Direct adaptive impedance control of robot manipulators

This article presents an adaptive scheme for controlling the end-effector impedance of robot manipulators. The proposed control system consists of three subsystems: a simple “filter” that characterizes the desired dynamic relationship between the end-effector position error and the end-effector/environment contact force, an adaptive controller that produces the Cartesian-space control input required to provide this desired dynamic relationship, and an algorithm for mapping the Cartesian-space control input to a physically realizable joint-space control torque. The controller does not require knowledge of either the structure or the parameter values of the robot dynamics and is implemented without calculation of the robot inverse kinematic transformation. As a result, the scheme represents a general and computationally efficient approach to controlling the impedance of both nonredundant and redundant manipulators. Furthermore, the method can be applied directly to trajectory tracking in free-space motion by removing the impedance filter. Computer simulation results are given for a planar four degree-of-freedom redundant robot under adaptive impedance control. These results demonstrate that accurate end-effector impedance control and effective redundancy utilization can be achieved simultaneously by using the proposed controller.     

Nonlinear robust adaptive Cartesian impedance control of UAVs equipped with a robot manipulator

In this paper, a new nonlinear robust adaptive impedance controller is addressed for Unmanned Aerial Vehicles (UAVs) equipped with a robot manipulator that physically interacts with environment. A UAV equipped with a robot manipulator is a novel system that can perform different tasks instead of human being in dangerous and/or inaccessible environments. The objective of the proposed robust adaptive controller is control of the UAV and its robotic manipulator’s end-effector impedance in Cartesian space in order to have a stable physical interaction with environment. The proposed controller is robust against parametric uncertainties in the nonlinear dynamics model of the UAV and the robot manipulator. Moreover, the controller has robustness against the bounded force sensor inaccuracies and bounded unstructured modeling (nonparametric) uncertainties and/or disturbances in the system. Tracking performance and stability of the system are proved via Lyapunov stability theorem. Using simulations on a quadrotor UAV equipped with a three-DOF robot manipulator, the effectiveness of the proposed robust adaptive impedance controller is investigated in the presence of the force sensor error, and parametric and non-parametric uncertainties.     

Adaptive explicit force control of position-controlled manipulators

This article presents a new adaptive outer-loop approach for explicit force regulation of position-controlled robot manipulators. The strategy is computationally simple and does not require knowledge of the manipulator dynamic model, the inner-loop position controller parameters, or the environment. It is shown that the control strategy guarantees global uniform boundedness of all signals and convergence of the position/force regulation errors to zero when applied to the full nonlinear robot dynamic model. If bounded external disturbances are present, a slight modification to the control scheme ensures that global uniform boundedness of all signals is retained and that arbitrarily accurate stabilization of the regulation errors can be achieved. Additionally, it is shown that the adaptive controller is also applicable to robotic systems with PID inner-loop position controllers. Computer simulation results are given for a Robotics Research Corporation (RRC) Model K-1207 redundant arm and demonstrate that accurate and robust force control is achievable with the proposed controller. Experimental results are presented for the RRC Model K-1207 robot and confirm that the control scheme provides a simple and effective means of obtaining high-performance force control. © 1996 John Wiley & Sons, Inc.     

Real-time implementation of a robust adaptive controller for arobotic manipulator based on digital signal processors

Presents an approach to the design and real-time implementation of an adaptive controller for a robotic manipulator based on digital signal processors. The Texas Instruments DSP (TMS320C31) chips are used in implementing real-time adaptive control algorithms to provide enhanced motion control performance for robotic manipulators. In the proposed scheme, adaptation laws are derived from the direct model reference adaptive control principle based on the improved Lyapunov second method. The proposed adaptive controller consists of an adaptive feedforward and feedback controller and PI-type time-varying auxiliary control elements. The proposed control scheme is simple in structure, fast in computation, and suitable for real-time control. Moreover, this scheme does not require any accurate dynamic modeling nor values of manipulator parameters and payload. Performance of the proposed adaptive controller is illustrated by simulation and experimental results for an industrial robot with four joints in the joint space and Cartesian space     

一种工业机器手的自适应阻抗控制方法

提出一种基于任务空间的直接自适应阻抗方法，它不要求辨识机器手动态模型结构和参数，不需要计算机器手的运动学逆变换，因此，避免了基于机器手模型线性参数辨识的控制方法的缺点。     

Direct adaptive control of manipulators in cartesian space

A new adaptive-control scheme for direct control of manipulator end effector to achieve trajectory tracking in Cartesian space is developed in this article. The control structure is obtained from linear multivariable theory and is composed of simple feedforward and feedback controllers and an auxiliary input. The direct adaptation laws are derived from model reference adaptive control theory and are not based on parameter estimation of the robot model. The utilization of adaptive feedforward control and the inclusion of auxiliary input are novel features of the present scheme and result in improved dynamic performance over existing adaptive control schemes. The adaptive controller does not require the complex mathematical model of the robot dynamics or any knowledge of the robot parameters or the payload, and is computationally fast for on-line implementation with high sampling rates. The control scheme is applied to a two-link manipulator for illustration.     

