Effects of tri-valent (Cr(III)) and hexa-valent (Cr(VI)) chromium on the growth of activated sludge

The effects of Cr(VI) and Cr(III) species on the activated sludge growth rate have been assessed for a batch growth system, for a range of chromium concentration between 0 and 320 mg l(-1). Cr(VI) was found to stimulate microbial growth for concentrations up to about 25 mg l(-1), exhibiting maximum growth stimulation at 10 mg l(-1), whilst the lethal dose was found to be between 80 and 160 mg l(-1). On the other hand, Cr(III) was also found to stimulate microbial growth for concentrations up to about 15 mg l(-1), (with a maximum stimulation concentration at 10 mg l(-1)), whilst the lethal dose was found to lie between 160 and 320 mg l(-1). The results indicate that Cr(VI) is more toxic to biomass at relatively high concentrations (higher than 70 mg l(-1)) whilst it has a more pronounced growth stimulation effect at relatively smaller concentrations (less than 25 mg l(-1)), compared with Cr(III).     

Aerobic degradation of methyl tert-butyl ether in a closed symbiotic system containing a mixed culture of Chlorella ellipsoidea and Methylibium petroleiphilum PM1

The contamination of groundwater by methyl tert-butyl ether (MTBE) is one of the most serious environmental problems around the world. MTBE degradation in a closed algal-bacterial symbiotic system, containing a mixed culture of Methylibium petroleiphilum PM1 and Chlorella ellipsoidea, was investigated. The algal-bacterial symbiotic system showed increased MTBE degradation. The MTBE-degradation rate in the mixed culture (8.808 ± 0.007 mg l(-1) d(-1)) was higher than that in the pure bacterial culture (5.664 ± 0.017 mg l(-1) d(-1)). The level of dissolved oxygen was also higher in the mixed culture than that in the pure bacterial culture. However, the improved efficiency of MTBE degradation was not in proportional to the biomass of the alga. The optimal ratio of initial cell population of bacteria to algae was 100:1. An immobilized culture of mixed bacteria and algae also showed higher MTBE degradation rate than the immobilized pure bacterial culture. A mixed culture with algae and PM1 immobilized separately in different gel beads showed higher degradation rate (8.496 ± 0.636 mg l(-1) d(-1)) than that obtained with algae and PM1 immobilized in the same gel beads (5.424 ± 0.010 mg l(-1) d(-1)).     

An analysis of synergistic and antagonistic behavior during BTEX removal in batch system using response surface methodology

The removal of benzene, toluene, ethylbenzene and xylene (BTEX) as quaternary mixtures were studied in batch systems using a well-defined mixed microbial culture. The synergistic and antagonistic effects of total BTEX removal (BTEXT-RE) due to the presence of mixed substrate was evaluated through experiments designed by response surface methodology (RSM). The low and high concentrations of individual BTEX were 15 and 75 mg l(-1), respectively. The results showed that, increasing the concentration of xylene increased the cumulative BTEX removal (BTEXT-RE), however the reverse occurred when benzene concentrations were increased from low to high levels. A mixed response of increasing and decreasing trend in the BTEXT-RE value was observed when either of toluene or ethylbenzene concentration was increased. When the concentrations of individual BTEX compounds were 30 mg l(-1), the BTEXT-RE was about 58%. Complete BTEXT-RE was achieved at optimal BTEX concentrations of 48.1, 45.6, 49.3 and 56.6 mg l(-1). The RSM approach was found efficient in explaining the main, squared and interaction effects among individual BTEX concentrations on the BTEXT-RE in a more statistically meaningful way.     

