Blending of polystyrene with styrene-siloxane block and graft copolymers

A preliminary study on the efficiency of styrene-siloxane block and graft copolymer as toughening additives for polystyrene has been made. Block and graft copolymers of required molecular weight were synthesized for making compatible blends with polystyrene. Compatibility of these systems was evaluated through differential scanning calorimetry, thermo-mechanical analysis, rheovibron studies, and scanning electron microscopy. A good miscibility of block and graft copolymers was confirmed by these methods. Higher work of rupture in these blended polystyrene samples further demonstrates the feasibility of styrene-siloxane block and graft copolymers as good toughening material for a brittle polystyrene matrix. The mechanical properties have been related to the morphology and the amount of siloxane content in the blended polystyrene.     

Role of block copolymer on the coarsening of morphology in polymer blend: Effect of micelles

The reactive compatibilization of polystyrene/ethylene‐α‐octene copolymer (PS/POE) blend via Friedel–Crafts alkylation reaction was investigated by rheology and electron microscope. It was found that the graft copolymer formed from interfacial reaction reduced the domain size and decreased the coarsening rate of morphology. The reduction of the interfacial tension is very limited according to the mean field theory even assuming that all block copolymer stays on the interface. With the help of self‐consistent field theory and rheological constitutive models, the distribution of graft copolymer was successfully estimated. It was found that large amount of copolymer had detached from the interfaces and formed micelles in the matrix. Both the block copolymer micelles in matrix and the block copolymers at the interface contribute to the suppression of coarsening in polymer blend, but play their roles at different stages of droplet coalescence. In droplet morphology, the micelles mainly hinder the approaching of droplets. © 2014 American Institute of Chemical Engineers AIChE J, 61: 285–295, 2015     

Phase morphology and melt rheological behavior of uncrosslinked and dynamically crosslinked polyolefin blends: role of macromolecular structure

Thermoplastic vulcanizates (TPVs) based on polypropylene (PP) with ethylene–octene copolymer (EOC) and ethylene propylene diene rubber (EPDM) have been prepared by co-agent-assisted peroxide crosslinking system. The study was pursued to explore the influence of two dissimilar polyolefin polymers having different molecular architecture on the state and mode of dispersion of the blend components and their influence on melt rheological properties. The effects of dynamic crosslinking of the PP/EOC and PP/EPDM have been compared with special reference to the concentration of crosslinking agent and ratio of blend components. Morphological analyses show that, irrespective of blend ratio, dynamic vulcanization exhibits a dispersed phase morphology with crosslinked EOC or EPDM particles in the continuous PP matrix. It was found that viscosity ratio plays a crucial role in determining the state and mode of dispersion of blend components in the uncrosslinked system. The lower viscosity and torque values of uncrosslinked and dynamically crosslinked blends of PP/EOC in the melt state indicates that they exhibit better processing characteristics when compared to corresponding PP/EPDM blends.     

Morphology and micromechanical behavior of binary blends comprising block copolymers having different architectures

Morphology and deformation behavior of binary blends comprising styrene/butadiene block copolymers (polystyrene content, Φ_PS∼0.70) having different molecular architectures were studied by means of transmission electron microscopy and tensile testing. In contrast to the binary diblock copolymer blends discussed in literature, the phase separation behavior of the blends investigated was found to be strongly affected by asymmetric molecular architecture. The blends showed macrophase separated grains, in which the structures resembled the microphase morphology of none of the blend components. Unlike the classical rubber-modified or particle-filled thermoplastics, neither debonding at the particle/matrix interface nor the particle cavitation was observed in these nanostructured blends. The microdeformation of the blends revealed plastic drawing of polystyrene lamellae or PS struts dispersed in rubbery matrix and orientation of the whole deformation structures along the strain direction.     

