Self-standing flexible cathode of V2O5 nanobelts with high cycling stability for lithium-ion batteries

Self-standing V₂O₅ nanobelt electrode free of binders, conductive carbon or current collectors was successfully prepared via a simple one-step hydrothermal reaction. The length of V₂O₅ nanobelts was up to several hundreds micrometers and the thickness was around 40 nm. Ultralong nanobelts as building blocks and internal voids provide a robust mechanical flexibility and shortened ion/electron transport pathway. The self-standing electrode delivered an initial specific capacity of 127.4 mA h g⁻¹ at a current density of 60 mA g⁻¹ and exhibited excellent cycling stability with capacity retention up to 89.8% after 200 cycles. The outstanding cycling performance can be attributed to the excellent network stability, shortened Li-ion diffusion pathway and the high surface area between electrolyte/electrode interfaces.     

Evaluation of reduced graphene oxide-supported NiSb2O6 nanocomposites for reversible lithium storage

NiSb₂O₆ and reduced graphene oxide (NiSb₂O₆/rGO) nanocomposites are successfully fabricated by a solid-state method combined with a subsequent solvothermal treatment and further used as anode material of lithium-ion battery. The NiSb₂O₆/rGO nanocomposites exhibit a higher reversible capacity (of ca. 1240.5 mA h g⁻¹ at a current density of 50 mA g⁻¹), along with a good rate capability (395.2 mA h g⁻¹ at a current density of 1200 mA g⁻¹) and excellent capacity retention (684.5 mA h g⁻¹ after 150 cycles). These good performances could be attributed to the incorporated reduced grapheme oxide, which significantly improves the electronic conductivity of the NiSb₂O₆.     

Synthesis and characterization of MnCo2O4 microspheres based air electrode for rechargeable sodium-air batteries

In this work, the nanosized porous MnCo₂O₄ microspheres were synthesized by a hydrothermal method and their electrochemical behaviors were investigated based on a carbon supported composite air electrode for rechargeable sodium-air batteries. Under dry air test condition, the MnCo₂O₄/C air electrode demonstrated a stable working voltage of around 2.1 V vs. Na⁺/Na and a high initial discharge capacity of 7709.4 mA h g⁻¹, based on the active material mass, at a current density of 0.1 mA cm⁻². By a limit on the depth of discharge, the cell exhibited a specific capacity of 1000 mA h g⁻¹ with a high cycling stability up to 130 cycles. The considerable electrocatalytic activity suggests that the as-proposed MnCo₂O₄ is a highly efficient catalyst as air electrode for rechargeable sodium-air batteries.     

Hydrothermal synthesis of spherical Li4Ti5O12 material for a novel durable Li4Ti5O12/LiMn2O4 full lithium ion battery

Pure spherical Li₄Ti₅O₁₂ spinel material is quickly synthesized via an efficient hydrothermal procedure. The obtained Li₄Ti₅O₁₂ particle size is about 0.5 µm. The Li₄Ti₅O₁₂ has an initial discharge capacity of 162.2 mA h g⁻¹ and capacity retention of 97.5% after 100 cycles at a rate of 0.2 C. Then, a 2.5 V and long-lasting Li-ion cell with a LiMn₂O₄ cathode and a Li₄Ti₅O₁₂ anode is developed. Electrochemical measurements of the cell indicate that the Li₄Ti₅O₁₂/LiMn₂O₄ full cell, with a weight ratio of 1.5 between cathode and anode, exhibits excellent electrochemical performance, delivering a reversible capacity of 130 mA h g⁻¹ at room temperature. The full cell also exhibits outstanding electrochemical performances at high temperature, as it has an initial discharge capacity of 109.6 mA h g⁻¹, along with a capacity retention rate of 88.9% after 100 cycles at 55 °C.     

Bitter gourd-shaped Ni3V2O8 anode developed by a one-pot metal-organic framework-combustion technique for advanced Li-ion batteries