Lead accumulation and tolerance characteristics of Athyrium wardii (Hook.) as a potential phytostabilizer

Lead (Pb) pollution poses great threats to human health and can trigger serious environmental consequences. Athyrium wardii (Hook.), a new plant with the potential for phytostabilization of Pb, was identified in a field survey of plant species in a lead-zinc mine tailing located in Sichuan Province, China. The growth, Pb concentration and some physiological and biochemical characteristics of mining ecotypes (ME) and non-mining ecotypes (NME) were analyzed by pot experiment employing different concentrations of Pb(NO(3))(2) in tested soil during four weeks period. The results showed that the A. wardii has a higher tolerance to excessive levels of Pb soil contamination. The concentrations of Pb in the shoots and roots of the ME were 3.5 and 3.0 times higher, respectively, than those of the NME when plants were supplied with Pb at 800 mg Pb kg(-1). A. wardii of ME showed higher bio-activities of superoxide dismutase (SOD), peroxidase (POD) and catalase (CAT) and lower concentrations of malondialdehyde (MDA) and membrane permeability under higher Pb levels, while the opposite tendency was observed in NME. These findings demonstrated that the mining ecotype of A. wardii has the potential for phytostabilization of Pb contaminated soils.     

Application of methods for assessing the geno- and cytotoxicity of Triclosan to C. ehrenbergii

The toxic effects of Triclosan (2,4,4'-trichloro-2'-hydroxydiphenyl ether) on morphology and sexual and asexual reproduction of C. ehrenbergii were examined. In addition, the genotoxic effects of Triclosan were evaluated on the same alga using the microgel electrophoresis test, also-called Comet assay. Increasing Triclosan concentrations in the range 0.125-5 mg L(-1) did not affect size and shape of the cells but had relevant effects on both chloroplast morphology and dimension. Triclosan inhibited the vegetative growth of C. ehrenbergii at 0.5 mg L(-1). The effects on sexual reproduction indicate that the number of C. ehrenbergii zygospores was significantly reduced by the application of 0.937 mg L(-1). The Comet assay showed that Triclosan treatments led to a dose-dependent DNA damage of C. ehrenbergii; 0.25 mg L(-1)caused significant genotoxic effects and higher concentrations irreversibly altered the DNA strands. These results suggest that C. ehrenbergii could represent a useful organism to evaluate the whole toxicity of pharmaceuticals and personal care products (PPCPs), giving valuable information for a risk assessment.     

Effects of Au/Fe and Fe nanoparticles on Serratia bacterial growth and production of biosurfactant

The overall objective of this study was to compare the effects of Au/Fe and Fe nanoparticles on the growth and performance of Serratia Jl0300. The nanoparticle effect was quantified not only by the bacterial growth on agar plate after 1 hour interaction with the nanoparticles, but also by its production of a biosurfactant from used vegetable oil. The nanoparticles were prepared using the foam method. The concentrations of the nanoparticles used for the bacterial interaction study were varied from 1 mg/L to 1 g/L. The test results showed that the effect of nanoparticles on the bacterial growth and biosurfactant production varied with nanoparticle type, concentrations, and interaction time with the bacteria. Au/Fe nanoparticles didn't show toxicity to Serratia after short time (1 h) exposure, while during 8 days fermentation Au/Fe nanoparticles inhibited the growth of Serratia as well as the biosurfactant production when the concentration of the nanoparticles was higher than 10 mg/L. Fe nanoparticles showed inhibition effects to bacterial growth both after short time and long time interaction with Serratia, as well as to biosurfactant production when its concentration was higher than 100 mg/L. Based on the trends observed in this study, analytical models have been developed to predict the bacterial growth and biosurfactant production with varying concentrations of nanoparticles.     

The effect of hydraulic residence time and initial COD concentration on color and COD removal performance of the anaerobic-aerobic SBR system

An anaerobic-aerobic sequencing batch reactor, SBR, was operated with a textile dyestuff (Remazol Rot RR) containing synthetic wastewater at different anaerobic-aerobic residence times (theta(Hanaerobic)=2-19 h) and initial COD concentrations (COD(0)=400-1800 mg l(-1)). The total reaction time was kept constant at 23 h in all experiments. A dyestuff biodegrading facultative anaerobic bacterial consortium called PDW was used as the dominant bacterial culture. The environmental conditions were adjusted to T=28 degrees C and pH 7. The experimental results indicated that anaerobic and aerobic residence times in SBR systems significantly affected the system's performance. Color was mainly removed under anaerobic conditions and it was almost completed within 4-6h of the anaerobic residence time with about 90% decolorization efficiency for an initial dyestuff concentration of 60 mg l(-1). The initial COD concentration did not significantly affect the system and COD(0)=500 mg l(-1) was determined as sufficient to obtain over 90% of the color, more than 85% COD removal efficiency in SBR. Higher concentrations did not improve color removal but decreased the COD removal performance of the system.     

