Optical absorption and emission properties of Er doped mixed alkali borosilicate glasses

This paper presents the optical absorption and luminescence properties of Er³⁺ doped mixed alkali borosilicate glasses: 59.5SiO₂ · 20B₂O₃ · xLi₂O · (20 − x)Na₂O · 0.5Er₂O₃ and 59.5SiO₂ · 20B₂O₃ · xLi₂O · (20 − x)K₂O · 0.5Er₂O₃, with x = 0, 4, 8, 12, 16 and 20 mol%. The variations of Judd–Ofelt intensity parameters (Ω₂, Ω₄, and Ω₆), hypersensitive transition intensities, total radiative transition probability (A_T), radiative lifetimes (τ_R), integrated absorption cross-sections (Σ) and stimulated emission cross-sections (σ_p) as a function of x are discussed in detail. The changes in Ω₂ and intensities of hypersensitive transitions are attributed to optical basicity changes in the host glass matrix, which leads to variations in the covalency of the Er–O bond. The luminescence properties are reported for certain transitions, and the emission cross-section is high at x = 8–12 in the case of lithium sodium glass, whereas in lithium potassium glass it is high at x = 8.     

Crystal structure and characterization of [2,5-(CH3O)2C6H3NH3]4P4O12·2H2O

The preparation, crystal structure, TG–DTA analysis and spectroscopy investigation are reported for the 2,5-dimethoxy phenyl ammonium cyclotetraphosphate dihydrate [2,5-(CH₃O)₂C₆H₃NH₃]₄P₄O₁₂·2H₂O. This new compound is triclinic P with unit cell dimensions: a = 7.438(5) Å, b = 11.841(7) Å, c = 12.354(4) Å,  = 96.61(4)°, β = 98.35(4)°, γ = 102.60(6)°, Z = 1 and V = 1038.0(1) Å³. Its crystal structure has been determined and refined to R = 0.049, with 5128 independant reflections. The structure can be described by rows of P₄O₁₂ ring anions along the a axis; between these rows are located the organic groups, connected to them by hydrogen bonds.     

Crystal structure and spectroscopic studies of NaGd(PO3)4

Single crystals of gadolinium–sodium polyphosphate NaGd(PO₃)₄ were grown for the first time using a flux method and characterized by X-ray diffraction. This phosphate crystallizes in a monoclinic system with P2₁/n space group and with the following unit-cell dimensions: a = 9.767(3) Å, b = 13.017(1) Å, c = 7.160(2) Å, β = 90.564(5)°, V = 910.3(4) Å³ and Z = 4. The crystal structure was solved from 3451 X-ray independent reflections with final R(F²) = 0.0219 and R_w(F²) = 0.056 refined with 164 parameters (). The atomic arrangement can be described as a long chain polyphosphate organization. Two infinite (PO₃)∝ chains with a period of eight tetrahedra run along the [0 1 1] direction. The structure of NaGd(PO₃)₄ consists of GdO₈ polyhedra sharing oxygen atoms with phosphoric group PO₄. Each Na⁺ ion is bonded to eight oxygen atoms.     

Synthesis, structure refinement and characterization of tetrahydrated acid gadolinium diphosphate HGdP2O7·4H2O

Synthesis and single crystal structure are reported for a new gadolinium acid diphosphate tetrahydrate HGdP₂O₇·4H₂O. This salt crystallizes in the monoclinic system, space group P2₁/n, with the following unit-cell parameters: a = 6.6137(2) Å, b = 11.4954(4) Å, c = 11.377(4) Å, β = 87.53(2)° and Z = 4. Its crystal structure was refined to R = 0.0333 using 1783 reflections. The corresponding atomic arrangement can be described as an alternation of corrugated layers of monohydrogendiphosphate groups and GdO₈ polyhedra parallel to the () plane. The cohesion between the different diphosphoric groups is provided by strong hydrogen bonding involving the W4 water molecule.

IR and Raman spectra of HGdP₂O₇·4H₂O confirm the existence of the characteristic bands of diphosphate group in 980–700 cm⁻¹ area. The IR spectrum reveals also the characteristic bands of water molecules vibration (3600–3230 cm⁻¹) and acidic hydrogen ones (2340 cm⁻¹). TG and DTA investigations show that the dehydration of this salt occurs between 79 and 900 °C. It decomposes after dehydration into an amorphous phase. Gadolinium diphosphate Gd₄(P₂O₇)₃ was obtained by heating HGdP₂O₇·4H₂O in a static air furnace at 850 °C for 48 h.     