Blends of poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 toughened by maleated polystyrene‐based copolymers: Mechanical properties,morphology, and rheology

Poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 (PPO/PA6 30/70) blends were impact modified by addition of three kinds of maleated polystyrene‐based copolymers, i.e., maleated styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA), maleated methyl methacrylate‐butadiene‐styrene copolymer (MBS‐g‐MA), and maleated acrylonitrile‐butadiene‐styrene copolymer (ABS‐g‐MA). The mechanical properties, morphology and rheological behavior of the impact modified PPO/PA6 blends were investigated. The selective location of the maleated copolymers in one phase or at interface accounted for the different toughening effects of the maleated copolymer, which is closely related to their molecular structure and composition. SEBS‐g‐MA was uniformly dispersed in PPO phase and greatly toughened PPO/PA6 blends even at low temperature. MBS‐g‐MA particles were mainly dispersed in the PA6 phase and around the PPO phase, resulting in a significant enhancement of the notched Izod impact strength of PPO/PA6 blends from 45 J/m to 281 J/m at the MBS‐g‐MA content of 20 phr. In comparison, the ABS‐g‐MA was mainly dispersed in PA6 phase without much influencing the original mechanical properties of the PPO/PA6 blend. The different molecule structure and selective location of the maleated copolymers in the blends were reflected by the change of rheological behavior as well. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of the molecular structure of ethene–propene and styrene–butadiene copolymers on their compatibilization efficiency in low‐density polyethylene/polystyrene blends

The effect of the molecular structure of styrene–butadiene (SB) block copolymers and ethene–propene (EPM) random copolymers on the morphology and tensile impact strength of low‐density polyethylene (LDPE)/polystyrene (PS) (75/25) blends has been studied. The molecular characteristics of SB block copolymers markedly influence their distribution in LDPE/PS blends. In all cases, an SB copolymer is present not only at the interface but also in the bulk phases; this depends on its molecular structure. In blends compatibilized with diblock copolymers, compartmentalized PS particles can also be observed. The highest toughness values have been achieved for blends compatibilized with triblock SB copolymers. A study of the compatibilization efficiency of SB copolymers with the same number of blocks has shown that copolymers with shorter PS blocks are more efficient. A comparison of the obtained results with previous results indicates that the compatibilization efficiency of a copolymer strongly depends both on the blend composition and on the properties of the components. The compatibilization efficiency of an EPM/SB mixture is markedly affected by the rheological properties of the copolymers. The addition of an EPM/SB mixture containing EPM with a higher viscosity leads to a higher improvement or at least the same improvement in the tensile impact strength of a compatibilized blend as the same amount of neat SB. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Rheology,morphology, and mechanical properties of reactive compatibilized polypropylene/polystyrene blends via Friedel–Crafts alkylation reaction in the presence of clay

Attempts were made to study the effect of reactive compatibilization via Friedel–Crafts alkylation reaction, using AlCl₃ as a catalyst, on rheology, morphology, and mechanical properties of polypropylene/polystyrene ( PP/PS) blends in the presence of an organoclay (Cloisite 15A). During the reactive compatibilization process, PS showed much more degradation than that of PP in the presence of AlCl₃. It was found that the effect of generation of PP‐g‐PS copolymer at the interface of the PP/PS blend dominates the effects of degradation of PS and PP phases, which manifested itself by increased toughness as well as uniform dispersion of the dispersed PS particles in the PP matrix. Generation of PP‐g‐PS copolymer was confirmed by using Fourier‐transform infrared analysis. By using rheological and X‐ray diffraction analyses, it was shown that the clay had higher affinity to PS than that of PP. It was also shown that the clay located at the interface of PP and PS phases, leading to increased relaxation time of the deformed PS dispersed particles, exhibited higher dispersion in PP/PS blend, which resulted in higher ductility of the blend. By using the results of rheological studies, it was concluded that during reactive compatibilization of the blend nanocomposite, the clay migrated into the dispersed PS phase, which was confirmed by scanning electron microscopy analysis. It was demonstrated that the rheological studies have a reliable sensitivity to the clay partitioning and phase morphology of the studied blends and blend nanocomposites . J. VINYL ADDIT. TECHNOL., 24:18–26, 2018. © 2015 Society of Plastics Engineers     

Effects of Polystyrene Block Content on Morphology and Adhesion Property of Polystyrene Block Copolymer

Effects of polystyrene block content on adhesion property and phase structure of polystyrene block copolymers were investigated. Polystyrene-block-polyisoprene-block-polystyrene triblock and polystyrene-block-polyisoprene diblock copolymers with different polystyrene block contents in the range from 13 to 35 wt% were used. In the case of the low polystyrene block content (below 16 wt%), a sea-island structure was observed: near-spherical polystyrene domains having a mean diameter of about 20 nm were dispersed in polyisoprene matrix. The phase structure changed from a sea-island structure to a cylindrical structure with an increase of polystyrene block content (over 18 wt%). Peel strength decreased with an increase of polystyrene block content and the pure triblock copolymers had lower peel strength than their blends with the diblock copolymers. Pulse nuclear magnetic resonance studies indicated that molecular mobility of polyisoprene phase decreased with an increase of polystyrene block content, and the molecular mobility was lower in the pure triblock than in the blend. Thus, the peel strength was found to be related to molecular mobility. The adhesion strength of the block copolymer depended on the molecular mobility: high molecular mobility can promote interfacial adhesion.     

