epoxy resin and then sectioned. The mounted sections were examined at 100X magnification with fluorescent light. The polymerisation contraction gap at different areas of the tooth/restoration interface and the degree of penetration of the fluorescent adhesive into the gap was determined. The fluorescent adhesive penetrated the contraction gaps in all 3 posterior restorative materials to varying degrees. The defects observed were similar in all 3 brands and the differences in degree of penetration were not statistically significant (p > 0.05).     

Resin-modified glass ionomers for luting posterior ceramic restorations

OBJECTIVES: Until recently, esthetic inlay restorations in posterior teeth have been limited to cavities surrounded by enamel. Dentin adhesive systems in combination with luting composites and light-cured resin-modified glass ionomer cements offer a possibility for bonding ceramic inlays to cavities when the cervical margin is in dentin. This study was designed to compare in vitro marginal integrity of ceramic inlays bonded to dentin to restorations placed in cavities with margins located entirely in the enamel. METHODS: In the present in vitro study, the sealing abilities of a dentin bonding agent/luting composite combination (Syntac/Dual Cement, Vivadent) and resin-modified glass ionomers (Photac Fil, Photac Bond, ESPE; Dyract, De Trey Dentsply; Fuji II LC, GC Dental Industrial Corp.; and Vitremer, 3M Dental Products) used as luting agents in cavities extending beyond the cemento-enamel junction, were compared to the sealing abilities of a conventional luting composite (Vita Cerec Duo Cement, Vita) in cavities within sound enamel. SEM analysis and dye penetration were performed to evaluate marginal integrity at the cervical cavity margins. RESULTS: The dentin bonding agent/luting composite combination (Syntac/Dual Cement) rendered a marginal seal within the dentin similar to the quality obtained with the conventional luting procedures within sound enamel. When three out of the five resin-modified glass ionomers were used as luting agents (Dyract, Fuji II LC and Vitremer), the results were comparable to those reported for the dentin bonding agents and the conventional method. SIGNIFICANCE: Light-cured resin-modified glass ionomer cements may be considered as an alternative to dentin bonding agents when the cavity margins of ceramic inlay restorations are within the dentin. However, further studies, e.g., wear resistance, must be performed.     

Increased apoptotic cells in bone marrow biopsies from patients with aplastic anaemia

PURPOSE: To evaluate the 2-year clinical performance of two polyacid-modified resin composites and two resin-modified glass ionomers in Class V carious cavities. MATERIALS AND METHODS: A total of 120 Class V cavities were selected and 30 cavities were restored with one of two resin-modified glass ionomer materials (Fuji II LC Improved and Vitremer) and two polyacid-modified resin composites (Dyract and Compoglass) in Class V carious cavities after 2 years. The restorations were clinically evaluated after 1 and 2 years using the USPHS criteria. RESULTS: One-year findings revealed a significant difference in color match between Vitremer and other materials (P < 0.05) and no significant difference was found for the other criteria. Two-year results indicated a significant difference between resin-modified glass ionomers and polyacid-modified resin composite materials. The difference between Compoglass and Dyract was not statistically significant whereas the difference between Vitremer and Fuji II LC was statistically significant. Caries was not recorded at any evaluation period.     

Gene amplifications in advanced-stage human prostate cancer

OBJECTIVES: The pulpal reaction and the marginal sealing of in vivo restored samples using resin composite and Scotchbond Multi-Purpose adhesive system (3M Dental Products) were analyzed in this study. METHODS: Twelve Class I non-exposed cavity preparations were placed on premolars to be removed for orthodontic reasons. They were restored and observed at 7 d and 28 d. RESULTS: The examination of the resin-dentin interface under the scanning electron microscope (SEM) revealed: 1) a gap-free attachment between adhesive resin and dentinal surface in 80% of the areas studied, 2) penetration of resin tags into the dentinal tubules, and 3) formation of a 3-5 micrometer thick acid-resistant hybrid layer. Microfissures measuring about 10 micrometers were observed in only 20a% of the areas studied; these were located along the walls of the cavities, especially near the enamel in zones where there was a lower concentration of dentinal tubules. The histological analysis, carried out 7 d after preparation of the restoration, did not show any alteration of the pulp. After 4 wk, reparative dentin was produced in the pulpal areas corresponding to the restored cavities. SIGNIFICANCE: The quantity of newly formed dentin is correlated with the distance from the cavity to the pulp. The results indicate that acid-etching of vital dentin using 10% maleic acid does not impair pulpal healing in deep Class I cavities and that the Scotchbond Multi-Purpose adhesive system is able to preserve the morphological and biological integrity of the pulpo-dentinal complex.     

