Effects of 1,2‐butadiene on the anionic copolymerization of styrene and 1,3‐butadiene in the presence of polar additives

1,2‐Butadiene is shown to be a chain terminating/transferring agent in butyllithium‐initiated diene polymerization. The influence of 1,2‐butadiene on the anionic copolymerization of 1,3‐butadiene and styrene is investigated using n‐butyllithium as initiator and tetrahydrofuran or N,N,N′,N′‐tetramethylethylenediamine as polar additive. A decrease of copolymerization rate is observed on the addition of 1,2‐butadiene. On introducing 1,2‐butadiene, the number average molecular weight (M_n ) decreases and the molecular weight distribution broadens. The vinyl content of copolymer increases slightly with an increase of 1,2‐butadiene. During the copolymerization, 1,2‐butadiene in the presence of a high ratio of polar additives to n‐butyllithium greatly decreases the copolymerization rate, resulting in a lower value of M_n and a narrower molecular weight distribution than that found for a low ratio of polar additives to n‐butyllithium. This evolution can be explained by the base‐catalyzed isomerization of 1,2‐butadiene to form 1‐butylene in the presence of polar additives. With an increasing amount of 1,2‐butadiene, the vulcanized rubber exhibits an increased rolling resistance and a reduced wet skid resistance owing to the decrease of coupling efficiency. These results further indicate the activity of alkynyllithium derivatives produced by the reaction of alkyllithium and 1‐butyne is less than that of the alkyllithium. Copyright © 2007 Society of Chemical Industry     

均相稀土催化苯乙烯均聚及其与异戊二烯共聚

采用新型稀土催化体系氯代三氟乙酸钕－烷基铝－卤代烃,引发苯乙烯均聚及其与异戊二烯共聚。 催化体系各组分及陈化方式、Ｘ和Ａｌ种及用量,溶剂种类等因素对苯乙烯聚合的影响,并用稀土催化实现了Ｓｔ－Ｉｐ嵌段共聚。用ＩＲ,ＮＭＲ及ＤＳＣ等方法表征了聚合物的结构,合成出的Ｓｔ－Ｉｐ二嵌段共聚物中,Ｉｐ链节以反式－１,４－结构为主,含少量３,４－结构,几科不含顺式－１,４－结构。     

Synthesis,characterization and conformational transitions in copolymers of 2‐(o‐chlorophenyl)‐4‐methylene‐1,3‐dioxolane with vinyl monomers

Copolymers of 2‐(o‐chlorophenyl)‐4‐methylene‐1,3‐dioxolane with methyl methacrylate and styrene were synthesized in benzene at 85 °C in the presence of 2,2′‐azobisisobutyronitrile as initiator. The structure of the resulting copolymers was investigated and a polymerization mechanism was proposed. The intrinsic viscosity of the copolymers in dilute solutions of carbon tetrachloride was determined as a function of temperature and conformational transitions were investigated. Copyright © 2004 Society of Chemical Industry     

Synthesis of high molecular weight copolymer of styrene and butadiene bearing high 1,4‐cis butadiene unit from copolymerization with CpTiCl3/methylaluminoxane catalyst

Copolymerization of styrene (St) and butadiene (Bd) with CpTiCl₃/methylaluminoxane (MAO) catalyst in the presence or absence of chloranil (CA) was investigated. The CpTiCl₃/MAO catalyst showed a high activity for the copolymerization of St with Bd. The 1,4‐cis contents in the Bd units for the copolymerization of St and Bd with the CpTiCl₃/MAO catalyst was observed, and the 1,4‐cis content was optimum at a MAO/Ti mole ratio of around 225. The effect of the polymerization temperature on the copolymerization was noted, as was the effect of the 1,4‐cis microstructure in the Bd units for the copolymerization of St and Bd. The addition of CA to the CpTiCl₃/MAO catalyst was found to influence the molecular weight of the copolymer. The high weight‐average molecular weight copolymer (M_w = ca. 50 × 10⁴) consisting of mainly a 1,4‐cis microstructure of Bd units (1,4‐cis = 80.0%) was obtained from the copolymerization with the CpTiCl₃/MAO catalyst in the presence of CA (CA/Ti mole ratio = 1) at 0°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2942–2946, 2003     

Highly trans‐1,4‐specific polymerization of 1,3‐butadiene catalyzed by [2,6‐bis{(4S)‐ (−)‐isopropyl‐2‐oxazolin‐2‐yl}pyridine] chromium complex activated with modified methylaluminoxane

