氧化电压对多孔阳极氧化铝膜结构及形成的影响

以草酸为电解液研究了氧化电压对多孔阳极氧化铝膜的影响,采用场发射扫描电子显微镜(FE-SEM)对多孔阳极氧化铝膜的表面形貌进行表征.结果表明:氧化电压决定多孔阳极氧化铝膜纳米孔的大小;在一定电压范围内,氧化膜厚度随氧化电压的升高而增加.电流密度与氧化时间的关系曲线表明:在不同电压下多孔阳极氧化铝膜的形成历程基本相同,但形成多孔氧化铝膜时的电流密度随氧化电压的升高而增加.XRD分析结果证实:多孔氧化铝膜由非晶态的Al2O3组成,其组成不随阳极氧化电压而变化.     

多孔氧化铝模板的制备及应用

以磷酸溶液为电解液、以高纯铝为阳极,采用两步阳极氧化法制备氧化铝模板。扫描电子显微镜(SEM)对其表面形貌分析表明,氧化铝膜为多孔结构,膜孔径随着阳极氧化电压的增大而不断增大。对阳极氧化电流密度变化分析证实,铝的阳极氧化经历了三个阶段:阻挡层的生成、多孔层的形成和多孔层的稳定生长。以制备的氧化铝膜为阴极、锌片为阳极,以硝酸锌和硼酸的混合液为电解液,采用交流电沉积方法制备了针状氧化锌纳米线。     

阳极氧化电压对多孔氧化铝膜生长过程的影响

以草酸溶液为电解质,采用两步电化学阳极氧化法制备了氧化铝有序多孔膜,研究了阳极氧化电压对多孔膜生长过程及形貌的影响. 结果表明,电流密度、生长速率及孔径、孔间距随电压的升高而增大,而膨胀因子与电压呈线性关系. 氧化铝膜的孔隙率保持在12%左右,与电压基本无关.     

铝箔腐蚀阳极氧化前处理SEM分析

为了对多孔阳极氧化铝孔洞尺寸的可控制备,分别对磷酸和草酸作为电解液进行阳极氧化研究。发现磷酸只需经一步氧化可以制备出高度有序的多孔氧化铝膜,孔洞在电压160 V时可达到300 nm,130 V时的孔洞约150 nm。经铬酸钾和磷酸混合液处理氧化膜后,可观察到阻挡层上分布的六角形结构。而草酸经两步阳极氧化后形成的孔洞很小,只有数十纳米,经扩孔后孔洞可达100 nm。     

多孔氧化铝膜的光学特性研究

采用二次阳极氧化法,制备了高度有序多孔氧化铝膜。研究了多孔氧化铝膜的光透过、光发射特性。结果表明,当波长低于290 nm时,透过性较差;在波长290~400 nm附近氧化铝膜的光透过率发生突变;当波长高于400 nm时,光透过性较好。光致发光测试表明多孔氧化铝膜在400~550 nm之间有一个较宽的蓝色发光带,发光峰在450~460 nm。发光谱的峰位与氧化电压有关,随着电压的增大发生红移。     

阳极氧化工艺对氧化铝纳米孔膜形成过程及结构的影响

采用高纯度的铝片为阳极，以铂网为阴极，在3％～5％草酸溶液中，电压在30～70V，温度控制在17～25℃范围内进行恒压阳极氧化制备氧化铝膜，并采用环境扫描电镜观察纳米孔形貌，金相显微镜测量氧化膜厚度。研究了电解电压、电解液浓度、温度等条件对氧化铝多孔膜结构的影响。结果表明：氧化膜形成速度、纳米孔孔径、胞径、孔壁厚度、氧化膜厚度受电解电压影响显著，随着电解液浓度和温度的增大，氧化膜生长速度加快，纳米孔孔径、孔壁厚度等都随之增大，在相同时间内生成的氧化膜厚度增大。     

多孔阳极氧化铝模板制备工艺的研究

以硫酸溶液为电解液,采用二次阳极氧化工艺制备高度有序的多孔阳极氧化铝模板.研究了电解液浓度、阳极氧化电压和阳极氧化温度对多孔阳极氧化铝模板形貌、孔径和孔间距的影响,并以高氯酸和丙酮的混合溶液为电解液,利用第三次阳极氧化,一步实现了多孔阳极氧化铝膜的通孔剥离,获得具有较大面积、韧性较好的通孔多孔阳极氧化铝模板.     