A Generalized Vision-based Stiffness Controller for Robot Manipulators with Bounded Inputs

Generally, stiffness and impedance control schemes require knowledge of the location of any object with which a robot interacts within its workspace; therefore, the integration of a computer vision system within the control loop allows us to know the location of the robot end effector and the object (target) simultaneously. In this paper, a generalized and saturating vision-based stiffness controller with adaptive gravity compensation is presented. The proposed control algorithm is designed to regulate robot-environment interaction in task-space, where the contact force is modeled as a vector of generalized bounded spring-like forces. In order to control nonredundant robots, the proposed controller has a nonlinear proportional-derivative structure with static model-based compensation of gravitational forces, as it includes a regressor-based adaptive term. To support the proposal, the Lyapunov stability analysis of the closed-loop equilibrium vector is presented. Finally, the suitable performance of the proposed scheme was verified by numerical simulations and experimental tests.

     

Toward the intelligent control of robots

A new adaptive control architecture for the intelligent control of robotic manipulators is developed. The design is capable of utilizing external sensory information for the robot control. To achieve this, first a model reference adaptive control (MRAC) is developed which can be applied to a robot arm in the task space. Then the concept of virtual adaptive model is defined, which is used to formulate a maneuvering strategy in response to the external information. Finally, the virtual model provides the modified reference signals to the MRAC system to control the corresponding modified motion of the robot in the environment. The design does not require any knowledge about the dynamic parameters of the robot or that of the environment.     

The dexterity and singularities of an underactuated robot

Underactuated robots are robotic systems with more joints than actuators. A robot may be underactuated by design as in the case of a hyper‐redundant robot with passive joints or may become underactuated as a result of an actuator failure. In this article, we examine the dexterity of underactuated robots whose passive joints operate in either a locked or free‐swinging mode. The ability to an analyze the dexterity of an underactuated robot has important applications especially for the control of passive joints with brakes and for the fault tolerance analysis of an otherwise fully actuated kinematically redundant robot. The approach applied here is to use kinematics and dynamics‐based formulations of manipulator dexterity. We then characterize passive‐joint singularities, i.e., configurations where full end‐effector control is lost because one or more joints are passive instead of active. Lastly, we introduce a new characterization of joint‐limit singularities, which are configurations where full end‐effector control cannot be achieved because one or more joints are at their joint limits. © 2001 John Wiley & Sons, Inc.     

Reconfigurable Control Structure for Robots in Assembly

The increased use of changeable characteristics in modern manufacturing and robotic systems and applications call for improved system control design that offers some degree of reconfigurability. The need for control reconfiguration of robotic systems arises due to some inherent characteristics of the robotic system, variations of robot parameters due to environmental changes, major task changes typical in production changeover or manufacturing system reconfiguration, or geometry changes due to the reconfiguration of modular manipulators. In this paper, a reconfigurable controller, the Supervisory Control Switching System (SCSS), is proposed to meet the new on-line demands for changeability in robotic systems. The SCSS is capable of selecting the most suitable controller for a particular task or situation, from separate controllers designed a priori. The applicability and effectiveness of the developed switching control scheme have been illustrated through computer simulations of an AdeptOne SCARA manipulators carrying out assembly tasks.     

Robot perception of impedance

This paper proposes an algorithm for robot perception of impedance, which can be used as a fundamental technique for real‐time and qualitative perception of physical constraints imposed on the robot's end‐effector. This algorithm (1) estimates the impedance that represents the motion‐force relation of the end‐effector; (2) calculates the uncertainties of the estimates; and (3) detects discontinuous changes in the impedance. The estimated impedance can be used to recognize local dynamic properties of the environment and temporary constraint conditions imposed on the end‐effector. The detected discontinuities can be used to segment the manipulated tasks and to recognize the geometric structure of the environment. This method can be implemented in both autonomous and remote‐controlled robots because it is designed separately from control methodologies. Results of preliminary experiments are presented. © 2005 Wiley Periodicals, Inc.     