Orientation-dependent mobilities from analyses of two-dimensional TiN(111) island decay kinetics

We present a method for the determination of orientation-dependent mobilities Γ_eff(φ) based upon analyses of the detachment-limited coarsening/decay kinetics of equilibrium-shaped two-dimensional islands. An exact analytical expression relating the orientation-dependence of Γ_eff(φ) to that of the anisotropic step energies β(φ) is derived. This provides relative values of Γ_eff(φ) to within an orientation-independent scale factor that is proportional to the decay rate of the island area. Using in situ high temperature (T = 1550–1700 K) low-energy electron microscopy measurements of two-dimensional TiN island coarsening/decay kinetics on TiN(111) terraces for which β(φ) values are known [Phys. Rev. B 67 (2003) 35409], we demonstrate the applicability of our analytic formulation for the determination of absolute Γ_eff(φ) values.     

Synthesis and crystal structure of [2-NH2-5-CH3C5H4N]4P4O12·6H2O

Chemical preparation, crystal structure, IR absorption and thermal analysis of a new cyclotetraphosphate [2-NH₂-5-CH₃C₅H₄N]₄P₄O₁₂·6H₂O are reported. This compound is triclinic P-1 with unit-cell parameters: a = 10.206(5), b = 11.778(1), c = 9.991(4) Å,  = 110.40(6), β = 117.74(6), γ = 86.41(3)°, V = 989.1(8) Å³, Z = 1, D_x = 1.445 g cm⁻³. The structure has been determined and refined to R = 0.034 and R_w = 0.044, using 3663 independent reflections. The ring anions and water molecules form layers spreading around (a, b + c) planes via OHO hydrogen bonds. Between them are anchored 2-amino-5-methylpyridium cations, which establish H-bonds to interconnect the different adjacent layers and so contribute to the cohesion of the three-dimensional network. Tautomerization of (C₆H₉N₂)⁺ groups was evidenced in the present structure.     

Crystal data and indirect optical transitions in Tl2InGaSe4 crystals

The room temperature crystal data and the optical properties of the Bridgman method grown Tl₂InGaSe₄ crystals are reported and discussed. The X-ray diffraction technique has revealed that Tl₂InGaSe₄ is a single phase crystal of monoclinic structure. The unit cell lattice parameters, which were recalculated from the X-ray data, are found to be a = 0.77244 nm, b = 0.64945 nm, c = 0.92205 nm and β = 95.03°. The temperature dependence of the optical band gap of Tl₂InGaSe₄ single crystal in the temperature region of 290–500 K has also been investigated. The absorption coefficient was calculated from the transmittance and reflectance data in the incident photon energy range of 1.60–2.10 eV. The absorption edge is observed to shift toward lower energy values as temperature increases. The fundamental absorption edge corresponds to indirect allowed transition energy gap of 1.86 eV that exhibited a temperature coefficient γ = −3.53 × 10⁻⁴ eV/K.     

Grain boundary statistics in nano-structured iron produced by high pressure torsion

The microstructure and the spectrum of grain boundary misorientations were studied in Armco iron, following high pressure torsion (HPT) deformation, by means of transmission electron microscopy (TEM) and orientation imaging microscopy (OIM). It was found that HPT deformation results in the formation of an equiaxed grain structure with a mean grain size of 270 and 130 nm using a shear strain of γ = 210 and 420, respectively. The misorientation spectra in HPT iron have a bimodal character with maxima in low (at 1–2°) as well as in high misorientation angle ranges. A marked increase in the fraction of special boundaries (Σ3–Σ45) was revealed as a result of HPT. The microstructural changes due to HPT are discussed and compared with those obtained during conventional deformation modes.     

Optical properties of Nd:NaLa (WO4)2 single crystal

Nd³⁺-doped NaLa(WO₄)₂ single crystal with a dimension of 20 mm × 40 mm and a good optical quality was grown by Czochralski method. The polarized absorption spectra and emission spectra were measured at room temperature. The absorption cross-section and emission cross-section were presented. The Judd–Ofelt theory, extended to anisotropic system, has been applied to evaluate the intensity parameters Ω_t (t = 2, 4, 6), radiative transition rates A, radiative lifetimes τ_R and fluorescent branching ratios β. The calculated radiative lifetime was compared with the experiment data for the ⁴F_3/2 emitting level. All spectral features are strongly affected by an inhomogeneous broadening connected with the ‘disordered crystal’ character of the title compound.     