Chromium complexes with N,N,N‐tridentate ligands, LCrCl₃ (L = 2,6‐bis{(4S)‐(?)‐isopropyl‐2‐oxazolin‐2‐yl}pyridine ( 1 ), 2,2′:6′,2″‐terpyridine ( 2 ), and 4,4′,4″‐tri‐tert‐butyl‐2,2′:6′,2″‐terpyridine ( 3 )), were prepared. The structures of 1 and 2 were determined by X‐ray crystallography. Upon activation with modified methylaluminoxane (MMAO), 1 catalyzed the polymerization of 1,3‐butadiene, while 2 and 3 was inactive. The obtained poly(1,3‐butadiene) obtained with 1 ‐MMAO was found to have completely trans‐1,4 structure. The 1 ‐MMAO system also showed catalytic activity for the polymerization of isoprene to give polyisoprene with trans‐1,4 (68%) and cis‐1,4 (32%) structure. Copyright © 2011 Society of Chemical Industry     

Gas phase polymerization of 1,3‐butadiene with supported neodymium‐based catalyst: Investigation of molecular weight

The gas phase polymerization of 1,3‐butadiene (Bd), with supported catalyst Nd(naph)₃/Al₂Et₃Cl₃/Al(i‐Bu)₃ or/and Al(i‐Bu)₂H, was investigated. The polymerization of Bd with neodymium‐based catalysts yielded cis‐1,4 (97.2–98.9%) polybutadiene with controllable molecular weight (MW varying from 40 to 80 × 10⁴ g mol^?1). The effects of reaction temperature, reaction time, Nd(naph)₃/Al(i‐Bu)₃ molar ratio, and cocatalyst component on the catalytic activity and molecular weight of polymers were examined. It was found that there are two kinds of active sites in the catalyst system, which mainly influenced the MW and molecular weight distribution of polybutadiene. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1945–1949, 2004     

Copolymerization of butadiene with styrene using a rare‐earth metal compound – dialkylmagnesium – halohydrocarbon catalytic system

Copolymerizations of butadiene (Bd) with styrene (St) were carried out with catalytic systems composed of a rare‐earth compound, Mg(n‐Bu)₂ (di‐n‐butyl magnesium) and halohydrocarbon. Of all the rare earth catalysts examined, Nd(P₅₀₇)₃–Mg(n‐Bu)₂–CHCl₃ showed a high activity in the copolymerization under certain conditions: [Bd] = [St] = 1.8 mol l^?1, [Nd] = 6.0 × 10^?3 mol l^?1, Mg/Nd = 10, Cl/Nd = 10 (molar ratio), ageing for 2 h, copolymerization at 50 °C for 6–20 h. The copolymer of butadiene and styrene obtained has a relatively high styrene content (10–30 mol%), cis‐1,4 content in butadiene unit (85–90%), and molecular weight ([η] = 0.8–1 dL g^?1). Monomer reactivity ratios were estimated to be r_Bd = 36 and r_St = 0.36 in the copolymerization. © 2002 Society of Chemical Industry     

Vinyl‐type homo‐ and copolymerization of norbornene catalyzed by bis(phenoxyimine) titanium complex

A ternary catalytic system consisting of a bis(phenoxyimine) titanium complex, triisobutylaluminium and an organoboron compound exhibited high activity in the vinyl‐type homopolymerization of norbornene. The obtained polynorbornene showed a modest molecular weight (M _n ≈ 5 × 10⁴ g mol^?1) and broad molecular weight distribution (polydispersity index ≈ 3.5). A copolymer of norbornene with 1,3‐butadiene was prepared using a binary catalytic system consisting of bis(phenoxyimine) titanium complex and triisobutylaluminium. The norbornene units in the copolymer adopted a vinyl‐type addition structure confirmed using distortionless enhancement by polarization transfer 135 ¹³C NMR microstructure analyses. Polymerization kinetics studies showed that neither monomer feed ratio nor conversion had an effect on the composition of the copolymer backbone which was composed of 55% norbornene units and 45% 1,3‐butadiene units. The essentially constant polymer composition implied an alternating nature of chain propagation. The copolymer exhibited good thermal stability and moderate glass transition temperature (50.9–68.2 °C) with a relatively high molecular weight (M _w = 0.18 × 10–1.31 × 10⁵ g mol^?1), and excellent transparency (maximal transmittance >80%). © 2017 Society of Chemical Industry     

