Microstructure and mechanical properties of (Ti,W)C cermets prepared by ultrafast spark plasma sintering

To explore the impact of the sintering rate on the microstructure and mechanical properties of cermets, the preparation of (Ti,W)C cermets by ultrafast sintering via spark plasma sintering (SPS) is reported. Compared with a slow heating rate, the electric field produced by an ultrafast heating rate enhances the liquid phase mass transfer of the metal binder phase, thus achieving rapid densification of (Ti,W)C cermets and effectively inhibiting abnormal grain growth. However, an excessive heating rate will lead to an “overflow” phenomenon, which reduces the grain growth difficulty and the bonding strength between grains. The results show that when the heating rate is 500 °C/min, the liquid phase mass transfer is moderate, the densification degree is the highest and the mechanical properties are excellent. The flexural strength, Vickers hardness and fracture toughness are 1340.90 ± 23.55 MPa, 18.42 ± 0.46 GPa and 11.96 ± 0.23 MPa?m^1/2, respectively.     

Improvement in microstructure and mechanical properties of Ti(C,N) cermet prepared by two-step spark plasma sintering

A fine grained Ti(C, N) cermet tool material was prepared by two-step spark plasma sintering. Microstructure evolution and densification mechanisms of Ti(C, N) during spark plasma sintering were studied. Effect of two-step sintering process and Ni content on microstructure and mechanical properties were also investigated. The critical activated densification temperature of Ti(C, N) is about 1300?℃, and the rapidest densification rate takes place at 1300?℃~1400?℃. Grains are in the size of 1?µm when the Ti(C, N) cermet was prepared by two-step spark plasma sintering. The optimal flexural strength, fracture toughness and Vickers hardness are 1094?±?42?MPa, 7.2?±?0.5?MPa?m^1/2 and 18.3?±?0.4?GPa, respectively. The Ti(C, N) cermets containing more content of Ni have higher toughness, which is due to the remarkable toughening effect of crack bridging by large grains.     

Microstructure and mechanical properties of B4C based ceramics with Fe3Al as sintering aid by spark plasma sintering

B₄C based ceramics were fabricated with different Fe₃Al contents as sintering aids by spark plasma sintering at relatively low temperature (1700 °C) in vacuum by applying 50 MPa pressure and held at 1700 °C for 5 min. The effect of Fe₃Al additions (from 0 to 9 wt%) on the microstructure and mechanical properties of B₄C has been studied. The composition and microstructure of as-prepared samples were characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM) and electron probe microanalyzer (EPMA) equipped with WDS (wavelength dispersive spectrometry) and EDS. The mixtures of B₄C and Fe₃Al underwent a major reaction in which the metal borides and B₄C were encountered as major crystallographic phases. The sample with 7 wt% of Fe₃Al as a sintering aid was found to have 32.46 GPa Vickers hardness, 483.40 MPa flexural strength, and 4.1 MPa m^1/2 fracture toughness which is higher than that of pure B₄C.     

Mechanical properties and microstructures of TiCN/nano-TiB2/TiN cermets prepared by spark plasma sintering

The effects of TiN and nano-TiB₂ additions to titanium carbonitride (TiCN-WC-Cr₃C₂-Co)-based cermets processed by spark plasma sintering (SPS) are identified. The TiN and nano-TiB₂ additions were varied from 0 to 15?wt% to ascertain their combined effects on the mechanical properties. Scanning electron microscopy (SEM) revealed the combined chemical composition of the new phases formed during sintering. The hardness and fracture toughness values were recorded. Increase in the fracture toughness value with TiN addition was more compared with the nano-TiB₂ addition. In contrast, the hardness values were higher for the cermets formed with the nano-TiB₂ addition. Sintered bodies were made as tool inserts that meet SNGN120408 standard tool configuration. Using these tools, EN24 work-piece was turned at different cutting speeds of 11.87, 29.68, 71.46, 163.88?m/min under conditions of dry cutting. The performance was evaluated. Cutting force as well as surface roughness of the work-piece after machining was measured. For all cutting tools, initially the cutting force was high but it tended to decrease at higher cutting speeds. In addition, for all the tools, at higher cutting tools the surface roughness values were uniformly minimal. The cermet with a composition 55TiCN-15WC-10Co-5Cr₃C₂–15nanoTiB₂ (all in wt%), in particular, showed a balanced enhancement in both fracture toughness (6.8?MPa?m^1/2) and Vickers hardness (18?GPa) values. The surface finish of the work-piece was also the best after machining when a tool of the above composition was used.     