The present study reports on the one-pot synthesis of Ni₃V₂O₈ (NVO) electrodes by a simple metal organic framework-combustion (MOF-C) technique for anode applications in Li-ion batteries (LIBs). The particle morphology of the prepared NVO is observed to vary as irregular rods, porous bitter gourd and hybrid micro/nano particles depending on the concentration of the framework linker used during synthesis. In specific, the orthorhombic phase and the unique bitter gourd-type secondary structure comprised of agglomerated nanoparticles and porous morphologies is confirmed using powder X-ray diffraction, electron microscopies, X-ray photoelectron spectroscopy and N₂ adsorption–desorption measurements. When tested for lithium batteries as anode, the bitter gourd-type NVO electrode shows an initial discharge capacity of 1362 mA h g⁻¹ and a reversible capacity of 822 mA h g⁻¹ are sustained at a rate of 200 mA g⁻¹ after 100 cycles. Moreover, at 2000 mA g⁻¹, a reversible capacity of 724 mA h g⁻¹ is retained after 500 cycles. Interestingly, the porous bitter gourd-shaped NVO electrode registered significantly high rate performance and reversible specific capacities of 764, 531 and 313 mA h g⁻¹ at high rates of 1, 5 and 10 A g⁻¹, respectively.     

Nb2O5 nanospheres/surface-modified graphene composites as superior anode materials in lithium ion batteries

Uniform Nb₂O₅ nanospheres/surface-modified graphene (SMG) composites for anode materials in lithium ion batteries were synthesized by hydrothermal method. The microstructure and morphology of composites were investigated by X-ray diffraction, scanning electron microscopy and transmission electron microscope techniques. The experimental results showed that Nb₂O₅ nanospheres were tightly and uniformly grown on the surface of SMG nanosheets. Nb₂O₅ nanospheres/SMG composites exhibited an impressive reversible capacity of 404.6 mA h g⁻¹ at the current density of 40 mA g⁻¹ after 100 cycles, and an excellent rate capacity of 345.5 mA h g⁻¹ at the current density of 400 mA g⁻¹.     

Investigation of Li5Cr7Ti6O25 as novel anode material for high-power lithium-ion batteries

In this work, Li₅Cr₇Ti₆O₂₅ as a new anode material for rechargeable batteries is fabricated through a simple sol-gel method at different calcination temperatures. The X-ray diffraction, scanning electron microscopy, high resolution transmission electron microscopy, charge/discharge curve and cyclic voltammograms are utilized to study the crystal structures, morphologies and electrochemical properties of as-obtained Li₅Cr₇Ti₆O₂₅ samples. The impact of calcination temperatures on morphologies and electrochemical properties of Li₅Cr₇Ti₆O₂₅ is discussed in detail. The test result shows that the 800 °C is a proper calcination temperature for Li₅Cr₇Ti₆O₂₅ with excellent electrochemical properties. Cycled at 200 mA g⁻¹, it displays a high initial reversible capacity of 146.6 mA h g⁻¹ and retains a considerable capacity of 130.8 mA h g⁻¹ after 300 cycles. Even cycled at large current density of 500 mA g⁻¹, the initial reversible capacity of 129.6 mA h g⁻¹ with the capacity retention of 88% after 300 cycles is achieved, which is obviously higher than that of Li₅Cr₇Ti₆O₂₅ prepared at 700 °C (80.5 mA h g⁻¹ and 68%) and 900 °C (98.4 mA h g⁻¹ and 80%). In addition, in-situ XRD analysis reveals that Li₅Cr₇Ti₆O₂₅ exhibits a reversible structural change during lithiation and delithiation processes. The above prominent electrochemical performance indicates the great potential of the Li₅Cr₇Ti₆O₂₅ obtained at 800 °C as anode material for rechargeable batteries.     

3D NiCo2S4 nanorod arrays as electrode materials for electrochemical energy storage application

It is essential to develop new electrode materials for electrochemical energy storage to meet the increasing energy demands, reduce environmental pollution and develop low-carbon economy. In this work, binder-free NiCo₂S₄ nanorod arrays (NCS NRAs) on nickel foam electrodes are prepared by an easy and low energy-consuming route. The electrodes exhibit superior electrochemical properties both for alkaline and Li-ion batteries. In 3 M KOH electrolyte, the NCS NRAs achieve a specific capacity of 240.5 mA h g⁻¹ at a current density of 0.2 A g⁻¹, and 105.7 mA h g⁻¹ after 1500 cycles at the current density of 5 A g⁻¹ with capacity retention of 87.3%. As the anode for LIBs, it shows a high initial capacity of 1760.7 mA h g⁻¹ at the current density of 100 mA g⁻¹, corresponding coulombic efficiency of 87.6%, and a rate capacity of 945 mA h g⁻¹ when the current density is improved 10 times. Hence, the NiCo₂S₄ nanorod arrays are promised as electrode materials with competitive performance.     

