首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 281 毫秒
1.
斯松华  方继明  张弛  许小龙  许婷  张澳 《材料保护》2021,54(4):32-35,52
为提升高铬铸铁的综合性能,以无Mo高铬铸铁和含1.0%(质量分数)Mo高铬铸铁为研究对象,对比研究了添加Mo元素对铸态高铬铸铁组织结构以及550℃亚临界处理对其组织及硬度的影响.研究表明:2种铸态高铬铸铁的主要组成相均为奥氏体、马氏体及(Cr,Fe)7C3,但含Mo高铬铸铁中奥氏体含量明显增多.铸态高铬铸铁均以亚共晶方...  相似文献   

2.
研究了亚临界热处理对16Cr-2.5Mn高铬白口铁组织转变和性能的影响,并利用TEM、SEM、XRD和M200磨损试验机分析了其硬化机制和对耐磨性的影响.研究表明:过饱和奥氏体中固溶的Cr和C在亚临界热处理时会以(Cr,Fe)23C6形式析出,残余奥氏体发生了马氏体相变,使合金产生二次硬化;亚临界热处理中,保温时间过长,将导致(Cr,Fe)23C6向M3C原位转变发生,基体组织发生珠光体转变,导致硬度和耐磨性能不同程度降低;残余奥氏体含量为10%左右时,合金获得最高硬度和最佳耐磨性能.  相似文献   

3.
邱玲  李刚  邱星武 《材料导报》2008,3(2):39-41
利用CO2轴流激光加工机对40Cr钢表面进行激光熔凝硬化处理。利用扫描电子显微镜、金相显微镜和显微硬度计研究了不同工艺下熔凝硬化层及基体的显微组织和硬度分布特征。实验表明:熔凝硬化层由熔化区、相变硬化区和热影响区组成;由表及里组织分别为极细隐晶马氏体+少量残余奥氏体、隐晶马氏体+碳化物+残余奥氏体、马氏体+回火屈氏体+铁素体。硬化层最高硬度约是基体的3倍;随着扫描速度的增加表层硬度先增加后减小,当扫描速度为2.5m·min^-1时,表层硬度最大,为1097.9HK。  相似文献   

4.
为研发耐磨性能优良、成本相对低廉的高铬铸铁,本文分别以亚共晶、过共晶的水雾化Cr15高铬铸铁粉末为原料,采用超固相线液相烧结工艺制备了烧结高铬铸铁(SHCCI),并对其显微组织、力学性能和冲击磨粒磨损工况下的耐磨性能进行对比研究。结果表明,烧结高铬铸铁主要由M7C3碳化物、马氏体和奥氏体组成;在亚共晶烧结高铬铸铁中,通过电解腐蚀萃取的M7C3碳化物三维形貌呈珊瑚状,沿晶界均匀分布,材料抗冲击耐磨性能优良;在过共晶烧结高铬铸铁中,优先形成的初生碳化物可能成为共晶碳化物的生长基底,形成核-壳结构的M7C3碳化物,沿晶界相互连接呈网状,严重割裂基体。亚共晶、过共晶烧结高铬铸铁的力学性能分别为:硬度HRC63.9、HRC64.3,冲击韧性7.92、3.04 J/cm^2,抗弯强度2112.65、1624.87 MPa。  相似文献   

5.
对航空齿轮钢16Cr3NiWMoVNbE进行真空低压渗碳热处理,研究了真空渗碳、淬火、冰冷处理以及回火工艺对材料的组织和性能的影响。结果表明:实验钢经渗碳淬火处理后,从表面到心部的组织可分为碳化物区、碳化物与针状马氏体混合区、针状马氏体区和心部板条马氏体区。在碳化物区的晶界有大量的块状Cr碳化物析出,在析出位置Ni元素较少。在针状马氏体和板条马氏体基体中细小的析出物为Nb、V、Mo微合金元素的碳化物。从渗碳钢表面到心部,随着碳浓度的降低硬度曲线呈现先升高后降低的趋势,渗层深度为0.95 mm。冰冷处理使残余奥氏体进一步转化为马氏体,使实验钢的硬度大幅度提高。  相似文献   