Microstructure and mechanical properties of SiC-SiC joints joined by spark plasma sintering

The development of reliable joining technology is of great importance for the full use of SiC. Ti₃SiC₂, which is used as a filler material for SiC joining, can meet the demands of neutron environment applications and can alleviate residual stress during the joining process. In this work, SiC was joined using different powders (Ti₃SiC₂ and 3Ti/1.2Si/2C/0.2Al) as filler materials and spark plasma sintering (SPS). The influence of the joining temperature on the flexural strength of the SiC joints at room temperature and at high temperatures was investigated. Based on X-ray diffraction and scanning electron microscopy analyses, SiC joints with 3Ti/1.2Si/2C/0.2Al powder as the filler material possess high flexural strengths of 133 MPa and 119 MPa at room temperature and at 1200 °C, respectively. The superior flexural strength of the SiC joint at 1200 °C is attributed to the phase transformation of TiO₂ from anatase to rutile.     

Densification,microstructures, and mechanical properties of (Zr,Ti)(C,N) ceramics fabricated by spark plasma sintering

Dense (Zr, Ti) (C, N) ceramics were fabricated by spark plasma sintering (SPS) at 1900–2000 °C using ZrC, TiCN and ZrH₂ powders as raw materials. A single Zr-rich (Zr, Ti)(C, N) solid solution was formed in Zr_0.95Ti_0.05C_0.975N_0.025 and Zr_0.80Ti_0.20C_0.90N_0.10 ceramics (nominal composition). A Ti-rich solid solution appears in Zr_0.50Ti_0.50C_0.75N_0.25 ceramics. The coaddition of TiCN and ZrH₂ promoted the densification of (Zr, Ti) (C, N) ceramics by forming solid solutions and carbon vacancies, which could reduce critical resolved shear stress (CRSS) and promote carbon and metal atom diffusion. ZrC-45 mol% TiCN-10 mol% ZrH₂ (raw powder composition) possesses good comprehensive mechanical properties (Vickers hardness of 24.5 ± 0.9 GPa, flexural strength of 503 ± 51 MPa, and fracture toughness of 4.3 ± 0.2 MPa·m^1/2), which reach or exceed most ZrC-based (Zr, Ti) C and (Zr, Ti) (C, N) ceramics in previous reports.     

Microstructure and magnetic properties of nickel-zinc ferrite ceramics fabricated by spark plasma sintering

Dense nickel-zinc (NiZn) ferrite ceramics were successfully fabricated within tens of seconds via spark plasma sintering. The phase composition and microstructure of the sintered samples were characterized by X-ray diffraction and scanning electron microscopy, respectively. The static magnetic properties at room temperature and Curie temperature of the samples were investigated by vibrating sample magnetometry. The results indicated that the main phase of the sintered samples was Ni_0.75Zn_0.25Fe₂O₄ with spinal structure, and the sintering temperature and heating rate observably affected the microstructure and density, then the magnetic properties of the sample. The Joule heat generated by NiZn ferrite during spark plasma sintering was very important for the rapid preparation of the sample with high density and small grain size. The low sintering temperature and heating rate would be helpful to obtain samples with small grain size, high density, and then good magnetic properties. The samples sintered at 900 °C with the heating rate of 5–10 °C/s were characterized of the relative density above 95%, 4πM_s value beyond 4000 Gs and coercivity below 27.7 Oe.     

Coarse-grain CeO2 doped ZrO2 ceramic prepared by spark plasma sintering

In the present work, coarse grain cerium stabilized zirconia bulk ceramic was prepared by spark plasma sintering technique. The relatively high temperature of 2000 °C used for sintering led to enormous grain growth up to approximately 100 μm. Sintering at high temperatures and in the vacuum caused oxygen depletion and thus transformation from tetragonal to cubic phase during the sintering process. The tetragonal phase was recovered by annealing at 1400 °C in air. This led to a change in fracture behavior. Mostly transgranular fracture of the cubic phase was changed to intergranular fracture after recovering the tetragonal phase. On the intergranular fracture surface, twinning-like structure and structures similar to antiphase domain were observed.Mechanical properties represented by indentation hardness of prepared samples were evaluated.     