Carbon-coated SiO/ZrO2 composites as anode materials for lithium-ion batteries

A combination of high-energy ball milling and constant pressure chemical vapor deposition was used to prepare carbon-coated SiO/ZrO₂ composites. It was found that the as-prepared composites were composed of amorphous carbon, amorphous SiO, and paracryslalline ZrO₂. The electrochemical analysis results revealed excellent electrochemical performances for the composites, including a high initial discharge capacity (1737 mA h g⁻¹), a remarkable cyclic stability (reversible capacity of 721 mA h g⁻¹ at 800 mA g⁻¹, after 100 cycles), and a good rate capability (870 mA h g⁻¹ at 800 mA g⁻¹). These features demonstrate that these composites are promising alternative candidates for high-efficiency electrode materials of Li-ion batteries.     

Synthesis and electrochemical performance of Li4Ti5O12 submicrospheres coated with TiN as anode materials for lithium-ion battery

The TiN coated Li₄Ti₅O₁₂ (LTO) submicrospheres with high electrochemical performance as anode materials for lithium-ion battery were synthesized successfully by solvothermal method and subsequent nitridation process in the presence of ammonia. The XRD results revealed that the crystal structure of LTO did not change after thermal nitridation process. The submicrospheres morphology of LTO and TiN film on the surface of LTO submicrospheres were characterized by FESEM and HRTEM, respectively. XPS result confirmed that a small amount of Ti changed from Ti⁴⁺ to Ti³⁺ after nitridation process, which will increase the electronic conductivity of LTO. Electrochemical results showed that electrochemical performance of TiN coated LTO anode materials compared favorably with that of pure LTO. Also its rate capability and cycling performance were apparently superior to those of pure LTO. The reversible capacity of TiN-LTO is 105.2 mA h g⁻¹ at a current density of 10 C after 100 cycles and maintain 92.9% of its initial discharge capacity, while that of pure LTO is only 83.6 mA h g⁻¹ with a capacity retention of 90.3%. Even at 20 C, the discharge capacity of TiN coated LTO sample is 101.3 mA h g⁻¹, compared with 77.3 mA h g⁻¹ for pristine LTO in the potential range 1.0–2.5 V (vs. Li/Li⁺).     

One-step microwave-assisted synthesis of Sb2O3/reduced graphene oxide composites as advanced anode materials for sodium-ion batteries

Sb₂O₃/reduced graphene oxide (RGO) composites were prepared through a facile microwave-assisted reduction of graphite oxide in SbCl₃ precursor solution, and investigated as anode material for sodium-ion batteries (SIBs). The experimental results show that a maximum specific capacity of 503 mA h g⁻¹ is achieved after 50 galvanostatic charge/discharge cycles at a current density of 100 mA g⁻¹ by optimizing the RGO content in the composites and an excellent rate performance is also obtained due to the synergistic effect between Sb₂O₃ and RGO. The high capacity, superior rate capability and excellent cycling performance of Sb₂O₃/RGO composites demonstrate their excellent sodium-ion storage ability and show their great potential as electrode materials for SIBs.     

Investigation on performances of Li1.2Co0.4Mn0.4O2 prepared by self-combustion reaction as stable cathode for lithium-ion batteries

Poor rate capability and cycling performance are the major barriers for Li-rich layered cathode materials to be applied as the next generation cathode materials for lithium-ion batteries. In our work, Li_1.2Co_0.4Mn_0.4O₂ has been successfully synthesized via a self-combustion reaction (SCR) and a calcination procedure. Compared with the material produced by the solid state method (SSM), the one by SCR exhibits both better rate capability and cycling performance. Its initial discharge capacity is 166.01 mA h g⁻¹ with the capacity retention of 85.98% after 50 cycles at a current density of 200 mA h g⁻¹. Its remarkable performance is attributed to a thin carbon coating layer, which not only slows down the transformation rate of layered to spinel structure, but provides a good electronic pathway to increase the Li⁺ diffusion coefficient.     

