Epoxy resins based on aromatic glycidylamines. IV. Preparation of N,N,N′,N′-tetraglycidyl-4,4′-diaminodiphenylmethane from aniline and analysis of the product by GPC and HPLC

Epoxy resins containing N,N,N′,N′-tetraglycidyl-4,4′-diaminodiphenylmethane (TGDDM) were prepared from aniline and epichlorohydrin and analyzed by GPC and HPLC. The product composition was compared with that of resins prepared from 4,4′-diaminodiphenylmethane (DDM) and epichlorohydrin, which had been analyzed in our previous work. A new byproduct designated Y4 was isolated by semipreparative HPLC and identified by NMR and mass spectroscopy. The course of formaldehyde condensation with N,N-dichlorohydrin of aniline (DCHA) was followed by GPC and HPLC and the mechanism of formation of Y4 was proposed on the basis of obtained results. Attention was also paid to the differences in reactivity of DCHA diastereoisomers.     

Epoxy resin based on 4,4′-dihydroxydiphenysulfone. I. Synthesis and reaction kinetics with 4,4′-diaminodiphenylmethane and 4,4′-diaminodiphenylsulfone

Epoxy resins based on 4,4′-dihydroxydiphenylsulfone (DGEBS) and diglycidyl ether of bisphenol A (DGEBA) were prepared by alkaline condensation of 4,4′-dihydroxydiphenylsulfone (bisphenol S) with epichlorohydrin and by recrystallization of liquid, commercial bisphenol A-type epoxy resin, respectively. Curing kinetics of the two epoxy compounds with 4,4′-diaminodiphenylmethane (DDM) and with 4,4′-diaminodiphenylsulfone (DDS) as well as T_g values of the cured materials were determined by the DSC method. It was found that the ? SO₂? group both in the epoxy resin and in the harener increases T_g values of the cured materials. DGEBS reacts with the used hardeners faster than does DGEBA and the curing reaction of DGEBS begins at lower temperature than does the curing reaction of DGEBA when the same amine is used. © 1994 John Wiley & Sons, Inc.     

Epoxy resins based on aromatic glycidylamines. V. Shelf life of TGDDM-based epoxy resins

The effect of aging on resin composition was investigated as a part of a study concerned with the evaluation of epoxies containing N, N, N′, N′-tetraglycidyl-4,4′-diaminodiphenylmethane (TGDDM). Long-term stability of three different epoxy resins based on TGDDM and their mixtures with 4,4′-diaminodiphenylsulfone (DDS) was followed at 23 ± 2°C at a relative humidity ranging from 45% to 55%, by means of GPC and HPLC; short-term stability of the resins was evaluated at 125°C.     

Ambipolar and multi‐electrochromic polyimides based on N,N‐di(4‐aminophenyl)‐N′,N′‐diphenyl‐4,4′‐oxydianiline

A series of novel aromatic polyimides were synthesized from N,N‐di(4‐aminophenyl)‐N′,N′‐diphenyl‐4,4′‐oxydianiline and aromatic tetracarboxylic dianhydrides through a conventional two‐step procedure. Most of the polyimides exhibited reasonable solubility in organic solvents and could afford robust films via solution casting. The polyimides exhibited high thermal stability, with glass transition temperatures in the range 227–273 °C and 10% weight‐loss temperatures in excess of 550 °C. All the polyimide films showed ambipolar redox and multi‐electrochromic behaviors. They exhibited two reversible oxidation redox couples at 0.94–0.98 and 1.09–1.12 V versus Ag/AgCl in acetonitrile solution. A coupling reaction between the radical cations of the pendent triphenylamine units occurred during the oxidative process forming a tetraphenylbenzidine structure which resulted in an additional redox state and color change. © 2014 Society of Chemical Industry     

Epoxy resins VIII. Thermal properties of 4,4′-sulfonyldiphenol and bisphenol a epoxy resins

Epoxy resins of different molecular weights were prepared from epichlorohydrin and 4,4′-sulfonyldiphenol (SDP) and from epicholorohydrin and bisphenol A (BA). They were cured at high temperatures with four different crosslinking agents, including aliphatic and aromatic amines. The thermal behaviour of these cured epoxy resins was studied. From the IPDT and IDT data it was observed that sulfone epoxy resins were thermally more stable than bisphenol A epoxy resins. The activation energies of thermal degradation of the resins were calculated and the implications of these results are discussed.     

Synthesis,characterization, and properties of low viscosity tetra‐functional epoxy resin N,N,N′,N′‐ tetraglycidyl‐3,3′‐diethyl‐4,4′‐diaminodiphenylmethane

Tetra‐functional epoxy resin N,N,N′,N′‐tetraglycidyl‐3,3′‐diethyl‐4,4′‐diaminodiphenylmethane (TGDEDDM) was synthesized and characterized. The viscosity of TGDEDDM at 25°C was 7.2 Pa·s, much lower than that of N,N,N′,N′‐tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM). DSC analysis revealed that the reactivity of TGDEDDM with curing agent 4,4′‐diamino diphenylsulfone (DDS) was significantly lower than that of TGDDM. Owing to its lower viscosity and reactivity, TGDEDDM/DDS exhibited a much wider processing temperature window compared to TGDDM/DDS. Trifluoroborane ethylamine complex (BF₃‐MEA) was used to promote the curing of TGDEDDM/DDS to achieve a full cure, and the thermal and mechanical properties of the cured TGDEDDM were investigated and compared with those of the cured TGDDM. It transpired that, due to the introduction of ethyl groups, the heat resistance and flexural strength were reduced, while the modulus was enhanced. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 40009.     