Controllable Synthesis of Submicrometer Core–Shell Modifier and Its Effect on Toughening Polypheylene Ether/Polystyrene Blends

Core–shell polybutadiene-graft-polystyrene (PB-g-PS) graft copolymers with different ratios of PB to PS are synthesized by emulsion polymerization. Further, the PB-g-PS copolymers are blended with polypheylene ether (PPE) and PS to prepare PPE/PS/PB-g-PS blends. The effects of PB-g-PS copolymer structure and matrix composition on the morphological, mechanical properties, and deformation mechanism of the blends are studied. The results show that the synthesized submicrometer-sized PB-g-PS copolymer has an excellent toughening efficiency, both the copolymer and PS are introduced into PPE resin to produce a ternary blend which is combined with high toughness and processing properties. The optimum toughening effect on PPE/PS matrix is observed at the core–shell weight ratio of 70/30 in PB-g-PS copolymer, and the impact strength of the blends increased from 101 to 550 J m⁻¹. In addition, the dispersion pattern of rubber particles in the matrix gradually changes from uniform dispersion to aggregation as the core–shell ratio of PB-g-PS copolymers increases. On the other hand, with the increase of PPE content, the dispersion of rubber particles in PPE/PS matrix is improved, and the deformation mechanism is changed from cracking to a combination of crazing and shear yielding, which can lead to absorb more energy to achieve better toughness.     

Deformation behavior of HDPE/(PEC/PS)/SEBS blends

Immiscible blends of high density polyethylene (HDPE) and an amorphous glassy phase consisting of either pure polystyrene (PS) or a miscible blend of PS and a polyether copolymer (PEC) were compatibilized with various amounts of a styrene-hydrogenated butadiene block copolymer (SEBS). PEC is structurally similar to poly(2,6-dimethyl-1,4-phenylene oxide) (PPO). Using a liquid displacement stress dilatometer, the volume change of samples during uniaxial mechanical straining was determined and related to the various modes of deformation. Blends were fabricated by both injection and compression molding. Miscible PEC and PS blends were found to undergo a craze to shear yielding transition between 40 and 60% PS, which occurred at higher PS concentrations as SEBS was added. Blends with a HDPE matrix and a dispersed glassy phase showed reduced volume dilatation on adding SEBS, indicating better interfacial adhesion between the incompatible blend components. Increases in the sample volume were substantially less in blends with a PEC/PS glassy phase instead of pure PS, suggesting more effective compatibilization by the SEBS copolymer in blends with PEC. This trend is presumed to stem from an exothermic heat of mixing between the PS endblocks of SEBS and the PEC-rich phases in the blend. Microscopic evidence of the improved adhesion and modes of deformation agrees with the results obtained by dilatometry. The volume dilatation of compression-molded materials do not seem to be similarly affected by the composition of the glassy phase which may reflect morphological differences between injection-and compression-molded blends.     

Morphology of HDPE/(PEC/PS) blends modified with SEBS copolymers

In this study, immiscible blends of HDPE and an amorphous glassy polymer were compatibilized with styrene-hydrogenated butadiene block copolymers. The glassy phase consisted of either pure PS or a miscible blend of PS and polyether copolymer (PEC); PEC is similar to poly(2,6-dimethyl-1,4-phenylene oxide) (PPO). The morphology of these two-phase mixtures depended on physical characteristics of the components and the method of fabrication. Suitable copolymers increased the degree of dispersion and minimized heterogeneities resulting from the inherent incompatibility of the individual phases. Further reduction in the phase size and increased adhesion between the components of modified blends were achieved by increasing the composition of PEC in the glassy phase. It was concluded that favorable exothermic mixing between PEC and PS endblocks of the copolymers provided an additional driving force for compatibilization. Results from dynamic mechanical thermal analysis suggests that penetration by the copolymers into the homopolymer phases is not complete.     

