Investigating the effect of porosity level and pore former type on the mechanical and corrosion resistance properties of agro-waste shaped porous alumina ceramics

The strength integrity and chemical stability of porous alumina ceramics operating under extreme service conditions are of major importance in understanding their service behavior if they are to stand the test of time. In the present study, the effect of porosity and different pore former type on the mechanical strength and corrosion resistance properties of porous alumina ceramics have been studied. Given the potential of agricultural wastes as pore-forming agents (PFAs), a series of porous alumina ceramics (Al₂O₃-xPFA; x=5, 10, 15 and 20 wt%) were successfully prepared from rice husk (RH) and sugarcane bagasse (SCB) through the powder metallurgy technique. Experimental results showed that the porosity (44–67%) and the pore size (70–178 µm) of porous alumina samples maintained a linear relationship with the PFA loading. Comprehensive mechanical strength characterization of the porous alumina samples was conducted not just as a function of porosity but also as a function of the different PFA type used. Overall, the mechanical properties showed an inverse relationship with the porosity as the developed porous alumina samples exhibited tensile and compressive strengths of 20.4–1.5 MPa and 179.5–10.9 MPa respectively. Moreover, higher strengths were observed in the SCB shaped samples up to the 15 wt% PFA mark, while beyond this point, the silica peak observed in the XRD pattern of the RH shaped samples favored their relatively high strength. The corrosion resistance characterization of the porous alumina samples in hot 10 wt% NaOH and 20 wt% H₂SO₄ solutions was also investigated by considering sample formulations with 5–15 wt% PFA addition. With increasing porosity, the mass loss range in RH and SCB shaped samples after corrosion in NaOH solution for 8 h were 1.25–3.6% and 0.44–2.9% respectively; on the other hand, after corrosion in H₂SO₄ solution for 8 h, the mass loss range in RH and SCB shaped samples were 0.62–1.5% and 0.68–3.3% respectively.     

Influence of sintering atmosphere and BN additives on microstructure and properties of porous SiC ceramics

The effects of the boron nitride (BN) content on the electrical, thermal, and mechanical properties of porous SiC ceramics were investigated in N₂ and Ar atmospheres. The electrical resistivity was predominantly controlled by the sintering atmosphere and secondarily by the BN concentration, whereas the thermal conductivity and flexural strength were more susceptible to changes in the porosity and necking area between the SiC grains. The electrical resistivities of argon-sintered porous SiC ceramics (6.3 × 10⁵ – 1.6 × 10⁶ Ω·cm) were seven orders of magnitude higher than those of nitrogen-sintered porous SiC ceramics (1.5 × 10⁻¹ – 6.0 × 10⁻¹ Ω·cm). The thermal conductivity and flexural strength of the argon-sintered porous SiC ceramics increased from 8.4–11.6 W·m⁻¹ K⁻¹ and from 9.3–28.2 MPa, respectively, with an increase in the BN content from 0 to 1.5 vol%, which was attributed to the increase in necking area and the decrease in porosity.     

Fabrication and properties of SiC porous ceramics using a polyurethane preparation process

SiC porous ceramics can be prepared by introducing the polyurethane preparation method into the production process of ceramic biscuits, followed by sintering at 1300?°C for 2?h under N₂ flux after the cross-linking of polycarbosilane at 220?°C for 4?h in air. The microstructures, mechanical properties and infiltrations of the SiC porous ceramics are investigated in detail. The best dispersal effect comes from the SiC slurry with xylene as the solvent and a mixture of Silok®7096 (1?wt%) and Anjeka®6041 (4?wt%) as the dispersant. The compressive strength of SiC porous ceramics with high porosity (69.53%) reaches 16.9?MPa. The heat treatment can increase infiltration, the rate of which (4.296?×?10^?7 mm²) after the heat treatment at 750?°C in air is approximately two times faster than that before the heat treatment. The SiC porous ceramics fabricated in this study will have potential application in active thermal protection systems.     