Factorial experimental design for graft copolymerization of styrene and methyl methacrylate onto styrene–butadiene rubber

The graft copolymerization of styrene (ST) and methyl methacrylate (MMA) onto styrene–butadiene rubber (SBR) latex prepared by seeded emulsion polymerization has been studied under various reaction conditions using cumene hydroperoxide redox initiator. The mechanism of graft copolymerization has been investigated. The synthesized graft copolymers were purified and then characterized by proton nuclear magnetic resonance (¹H NMR) analysis. A 2 2 fractional factorial experimental design was applied to study the effects of the process variables such as the amount of initiator and emulsifier, the presence or absence of chain‐transfer agent, ST to MMA ratio, monomer to rubber ratio, and reaction temperature on the grafting efficiency. The analysis of the results from the design showed the sequence of the main effect on the observed response of the grafting of ST and MMA onto SBR and that the amount of chain‐transfer agent had a significant effect. Transmission electron microscopy was used to study the morphology of the graft copolymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2867–2874, 2006     

Polymerization of 1,3‐dienes containing functional groups: 8. Free‐radical polymerization of 2‐triethoxysilyl‐ 1,3‐butadiene

The presence of a bulky substituent at the 2‐position of 1,3‐butadiene derivatives is known to affect the polymerization behavior and microstructure of the resulting polymers. Free‐radical polymerization of 2‐triethoxysilyl‐1,3‐butadiene ( 1 ) was carried out under various conditions, and its polymerization behavior was compared with that of 2‐triethoxymethyl‐ and other silyl‐substituted butadienes. A sticky polymer of high 1,4‐structure ( ) was obtained in moderate yield by 2,2′‐azobisisobutyronitrile (AIBN)‐initiated polymerization. A smaller amount of Diels–Alder dimer was formed compared with the case of other silyl‐substituted butadienes. The rate of polymerization (R_p) was found to be R_p = k[AIBN]^0.5[ 1 ]^1.2, and the overall activation energy for polymerization was determined to be 117 kJ mol^?1. The monomer reactivity ratios in copolymerization with styrene were r ₁ = 2.65 and r_st = 0.26. The glass transition temperature of the polymer of 1 was found to be ?78 °C. Free‐radical polymerization of 1 proceeded smoothly to give the corresponding 1,4‐polydiene. The 1,4‐E content of the polymer was less compared with that of poly(2‐triethoxymethyl‐1,3‐butadiene) and poly(2‐triisopropoxysilyl‐1,3‐butadiene) prepared under similar conditions. Copyright © 2010 Society of Chemical Industry     

Palladium‐Catalyzed Methoxycarbonylation of 1,3‐Butadiene: Catalysis and Mechanistic Studies

The palladium‐catalyzed methoxycarbonylation of 1,3‐butadiene to methyl 3‐pentenoate has been studied. Intermediates of the proposed catalytic cycle were synthesized and the elementary steps of the reaction have been investigated in detail. It is shown that the first step of the catalytic cycle, the formation of crotylpalladium complexes from 1,3‐butadiene, proceeds even at room temperature. Examination of the influence of different reaction parameters on product yield and selectivity demonstrate the importance of chelating phosphine ligands and benzoic acids as additive in order to get good results.     

Synthesis and biodegradability evaluation of 2‐methylene‐1,3‐dioxepane and styrene copolymers

Biodegradable copolymers of 2‐methylene‐1,3‐dioxepane (MDO) and styrene (ST) were synthesized by free‐radical copolymerization using di‐t‐butyl peroxide (DTBP) as the initiator. The copolymers containing ester units were characterized by Fourier transform infrared (FTIR), ¹H‐NMR, and ¹³C‐NMR spectroscopy. Their molecular weight and polydispersity index were determined by gel permeation chromatography (GPC). In vitro enzymatic degradation of poly(MDO‐co‐ST) was performed at 37°C in phosphate buffer solution (PBS, pH = 7.4) in the presence of Pseudomonas lipase or crude enzyme extracted from earthworm. The experiment showed that incorporating ester units into C? C backbone chain of polystyrene would result in a biodegradable copolymer. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1146–1151, 2007     

A Highly Regioselective Preparation of 4‐Chloromethyl‐5‐methyl‐2‐aryl‐1,3‐oxazoles

A facile highly regioselective process is described for the formation of 4‐chloromethyl‐1,3‐oxazoles from 1,3‐oxazole N‐oxide/HCl salts. An explanation is presented for the high regioselectivity in deoxygenation‐chlorination using POCl₃ with HCl salts compared to the corresponding free N‐oxides. The method is quite general and the products are isolated by direct precipitation in all cases studied.     