Optical properties of polystyrene and polyarylate block copolymer and their control by morphology generation

Relationship between phase morphology and optical properties of polystyrene and polyarylate (PS‐PAr) block copolymers synthesized from telechelic polystyrene has been investigated. In the PS‐PAr block copolymers, the PAr domains with higher melt viscosity were dispersed in the PS phase matrix with lower melt viscosity over the wide range of their composition from PS/PAr = 25/75 to 75/25 (wt ratio). The PAr domain size was dependent on the reactive ratio of PAr determined analogously by the mole fraction of the fed telechelic polystyrene. By controlling the mole fraction of the telechelic polystyrene more than 0.016 in synthesizing the PS‐PAr block copolymer, the size of PAr domains could be reduced to the microscopic scale (smaller than 100 nm). Then, the PS‐PAr block copolymers exhibited almost the same transparency as PAr in spite of the large difference in the refractive index between the PS and the PAr phase. Birefringence free condition for the PS‐PAr block copolymers was determined by not only the PS/PAr composition but also the balance in the degree of molecular orientation of these chains. The latter factor suggests that PS and PAr chains undergo inhomogeneous stress and relaxation history during the injection process. By controlling Mn (number average molecular weight) and weight fraction of the fed OH‐PS‐OH around 20 000 and 55 wt %, respectively, in the synthesis of the PS‐PAr block copolymer, the PS‐PAr block copolymer exhibited almost zero birefringence without any sacrifice of transparency. Because in the PS‐PAr block copolymer low birefringence and high transparency can coexist by controlling the adequate feeding condition in the synthesis process, the PS‐PAr block copolymer would be a promising material for optical applications, such as a substrate of optical disks or optical lenses. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 953–961, 2000     

Viscoelastic properties of a styrene-isoprene-styrene triblock copolymer and its blends with polyisoprene homopolymer and styrene-isoprene diblock copolymer

The effects of added polyisoprene homopolymer (PI) and polyisoprene-blockstyrene diblock copolymer (SI) on the viscoelastic properties of a polystyrene-block-polyisoprene-block-polystyrene triblock copolymer (SIS) having a spherical domain morphology have been examined. The former two species are used to model the effects of imperfections in structures that result from triblock copolymers missing, respectively, two or one polystyrene end blocks. The results indicate that the loss modulus and tangent delta in the plateau region can be dominated by imperfections in the copolymer structure. The interpretation of viscoelastic data in the rubbery plateau region as an indication of interface structure in block copolymers is therefore greatly complicated. Small angle X-ray scattering (SAXS) and rheological tests were also used to determine the order-disorder transition temperature for an SIS triblock copolymer and its blend with an SI diblock. The SAXS data are consistent with Han's rheological criteria for determining the order-disorder transition temperature. However, the complex viscosity does exhibit Newtonian behavior for low rates at the highest temperatures, even though the domain morphology persists. Stress relaxation and dynamic modulus data at high temperatures clearly show a secondary “rubbery” plateau at long times, and we offer a qualitative explanation for this feature based on a proposed relaxation mechanism.     

Compatibilization effects of styrenic/rubber block copolymers in polypropylene/polystyrene blends

Compatibilizing effects of styrene/rubber block copolymers poly(styrene‐b‐butadiene‐b‐styrene) (SBS), poly(styrene‐b‐ethylene‐co‐propylene) (SEP), and two types of poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) (SEBS), which differ in their molecular weights on morphology and selected mechanical properties of immiscible polypropylene/polystyrene (PP/PS) 70/30 blend were investigated. Three different concentrations of styrene/rubber block copolymers were used (2.5, 5, and 10 wt %). Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to examine the phase morphology of blends. The SEM analysis revealed that the size of the dispersed particles decreases as the content of the compatibilizer increases. Reduction of the dispersed particles sizes of blends compatibilized with SEP, SBS, and low‐molecular weight SEBS agrees well with the theoretical predictions based on interaction energy densities determined by the binary interaction model of Paul and Barlow. The SEM analysis confirmed improved interfacial adhesion between matrix and dispersed phase. The TEM micrographs showed that SBS, SEP, and low‐molecular weight SEBS enveloped and joined pure PS particles into complex dispersed aggregates. Bimodal particle size distribution was observed in the case of SEP and low‐molecular weight SEBS addition. Notched impact strength (a_k), elongation at yield (ε_y), and Young's modulus (E) were measured as a function of weight percent of different types of styrene/rubber block copolymers. The a_k and ε_y were improved whereas E gradually decreased with increasing amount of the compatibilizer. The a_k was improved significantly by the addition of SEP. It was found that the compatibilizing efficiency of block copolymer used is strongly dependent on the chemical structure of rubber block, molecular weight of block copolymer molecule, and its concentration. The SEP diblock copolymer proved to be a superior compatibilizer over SBS and SEBS triblock copolymers. Low‐molecular weight SEBS appeared to be a more efficient compatibilizer in PP/PS blend than high‐molecular weight SEBS. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 291–307, 1999     