铝阳极氧化膜的研究进展

简述多孔氧化铝膜的性质、性能和目前在各领域的应用情况及前景.综述了用二次阳极氧化制备多孔有序氧化铝膜的方法,较为系统地介绍了预处理、电解液的种类、电解液的浓度、温度、氧化电压及超声波等因素在多孔氧化铝膜的制备过程中时其成膜成孔过程的影响.     

高度有序多孔阳极氧化铝制备工艺的研究

影响多孔阳极氧化铝(porous anodica lumina,PAA)形貌及结构等的因素有很多,如抛光铝片的表面粗糙度、电解液温度、氧化电压、氧化时间、搅拌速率等。本文采用二次阳极氧化法,以草酸为电解液,研究了高度有序AAO模板制备过程的主要工艺条件,并采用扫描电子显微镜对模板的形貌进行表征。结果表明,在电解液温度为12℃,氧化电压为40V能够得到高度有序的、孔径为80nm左右的多孔阳极氧化铝膜。     

影响多孔阳极氧化铝膜结构特性因素的研究

酸性电解液中采用电化学方法可在铝表面形成多孔阳极氧化铝膜。研究了影响膜孔径和膜厚的关键因素,包括电解液、氧化电压、温度和时间。此外,通过X-射线衍射和扫描电镜,分析了形成氧化膜的微观形貌和晶体结构。实验结果表明多孔阳极氧化铝膜结构特性依赖于采用的氧化条件、电解液、氧化时间和电压的选择。     

Insect antifeedant properties of anthranoids from the genusVismia

Vismiones and ferruginins, representatives of a new class of lypophilic anthranoids from the genusVismia were found to inhibit feeding in larvae of species ofSpodoptera, Heliothis, and inLocusta migratoria.     

Direct observation of freeze-thaw instability of latex coatings via high pressure freezing and cryogenic SEM

Despite its industrial importance, the subject of freeze-thaw (F/T) stability of latex coatings has not been studied extensively. There is also a lack of fundamental understanding about the process and the mechanisms through which a coating becomes destabilized. High pressure (2100 bar) freezing fixes the state of water-suspended particles of polymer binder and inorganic pigments without the growth of ice crystals during freezing that produce artifacts in direct imaging scanning electron microscopy (SEM) of fracture surfaces of frozen coatings. We show that by incorporating copolymerizable functional monomers, it is possible to achieve F/T stability in polymer latexes and in low-VOC paints, as judged by the microstructures revealed by the cryogenic SEM technique. Particle coalescence as well as pigment segregation in F/T unstable systems are visualized. In order to achieve F/T stability in paints, latex particles must not flocculate and should provide protection to inorganic pigment and extender particles. Because of the unique capabilities of the cryogenic SEM, we are able to separate the effects of freezing and thawing, and study the influence of the rate of freezing and thawing on F/T stability. Destabilization can be caused by either freezing or thawing. A slow freezing process is more detrimental to F/T stability than a fast freezing process; the latter actually preserves suspension stability during freezing. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004 in Chicago, IL. Tied for first place in The John A. Gordon Best Paper Competition.     

Ethanol and (−)-α-Pinene: Attractant Kairomones for Bark and Ambrosia Beetles in the Southeastern US