放电等离子烧结合成单相MgAlON材料

以氮化铝、富铝镁铝尖晶石和氧化铝为原料 ,用放电等离子烧结 (SPS)技术合成了单相MgAlON,研究了其显微结构 ,并与用传统的无压烧结 (PLS)技术制备的单相MgAlON材料在显微结构和断裂行为上做了比较。结果表明 :用SPS法在 170 0℃保温 1min的条件下合成出的单相MgAlON材料 ,显微结构比用PLS法合成的更加均匀致密 ,且晶粒细小 ;前者的断裂模式主要是穿晶断裂 ,后者的断裂模式则主要是沿晶断裂。     

Preceramic paper-derived Ti3Al(Si)C2-based composites obtained by spark plasma sintering

The paper describes the structure and properties of preceramic paper-derived Ti₃Al(Si)C₂-based composites fabricated by spark plasma sintering. The effect of sintering temperature and pressure on microstructure and mechanical properties of the composites was studied. The microstructure and phase composition were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. It was found that at 1150 °C the sintering of materials with the MAX-phase content above 84 vol% leads to nearly dense composites. The partial decomposition of the Ti₃Al(Si)C₂ phase becomes stronger with the temperature increase from 1150 to 1350 °C. In this case, composite materials with more than 20 vol% of TiC were obtained. The paper-derived Ti₃Al(Si)C₂-based composites with the flexural strength > 900 MPa and fracture toughness of >5 MPa m^1/2 were sintered at 1150 °C. The high values of flexural strength were attributed to fine microstructure and strengthening effect by secondary TiC and Al₂O₃ phases. The flexural strength and fracture toughness decrease with increase of the sintering temperature that is caused by phase composition and porosity of the composites. The hardness of composites increases from ~9.7 GPa (at 1150 °C) to ~11.2 GPa (at 1350 °C) due to higher content of TiC and Al₂O₃ phases.     

Microstructure characteristic and its influence on the strength of SiC ceramic joints diffusion bonded by spark plasma sintering

The interfacial microstructure evolution and shear strength of SiC joints for high temperature applications diffusion bonded by spark plasma sintering with a Ta-5W interlayer in the temperature range of 1500 °C to 1700 °C were investigated. The interfacial microstructure analysis indicated that (Ta,W)C phase formed initially and (Ta,W)-Si intermetallic compounds subsequently at SiC/Ta-5W interface. Bonding temperature had a significant effect on the reaction layer thickness, which increased with increasing the bonding temperature, and holding time also has an influence on reaction layer thickness. Calculation of diffusion kinetics for the SiC/Ta-5W interface showed that the diffusion constant was about two orders of magnitude larger than that obtained by hot-pressing bonding, and the activation energy was almost one-tenth that of hot-pressing bonding. Both the reaction layer thickness and the interfacial defects had a great effect on the robustness of the joint, and the maximum shear strength of 122 ± 15 MPa was obtained for the joint bonded at 1600 °C for 5 min.     

Structural properties and mechanical behavior of SWCNTs and MWCNTs reinforced Al2O3 fabricated by spark plasma sintering

Carbon nanotubes due to their structural and mechanical properties are good candidates as the second phase to improve the mechanical properties of alumina-based ceramics. In the present study, the effects of single wall and multi-wall carbon nanotubes on structural and mechanical properties of alumina were investigated. SWCNTs and MWCNTs were dispersed in alumina powder via a conventional method using 1 wt % PVA water solution as media. Sintering process for two different composite powders, alumina-2 wt. % SWCNTs and alumina 2 wt % MWCNTs was performed by spark plasma sintering technique at 1500 °C and 20 MPa for 10 min. Results showed that the presence of CNTs in alumina caused a considerable amount of porosity in final bodies. SEM images of fracture surfaces revealed the agglomeration of SWCNTs which played a dominant role in the deterioration of mechanical properties. MWCNTs reinforced alumina obtained higher Vickers hardness and bending strength values (12.91 GPa and 291 MPa, respectively) compared to that of SWCNTs (9.18 GPa and 276 MPa, respectively), due to sever agglomerate of SWCNTs throughout sintered composites. Typical load-displacement (P/h) curves were obtained from bending strength test and discussed. It was concluded that the addition of MWCNTs to alumina represented better densification and mechanical properties compared to SWCNTs.     