Recycling of waste red mud for fabrication of SiC/mullite composite porous ceramics

SiC/mullite composite porous ceramics were fabricated from recycled solid red mud (RM) waste. The porous ceramics were formed using a graphite pore forming agent, RM, Al(OH)₃ and SiC in the presence of catalysts. The influence of firing temperature and the pore-forming agent content on the mechanical performance, porosity and the microstructure of the porous SiC ceramics were investigated. Optimal preparation condition were determined by some testing. The results indicated that the flexural strength of specimens increased as a function of firing temperature and a reduction in graphite content, which concomitantly decreased porosity. The ceramic prepared under optimal conditions having 15?wt% graphite and sintered at 1350?°C, demonstrated excellent performance. Under optimal preparation conditions the flexural strength and porosity of the ceramic were 49.4?MPa and 31.4%, respectively. Scanning electron microscopy observation result showed that rod-shape mullite grains endowed the samples with high flexural strength and porosity. X-ray diffraction analysis indicated that the main crystallization phases of the porous ceramics were 6H-SiC, mullite, cristobalite and alumina. This work demonstrates that RM can be sucessfully reused as a new raw material for SiC/mullite composite porous ceramics.     

Fabrication and microstructure of porous SiC ceramics with Al2O3 and CeO2 as sintering additives

In the present study, porous silicon carbide ceramics were prepared via spark plasma sintering at relatively low temperatures using Al₂O₃ and CeO₂ as sintering additives. Sacrificial template was selected as the pore forming mechanism, and gelcasting was used to fix the slurry in a short time. The evolution process of the microstructures during different steps was observed by SEM. The influence of the sintering temperature and sintering additives on the shrinkage and porosity of the samples was studied. The microstructures of different samples were characterized, and the mechanical properties were also evaluated.     

Effect of starch addition on microstructure and properties of highly porous alumina ceramics

Porous alumina ceramics with ultra-high porosity were prepared through combining the gel-casting process with the pore-forming agent technique. Porosity and pore size distribution of the sintered bulks were evaluated with and without adding starch, respectively. In particular, the influences of starch addition on the properties, including thermal conductivity and compressive strength were studied. It was found that the incorporation of starch increased the nominal solid loading in the suspension and subsequently promoted the particle packing efficiency. The porosity is raised with increasing starch content from 0 to 30 vol%, which brings the decrease in thermal conductivity, whereas the compressive strength isn't seriously degraded. The further higher starch addition (40 vol%), however, would deteriorate the performance of the alumina porous ceramics. It is believed that the appropriate starch amount (lower than 30 vol%), working as a pore-forming agent, suppresses the driving force of densification without affecting the connections of neighboring grains while excessive starch amount would lead to the collapse of the porous structure.     

Microstructure and mechanical properties of cold sintered porous alumina ceramics

New innovative approach to fabricate porous alumina ceramics by cold sintering process (CSP) is presented using NaCl as pore forming agent. The effects of CSP and post-annealing temperature on the microstructure and mechanical strength were investigated. Al₂O₃–NaCl composite with bulk density of 2.92 g/cm³ was compacted firstly using CSP and then a porous structure was formed using post-annealing at 1200°C–1500°C for 30 min. Brazilian test method and Vickers hardness test were used to determine the indirect tensile strength and hardness of the porous alumina, respectively. Meanwhile, the phases and the microstructure were respectively examined using X-ray diffractometer and scanning electron microscope (SEM) complemented by the 3D image analysis with X-ray tomography (XRT). SEM structural and XRT image analysis of cold sintered composite showed a dense structure with NaCl precipitated between Al₂O₃ particles. The NaCl volatization from the composite was observed during the annealing and then complete porous Al₂O₃ structure was formed. The porosity decreased from 48 vol% to 28 vol% with the annealing temperature increased from 1200 °C to 1500 °C, while hardness and mechanical strength increased from 14.3 to 115.4 HV and 18.29–132.82 MPa respectively. The BET analysis also showed a complex pore structure of micropores, mesopores and macropores with broad pore size distribution.     