Ultraviolet emitting (Y1−xGdx)2O3−δ thin films deposited by radio frequency magnetron sputtering: Combinatorial modeling, synthesis, and rapid characterization

Gadolinium-doped, yttrium oxide thin films have been deposited on silicon (001) substrates by radio-frequency (RF) magnetron reactive sputtering that exhibit cathodoluminescence (CL) at ultraviolet frequencies. The maximum CL brightness occurred at λ314–315 nm characteristic of the ⁶P_3 / 2 → ⁸S (λ = 314 nm) transition observed in Gd-doped, yttrium oxide powders. The radiative recombination takes place at the rare earth activator Gd³⁺ site embedded in the Y₂O_3−δ host; the optical transition resides within the band gap of the Y₂O_3−δ host and the transition observed is characteristic of atomic gadolinium. A combinatorial approach to sputtering was used to deposit a film of variable composition from 1 to 23 at.% Gd in Y₂O_3−δ in order to rapidly discern the composition node of optimal CL brightness. A simulation was created for the purpose of predicting the film combinatorial composition for binary and ternary alloys prior to sputtering experiments in order to facilitate our combinatorial thin film synthesis technique. The model prediction varied from the real experimental composition profile by only 2.2 at.% Gd ± 1.6 at.% proving the predictor as a useful aide to complement combinatorial thin film experiments. A film of composition Y_1.56Gd_0.44O_3.25 (8.3 at.% Gd) yielded the maximum CL brightness. CL brightness increased continuously up to the 8.3 at.% Gd composition due to the increased number of activators present in the host. Beyond this composition the brightness drastically decreased. The oxygen composition in the combinatorial film was strongly dependent on the Gd composition; films were sub-stoichiometric δ > 0 below 6 at.% Gd and was over-stoichiometric δ < 0 beyond this composition.     

Spectroscopic properties of Yb in heavy metal contained fluorophosphate glasses

A new series of 20Bi(PO₃)₃–10Sr(PO₃)₂–35BaF₂–35MgF₂ doped with Yb³⁺ is introduced for fiber and waveguide laser applications. The stimulated emission cross-section σ_emi, which was found to be 1.37 pm² at the lasing wavelength of 996 nm, is the highest one among fluorophosphate glasses. It has been found that an extremely high gain coefficient of G = 1.65 ms pm⁴ and high quantum efficiency of η = 93% for 1 wt.% Yb₂O₃ doped systems. The various concentration effects on laser performance properties including minimum pumping intensity I_min, the minimum fraction of excited ions β_min and the saturation pumping intensity I_sat are analyzed as a function of Yb₂O₃ concentration. Those results obtained in current system had advantage over some fluorophosphate glasses reported.     

Piezoelectric and dielectric properties of PZT–PZN–PMS ceramics prepared by molten salt synthesis method

Piezoelectric powders and ceramics with the composition of Pb_0.95Sr_0.05(Zr_0.52Ti_0.48)O₃–Pb(Zn_1/3Nb_2/3)O₃–Pb(Mn_1/3Sb_2/3)O₃ (PZT–PZN–PMS) were prepared by molten salt synthesis (MSS) and conventional mixed-oxide (CMO) methods, respectively. The influence of synthesis process on the properties of powders and ceramics were investigated in detail. The results show that the MSS method significantly improved the sinterability of PZT–PZN–PMS ceramics, resulting in an improvement of dielectric and piezoelectric properties compared to the CMO method. The optimum values of MSS samples are as follows: _r = 1773; tan δ = 0.0040; T_c = 280 °C; d₃₃ = 455 pC/N; k_p = 0.70; Q_m = 888; E_c = 10.3 kV/cm; and P_r = 28.2 μC/cm², at calcination of 800 °C and sintering of 1120 °C temperature.     