Influence of CeO2 addition on the microstructure and mechanical properties of Zirconia-toughened alumina (ZTA) composite prepared by spark plasma sintering

In this study, zirconia-toughened alumina (ZTA) samples with different amounts of CeO₂ were prepared by the spark plasma sintering method. The phase composition and microstructure of the samples were examined by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The addition of CeO₂ results in grain refinement and density increase; moreover, CeO₂ stabilises the high-temperature metastable phase. As the amount of CeO₂ reaches 7 wt%, a new CeAl₁₁O₁₈ phase appears. The Vickers hardness, modulus, and fracture toughness of the samples depend to a large extent on the grain size, relative density, and existence of the second phase. Among the composites, that with 5 wt% CeO₂ shows the best performance with the highest values of relative density, Vickers hardness, and fracture toughness: 96.51%, 1688 HV, and 9.91 MPa.√m, respectively.     

Static and dynamic mechanical properties of boron carbide processed by spark plasma sintering

Spark plasma sintering (SPS) has become a popular technique for the densification of covalent ceramics. The present investigation is focused on the static mechanical properties and dynamic compressive behavior of SPS consolidated boron carbide powder without any sintering additives. Fully dense boron carbide bodies were obtained by a short high temperature SPS treatment. The mechanical properties of the SPS-processed material, namely hardness (32 GPa), Young modulus (470 GPa), fracture toughness K_C (3.9–4.9 MPa m^0.5), flexural strength (430 MPa) and Hugoniot elastic limit (17–19 GPa) are close or even better than those of hot-pressed boron carbide.     

Microstructure and properties of a graphene platelets toughened boron carbide composite ceramic by spark plasma sintering

A kind of B₄C/SiC composite ceramic toughened by graphene platelets and Al was fabricated by spark plasma sintering. The effects of graphene platelets and Al on densification, microstructure and mechanical properties were studied. The sintering temperature was decreased about 125–300?°C with the addition of 3–10?wt% Al. Al can also improve fracture toughness but decrease hardness. The B₄C/SiC composite ceramic with 3?wt%Al and 1.5?wt% graphene platelets sintered at 1825?°C for 5?min had the optimal performances. It was fully densified, and the Vickers hardness and fracture toughness were 30.09?±?0.39?GPa and 5.88?±?0.49?MPa?m^1/2, respectively. The fracture toughness was 25.6% higher than that of the composite without graphene platelets. The toughening mechanism of graphene platelets was also studied. Pulling-out of graphene platelets, crack deflection, bridging and branching contributed to the toughness enhancement of the B₄C-based ceramic.     

Monoclinic phase-free,low temperature spark plasma sintering of CeO2-doped ZrO2 ceramics and its associated benefits on mechanical properties

Consolidating a CeO₂-doped ZrO₂ ceramics, free from monoclinic phase using spark plasma sintering (SPS) is a major challenge faced by previous researchers; Ce⁺⁴ → Ce⁺³ conversion under reducing environments was assigned as the prime factor. We report dense (> 95 % of theoretical density) 20 mol. % CeO₂-doped ZrO₂ ceramics, free from monoclinic phase and any of micro/ macro-cracks via SPS. The sintering temperature (1175 ℃) used for the present work was the lowest compared to previous reports on the same system. Phase analysis revealed a mixture of tetragonal (major phase) and cubic phase (minor). No depletion of cerium (Ce) from the ZrO₂ matrix and no additional/impurity phases were noted after SPS; a common issue that has been observed in most of the previous works. Sintered ceramics showed appreciably high hardness (>11 GPa); the obtained toughness was in-between of tetragonal and cubic CeO₂-ZrO₂ ceramics.     