Microleakage of multi-step and simplified-step bonding systems

PURPOSE: To measure and compare the microleakage of Class V resin composite restorations using the following three pairs of multi- and simplified-step dentin bonding systems (DBS): OptiBond vs. OptiBond FL, All-Bond 2 vs. One-Step, and Tenure vs. Tenure Quik. MATERIALS AND METHODS: V-shaped cavities were prepared in the mesial and distal surfaces of 30 extracted human mandibular molars with margins in both enamel and cementum, and randomly assigned into three equal groups of 10 each. All DBSs were applied strictly following manufacturers' specifications before three incremental layers of resin composite (Pertac-Hybrid) were applied in all cavities. Specimens were stored for 7 days in 37 degrees C water, thermocycled for 300 cycles between 5 degrees C and 55 degrees C, immersed in 0.5% basic fuchsin solution for 24 hours, and embedded in resin before being sectioned longitudinally in multiple sections. Dye solution penetration at the tooth/composite interface was scored from 0 to 4 under a microscope at x100 at both enamel (E) and cementum (C) margins. Data were analyzed by Kruskal-Wallis and Mann-Whitney U tests with alpha = 0.05. RESULTS: OptiBond FL and One-Step showed less microleakage at the cementum margins compared to their multi-step versions. At the enamel margins Tenure Quik showed less microleakage compared to Tenure, and none of the other DBSs tested showed significant dye penetration at that interface. All DBSs showed significantly less microleakage at the enamel margins compared to the cementum margins except for OptiBond FL and One-Step that did not show any significant dye penetration at the cementum margins as well.     

Wear resistance of four luting agents as a function of marginal gap distance, cement type, and restorative material

This study investigated the effect of marginal gap width, luting cement, and restorative material on the wear resistance of the luting cement in areas where no occlusal contact is present. Three types of resin luting cement and one resin-modified glass-ionomer cement were used with two inlay systems, a resin composite, and an all-ceramic system. Bovine enamel represented tooth structure. Toothbrush abrasion was the wear modality. Three predetermined gap widths were selected: 240 +/- 30 microns, 150 +/- 30 microns, and 60 +/- 30 microns. All specimens were thermocycled. Regardless of the luting cement or the restorative material, there was a significant difference (P < 0.05) in wear resistance of the cement among the three gap distances at both the enamel and restoration interface. Vertical wear of the luting cement at the enamel interface increased linearly with marginal gap distance when all four cements were considered together (r2 > 0.51), regardless of type of restorative material used. The resin-modified glass-ionomer cement showed the least amount of wear for all variables considered. Significant differences in wear were found between the four luting cements at wide gap distances (240 microns) at the enamel interface, regardless of type of restorative material used. No significant differences were found between the two restorative materials at the enamel interface at the three gap distances.     

Resin modified glass ionomer cements. In vitro microleakage in direct class V and class II sandwich restorations

Microleakage of conventional chemically cured and resin modified glass ionomer cements (GIC), a compomer and a composite resin was studied in vitro in direct class V and class II GIC/composite sandwich fillings. None of the restorative techniques investigated completely resisted microleakage at both the occlusal and gingival margins. The dentinal gingival margins exhibited the highest leakage pattern. The compomer and the resin modified GIC showed a better seal than the chemically cured GIC's. The use of a liner as separating agent between composite resin and GIC in the class II sandwich fillings did not improve the seal. The results suggest that the initial bond obtained immediately after light curing of the resin modified GIC's is stronger than that for chemically cured GIC's. The contradictory results of dye leakage studies reported in the literature are discussed and in vivo evaluations are suggested necessary to predict clinical performance.     