Preparation and characterization of SrLi2Ti6O14@C/Ag as lithium storage anode material for rechargeable batteries

In this work, silver and carbon co-coated SrLi₂Ti₆O₁₄ is synthesized by using a solid-state assisted solution method, with glucose as carbon source and silver nitrate as Ag source. The structural and morphological properties of as-prepared samples are characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), which confirm that C/Ag composite layer is uniformly coated on the surface of SrLi₂Ti₆O₁₄. Electrochemical measurements like galvanostatic charge/discharge tests, rate performance, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) analysis are also undertaken to evaluate and compare the lithium storage capability of SrLi₂Ti₆O₁₄ before and after coating. According to the results, SrLi₂Ti₆O₁₄@C/Ag presents enhanced electrochemical capability compared with bare material. It can be found that bare SrLi₂Ti₆O₁₄ only delivers the reversible capacity of 140.32 mA h g⁻¹ with capacity retention of 90.7% at 100 mA g⁻¹ after 200 cycles. In contrast, SrLi₂Ti₆O₁₄@C/Ag presents the reversible capacity of 151.20 mA h g⁻¹ with only 6.7% capacity loss after 200 cycles. The improvement is owing to the increase of electronic conductivity and the decrease in the redox polarization after coating. In order to further investigate the structural stability of SrLi₂Ti₆O₁₄@C/Ag, in-situ XRD was performed as well. All the results prove that the C/Ag co-coating has positive effect on the electrochemical performance of SrLi₂Ti₆O₁₄.     

Effect of Fe-doping followed by C+SiO2 hybrid layer coating on Li3V2(PO4)3 cathode material for lithium-ion batteries

A novel Li₃V₂(PO₄)₃ composite modified with Fe-doping followed by C+SiO₂ hybrid layer coating (LVFP/C-Si) is successfully synthesized via an ultrasonic-assisted solid-state method, and characterized by XRD, XPS, TEM, galvanostatic charge/discharge measurements, CV and EIS. This LVFP/C-Si electrode shows a significantly improved electrochemical performance. It presents an initial discharge capacity as high as 170.8 mA h g⁻¹ at 1 C, and even delivers an excellent initial capacity of 153.6 mA h g⁻¹ with capacity retention of 82.3% after 100 cycles at 5 C. The results demonstrate that this novel modification with doping followed by hybrid layer coating is an ideal design to obtain both high capacity and long cycle performance for Li₃V₂(PO₄)₃ and other polyanion cathode materials in lithium ion batteries.     

Carbon coated porous tin peroxide/carbon composite electrode for lithium-ion batteries with excellent electrochemical properties

A porous tin peroxide/carbon (SnO₂/C) composite electrode coated with an amorphous carbon layer is prepared using a facile method. In this electrode, spherical graphite particles act as supporter of electrode framework, and the interspace among particles is filled with porous amorphous carbon derived from decomposition of polyvinylidene fluoride and polyacrylonitrile. SnO₂ nanoparticles are uniformly embedded in the porous amorphous carbon matrix. The pores in amorphous carbon matrix are able to buffer the huge volume expansion of SnO₂ during charge/discharge cycling, and the carbon framework can prevent the SnO₂ particles from pulverization and re-aggregation. The carbon coating layer on the outermost surface of electrode can further prevent porous SnO₂/C electrode from contacting with electrolyte directly. As a result, the repeated formation of solid electrolyte interface is avoided and the cycling stability of electrode is improved. The obtained SnO₂/C electrode presents an initial coulombic efficiency of 77.3% and a reversible capacity of 742 mA h g⁻¹ after 130 cycles at a current density of 100 mA g⁻¹. Furthermore, a reversible capacity of 679 mA h g⁻¹ is obtained at 1 A g⁻¹.     

Hollow core–shell ZnMn2O4 microspheres as a high-performance anode material for lithium-ion batteries

The hollow core–shell ZnMn₂O₄ microspheres are successfully prepared by a solvothermal carbon templating method and then a annealing process. The crystal phase and particle morphology of resultant ZnMn₂O₄ microspheres are characterized by XRD and TEM. The electrochemical properties of the ZnMn₂O₄ microspheres as an anode material are investigated for lithium ion batteries. The results show that the ZnMn₂O₄ microspheres exhibit a reversible capacity of 855.8 mA h g⁻¹ at a current density of 200 mA g⁻¹ after 50 cycles. Even at 1000 mA g⁻¹, the reversible capacity of the ZnMn₂O₄ microspheres is still kept at 724.4 mA h g⁻¹ after 60 cycles. The enhanced electrochemical performance suggests the promising potential of the hollow core–shell ZnMn₂O₄ microspheres in lithium-ion batteries.     