6.
为深入了解Mo对烧结机台车高铬铸铁篦条磨损性能的影响,模拟了相关磨损工况,通过磨损试验及扫描电镜等手段对2种不同成分的高铬铸铁篦条的耐磨粒磨损性能和耐冲蚀磨料磨损性能进行了对比研究,并简要探讨了磨损机制.结果 表明:2种试验篦条的组织均主要由奥氏体、马氏体和(Cr,Fe)7C3型碳化物组成,其中含Mo篦条的显微组织较细...  相似文献   

7.
高铬铸铁中残余奥氏体的X射线衍射定量分析   总被引:2,自引:0,他引:2  
为了消除高铬铸铁中碳化物对残余奥氏体定量的影响,采用电解方法定量萃取高铬铸铁中的碳化物。经X射线衍射分析,碳化物为(Cr,Fe)7C3。选择碳化物的(411)晶面衍射强度作为标准,测量其它峰的相对衍射强度,得出马氏体与奥氏体(200)晶面的衍射强度校正因子分别为0.12和0.44。校正了碳化物对奥氏体定量分析的影响,可提高测量精度10%以上。  相似文献   

8.
耐磨材料中残余奥氏体在磨损中的结构变化及其影响   总被引:1,自引:0,他引:1  
通过x衍射分析、薄膜透射电镜分析和亚表层硬度分析,研究了GCr15和高铬铸铁两类耐磨材料中残余奥氏体在磨料磨损中的结构变化及其影响。试验结果表明,磨损中相当数量的残余奥氏体发生马氏体转变,形成密排六方ε型马氏体,提高表面硬化程度,改善一定磨损条件下材料的耐磨性。  相似文献   

9.
高铬白口铸铁干滑动摩擦磨损特性的研究   总被引:1,自引:0,他引:1  
研究了两种碳化物 ((Fe,Cr) 2 3 C6型碳化物和 (Fe,Cr) 7C3 型碳化物 )和 3种基体组织 (共析组织、马氏体组织和奥氏体组织 )的高铬白口铸铁与淬火 4 0Cr钢对磨时的干滑动摩擦磨损特性。试验结果表明 ,与(Fe,Cr) 2 3 C6型碳化物相比 ,(Fe,Cr) 7C3 型碳化物有利于提高高铬白口铸铁的耐磨性 ,降低其摩擦系数 ;在高接触应力情况下 ,与马氏体和奥氏体基体的合金相比 ,共析组织基体的合金具有更大的摩擦系数 ,其耐磨性也更好。  相似文献   

10.
目前,有关淬火后回火温度对Cr26高铬铸铁组织及性能的研究报道不多。为此,采用XRD、OM、SEM、TEM和电子拉力试验机和洛式硬度计,研究了回火温度对Cr26高铬铸铁调质处理前后的显微组织和力学性能的影响。结果表明:调质处理前Cr26高铬铸铁中碳化物类型有M_7C_3、M_(23)C_6和M_3C_2;调质处理后Cr26高铬铸铁的显微组织得到明显改善,基体上弥散分布着细小的碳化物;抗拉强度和硬度值随回火温度的增加而降低,延伸率有所提高;回火温度为560℃左右时,抗拉强度、延伸率和硬度值分别为1 294 MPa、8.02%和38.6 HRC,有良好的力学性能。  相似文献   

11.
In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.  相似文献   

12.
Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……  相似文献   

13.
14.
We associate a variety of innovations with the term "Industry 4.0". The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...  相似文献   

15.
A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.  相似文献   

16.
On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……  相似文献   

17.
Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.  相似文献   

18.
ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.  相似文献   

19.
In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M2(B,C), (W,Mo)2(B,C), M3(B,C), M23(B,C)6 type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm2. The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K1 mill housing of bar mill.  相似文献   

20.
正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号