Comparison of marginal fit and microleakage of ceramic and composite inlays: an in vitro study

The purpose of this in vitro study was to evaluate the marginal fit and microleakage of four types of ceramic or resin composite inlays. Sixty extracted human third molar teeth were randomly assigned into four groups. MOD cavities without bevels were prepared. The mesiogingival margin was cut in enamel, whereas the distogingival margin was placed below the amelocemental junction. The preparations and inlays were made according to the manufacturers' instructions. After acid-etching and treatment with a dentine bonding agent the inlays were cemented with dual curing CEREC resin composite luting material. After placement and polishing 10 teeth of each group were thermocycled 2500 times between 14 degrees C and 62 degrees C. Each tooth was bisectioned and from each part, one occlusal and three proximal sections of 75-100 microns thickness were cut and ground (EXAKT Cutting and Grinding system). The marginal discrepancy and the thickness of the luting cement were measured microscopically at each section and an average for each tooth was calculated. Considerable variation of marginal fit was seen, within inlays, and among different types of inlays. In general, the Vita Dur N inlays showed the best fit, e.g. the thickness of the luting cement for Vita Dur N was 114 microns occlusally and 119 microns mesiogingivally compared to 199 microns occlusally for CEREC and 219 microns mesiogingivally for Estilux. At enamel margins, a tendency of less microleakage was seen for ceramic inlays compared to composite inlays.     

In vitro evaluation of marginal and internal adaptation of class II resin composite restorations after thermal and occlusal stressing

The aim of this in vitro trial was to evaluate the external and internal adaptation of class II composite restorations to tooth structure by means of replica scanning electron microscope (SEM) observation. Standard MOD preparations were cut in human extracted teeth with margins located above and below the cementoenamel junction. Cavities were restored with either a direct multilayered technique, inlays (using conventional or dual DBA application) or prepolymerized composite inserts, using similar restorative material (Syntac, Variolink and Tetric). Evaluations were performed after mechanical and thermocycling. For the marginal adaptation in enamel, the bevelled margins of the direct group resulted in higher percentages of "continuity" (92.5% mesially and 94.6% distally), while the "marginal tooth fracture" was the most commonly found defect in groups with a butt preparation (up to 29.4%, with inserts). For the marginal adaptation in dentin, "continuity" percentages varied from 59% (inlay) to 87.9% (insert). As regards the internal adaptation, results for the whole dentin interface varied from 43.1% (inlay) to 63.9% (inlay with dual bonding) of "continuity". No regional difference in internal adaptation was found between the different preparation areas, except between gingival dentin and gingival enamel (44.9% vs. 80.7% of continuity, all group pooled data). Debonding occurred only at the dentin-restoration interface and consistently took place at the top of the hybrid layer. In the present experimental conditions, the inlay or insert techniques, which make use of the Dual bonding concept, proved to have the best potential to maintain the integrity of dentin-restoration interface.     

Trans-surgical restoration of extensive Class IV defects in the anterior dentition

Direct bonding is the most commonly utilized treatment for conservative aesthetic restoration of the anterior dentition. Class IV defects require special attention due to their high incidence, particularly in young patients. One of the major challenges for the clinician in treating defects in this category is selecting the appropriate restorative composite resin material that emulates the physical and optical characteristics of dentin and enamel and conceal the fracture line at the tooth/composite interface. Class IV defects with margins violating the biologic width present another concern, since this violation often impedes the attainment of the correct anatomic contours. The learning objective of this article is to describe a technique for achieving a correct integration of the periodontium, the tooth structure, and the restorative composite resin material to achieve a high level of aesthetic excellence.     

Low-frequency ultrasound treatment of chronic venous leg ulcers in an outpatient therapy

An in vitro dye leakage study was performed to compare the sealing ability of glass ionomer, composite resin and glass ionomer/resin cement when used as restorative materials for G.V. Black class V cavities. In this research, standard Class V cavities were prepared in sound premolar teeth extracted for orthodontic reasons. The cavities were randomly divided into 3 groups. After filling the cavities with glass ionomer cement, composite resin and light curing glass ionomer/resin cement, the specimens were immersed in silver nitrate solution. Marginal microleakage at the interface between the cavity wall and restoration was evaluated. The results were analyzed by using Kruskal-Wallis and Mann Whitney U tests. Result of this in vitro study indicate that composite resin and glass ionomer/resin cement provide a better seal than glass ionomer cement.     