In 2002–2004, we examined the flight responses of 49 species of native and exotic bark and ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) to traps baited with ethanol and/or (−)-α-pinene in the southeastern US. Eight field trials were conducted in mature pine stands in Alabama, Florida, Georgia, North Carolina, and South Carolina. Funnel traps baited with ethanol lures (release rate, about 0.6 g/day at 25–28°C) were attractive to ten species of ambrosia beetles (Ambrosiodmus tachygraphus, Anisandrus sayi, Dryoxylon onoharaensum, Monarthrum mali, Xyleborinus saxesenii, Xyleborus affinis, Xyleborus ferrugineus, Xylosandrus compactus, Xylosandrus crassiusculus, and Xylosandrus germanus) and two species of bark beetles (Cryptocarenus heveae and Hypothenemus sp.). Traps baited with (−)-α-pinene lures (release rate, 2–6 g/day at 25–28°C) were attractive to five bark beetle species (Dendroctonus terebrans, Hylastes porculus, Hylastes salebrosus, Hylastes tenuis, and Ips grandicollis) and one platypodid ambrosia beetle species (Myoplatypus flavicornis). Ethanol enhanced responses of some species (Xyleborus pubescens, H. porculus, H. salebrosus, H. tenuis, and Pityophthorus cariniceps) to traps baited with (−)-α-pinene in some locations. (−)-α-Pinene interrupted the response of some ambrosia beetle species to traps baited with ethanol, but only the response of D. onoharaensum was interrupted consistently at most locations. Of 23 species of ambrosia beetles captured in our field trials, nine were exotic and accounted for 70–97% of total catches of ambrosia beetles. Our results provide support for the continued use of separate traps baited with ethanol alone and ethanol with (−)-α-pinene to detect and monitor common bark and ambrosia beetles from the southeastern region of the US.     

Methyl 2,4,6-decatrienoates Attract Stink Bugs and Tachinid Parasitoids

Halyomorpha halys (Stål) (Pentatomidae), called the brown marmorated stink bug (BMSB), is a newly invasive species in the eastern USA that is rapidly spreading from the original point of establishment in Allentown, PA. In its native range, the BMSB is reportedly attracted to methyl (E,E,Z)-2,4,6-decatrienoate, the male-produced pheromone of another pentatomid common in eastern Asia, Plautia stali Scott. In North America, Thyanta spp. are the only pentatomids known to produce methyl 2,4,6-decatrienoate [the (E,Z,Z)-isomer] as part of their pheromones. Methyl 2,4,6-decatrienoates were field-tested in Maryland to monitor the spread of the BMSB and to explore the possibility that Thyanta spp. are an alternate host for parasitic tachinid flies that use stink bug pheromones as host-finding kairomones. Here we report the first captures of adult and nymph BMSBs in traps baited with methyl (E,E,Z)-2,4,6-decatrienoate in central Maryland and present data verifying that the tachinid, Euclytia flava (Townsend), exploits methyl (E,Z,Z)-2,4,6-decatrienoate as a kairomone. We also report the unexpected finding that various isomers of methyl 2,4,6-decatrienoate attract Acrosternum hilare (Say), although this bug apparently does not produce methyl decatrienoates. Other stink bugs and tachinids native to North America were also attracted to methyl 2,4,6-decatrienoates. These data indicate there are Heteroptera in North America in addition to Thyanta spp. that probably use methyl 2,4,6-decatrienoates as pheromones. The evidence that some pentatomids exploit the pheromones of other true bugs as kairomones to find food or to congregate as a passive defense against tachinid parasitism is discussed.     

2007～2008年世界塑料工业进展

收集了2007年7月～2008年6月世界塑料工业的相关资料,介绍了2007～2008年国外塑料工业的发展情况,提供了世界塑料产量、消费量及全球各类树脂的需求量及产能情况.按通用热塑性树脂(聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂)、工程塑料(尼龙、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚)、特种工程塑料(聚苯·硫醚、液晶聚合物、聚醚醚酮)、通用热固性树脂(酚醛、聚氨酯、不饱和聚酯树脂、环氧树脂)不同品种的顺序,对树脂的产量、消费量、供需状况及合成工艺、产品应用开发、树脂品种的延伸及应用的进一步扩展等技术作了详细介绍.     

2005～2006年国外塑料工业进展

收集了2005年7月～2006年6月国外塑料工业的相关资料,介绍了2005—2006年国外塑料工业的发展情况。提供了世界塑料产量、消费量及全球各类树脂生产量以及各国塑料制品的进出口情况。作为对比,介绍了中国塑料的生产情况。按通用热塑性树脂（聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂）、工程塑料（聚酰胺、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚）、通用热固性树脂（酚醛、聚氨酯、不饱和树脂、环氧树脂）、特种工程塑料（聚苯硫醚、液晶聚合物、聚醚醚酮）的品种顺序,对树脂的产量、消费量、供需状况及合成工艺、产品开发、树脂品种的延伸及应用的扩展作了详细的介绍。