Processing and mechanical properties of B4C-SiCw ceramics densified by spark plasma sintering

Homogenous distribution of whiskers in the ceramic matrix is difficult to be achieved. To solve this problem, B₄C-SiC_w powder mixtures were freeze dried from a slurry dispersed by cellulose nanofibrils (CellNF) in this work. Dense B₄C ceramics reinforced with various amounts of SiC_w up to 12 wt% were consolidated by spark plasma sintering (SPS) at 1800 °C for 10 min under 50 MPa. During this process, CellNF was converted into carbon nanostructures. As iron impurities exist in the starting B₄C and SiC_w powders, both thermodynamic calculations and microstructure observations suggest the dissolution and precipitation of SiC_w in the liquids composed of Fe-Si-B-C occurred during sintering. Although not all the SiC_w grains were kept in the final ceramics, B₄C-9 wt% SiC_w ceramics sintered at 1800 °C still exhibit excellent Vickers hardness (35.5 ± 0.8 GPa), flexural strength (560 ± 9 MPa) and fracture toughness (5.1 ± 0.2 MPa·m^1/2), possibly contributed by the high-density stacking faults and twins in their SiC grains, no matter in whisker or particulate forms.     

Sintering effect on microstructural evolution and mechanical properties of spark plasma sintered Ti matrix composites reinforced by reduced graphene oxides

Ti matrix composites reinforced with 0.6?wt% reduced graphene oxide (rGO) sheets were fabricated using spark plasma sintering (SPS) technology at different sintering temperatures from 800?°C to 1100?°C. Effects of SPS sintering temperature on microstructural evolution and mechanical properties of rGO/Ti composites were studied. Results showed that with an increase in the sintering temperature, the relative density and densification of the composites were improved. The Ti grains were apparently refined owing to the presence of rGO. The optimum sintering temperature was found to be 1000?°C with a duration of 5?min under a pressure of 45?MPa in vacuum, and the structure of rGO was retained. At the same time, the reaction between Ti matrix and rGO at such high sintering temperatures resulted in uniform distribution of micro/nano TiC particle inside the rGO/Ti composites. The sintered rGO/Ti composites exhibited the best mechanical properties at the sintering temperature of 1000?°C, obtaining the values of micro-hardness, ultimate tensile strength, 0.2% yield strength of 224 HV, 535?MPa and 446?MPa, respectively. These are much higher than the composites sintered at the temperature of 900?°C. The fracture mode of the composites was found to change from a predominate trans-granular mode at low sintering temperatures to a ductile fracture mode with quasi-cleavage at higher temperatures, which is consistent with the theoretical calculations.     

Microstructure and mechanical properties of spark plasma sintered TiB2 ceramics combined with a high-entropy alloy sintering aid

A high-entropy alloy (HEA), CoCrFeNiMn_0.5Ti_0.5, is used as a sintering aid for the densification of TiB₂ sintered by spark plasma sintering. The HEA content in the starting TiB₂-HEA mixture is varied from 0 to 10?wt-%. The microstructure and mechanical properties of the sintered samples are analysed and the optimum HEA content of 10% is found for the preparation of the TiB₂-HEA ceramics, allowing combining high mechanical properties (Vickers hardness of 2174.64?HV and flexural strength of 427.69?MPa) and high relative density of 99.1%.     

Densification,microstructure and properties of ultra-high temperature HfB2 ceramics by the spark plasma sintering without any additives

Ultra-high temperature HfB₂ ceramic with nearly full densification is achieved by using gradient sintering process of SPS without any additives. The effect of the sintering temperature on the densification behavior, relative density, microstructure, mechanical and thermionic properties is systematically investigated. The results show that the fast densification of HfB₂ ceramic occurs at the heating stage, and the highest relative density of 96.75% is obtained at T =1950 °C, P = 60 MPa and t =10min. As the temperature is increased from 1800 to 1950 °C, the grain size of HfB₂ increases from 6.12 ±1.33 to 10.99 ± 2.25 μm, and refined microstructure gives the excellently mechanical properties. The highest hardness of 26.34 ±2.1GPa, fracture toughness of 7.12 ± 1.33 MPa m^1/2 and bending strength of 501 ±10MPa belong to the HfB₂ ceramic obtained at T =1950°C. Moreover, both the Vickers hardness and fracture toughness obey the normal indentation size effect. HfB₂ ceramic also exhibits the thermionic emission characterization with the highest current density of 6.12 A/cm² and the lowest work function of 2.92 eV.