Epoxy resins based on aromatic glycidylamines. III. Kinetics of intramolecular cyclization of N,N-bis(2-hydroxy-3-chloropropyl)aniline

The course of intramolecular cyclization of N,N-bis (2-hydroxy-3-chloropropyl) aniline (DCHA) was followed by HPLC. The rate constants (at 70, 85, 100, and 115°C) and the Arrhenius parameters for individual reaction steps were determined. The resulting product was isolated by semipreparative HPLC and its structure was confirmed by NMR spectroscopy. Attention was also paid to the different reactivity of DCHA diastereoisomers.     

α-Substituierte Phosphonate. XXXI. Zur Reaktion von N,N,N′,N′-Tetramethylchlorformamidiniumchlorid mit P-III-Verbindungen

α-Substituted Phosphonates. XXXI. The Reaction of N,N,N′,N′-Tetramethyl Chloroformamidinium Chloride with P(III) Compounds N,N,N′,N′-Tetramethyl chloroformamidiniumchloride ( 4 ) does not react with triethyl phosphite (TEP) or isopropyl diphenylphosphinate to give the expected bisphosphoryl derivatives 7 and 11 , respectively, but primarily the monophosphorylated amidinium salts 6 and 10 respectively. The phosphine oxide 10 is stable, while 6 undergoes an elimination of ethyl chloride to the betain 8 . Even under more drastic conditions the reaction of 4 or 8 with TEP does not lead to the expected bis(dimethylamino)bisphosphonate 7 , but to the monoaminated bisphosphonate 1 , involving a reduction step. Similar reduction has been observed under mild conditions in Michaelis-Arbusov reaction of dichloromethylenimonium chloride, yielding the expected trisphosphonate 2 and the bisphosphonate 1 as a by-product.     

Development of green and dark blue colors in epoxy resins cured with 4,4′-diaminodiphenylmethane

From a study of the oxidation of bisphenol-A epoxy resin cured with DDM (4,4′-diaminodiphenylmethane), it has been shown that the development of greenish-blue colors is due to an initial reaction between molecular oxygen and secondary amine groups. A full reaction scheme is suggested and supporting evidence, in the form of UV/visible, infrared, and ESR spectra, is presented.     

Studies on the Synthesis of 2,2′,4,4′,6,6′-Hexanitrostilbene

The synthesis of 2,2′,4,4′,6,6′-hexanitrostilbene by oxidative coupling of 2,4,6-trinitrotoluene in the presence of metal catalysts has been studied. The effects of reaction parameters on product yields have been evaluated and mechanisms for the reaction are proposed.     

Study of reaction between N,N,N′,N′,N′-pentakis (hydroxymethyl) melamine and ethylene or propylene oxide

The effects of the kind and amount of oxirane (propylene or ethylene oxide), the amount of triethylamine catalyst, and the temperature on the reaction with N,N,N′,N′,N′-pentakis (hydroxymethyl) melamine (PHMM) in DMSO solution were studied. The changes in the content of reactive groups in the reaction mixture and in the final product were analyzed. The oxirane addition was shown to be accompanied by the condensation of hydroxymethyl groups in the PHMM. Optimal conditions for the synthesis and the structural formula of the s-triazine ring containing polyetherols were established. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 2589–2602, 1997     

Hydrodynamic properties for N,N,N′,N′‐tetraalkyl diglycolamides dissolved in n‐dodecane system

N,N,N′,N′‐tetraoctyl diglycolamide (TODGA) and N,N,N′,N′‐tetra(2‐ethylhexyl) diglycolamide (T2EHDGA) have been identified as promising extractants for actinide partitioning from high‐level nuclear waste. These extractants are proposed to be used along with suitable phase modifiers, viz. N,N‐dihexyl octanamide (DHOA), tri‐n‐butyl phosphate (TBP) and 2‐decanol dissolved in n‐dodecane. Hydrodynamic parameters, viz. density, viscosity and interfacial tension (IFT) are important for optimisation of hydrometallurgical process to ensure that there is no emulsion formation and to achieve desired phase disengagement rate. Densities and viscosities of the two extractants, viz. TODGA and T2EHDGA along with different phase modifiers have been measured over different range of compositions and temperatures (298–333 K). The viscosity data have been used to calculate the activation energy for viscous flow for each composition of solvents. The IFT values have also been measured for different solvent compositions. The viscosity and IFT data of TODGA and T2EHDGA with 2‐decanol as phase modifier appears suitable under hydrometallurgical conditions proposed for actinide partitioning. © 2011 Canadian Society for Chemical Engineering     