Mineralogical and dielectric properties of mullite and cordierite ceramics produced using wastes

In this work technical ceramics containing industrial inorganic wastes was carried out. Ceramic formulations prepared with clay, magnesium oxide and residues of kaolin and alumina as raw materials, were formed in a disk-shaped specimens using the uniaxial pressing process and sintering at temperatures from 950°C to 1400°C. The mineralogical, physical and dielectric characteristics of the fired samples were investigated. The dielectric properties, the relative dielectric constant (ε_r) and the loss tangent (tan δ) were evaluated at frequencies of 0.1, 1, 10, and 100?kHz at room temperature. Mullite and cordierite were present as major phases at the highest temperatures. Relative dielectric constant values closest to that of mullite (ε_r = ~ 5 to ~ 6) and cordierite (ε_r =?~ 4 to ~ 6) at 1?kHz. On the other hand, the lowest dielectric losses (tan δ ~ 0.06 to ~ 0.04) were observed for the formulations containing the mullite major phase, and tan δ ~ 0.009 to ~ 0.003 for formulations that showed cordierite as main phase. It was verified that an increase in temperature promoted a reduction of porosity, a property that had a direct influence on the dielectric properties of the formulations. The materials obtained from the residues presented low dielectric constants and loss tangents, which make them suitable for use in electrical and electronic systems.     

Porous cordierite-based ceramics processed by starch consolidation casting – Microstructure and high-temperature mechanical behavior

Porous cordierite-based ceramics with different microstructural features and mechanical behavior were formed by starch consolidation casting (SCC) using native potato and corn starches and sintered at 1275, 1300 and 1330 °C. The composition and microstructure of the ceramic materials were investigated via quantitative phase analysis using X-ray diffraction (with Rietveld refinement), the Archimedes method, mercury porosimetry, scanning electron microscopy and optical microscopy with stereology-based image analysis. The mechanical behavior of samples was evaluated by diametral compression tests at room temperature, 1000 and 1100 °C. The type of starch used and the sintering temperatures were the main factors determining the characteristics of the developed porous microstructures. Materials prepared with corn starch achieved the lowest porosity and the lowest values of mean chord length, mean pore distance and pore throat size. Because of these features, these materials thus presented, in general, higher values of apparent Young's modulus, elastic limit and mechanical strength than those prepared with potato starch. Despite the presence of a silicate glassy phase, both porous materials, mainly those prepared with corn starch, still enhanced the basic mechanical properties at high temperature, in particular, the mechanical strength and the apparent Young's modulus due to the special combination of the porous microstructure features.     

Microstructure evolution and bonding mechanisms of silica sol bonded coating at elevated temperatures

High emissivity coating plays a critical role in thermal protective system, which can radiate a large amount of aero-convective heat. Silica sol bonded MoSi₂-SiC-Al₂O₃ (S-MSA) coating was proved to be promising for mullite fibrous insulation. However, the bonding mechanisms of the coating at elevated temperatures are not clear. In this work, the S-MSA coatings were heat-treated at temperatures from 600 °C to 1500 °C to reveal the bonding mechanisms at elevated temperatures. The S-MSA coatings go through a relatively stable stage (600 °C–1000 °C), a crystallization stage (1100 °C–1200 °C), and a densification stage (1300 °C–1500 °C) at ever increasing temperatures. Results show that both the contact damage resistance and the bonding strength of the calcined coatings exhibit a decrease followed by an increase at elevated calcination temperatures, with the inflection point at 1200 °C, corresponding to the transition temperature of the bonding mechanisms from 600 °C to 1500 °C.     

Improvement of the mechanical properties of SiC reticulated porous ceramics with optimized three-layered struts for porous media combustion

Silicon carbide reticulated porous ceramics (SiC RPCs) with three-layered struts were fabricated by polymer replica method, followed by infiltrating alumina slurries containing silicon (slurry-Si) and andalusite (slurry-An), respectively. The effects of composition of infiltration slurries on the strut structure, mechanical properties and thermal shock resistance of SiC RPCs were investigated. The results showed that the SiC RPCs infiltrated with slurry-Si and slurry-An exhibited better mechanical properties and thermal shock resistance in comparison with those of alumina slurry infiltration, even obtained the considerable strength at 1300 °C. In slurry-Si, silicon was oxidized into SiO₂ in the temperature range from 1300 °C to 1400 °C and it reacted with Al₂O₃ into mullite phase at 1450 °C. Meantime, the addition of silicon in slurry-Si could reduce SiC oxidation of SiC RPCs during firing process in contrast with alumina slurry. With regard to slurry-An, andalusite started to transform into mullite phase at 1300 °C and the secondary mullitization occurred at 1450 °C. The enhanced mechanical properties and thermal shock resistance of SiC RPCs infiltrated alumina slurries containing silicon and andalusite were attributed to the optimized microstructure and the triangular zone (inner layer of strut) with mullite bonded corundum via reaction sintering. In addition, the generation of residual compressive stress together with better interlocked needle-like mullite led to the crack-deflection in SiC skeleton, thus improving the thermal shock resistance of obtained SiC RPCs.     

