共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
3.
4.
工频击穿是考核高压电气设备绝缘性能的一项重要试验,工频击穿试验直接影响对绝缘性能的判断.本文结合三峡工程左、右岸及溪洛渡、向家坝电站的定子线棒出厂试验实际情况,就定子线棒的工频击穿试验的有关问题进行分析,特别是击穿电压值和升压速率的确定,探索适合大型水轮发电机定子线棒的工频击穿试验的方法. 相似文献
5.
6.
7.
8.
本文介绍了东方电机单只线棒VPI绝缘系统试验研究情况,介绍了VPI绝缘系统使用的树脂性能及云母带性能,对VPI定子线棒的绝缘结构和工艺进行了系统地试验研究,采用了国际上先进的试验方法,使定子线棒绝缘技术水平上了一个新的台阶,单只线棒VPI绝缘系统的应用使绝缘结构设计和线棒制造达到了世界先进水平,并成功应用在工作场强为3.2kV/mm、额定电压为20kV的绝缘结构上。 相似文献
9.
为了更好控制发电机定子线棒的生产质量水平,通过对定子线棒不同的击穿试验方法和数据的分析,评估定子线棒的绝缘水平。并根据比较分析的试验数据,为定子线棒的绝缘方案确定提供较为准确的绝缘水平的预估。 相似文献
10.
11.
12.
特高压线路工频参数测试干扰分析是选择适合工频参数测试方法及测试结果分析的重要基础。测试了1 000 kV皖南-浙北特高压线路正序和零序参数测试期间的干扰电压信号,分析了其频谱特征;在此基础上,通过与正序参数仿真计算值的对比分析了正序参数实际测试偏差。结果表明:皖南-浙北特高压同塔双回线路工频参数测试期间,干扰电压存在“三相不平衡性及时变性”的特点;工频法和异频法2种不同方法得到的线路参数测试结果存在一定差异;干扰电压“时变”时,线路工频参数测试宜采用异频法。 相似文献
13.
《国外电子测量技术》2014,(10)
正Qingdao,China7.16-19,2015The International Conference on Electronic MeasurementInstruments(ICEMI)is the world’s premier conference dedicated to the electronic measurement and test of devices,boards and systems that is covering the complete cycle from design,verification,test,diagnosis,failure analysis and process of manufactory and products 相似文献
14.
《国外电子测量技术》2014,(9)
正Qingdao,China7.16-19,2015The International Conference on Electronic MeasurementInstruments(ICEMI)is the world's premier conference dedicated to the electronic measurement and test of devices,boards and systems that is covering the complete cycle from design,verification,test,diagnosis,failure analysis and process of manufactory and products 相似文献
15.
16.
17.
电站锅炉停用保护剂多采用十八胺和表面活性胺。对这2种停用保护剂进行了应用效果对比研究,即对湿冷机组、空冷机组采用十八胺或表面活性胺、有无凝结水精处理系统等6台机组停机和启动过程中给水、主蒸汽和凝结水的氢电导率变化情况进行分析。研究结果表明:在停机过程和启动过程,2种保护剂均会在水汽系统中发生部分分解,导致水汽系统的氢电导率显著升高;表面活性胺和十八胺比较,使用前者,机组启停机过程可保持凝结水精处理系统正常投运,因而可使水汽质量迅速达标,对机组安全运行有利,因此推荐采用表面活性胺作为锅炉停用保护剂。 相似文献
18.
S. Y. Wu B. N. Tran F. Y. Davis C. L. Trent D. L. Edberg W. A. Geideman 《Integrated ferroelectrics》2013,141(3):281-291
Abstract Smart materials of lead-zirconate-titanate (PZT) piezoelectric ceramics have attracted attention in recent years for active vibration control, acoustic noise suppression, health monitoring and damage assessment. We at McDonnell Douglas Aerospace have been studying these ceramics for use as sensors and actuators in various space and aircraft structures. In this paper, we will report results of a recent study on active vibration control using monomorph PZT actuators. The experiments were performed on thin aluminum cantilever beams. Collocated and non-collocated sensors and actuators were employed. Two control techniques: the classical velocity feedback and adaptive feedback controls, were investigated. We have obtained significant damping and broadband vibration attenuation of greater than 30 dB using the classical control with the single-input single-output feedback approach. A 24 dB reduction has also been achieved using the adaptive control with the multiple-input single-output approach. Detailed experimental methods and results will be described. 相似文献
19.