In vivo and in vitro evaluation of marginal integrity in ceramic inlays

The marginal integrity is an important factor for the long-term success of ceramic inlays. The long term clinical performance of porcelain inlays depends on a number of factors of which the marginal adaptation is of significant interest. The aim of this study was to determine the margin quality of adhesively luted sintered porcelain inlays both in vivo and in vitro. MOD cavities without bevels were prepared on 10 extracted human mandibular molar teeth. Using the Ducera inlay system, inlays were fired on refractory dies and luted with a dual-curing composite resin. After polishing, each, tooth was sectioned in buccal/lingual and mesial/distal directions and marginal adaptation was assessed microscopically. The mean marginal gap of 78.77 +/- 14.85 microns recorded for occlusal margins was significantly smaller than that of 128.85 +/- 34.34 microns seen at the approximal margins. For in vivo evaluation, 25 fired porcelain inlays, including 7 onlays, were placed in Class II cavities. The assessment of the marginal adaptation of inlays was made according to the scaling system used by Aberg et al. (Acta Odontol Scand 1994; 52:140-149). In 19 of the clinical cases, the restoration was contiguous with the existing anatomic form. Both in vivo and in vitro evaluations showed the margin quality of porcelain inlays to be high.     

Three-year clinical evaluation of the Clearfil Liner Bond system

Modern dental adhesive systems have improved the bond of restorative materials to mineralized tooth structures. The purpose of this study was to evaluate the clinical performance of composite restorations placed in abrasion and erosion lesions using the Clearfil Liner Bond dental adhesive system. Following ADA clinical guidelines for dentin and enamel adhesive materials, 62 facial class 5 smooth surface erosion or abrasion lesions with no undercuts and involving primarily root surfaces were restored in 25 adult male and female patients. The teeth were restored without preparations using Clearfil Liner Bond and Clearfil Photo Anterior composite resin. The clinical performance of the restorations was assessed by two examiners at baseline, 6 months, 1, 2, and 3 years using the following evaluative parameters: color match, marginal discoloration, and marginal integrity according to modified Ryge criteria; the presence or absence of recurrent decay; pre- and postoperative sensitivity; and restoration failure due to loss of retention or other causes. At the end of 3 years, four of the 55 restorations remaining in the study failed due to lack of retention (92.7% retention rate). The evaluations of the other clinical parameters demonstrated excellent performance by this system.     

Tunnel restorations. A 3 1/2-year follow up study of Class I and II tunnel restorations in permanent and primary teeth

During 1988-89, 224 patients with approximal caries in the premolar/molar regions were provided with 318 tunnel restorations. In case of perforation of the enamel in the enamel/dentin border, (23%), complete Class II-tunnel restorations with glass ionomer cement and composite resin were made. In case of "intact" enamel, (77%), partial Class I-tunnel restorations were made. The restorations were controlled at annual routine recalls and the success rate after 3 1/2 years was 74% for permanent teeth, and 10% for primary teeth. Restorations in permanent teeth, made during the second year of the study were successful in 82%, as compared with 62% for restorations made during the first year, indicating a learning effect. Failures in the permanent dentition were due to marginal ridge fracture (35%), cavitation in the approximal enamel (31%), and recurrent caries (38%). Failures in primary teeth were predominantly due to marginal ridge fractures (84%). A comparison with the longevity of conventional Class II restorations is made and the possible advantages of the present method are presented.     

An in-vitro investigation of microleakage and gap size of glass ionomer/composite resin "sandwich" restorations in primary teeth

Eighty extracted primary molars were divided into four groups of twenty teeth. Class II cavities were prepared in all teeth with equal numbers of proximal boxes having cavosurface margins either in enamel, or dentin/cementum. Each group was allocated to an open or closed sandwich technique using glass ionomer as a lining. Following the placement of the composite resin restorations, the gap size measured at the proximal box was greatest for the closed sandwich group with the cavosurface margin on enamel (0.203 microns) or dentin/cementum (0.174 microns). Microleakage scores were measured at the proximal box and were greatest for the closed sandwich group with the cavosurface margin on dentin/cementum. The best result was obtained for the open sandwich group with the cavosurface margin on enamel.     

Dexamethasone enhances macrophage colony stimulating factor- and granulocyte macrophage colony stimulating factor-stimulated proliferation of bone marrow-derived macrophages

The authors describe a study in which they placed 126 Class V composite resin restorations without mechanical retention, divided into three groups of 42, in 23 patients. They followed the performance of the restorations over a three-year period. For all three groups, restorations were placed using All-Bond 2 dental adhesive and Z100 composite resin; A.R.T. Bond and Brilliant Dentin composite; and Prisma Universal Bond 3 and Variglass VLC polyacid-modified composite resin. The authors evaluated retention as well as color stability, wear resistance, sensitivity, sulcular depth, loss of attachment, bleeding on probing and crevicular fluid flow. Based on their results, the authors propose that restoration of Class V lesions without using mechanical retention could be expected to succeed in seven of 10 restorations over a three-year period using these restorative systems.     