The effect of heat treatment on the microstructure stability of modified 316LN stainless steel

As a conduit-sheath material for Cu–Nb–Sn wires, chemically modified 316LN steel is subjected to the same reaction heat treatment (100 h at 700 °C) used in transforming the wires into superconducting composite wires. In spite of the long annealing time at 700 °C, there was little or no change in the strength of the steel. A systematic study of the material annealed for 1, 10, 20, 50 and 100 h using orientation imaging microscopy (OIM) showed that with the exception of grain boundary precipitation at t = 100 h, the grain size and grain boundary character were stable. Our results show that twin boundaries (Σ3, Σ9, and Σ27) accounted for about 50% of the total boundaries in all the material conditions studied, suggestive that the density of twins had reached a limit. The stability of the material in spite of the prolonged heat treatment was attributed to the attainment of this maximum twin density in the as-received condition. In view of the high percentage of the twin boundaries in the microstructure, a comprehensive Hall–Petch relationship, which incorporates the contribution of the chemistry, grain size as well as twin boundaries to strengthening was developed. This upper bound theoretical strength compared favorably with the experimental value at 4 K.     

Effect of ferroic domain pattern changes on the Raman spectra of some ferroic crystals

The influence of changes in the pattern of ferroic domain structure on the Raman spectra of β-LiNH₄SO₄ and (NH₄)₃H(SO₄)₂ single crystals were studied. It was shown that the Raman spectra of β-LiNH₄SO₄ passed from the ferroelastic phase differ from those of “as-grown” crystal and those of the crystal, which was in the paraelectric phase. Significant changes could be observed in the Raman bands related to triply degenerated ν₃ and ν₄ vibrations of the SO₄ tetrahedron. Detailed temperature studies of the Raman spectra of β-LiNH₄SO₄ close to the paraelectric–ferroelectric phase transition, exhibit anomaly of some internal vibrations of SO₄ in the temperature range where a regular large-scale structure is observed. Different types of evolution of the ferroelastic domain structure and temperature behaviour of the donor and acceptor vibrations were shown while heating and cooling the (NH₄)₃H(SO₄)₂ crystal. Different values of temperature hysteresis were found in temperature studies of the ferroelastic domain structure (ΔT_S  3–5 K) and in Raman spectra studies (ΔT_S  12 K). No changes were observed in the pattern of ferroelastic domain structure at the temperature T_II–III  265 K, at which C2/c → P2/n structural phase transition takes place. On the other hand, at T_III–IV  135 K additional domains with W′-type of domain wall orientation were found.     

Dielectric and piezoelectric properties of sol–gel derived Ca doped PbTiO3

Synthesis of Ca doped PbTiO₃ powder by a chemically derived sol–gel process is described. Crystallization characteristics of different compositions Pb_1−xCa_xTiO₃ (PCT) with varying calcium (Ca) content in the range x = 0–0.45 has been investigated by DTA/TGA, X-ray diffraction and scanning electron microscopy. The crystallization temperature is found to decrease with increasing calcium content. X-ray diffraction reveals a tetragonal structure for PCT compositions with x ≤ 0.35, and a cubic structure for x = 0.45. Dielectric properties on sintered ceramics prepared with fine sol–gel derived powders have been measured. The dielectric constant is found to increase with increasing Ca content, and the dielectric loss decreases continuously. Sol–gel derived Pb_1−xCa_xTiO₃ ceramics with x = 0.45 after poling exhibit infinite electromechanical anisotropy (k_t/k_p) with a high d₃₃ = 80 pC/N, ′ = 298 and low dielectric loss (tan δ = 0.0041).     

Synthesis, structure and luminescent properties of Lu(PO3)3

A new structural type of rare earth metaphosphate, Lu(PO₃)₃, was prepared from high-temperature solution, of which the crystal structure was solved in S.G. of Cc (No.9) and Z = 4 with unit cell dimensions of a = 13.972(3) Å, b = 6.6710(13) Å, c = 9.958(2) Å and β = 127.36(3)°. In Lu(PO₃)₃, [LuO₆] octahedra connect with the non-bridging oxygens on (PO₃)_n infinite zigzag chains that extended along c-axis. The VUV and X-ray excited luminescent properties of undoped and Ln³⁺ (Ln = Ce, Eu, Tb) doped samples were examined, from which the optical band gap was estimated to be 8.3 eV. Besides, in the undoped sample a STE emission within 320–480 nm was observed, which probably be related to oxygen defects. However, in the Lu(PO₃)₃:Ce sample the Ce³⁺ emission was weak and STE emission was totally quenched under hard X-ray excitation.     