An Adaptive Regulator of Robotic Manipulators in the Task Space

This note addresses the problem of position control of robotic manipulators both nonredundant and redundant in the task space. A computationally simple class of task space regulators consisting of a transpose adaptive Jacobian controller plus an adaptive term estimating generalized gravity forces is proposed. The Lyapunov stability theory is used to derive the control scheme. The conditions on controller gains ensuring asymptotic stability are obtained herein in a form of simple inequalities including some information extracted from both robot kinematic and dynamic equations. The performance of the proposed control strategy is illustrated through computer simulations for a direct-drive arm of a SCARA type redundant manipulator with the three revolute kinematic pairs operating in a two-dimensional task space.     

On controlling robots with redundancy

Recently there has been considerable interest in increasing the applicability and utility of robots by developing manipulators which possess kinematic and/or actuator redundancy. This paper presents a unified approach to controlling these redundant robots. The proposed control system consists of two subsystems: an adaptive position controller which generates the Cartesian-space control force FR^m required to track the desired end-effector position trajectory, and an algorithm that maps this control input to a robot joint torque vector TRⁿ. The F → T map is constructed so that the robot redundancy (kinematic and/or actuator) is utilized to improve the performance of the robot. The control scheme does not require knowledge of the complex robot dynamic model or parameter values for the robot or the payload. As a result, the controller is very general and is computationally efficient for on-line implementation. Computer simulation results are given for a kinematically redundant robot, for a robot with actuator redundancy, and for a robot which possesses both kinematic and actuator redundancy. In each case the results demonstrate that accurate end-effector trajectory tracking and effective redundancy utilization can be achieved simultaneously with the proposed scheme.     

Automation of surface finishing processes

The development of robots capable of interacting dynamically with the environment has proven to be a difficult task. Since a majority of manufacturing tasks require interaction of robots with their environment, this has become an important focus for research in the industry. Solutions both to specific manufacturing operations and to the theoretical body of knowledge within the industry are extremely important. The interaction of the robot with its environment is investigated in this paper for the configuration of a quick actuator and sensor attached to the robot tool. This configuration has been tested in an industrial application for Steinway & Sons, the world renowned piano manufacturer, specifically for the automation of the labor-intensive rubbing and finishing operations. The robot architecture utilizes a combination of macro-micro manipulator to improve its response time. A quick actuator added to the end of the robot arm is the micromanipulator, and the robot arm is the macromanipulator. Force and impedance control laws are executed concurrently by two separate controllers to control the quick actuator and the robot arm respectively. The experimental system proves the ability of this configuration to follow the complex contour of a grand piano rim and to exert a given force while rubbing its surface.     

Adaptive control of redundant multiple robots in cooperative motion

A redundant robot has more degrees of freedom than what is needed to uniquely position the robot end-effector. In practical applications the extra degrees of freedom increase the orientation and reach of the robot. Also the load carrying capacity of a single robot can be increased by cooperative manipulation of the load by two or more robots. In this paper, we develop an adaptive control scheme for kinematically redundant multiple robots in cooperative motion.In a usual robotic task, only the end-effector position trajectory is specified. The joint position trajectory will therefore be unknown for a redundant multi-robot system and it must be selected from a self-motion manifold for a specified end-effector or load motion. In this paper, it is shown that the adaptive control of cooperative multiple redundant robots can be addressed as a reference velocity tracking problem in the joint space. A stable adaptive velocity control law is derived. This controller ensures the bounded estimation of the unknown dynamic parameters of the robots and the load, the exponential convergence to zero of the velocity tracking errors, and the boundedness of the internal forces. The individual robot joint motions are shown to be stable by decomposing the joint coordinates into two variables, one which is homeomorphic to the load coordinates, the other to the coordinates of the self-motion manifold. The dynamics on the self-motion manifold are directly shown to be related to the concept of zero-dynamics. It is shown that if the reference joint trajectory is selected to optimize a certain type of objective functions, then stable dynamics on the self-motion manifold result. The overall stability of the joint positions is established from the stability of two cascaded dynamic systems involving the two decomposed coordinates.     

基于无模型自适应的外骨骼式上肢康复机器人主动交互训练控制方法

设计了一种基于无模型自适应的外骨骼式上肢康复机器人主动交互训练控制方法.在机器人与人体上肢接触面安装力传感器采集人机交互力矩信息作为量化的主动运动意图,设计了一种无模型自适应滤波算法使交互力矩变得平滑而连贯;以人机交互力矩为输入,综合考虑机器人末端点与参考轨迹的相对位置和补偿力的信息,设计了人机交互阻抗控制器,用于调节各关节的给定目标速度;设计了将无模型自适应与离散滑模趋近律相结合的速度控制器完成机器人各关节对目标速度的跟踪.仿真结果表明,该控制方法可以实现外骨骼式上肢康复机器人辅助患者完成主动交互训练的功能.通过调节人机交互阻抗控制器的相应参数,机器人可以按照患者的运动意图完成不同的主动交互训练任务,并在运动出现偏差时予以矫正.控制器在设计实现过程中不要求复杂准确的动力学建模和参数识别,并有一定的抗干扰性和通用性.     