A new approach for the net-shape fabrication of porous Si3N4 bonded SiC ceramics with high strength

In this study, Si₃N₄ bonded porous SiC ceramics with high strength had been net-shapely fabricated by a new approach. In this approach, we proposed a two-step processing route composed of freeze casting and carbothermal reduction reactions in which carbon aerogels, derived from sol infiltration and pyrolysis, involved. The phase components, microstructures and properties of the prepared ceramics were investigated. The results showed that carbon aerogels with high apparent surface area had been completely reacted and new SiC and Si₃N₄ grains had been produced. The porous ceramics with flexural strength of 164.3 MPa at 33% porosity and 80.5 MPa at 46% porosity were obtained, whose linear shrinkages were only 1.06% and 1.94% during the whole processing respectively.     

Fabrication of SiC reticulated porous ceramics with multi-layered struts for porous media combustion

Silicon carbide reticulated porous ceramics (SiC RPCs) with multi-layered struts were fabricated at 1450 °C by polymer sponge replica technique, followed by vacuum infiltration. The effect of additives (polycarboxylate, ammonium lignosulfonate and sodium carboxymethyl-cellulose) on the rheological behavior of silicon carbide slurry was firstly investigated, and then the slurry was coated on polyurethane open-cell sponge template. Furthermore, alumina slurry was adopted to fill up the hollow struts in vacuum infiltration process after the coated sponge was pre-treated at 850 °C. The results showed that the coating thickness on the struts and the microstructure in SiC RPCs were closely associated with the solid content of alumina slurry during vacuum infiltration. The typical multi-layered strut of SiC RPCs could be achieved after the infiltration of an alumina slurry containing 77 wt% solid content. The compressive strength and thermal shock resistance of the infiltrated specimens were significantly improved in comparison with those of non-infiltrated ones. The improvement was attributed to the in-situ formation of reaction-bonded multilayer struts in SiC RPCs, which were characterized by the exterior coating of aluminosilicate-corundum, middle part of mullite bonded SiC and interior zone of corundum.     

Microstructure and properties of porous SiC ceramics by LPCVI technique regulation

A new gradient pore structure in porous SiC ceramics was fabricated by low pressure chemical vapor infiltration (LPCVI). Effects of deposition duration on the mechanical properties and permeability of porous SiC ceramics were investigated. Results demonstrated that pore diameter and shapes decreased from the surface to the interior along with LPCVI duration. Porous SiC ceramics with deposition duration of 160 h exhibited flexural strength of 48.05 MPa and fracture toughness of 1.30 MPa m^1/2, where 221% and 189% improvements were obtained compared to porous SiC ceramics without LPCVI, due to CVI-SiC layer strengthening effect. Additionally, at the same gas velocity, pressure drop increase rate was faster due to apparent porosity and pore size change.     

Microstructure and properties of lightweight fibrous porous mullite ceramics prepared by vacuum squeeze moulding technique

A novel fibrous porous mullite network with a quasi-layered microstructure was produced by a simple vacuum squeeze moulding technique. The effects of organic binder content, inorganic binder and adsorbent on the microstructure and the room-temperature thermal and mechanical properties of fibrous porous mullite ceramics were systematically investigated. An anisotropy microstructure without agglomeration and layering was achieved. The fibrous porous mullite ceramics reported in this study exhibited low density (0.40 g/cm³), low thermal conductivity (~0.095 W/(m K)), and high compressive strength (~2.1 MPa in the x/y direction). This study reports an optimal processing method for the production of fibrous porous ceramics, which have the potential for use as high-temperature thermal insulation material.     