Bio‐based diblock copolymers prepared from poly(lactic acid) and natural rubber

New bio‐based diblock copolymers were synthesized from poly(lactic acid) (PLA) and natural rubber (NR). NR polymer chains were modified to obtain hydroxyl telechelic natural rubber oligomers (HTNR). Condensation polymerization between PLA and HTNR was performed at 110°C during 24 or 48 h. The molecular weight of PLA and HTNR and the molar ratio PLA : HTNR were varied. The new ester linkage in the diblock copolymers was determined by ¹H‐NMR. The molecular weight of the diblock copolymers determined from SEC agreed with that expected from calculation. The thermal behavior and degradation temperature were determined by DSC and TGA, respectively. The diblock copolymers were used as a toughening agent of PLA and as a compatibilizer of the PLA/NR blend. PLA blended with the diblock copolymer showed higher impact strength, which was comparable to the one of a PLA/NR blend. The former blend showed smaller dispersed particles as showed by SEM images, indicating the increase in miscibility in the blend due to the PLA block. The compatibilization was effective in the blends containing ～10 wt % of rubber. At a higher rubber content (>10 wt %), coalescence of the NR and diblock copolymer was responsible of the larger rubber diameter in the blends, which causes a decrease of the impact strength. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41426.     

Rheological characterization of polypropylene/poly(ethylene-<Emphasis Type="Italic">co</Emphasis>-propylene) in-reactor blends synthesized under different polymerization conditions

In-reactor blends of polypropylene/poly(ethylene-co-propylene) with complex microstructure, synthesized through different polymerization procedures; two-step (one homopolymerization and one copolymerization under high ethylene concentration) and three-step (with an additional copolymerization step under low ethylene concentration), were characterized by rheological measurements. The effects of a change in the polymerization process on the types and amounts of block copolymers in the blends were evaluated using small amplitude oscillation rheometry in the linear viscoelastic region. The Palierne model in its complete form was employed to model the rheological behavior of the blends. For this analysis the reactor products were separated into xylene cold insoluble (XCI) and xylene cold soluble fractions. Besides, another two copolymer fractions at 80 and 100 °C, which are crystallizable copolymer fractions and contain block copolymers rich in polyethylene and polypropylene, respectively, were separated from XCI fraction by xylene using temperature gradient elution fractionation method. Considering all copolymer fractions as dispersed and the remained fraction (mostly polypropylene) as matrix phase, it was shown that the rheological properties of the blends could not be predicted by Palierne model. It was found that only by considering part of block copolymer fractions having long polypropylene sequences along with polypropylene homopolymer as one phase, the rheological properties of the blends could be predicted by Palierne model. By rheological modeling, it was confirmed that the amounts of copolymers with long polypropylene sequences which are miscible with the matrix are higher in the case of three-step blends and also the elasticity of three-step polymerized blends is higher than two-step polymerized blends.     

Correlation of viscosity ratio,morphology, and mechanical properties of polyamide 12/natural rubber blends via reactive compatibilization