Effects of Fe/SDS and Au nanoparticles on P. aeruginosa bacterial growth and biosurfactant production

The aim of this study was to evaluate the effects of iron (Fe)/SDS and gold (Au) nanoparticles on growth and biosurfactant production of Pseudomonas aeruginosa PBCC5. The concentrations of the nanoparticles used were 1, 500 and 1000 mg/l. In this research, the surface tension of biosurfactant, dry weight of biosurfactant and biomass, emulsification indexes (E₂₄) were measured and transmission electron microscopy analysis was used to monitor the nanoparticles. The test results showed that the effect of nanoparticles on the bacterial growth and biosurfactant production varied corresponding to the type and concentration of nanoparticles. Fe/SDS nanoparticles showed no bacterial toxicity when the concentration of nanoparticles was 1 mg/ml and increased the growth and biosurfactant production, 23.21 and 20.73%, respectively. While at higher concentrations (500, 1000 mg/l), the nanoparticles suppressed bacterial growth as well as biosurfactant production. Similarly, Au nanoparticles had no bacterial toxicity and also increased bacterial growth and biosurfactant production. The surface tensions of all samples decreased from 72 of distiled water to 32–35 mN/m.Inspec keywords: nanoparticles, iron, gold, nanofabrication, nanomedicine, surfactants, biomedical materials, surface tension, renewable materials, transmission electron microscopy, microorganismsOther keywords: Au nanoparticles, P. aeruginosa bacterial growth, biosurfactant production, Pseudomonas aeruginosa PBCC5, surface tension, biomass, emulsification indexes, dry weight, transmission electron microscopy, Fe‐SDS nanoparticles, distiled water, Fe, Au     

Bioaccumulation versus adsorption of reactive dye by immobilized growing Aspergillus fumigatus beads

The removal of reactive brilliant blue KN-R using growing Aspergillus fumigatus (abbr. A. fumigatus) immobilized on carboxymethylcellulose (CMC) beads with respect to initial dye concentration was investigated. Bioaccumulation was the dominant mechanism of the dye removal. According to the UV-vis spectra and the results of three sets of experiments, it could be concluded that the bioaccumulation using immobilized growing A. fumigatus beads was achieved by metabolism-dependent accumulation and metabolism-independent adsorption (15-23% proportion of overall dye removal), which included biosorption by mycelia entrapped in them and adsorption on immobilization matrix. The transmission electron microscope (TEM) images showed the intracellular structures of mycelia and the toxicity of dye. It was found that the fungus had a considerable tolerance to reactive brilliant blue KN-R at initial dye concentrations of <114.7 mg/l. Though at high initial dye concentrations the growth of mycelia was inhibited significantly by the dye molecules in the growth medium, the bioaccumulation capacity was not markedly affected and the maximum bioaccumulation capacity was 190.5+/-2.0 mg/g at an initial dye concentration of 374.4 mg/l. The bioaccumulation rates were not constant over the contact time.     

Superconductivity of p-type diamond (001) and (111) thin films: Ab initio calculations

The surface structure, electronic properties, lattice dynamics, and the electron-phonon coupling for p-doped diamond (001)-(2 × 1) and (111)-(2 × 1) thin films have been extensively investigated using ab initio methods within the virtual crystal approximation. The calculations of p-doped diamond thin films strongly favor dimer reconstruction of diamond surfaces. The physical origin of superconductivity of diamond (001)-(2 × 1), respectively, and (111)-(2 × 1) thin films which is higher than that of bulk diamond is systematically studied. It is showed that surface vibrational modes of diamond (001)-(2 × 1) surfaces give main contributions to superconducting transition temperature T_c, while T_c of diamond (111)-(2 × 1) surfaces is attributed to the combined action of surface and bulk vibrational modes. Therefore, at the highest concentration (13.98 × 10²¹ cm^− 3) T_c ≈ 56.5 K of diamond (111)-(2 × 1) surfaces is about twice as high as that of bulk and diamond (001)-(2 × 1) surfaces.     