Influence of finishing time on marginal sealing ability of new generation composite bonding systems

Although variation in finishing techniques has been shown to affect microleakage, little research has been published on the influence of finishing time on the marginal sealing ability of new generation composite bonding systems. The objective of the present study was to evaluate the influence of finishing time on the enamel and dentine marginal sealing ability of four new generation composite systems. Two class V preparations, which were solely in enamel or dentine, were made on the buccal surfaces of 96 freshly extracted molar teeth. The teeth were randomly divided into four groups of 24 and restored with composite resin (Silux Plus) utilizing the following bonding systems: Scotchbond Multi-purpose, Fuji Bond LC, Prime & Bond 2.0 and Bisco One-step. Half of the restorations in each group were finished immediately after light polymerization and stored for 1 week. For the remaining restorations, finishing was delayed for 1 week. The storage medium was isotonic saline at 37 degrees C throughout the experiment. All restorations were then thermocycled, subjected to dye penetration testing, sectioned and scored. The results suggest that the finishing of composite restorations, bonded with the bonding systems evaluated, should be carried out immediately after light polymerization. Delayed finishing does not improve but instead can be detrimental to the marginal seal of the restorations. The effects of delayed finishing are, however, both bonding system and tissue specific.     

Value of the search for anticardiolipin antibodies during the course of systemic lupus erythematosus

This study investigates the shear bond strengths (SBS) of different products used for bonding amalgam to dentine and the marginal seal provided by these materials. The SBS test was carried out by bonding cylinders of Dispersalloy amalgam to human dentine with an intermediate layer of Amalgambond Plus, All-Bond 2, Imperva Bond/Dual or Scotch Bond Multi-Purpose was first placed. Thereafter the samples were tested to failure in the shear mode. For the microleakage test, standardized class V cavities were prepared in human molars with one cavo margin abutting enamel and another dentine/cementum. Amalgam was condensed into the cavities, pretreated with one of the products mentioned above. In addition two further groups were prepared. One receiving treatment with Polyvar varnish and the other remained untreated as the control. Microleakage was assessed with a reflecting light microscope using I.S.O. criteria and the fracture sites and marginal gaps were examined in a scanning electron microscope. Results indicate that All-Bond 2 and Amalgambond Plus induced similar SBS and Scotchbond Multi-Purpose the weakest. At both enamel and dentine/cementum junctions resin bonding agents reduced microleakage. However, this reduction was greater at the enamel interface than at the other. Varnish allowed the greatest amount of marginal leakage and leakage was similar to the untreated control. Amalgam bonding agents are more effective at preventing marginal leakage at the enamel margin than at the dentine/cementum margin. Cavity varnish is not effective in preventing microleakage around amalgam restorations. There is a correlation between shear bond strength and marginal leakage. Materials giving the highest shear bond strength also exhibited the least marginal leakage. All-Bond 2, Amalgambond Plus and Imperva Bond/Dual are recommended to improve the seal around amalgam restorations.     

Bond strengths and SEM evaluation of Clearfil Liner Bond 2

PURPOSE: To evaluate a dental adhesive system that uses a single conditioning/primer agent. MATERIALS AND METHODS: Twenty-five flat enamel and dentin bonding sites were prepared to 600 grit on human molar teeth. The Clearfil Liner Bond 2 adhesive system was used to bond Clearfil AP-X composite to both enamel and dentin. After 24 hours of water storage, shear bond strengths were determined using an Instron testing machine. Fifty V-shaped cavity preparations were prepared in human molar teeth with an enamel and cementum margin. Composite restorations were placed using the new adhesive system. The teeth were stored for 24 hours, thermocycled, stained with AgNO3 , sectioned and examined for microleakage. SEM examinations were also completed to evaluate the effects of the treatment steps on enamel and dentin surfaces. RESULTS: Mean shear bond strengths for the experimental adhesive to enamel and dentin were 28.2 +/- 4.9 and 19.4 +/- 3.1 MPa. A t-test revealed that the enamel bond strength was significantly greater (P<0.05) than the dentin strength. No marginal leakage was observed from the enamel margins of the restorations. Three restorations showed minimal leakage from the cementum margins. SEM examinations showed resin penetration into both the conditioned enamel and dentin surfaces. The adhesive system produced high bond strengths to both enamel and dentin, exhibited very minimal microleakage and was easy to use.