Effect of beta flecks on mechanical properties of Ti–10V–2Fe–3Al alloy

The effects of beta flecks on tensile properties and low-cycle fatigue life were investigated at room temperature for Ti–10V–2Fe–3Al alloy. It was found that beta flecks had a significant influence on tensile ductility and low-cycle fatigue life. The greater the volume fraction of beta flecks (P_A) or maximum area of beta flecks (S_max), the lower the tensile ductility and low-cycle fatigue life. Extensive scanning electron microscopy (SEM) and light microscopy (LM) observation showed that under tensile load, cracks preferentially nucleated at β grain boundaries of beta flecks, then grew, connected and propagated along grain boundaries to form characteristics of intergranular fracture and quasi-cleavage fracture. While under an alternating load, beta flecks acted as sites for low-cycle fatigue crack nucleation due to inhomogeneous alternating strains between soft GB and aged beta matrix. The presence of beta flecks accelerates both the crack nucleation and early crack propagation.     

Electrochromic properties of nanocrystalline MoO3 thin films

Electrochromic MoO₃ thin films were prepared by a sol–gel spin-coating technique. The spin-coated films were initially amorphous; they were calcined, producing nanocrystalline MoO₃ thin films. The effects of annealing temperatures ranging from 100 °C to 500 °C were investigated. The electrochemical and electrochromic properties of the films were measured by cyclic voltammetry and by in-situ optical transmittance techniques in 1 M LiClO₄/propylene carbonate electrolyte. Experimental results showed that the transmittance of MoO₃ thin films heat-treated at 350 °C varied from 80% to 35% at λ = 550 nm (ΔT =  45%) and from 86% to 21% at λ ≥ 700 nm (ΔT =  65%) after coloration. Films heat-treated at 350 °C exhibited the best electrochromic properties in the present study.     

Dynamics of a thin viscoelastic film on an inclined plane

A theory for two-dimensional long and stationary waves of finite-amplitude on a thin viscoelastic fluid (weakly elastic) layer flowing down an inclined plane is investigated. A set of exact averaged equations for the viscoelastic film flow system is described and linearised stability analysis of the uniform flow is performed using normal-mode formulation and the critical condition for linear instability is obtained. The linearised instability for the permanent wave equation, consistent to the second order in (, – unperturbed film thickness, L – characteristic length) is examined and the eigenvalue properties of the fixed points are classified in various parametric regimes. The possible domains of heteroclinic orbits and the regions of possible nonlinear bifurcations are analysed for different values of viscoelastic parameter Γ. Numerical integration of the permanent wave equation as a third order dynamical system is carried out. While wave transitions in real life involve complex spatio-temporal dynamics and many of these transitions lead to chaotic waves that are not stationary traveling waves, bifurcation of stationary traveling waves has been examined as a preliminary study of the more complex transitions. Different bifurcation scenarios leading to multiple hump solitary waves or leading to chaos are exhibited in the parametric space. The results are compared and contrasted with the Newtonian results. A summary of the bifurcation scenarios in the We versus cot θ/Re plane is obtained for different values of viscoelastic parameter Γ, when Re ≈ 13.33 and Re = 100.     

Influence of Mn doping on microstructure and DC-accelerated aging behaviors of ZnO–V2O5-based varistors

The microstructure, electrical properties, dielectric characteristics, and DC-accelerated aging behavior of the ZnO–V₂O₅–MnO₂ system sintered were investigated for MnO₂ content of 0.0–2.0 mol% by sintering at 900 °C. For all samples, the microstructure of the ZnO–V₂O₅–MnO₂ system consisted of mainly ZnO grain and secondary phase Zn₃(VO₄)₂. The incorporation of MnO₂ to the ZnO–V₂O₅ system was found to restrict the abnormal grain growth of ZnO. The nonlinear properties and stability against DC-accelerated aging stress improved with the increase of MnO₂ content. The ZnO–V₂O₅–MnO₂ system added with MnO₂ content of 2.0 mol% exhibited not only a high nonlinearity, in which the nonlinear coefficient is 27.2 and the leakage current density is 0.17 mA/cm², but also a good stability, in which %ΔE_1 mA = −0.6%, %Δ = −26.1%, and %Δtan δ = +22% for DC-accelerated aging stress of 0.85E_1 mA/85 °C/24 h.