Phenol degradation by Aureobasidium pullulans FE13 isolated from industrial effluents

The degradation of phenol (2-30 mM) by free cells and by alginate-immobilized cells of Aureobasidium pullulans FE13 isolated from stainless steel effluents was studied in batch cultures with saline solution not supplemented with nutrients or yeast extract. The rate at which the immobilized cells degrade phenol was similar to the rate at which the suspended cells could degrade phenol, for a concentration of up to 16 mM of phenol. The maximum phenol volumetric degradation rate for 16 mM phenol was found to be 18.35 mg l(-1)h(-1) in the assays with free cells and 20.45 mg l(-1)h(-1) in the assays with alginate-immobilized cells, 18 mM phenol and cellular concentration of 0.176 g/l. At concentrations higher than this, an inhibitory effect was observed, resulting in the lowering of the phenol degradation rates. The immobilization was detrimental to the catechol 1,2-dioxygenase activity. However, the immobilized cells remained viable for a longer period, increasing the efficiency of phenol degradation. The yeast showed catechol 1,2-dioxygenase activity only after growth in the phenol, which was induced at phenol concentrations as low as 0.05 mM and up to 25 mM at 45 h of incubation at 30 degrees C. Phenol concentrations higher than 6mM were inhibitory to the enzyme. Addition of glucose, lactate, succinate, and benzoate reduced the rate at which phenol is consumed by cells. Our results suggest that inoculants based on immobilized cells of A. pullulans FE13 has potential application in the biodegradation of phenol and possibly in the degradation of other related aromatic compounds.     

Particle-size effect of CuO and ZnO on biogas and methane production during anaerobic digestion

The effects of bulk- and nano-sized CuO and ZnO particles on biogas and methane production during anaerobic digestion of cattle manure were studied for a period of 14 days at 36 °C using the ISO 13641-2 guidelines. Biogas production was severely affected at concentrations of bulk and nanoparticles over 120 and 15 mg/L for CuO and 240 and 120 mg/L for ZnO, respectively. EC50 concentrations for methane inhibition were estimated to be 129 mg Cu/L for bulk CuO, 10.7 mg Cu/L for nano CuO, 101 mg Zn/L for bulk ZnO and 57.4 mg Zn/L for nano ZnO. The solubility of CuO nanoparticles in the reaction mixture was observed after 14 days of incubation and was significantly higher than the levels observed for ZnO. These results are of significant importance, as it is the first time that the effects of metal oxide particle size on biogas and methane production have been studied.     

COD, para-chlorophenol and toxicity removal from para-chlorophenol containing synthetic wastewater in an activated sludge unit

Chlorinated phenolic compounds present in some chemical industry wastewaters cause severe toxic effects on the organisms and often are resistant to biological degradation. Synthetic wastewater containing different concentrations of para-chlorophenol (4-chlorophenol, 4-CP) was biologically treated in an activated sludge unit for COD, 4-CP and toxicity removal. Effects of feed 4-CP concentration on COD, 4-CP, toxicity removals and on sludge volume index were investigated at a constant sludge age of 20 days and hydraulic residence time (HRT) of 25 h. Resazurin method based on dehydrogenase activity was used for determination of the toxicity of the feed and effluent wastewater. COD and 4-CP removals were not affected by the presence of 4-CP in the wastewater up to feed 4-CP concentration of 925 mg l(-1) because of almost complete degradation of 4-CP yielding lower than 50 mg l(-1) 4-CP in the aeration tank. Percent COD, 4-CP and toxicity removals decreased and the effluent COD, 4-CP and toxicity levels increased with further increases in the feed 4-CP concentrations above 925 mg l(-1) because of inhibitory concentrations of 4-CP in the reactor. Biomass concentration in the aeration tank decreased and the sludge volume index (SVI) increased with feed 4-CP concentrations above 925 mg l(-1) resulting in lower COD and 4-CP removal rates. The rates of COD and 4-CP removals indicated substrate (4-CP) inhibition for the feed 4-CP concentrations above 925 mg l(-1) corresponding to the reactor 4-CP of above 200 mg l(-1). The system should be operated at the feed 4-CP concentrations of less than 900 mg l(-1) (4-CP(R) < 200 mg l(-1)) in order to obtain high rates and extents of COD, 4-CP and toxicity removals at a sludge age of 20 days and HRT of 25 h.     