Adaptive force and position control of manipulators

The article presents simple methods for the design of adaptive force and position controllers for robot manipulators within the hybrid control architecture. The force controller is composed of an adaptive PID feedback controller, an auxiliary signal, and a force feedforward term, and achieves tracking of desired force setpoints in the constraint directions. The position controller consists of adaptive feedback and feedforward controllers as well as an auxiliary signal, and accomplishes tracking of desired position trajectories in the free directions. The controllers are capable of compensating for dynamic cross-couplings that exist between the position and force control loops in the hybrid control architecture. The adaptive controllers do not require knowledge of the complex dynamic model or parameter values of the manipulator or the environment. The proposed control schemes are computationally fast and suitable for implementation in online control with high sampling rates. The methods are applied to a two-link manipulator for simultaneous force and position control. Simulation results confirm that the adaptive controllers perform remarkably well under different conditions.     

Locomotion Control of a Hydraulically Actuated Hexapod Robot by Robust Adaptive Fuzzy Control with Self-Tuned Adaptation Gain and Dead Zone Fuzzy Pre-compensation

Hydraulically actuated robotic mechanisms are becoming popular for field robotic applications for their compact design and large output power. However, they exhibit nonlinearity, parameter variation and flattery delay in the response. This flattery delay, which often causes poor trajectory tracking performance of the robot, is possibly caused by the dead zone of the proportional electromagnetic control valves and the delay associated with oil flow. In this investigation, we have proposed a trajectory tracking control system for hydraulically actuated robotic mechanism that diminishes the flattery delay in the output response. The proposed controller consists of a robust adaptive fuzzy controller with self-tuned adaptation gain in the feedback loop to cope with the parameter variation and disturbances and a one-step-ahead fuzzy controller in the feed-forward loop for hydraulic dead zone pre-compensation. The adaptation law of the feedback controller has been designed by Lyapunov synthesis method and its adaptation rate is varied by fuzzy self-tuning. The variable adaptation rate helps to improve the tracking performance without sacrificing the stability. The proposed control technique has been applied for locomotion control of a hydraulically actuated hexapod robot under independent joint control framework. For tracking performance of the proposed controller has also been compared with classical PID controller, LQG state feedback controller and static fuzzy controller. The experimental results exhibit a very accurate foot trajectory tracking with very small tracking error with the proposed controller.     

Fusion Strategies for Minimizing Sensing-Level Uncertainty in Manipulator Control

Humanoid robotic applications require robot to act and behave like human being. Following soft computing like approach human being can think, decide and control himself in unstructured dynamic surroundings, where a great degree of uncertainty exists in the information obtained through sensory organs. In the robotics domain also, one of the key issues in extracting useful knowledge from sensory data is that of coping with information as well as sensory uncertainty at various levels. In this paper a generalized fusion based hybrid classifier (ANN-FDD-FFA) has been developed and applied for validating on generated synthetic data from observation model as well as from real hardware robot. The fusion goal, selected here, is primarily to minimize uncertainties in robotic manipulation tasks that are based on internal (joint sensors) as well as external (vision camera) sensory information. The effectiveness of present methodology has been extensively studied with a specially configured experimental robot having five degrees of freedom and a simulated model of a vision guided manipulator. In the present investigation main uncertainty handling approach includes weighted parameter selection (of geometric fusion) by a trained neural network that is not available in standard manipulator robotic controller designs. These approaches in hybrid configuration has significantly reduce the uncertainty at different levels for faster and more accurate manipulator control as demonstrated here through rigorous simulations and experimentations.     

A Learning Behavior Based Controller for Maintaining Balance in Robotic Locomotion

The Behavior Based Locomotion Controller (BBLC) extends the applicability of the behavior based control (BBC) architecture to redundant systems with multiple task-space motions. A set of control behaviors are attributed to each task-space motion individually and a reinforcement learning algorithm is used to select the combination of behaviors which can achieve the control objective. The resulting behavior combination is an emergent control behavior robust to unknown environments due to the added learning capability. Hence, the BBLC is applicable to complex redundant systems operating in unknown environments, where the emergent control behaviors can satisfy higher level control objectives such as balance in locomotion. The balance control problem of two robotic systems, a bipedal robot walker and a mobile manipulator, are used to study the performance of this controller. Results show that the BBLC strategy can generate emergent balancing strategies capable of adapting to new unknown disturbances from the environment, using only a small fixed library of balancing behaviors.