Kinetics of 4,4′-diaminodiphenylmethane curing of bisphenol-S epoxy resin

The kinetics of the cure reaction for a system of bisphenol-S epoxy resin (BPSER), with 4,4′-diaminodiphenylmethane (DDM) as a curing agent, were studied by means of differential scanning calorimetry (DSC). Analysis of DSC data indicated that an autocatalytic behavior showed in the first stages of the cure, with the model proposed by Kamal, which includes two rate constants, k₁ and k₂, and two reaction orders, m and n. Rate constants k₁ and k₂ were observed to be greater when curing temperature increased. The over-all reaction order, m + n, is in the range of 2.5 ∼ 3. The activation energies for k₁ and k₂ were 55 kJ/mol and 57 kJ/mol, respectively. Diffusion control is incorporated to describe the cure in the latter stages. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 1799–1803, 1999     

Synthesis of 3,3′-Bis(2,2′,4,4′,6,6′-Hexanitortilbene)

This paper describes the synthesis of 3,3′bis(2,2′,4,4′,6,6′-hexanitrostilbene) (5). Based on the Ullmann reaction we prepared the title compound in nitrobenzene by using 3-chloro 2,2′,4,4′,6,6′-hexanitroztilbene (4) as the starting material and copper powder as the catalyst. (4) was reacted with hydrazine, not to yield a desired product, azo-3,3′bist(2,2′,4,4′,6,6′-hexanitrostilbene.) but to form a well-known explosive, 2,2′,4,4′,6,6′-hexanitrostibene (6). Differential scanning calorimetrical analysis has shown that (5) begins to decompose at the temperature of 298°C.     

Reactions taking place in the system N,N,N′,N′,N″‐ pentakis(hydroxymethyl)melamine–oxirane in aqueous media

The results of studies on effects of the amount and type of oxirane, amount of catalyst and water, and temperature on the course of reactions taking place in the system N,N,N′,N′,N″‐pentakis(hydroxymethyl)melamine (PHMM)–oxirane carried out in aqueous media are reported. Quantitative determination of the content of functional groups present in the system and of side products formed in reactions of oxirane with water, made it possible to analyze in detail the processes taking place in the system. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 824–836, 2000     

Synthesis and properties of new aromatic polyimides based on 2,2′‐dibromo‐4,4′,5,5′‐benzophenone tetracarboxylic dianhydride

New polyimides with enhanced thermal stability and high solubility were synthesized in common organic solvents from a new dianhydride, 2,2′‐dibromo‐4,4′,5,5′‐benzophenone tetracarboxylic dianhydride (DBBTDA). DBBTDA was used as monomer to synthesize polyimides by using various aromatic diamines. The polymers were characterized by IR and NMR spectroscopy and elemental analysis. These polyimides had good inherent viscosities in N‐methyl‐2‐pyrrolidinone (NMP) and also high solubility and excellent thermo‐oxidative stability, with 5 % weight loss in the range 433 to 597 °C. Copyright © 2004 Society of Chemical Industry     

One-step synthesis of aromatic polyimides based on 4,4′-diaminotriphenylmethane

The feasibility of using a one-step high-temperature polycondensation for the synthesis of aromatic polyimides, based on 4,4′-diaminotriphenylmethane (DA-TPM), was studied. It was found that the reaction of DA-TPM with various aromatic dianhydrides in nitrobenzene at 180–200°C resulted in the formation of the high molecular weight soluble polyimides, PI-TPM. The reaction solutions cooled to ambient temperature were used for casting films. These PI-TPM films significantly exceeded their prototypes obtained by the thermal imidization of poly(amic acids) in terms of solubility and tensile properties. All studied polyimides demonstrated well-distinguished glass transition at 260–320°C. © 1996 John Wiley & Sons, Inc.     

Soluble aromatic polyimides and polyamides based on 4,4′-diaminotriphenylmethane

Aromatic polyamides and polyimides were synthesized from 4,4′-diaminotriphenylmethane (DA-TPM) for studying their solubility, thermal, and mechanical properties. The polymers were found to be soluble in amide solvents and pyridine, and this could be attributed to the practically free rotation of the polymer chain segments around the bridging group within the DA-TPM and the effect of its pendant phenyl ring. The polyimides and polyamides exhibited well-distinguished glass transition in the range of temperatures, which is typical for flexible-chain polymers. For the polyimides, significant differences in solubility and mechanical properties were observed between the samples prepared by chemical and thermal imidization of poly(amic acids). Thermal imidization brought about remarkably less soluble brittle films. © 1995 John Wiley & Sons, Inc.     

A Parametric Study of the Synthesis of 4,4′,5,5′,7,7′-Hexanitro-1,1′-Binaphthyl

Conditions for the synthesis of 4,4′,5,5′,7,7′-hexanitrobinaphthyl( I ) from 1,1′-binaphthyl have been investigated. It has been found that( I ) can be prepared in 50% yield in a two-stage nitration process.