Immobilization of mercury in field soil and sediment using carboxymethyl cellulose stabilized iron sulfide nanoparticles

Mercury (Hg) is one of the most pervasive and bio-accumulative metals in the environment. Yet, effective in situ remediation technologies have been lacking. This study investigated the effectiveness of a class of soil-deliverable FeS nanoparticles for in situ immobilization of Hg in two field-contaminated soils from a New Jersey site and one sediment from an Alabama site. The nanoparticles were prepared using sodium carboxymethyl cellulose (CMC) as a stabilizer. Transmission electron microscopy measurements revealed a particle size of 34.3 ± 8.3 nm (standard deviation), whereas dynamic light scattering gave a hydrodynamic diameter of 222.5 ± 3.2 nm. Batch tests showed that at an FeS-to-Hg molar ratio of 28:1-118:1, the nanoparticles reduced water-leachable Hg by 79%-96% and the TCLP (toxicity characteristic leaching procedure) based leachability by 26%-96%. Column breakthrough tests indicated that the nanoparticles were deliverable in the sediment/soil columns under moderate injection pressure. However, once the external pressure was removed, the delivered nanoparticles remained virtually mobile under typical groundwater flow conditions. When the Hg-contaminated soil and sediment were treated with 52-95 pore volumes of a 500 mg l(-1) FeS nanoparticle suspension, water-leachable Hg was reduced by 90%-93% and TCLP-leachable Hg was reduced by 65%-91%. The results warrant further field demonstration of this promising in situ remediation technology.     

An OUR-based approach to determine the toxic effects of 2,4-dichlorophenoxyacetic acid in activated sludge

This study uses the oxygen uptake rate (OUR) measurement to measure toxicity effects of 2,4-dichlorophenoxyacetic acid (2,4-D) on activated sludges fed with the wastewater from a small domestic wastewater treatment plant and peptone-based synthetic wastewater. Two 2l lab-scale batch reactors were run in parallel with the same F/M ratios (0.4 mg COD per mg VSS per day) to assess the inhibition effects of 2,4-D concentrations between 25 and 75 mg l(-1) considering at least a 100% dilution rate, as compared with a pesticide industry effluent containing 20,000-40,000 mg l(-1) COD, reaches a central treatment plant. It was noted that the OUR was decreased to 15 and 30%, respectively, when adding 75 mg l(-1) of 2,4-D to the domestic and synthetic reactors. Meanwhile, the addition of 25 plus 50 mg l(-1) of 2,4-D in sequence to the domestic wastewater reactor did not significantly affect the OUR profile. The OUR-based inhibition definition has been used in this research since the OUR methods have been frequently used and cited in the literature to study toxicity effects. However, the origin of the sludge used in the testing is also important. Synthetic wastewater may simulate the toxicity studies but with a higher response than actual systems, since the microorganisms are considerably becoming substrate-selective.     