Natural rubber (NR)-modified polyamide 12 (Nylon12/NR) was produced by melt blending Nylon12 and NR in the presence of polystyrene/maleated natural rubber (PS/MNR) copolymer as a reactive compatibilizer. The influence of compatibilizer loading on viscosity ratio, morphology, and mechanical properties of the blends was investigated. As a consequence of the reactive blend between Nylon12 and maleated NR in PS/MNR, the formation of amide and succinimide linkages was set at rubber-Nylon12 interfaces. Thus the dispersion of rubber particles was improved, and the particle coalescence was prevented so that the fine morphology with good interfacial adhesion was stabilized. This also resulted to enhance the blend viscosity and to lower viscosity ratio. The data revealed strong correlation between low viscosity ratio and fine spherical morphology of the compatibilized blends. An optimum PS/MNR compatibilizer content was at 7 phr to produce good dispersion of small rubber domains (size ≤0.3 μm) in Nylon12 matrix. Thermal properties by DSC revealed that crystallization temperature of Nylon12 was lowered by the presence of NR and crystallinity of Nylon12 was slightly affected by the PS/MNR content. An enhancement of mechanical properties, especially the impact energy was observed without suffering the tensile and flexural properties. Compared to the neat Nylon12, the compatibilized blends showed an increase in impact energy by a factor of 5. This large enhancement is successfully interpreted in term of the toughening effect by rubber phase of suitable dispersed size and the interparticle distance.     

Relationship among microstructure, linear viscoelastic behavior and mechanical properties of SBS triblock copolymer-compatibilized PP/SAN blend

Morphological, rheological and mechanical properties of the polypropylene (PP) and poly(styrene-co-acrylonitrile) (SAN) blend containing poly(styrene-b-butadiene-b-styrene) (SBS) triblock copolymer (ranging from 0 to 20 wt%) were studied by scanning electron microscopy (SEM), small amplitude oscillatory shear analysis, and both tensile and impact tests, respectively. SEM observations showed that SBS reduced the diameter of the SAN dispersed particles as well as improved the adhesion between the matrix and the dispersed phase. Close examination of SEM micrographs further revealed that the dispersed phase domains were complex aggregates of SAN particles enveloped and joined together with the SBS compatibilizer in the PP matrix. The variation of the dynamic rheological parameters, including dynamic moduli (G′ and G″), complex viscosity ( $ \eta^{ * } $ ), loss factor (tan δ), together with Cole–Cole diagrams, with blend composition particularly at low frequency regions were determined to evaluate the interfacial activity of SBS copolymer. A specific viscoelastic phenomenon, i.e., “the second plateau”, appeared at low frequencies for PP/SAN blend containing 20 wt% of SBS and exhibited a certain dependence on the SBS amount and dispersion state in the matrix. This phenomenon was attributed to the formation of aggregate structure between SAN particles and SBS triblock copolymer. Finally, the results of uniaxial tensile and Charpy impact tests conducted on both unnotched and notched specimens indicated that in PP/SAN blend, SBS functions as both compatibilizer and toughening agent.     

Effect of center block structure on the physical and rheological properties of ABA block copolymers. Part II. Rheological properties

The effect of the chemical structure of the center block on the rheological properties of ABA block copolymers with polystyrene end blocks has been investigated. The chemical structure of the center blocks investigated in the present paper are polybutadiene, polyisoprene, ethylene/butene copolymer, ethylene/propylene copolymer and polydimethyl-siloxane. The chemical structure of the center block was found to have a pronounced effect on the rheological properties of the ABA block copolymer melts. The long range relaxation times of these block copolymer melts increases with increasing incompatibility between the styrene block and the center block. However, the rheological properties of the block copolymers are not influenced significantly by the glass transition or the entanglement molecular weight of the center block.     

Deformation and alignment of lamellae in melt extension of blends of a styrene‐butadiene block copolymer with polystyrene

The development of the morphology and the alignment of lamellae in melt elongation of blends of an asymmetric linear styrene‐butadiene block copolymer (LN3) and polystyrene (PS 158K) was investigated. PS 158K and LN3 formed two‐phase polymer blends with PS 158K resp. LN3 inclusions, depending on the concentration of polystyrene. The block copolymer was arranged in a lamellar phase with a lamellae thickness of ～ 13 nm. Our rheological experiments revealed that the complex modulus, the elongational viscosity and the recovered stretch of the blends primarily resulted from a superposition of the properties of the blend components. In melt elongation, pure LN3 started to crumple at a small Hencky strain. In the blends, the presence of the PS 158K inclusions led to a macroscopically more uniform elongation, but with an anisotropic Poisson ratio. The LN3 inclusions in the PS 158K matrix were deformed into a filament‐like shape. In the blends with a LN3 matrix the alignment of the block copolymer lamellae parallel to the loading direction increased with applied extensional strain. In the latter case, the lamellae thickness did not decrease significantly. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009