Zn2+ doped TiO2/C with enhanced sodium-ion storage properties

To improve the performance of anatase TiO₂ as an anode material for sodium-ion batteries, Zn²⁺-doped TiO₂/C composites are synthesized by a co-precipitation method. The results of XRD, EPR and XPS demonstrate that Zn²⁺ occupies at the Ti⁴⁺ site of TiO₂ to form a solid-solution, resulting in an expansion of lattice and an increase of Ti³⁺ content. The expansion of lattice can enhance the stability of the crystal structure of TiO₂. The increase of Ti³⁺ content can improve the conductivity of TiO₂. Therefore, Ti_0.94Zn_0.06O₂/C delivers a reversible capacity of 160 mA h g⁻¹ with a capacity retention of 96% after 100 cycles at 5 C. Even charged/discharged at 10 C, this sample still exhibits a reversible capacity of 117 mA h g⁻¹, comparing to 86 mA h g⁻¹ for TiO₂/C. The enhanced electrochemical performances can be ascribed to the improvement of the conductivity and the structural stability of TiO₂ due to Zn²⁺-doping. Therefore, Ti_0.94Zn_0.06O₂/C is an attractive anode material of sodium-ion batteries.     

Hydrazine hydrate-induced hydrothermal synthesis of MnFe2O4 nanoparticles dispersed on graphene as high-performance anode material for lithium ion batteries

Herein, a MnFe₂O₄/graphene (MnFe₂O₄/G) nanocomposite has been synthesized via a facile N₂H₄·H₂O-induced hydrothermal method. During the synthesis, N₂H₄·H₂O is employed to not only reduce graphene oxide to graphene, but also prevent the oxidation of Mn²⁺ in alkaline aqueous solution, thus ensuring the formation of MnFe₂O₄/G. Moreover, MnFe₂O₄ nanoparticles (5–20 nm) are uniformly anchored on graphene. MnFe₂O₄/G electrode delivers a large reversible capacity of 768 mA h g⁻¹ at 1 A g⁻¹ after 200 cycles and high rate capability of 517 mA h g⁻¹ at 5 A g⁻¹. MnFe₂O₄/G holds great promise as anode material in practical applications due to the outstanding electrochemical performance combined with the facile synthesis strategy.     

Electrochemical presodiation promoting lithium storage performance of Mo-based anode materials

Stabilizing the layer structures of Mo-based anode materials is still a challenge for Li ion batteries. Herein, we proposed an electrochemical presodiation strategy for MoS₂ and MoO₃ to improve their cycling stability. It is interesting to note that the cycling stability of as-treated MoS₂ and MoO₃ was significantly improved. Although the reversible discharge capacity was slightly decreased, the capacity of the pretreated MoS₂ at 300 mA g⁻¹ was retained at 345 mA h g⁻¹ after 100 cycles while that of the pristine one decreased to 151 mA h g⁻¹. The capacity of the pretreated MoO₃ after 60 cycles was also improved from 275 mA h g⁻¹ (the pristine one) to 460 mA h g⁻¹. The stabilizing effect was further verified by scanning electron microscope (SEM) analysis. Electrochemical presodiation here could be a promising modification strategy for Mo-based anode materials.     

Synthesis and electrochemical performance of reduced graphene oxide/maghemite composite anode for lithium ion batteries

Reduced graphene oxide (rGO) tethered with maghemite (γ-Fe₂O₃) was synthesized using a novel modified sol–gel process, where sodium dodecylbenzenesulfonate was introduced into the suspension to prevent the undesirable formation of an iron oxide 3D network. Thus, nearly monodispersed and homogeneously distributed γ-Fe₂O₃ magnetic nanoparticles could be obtained on surface of graphene sheets. The utilized thermal treatment process did not require a reducing agent for reduction of graphene oxide. The morphology and structure of the composites were investigated using various characterization techniques. As-prepared rGO/Fe₂O₃ composites were utilized as anodes for half lithium ion cells. The 40 wt.%-rGO/Fe₂O₃ composite exhibited high reversible capacity of 690 mA h g⁻¹ at current density of 500 mA g⁻¹ and good stability for over 100 cycles, in contrast with that of the pure-Fe₂O₃ nanoparticles which demonstrated rapid degradation to 224 mA h g⁻¹ after 50 cycles. Furthermore, the composite showed good rate capability of 280 mA h g⁻¹ at 10C (∼10,000 mA g⁻¹). These characteristics could be mainly attributed to both the use of an effective binder, poly(acrylic acid) (PAA), and the specific hybrid structures that prevent agglomeration of nanoparticles and provide buffering spaces needed for volume changes of nanoparticles during insertion/extraction of Li ions.