Impact of imidacloprid residues on the development of Eisenia fetida during vermicomposting of greenhouse plant waste

Pesticide application in agriculture causes residues in post-harvest plant waste at different concentrations. Knowledge concerning how pesticide concentrations in such waste affect earthworms is essential for recycling greenhouse plant debris through vermicomposting. Here, we have evaluated the effects of imidacloprid (IMD) residues on earthworms (Eisenia fetida) during the vermicomposting of plant waste from greenhouse crops in Spain. Before, the effect of different IMD concentrations on earthworms was tested using cattle manure as an optimum waste for worm development. The results after using cattle manure indicate that IMD dose ≥ 5 mg kg(-1) hinders worm growth and even causes death, whereas IMD dose ≤ 2 mg IMD kg(-1) allows worm growth similar to control but impedes reproduction. The results from the vermicomposting of plant waste reveal that IMD inhibits adequate worm growth and increases mortality. Although 89% worms became sexually mature in substrate containing 2 mg IMD kg(-1), they did not produce cocoons. IMD also affected microorganisms harboured in the substrates for vermicomposting, as indicated by the reduction in their dehydrogenase activity. This enzyme activity was restored after vermicomposting. This study provides a sound basis for the vermicomposting of pesticide-contaminated plant waste.     

Ferroxidase activity of apoferritin is increased in the presence of platinum nanoparticles

The ferroxidase activity of horse spleen apoferritin (HSAF) is increased by nine-fold in the presence of platinum nanoparticles. HSAF was mixed with varying concentrations of K2PtCl4 followed by a 20-fold concentration of sodium borohydride to afford Pt:HSAF nanoparticle complexes in a ratio of between 1:250 and 1:4000. Typical colour changes, from colourless or pale yellow to brown, occurred that were dependent on the amount of platinum present. These complexes were characterized by UV/vis, inductively coupled plasma optical emission spectroscopy, Fourier transform infrared, transmission electron microscopy and energy dispersive x-ray spectroscopy. Transmission electron microscopy analysis revealed that the size of nanoparticles increased as the molar ratio of platinum to HSAF increased with an average size diameter of 2-6 nm generated with HSAF:platinum molar ratios of 1:250-1:4000. Fourier transform infrared spectroscopy (FTIR) spectra showed no distinct changes in the structure of HSAF but confirmed that the nanoparticles were attached to the protein. The effect of platinum nanoparticles on the ferroxidase activity of HSAF showed a specific activity of 360 ρmol min(-1) mg(-1), (nine-fold increase over the control) at the molar ratio of HSAF:platinum nanoparticles of 1:1000.     

Measuring of critical density of heat flow during boiling of nanoliquids on a cylindrical heater

Saturated boiling of nanoliquids on a cylindrical heater is experimentally studied. The studied nanoliquids were prepared using distilled water and Fe3O4 iron oxide or diamond nanoparticles. The volume concentration of the nanoparticles was changed from 0.25 to 1%. It has been measured that the critical density of heat flow in nanoliquids is far higher than in water. Moreover, it depends on size of nanoparticles.     

Factors affecting the sorption of model environmental pollutants onto silver polydimethylsiloxane nanocomposite Raman substrates

The presence of aromatic compounds in water is an important topic in environmental sciences. Silver-polydimethylsiloxane nanocomposites (Ag-PDMS) have recently been demonstrated as promising substrates for the detection of model environmental pollutants via surface-enhanced Raman spectroscopy (SERS). This work discusses how different variables such as pH and matrix composition can affect the sorption and SERS activity of these chemicals. The results show that the conjugate base of weak acids can interact more efficiently with the substrate, leading to an increased signal at higher pH, while amino-aromatic compounds interact more efficiently at a lower pH. The sorption of these chemicals is an essential step in the process and has been attributed to the absorption of the analyte into the PDMS followed by its adsorption to the metallic surface. In addition, the presence of moderate concentrations (1 x 10(-4) M) of a supporting electrolyte such as nitrate or fluoride can improve the sorption of 4-hydroxybenzoic acid to the Ag-PDMS nanoparticles. Other ions such as phosphate and chloride cause rapid oxidation of the substrates even at concentrations as low as 1 x 10(-5) M. The effect of these variables in the analysis of real samples is presented. The potential use of liquid chromatography for isolating the model pollutants from detrimental matrix components in nat- ural waters is also shown.