碳化硅-堇青石多孔陶瓷的制备及其性能

以碳化硅粉末、高岭土和滑石等为原料,按堇青石的化学计量比设计原料配比,制备了堇青石理论生成量分别为0、10%、15%、20%、100%的碳化硅-堇青石多孔陶瓷,测定了试样的抗折强度、显气孔率和热膨胀系数,并分别用XRD和SEM分析了试样的晶相组成和断面形貌。结果表明:与碳化硅多孔陶瓷相比,碳化硅-堇青石多孔陶瓷的抗折强度显著提高,热膨胀系数明显降低,但显气孔率有所降低。SEM分析结果表明:碳化硅-堇青石多孔陶瓷中碳化硅颗粒排列较紧密,断面呈“网格状”结构;而在多孔碳化硅陶瓷中,晶粒形貌清晰且排列较疏松,气孔平均孔径较大。     

Structural and functional properties of BaTiO3 porous ceramics produced by using pollen as sacrificial template

The present paper reports the dependence of structural and functional properties on the porosity level with values down to 50% in BaTiO₃ ceramics. Micro-porosity (pore size below 15 μm) with (0–3) connectivity has been produced by using dried pollen particles as sacrificial template. The properties of such porous ceramics are mostly affected by porosity, but also by possible small doping with foreign ions resulted from the template and by small variations of Ba/Ti stoichiometry at the ceramic-pore interfaces, as observed by a shift of the Curie temperature towards lower values when porosity level increases. The dielectric relaxation evidenced a few processes characterised by different activation energies which seem to be not affected by porosity, i.e. they might be assigned to the ceramic part and not to the ceramic-pore interfaces. When increasing porosity, a regular tilting of P(E) loops and increasing of coercivity and reducing polarization were observed, as result of reduction of active ferroelectric component and to the field inhomogeneity in such ceramics.     

Mechanical properties of porous MgO substrates for membrane applications

Advanced design concepts for the application of oxygen transport ceramic membranes are based on thin layers supported by porous substrates. One suitable support material in this respect is porous MgO. However, a careful consideration of the mechanical stability is required to warrant long term performance and reliability under application relevant thermo-mechanical loads. The current work summarizes the effect of the sintering conditions on porosity and mechanical properties and gives elastic modulus and fracture stress as a function of temperature. An enhancement of the strength by the addition of boehmite to MgO was tested. Elastic moduli are determined and compared as obtained by indentation and bending tests. With respect to fracture, specimens in planar geometry are investigated using ring-on-ring bending tests; tubes are tested using an O-ring set-up. Fracture stresses are statistically analyzed. The obtained mechanical parameters are compared to that of other potential porous substrate materials.     

Processing and properties of silica-bonded porous nano-SiC ceramics with extremely low thermal conductivity

Silica-bonded porous nano-SiC ceramics with extremely low thermal conductivity were prepared by sintering nano-SiC powder-carbon black template compacts at 600–1200 °C for 2 h in air. The microstructure of the silica-bonded porous nano-SiC ceramics consisted of SiC core/silica shell particles, a silica bonding phase, and hierarchical (meso/macro) pores. The porosity and thermal conductivity of the silica-bonded porous nano-SiC ceramics can be controlled in the ranges of 8.5–70.2 % and 0.057–2.575 Wm⁻¹ K⁻¹, respectively, by adjusting both, the sintering temperature and template content. Silica-bonded porous nano-SiC ceramics with extremely low thermal conductivity (0.057 Wm⁻¹ K⁻¹) were developed at a very low processing temperature (600 °C). The typical porosity, average pore size, compressive strength, and specific compressive strength of the porous nano-SiC ceramics were ∼70 %, 50 nm, 2.5 MPa, and 2.7 MPa·cm³/g, respectively. The silica-bonded porous nano-SiC ceramics were thermally stable up to 1000 °C in both air and argon atmospheres.     

Assembling unidirectionally frozen alumina/camphene bodies for aligned porous alumina ceramics with larger dimensions

This paper proposes a novel way of producing aligned porous alumina ceramics with larger dimensions by assembling unidirectionally frozen alumina/camphene bodies, particularly those containing polystyrene (PS) polymer as the binder. The compressive strength of the samples sintered at 1450 °C for 3 h increased remarkably from 2 ± 0.1 to 16 ± 2 MPa with increasing PS content from 5 to 20 vol.% due to the prevention of cracks generally caused by drying shrinkage. In addition, frozen samples with a PS content of 20 vol.% could be assembled into larger dimensions without difficulty. The height of the assembled sample produced with a lamination number of 5 could be increased to ∼24 mm without a severe decrease in compressive strength (16 ± 3 MPa at a porosity of ∼79 vol.%) due to the maintenance of an aligned porous structure with good interfacial bonding between the laminations.