Performance evaluation of ultra‐rapid‐hardening roller‐compacted concrete with styrene butadiene latex

This study was conducted to evaluate the performance of rapid‐hardening roller‐compacted concrete containing styrene butadiene latex. This material has no slump and is compacted with a roller after being poured. Volume reduction is not a concern and the material has a high initial strength due to the high pressure applied. Latex improves the durability of ultra‐rapid‐hardening cement composites. This study evaluated the performance of an optimum mixture (L) and a mixture with no styrene butadiene latex (NL), which had almost the same workability as the optimum mixture. The L mixture exhibited better performance than the NL mixture in terms of bond strength and chloride ion permeability, as well as resistance to abrasion, repeated freezing and thawing, and scaling. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis of hydroxyl‐terminated copolymer of styrene and 4‐vinylpyridine via nitroxide‐mediated living radical polymerization

The random copolymers of styrene (St) and 4‐vinylpyridine (4‐VP) with hydroxyl end group and low polydispersities were synthesized by nitroxide‐mediated living radical polymerization initiated by azobisisobutyronitrile (AIBN) and 4‐hydroxyl‐2,2,6,6–tetramethylpiperidine‐oxyl (TEMPO‐OH). The experimental results have shown that all synthesized copolymers have narrow molecular weight distribution. The conversion of monomers and the molecular weight of copolymer increased with polymerization time. The copolymerization rate is affected by molar ratios of HTEMPO to AIBN. ¹H‐Nuclear magnetic resonance spectra shows that one end of copolymers was capped by TEMPO‐OH moiety. The use of this method permits the copolymer with hydroxyl chain end and controllable molecular weight and molecular weight distribution. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1842–1847, 2004     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

1,2‐Polymerization of 1,3‐butadiene with Cr(acac)3‐alkylaluminum catalysts

The polymerization of butadiene (Bd) with chromium(III) acetylacetonato [Cr(acac)₃]‐trialkylaluminum (AlR₃) or methylaluminoxane (MAO) catalysts was investigated for the synthesis of 1,2‐poly(Bd). The polymerization of Bd was found to proceed with Cr(acac)₃‐AlR₃ (R‐Me, Et, i‐Bu) catalysts to give poly(Bd) with a high 1,2‐vinyl content, but highly isotactic 1,2‐poly(Bd) was not synthesized. The Cr(acac)₃‐MAO catalyst gave a polymer consisting of low 1,2 units. The effects of the Al/Cr mole ratios on the polymerization of Bd with the Cr(acac)₃‐AlR₃ catalysts were observed. With an increase of Al/Cr mole ratios, the isotactic (mm) content of the polymer increased but the 1,2‐vinyl contents decreased. The effects of the aging time and temperatures of the catalysts on the polymerization of Bd with the Cr(acac)₃‐AlR₃ catalysts were also observed, and the lower polymerization temperature and the prolonged aging time were favored to produce the 1,2‐vinyl structure. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1621–1627, 2000     

Decreasing miscibility with greater heterogeneity in ternary polymer blend: poly(cyclohexyl methacrylate), poly(α‐methyl styrene) and poly(4‐methyl styrene)

A ternary blend system comprising poly(cyclohexyl methacrylate) (PCHMA), poly(α‐methyl styrene) (PαMS) and poly(4‐methyl styrene) (P4MS) was investigated by thermal analysis, optical and scanning electron microscopy. Ternary phase behaviour was compared with the behaviour for the three constituent binary pairs. This study showed that the ternary blends of PCHMA/PαMS/P4MS in most compositions were miscible, with an apparent glass transition temperature (T_g) and distinct cloud‐point transitions, which were located at lower temperatures than their binary counterparts. However, in a closed‐loop range of compositions roughly near the centre of the triangular phase diagram, some ternary blends displayed phase separation with heterogeneity domains of about 1 µm. Therefore, it is properly concluded that ternary PCHMA/PαMS/P4M is partially miscible with a small closed‐loop immisciblity range, even though all the constituent binary pairs are fully miscible. Thermodynamic backgrounds leading to decreased miscibility and greater heterogeneity in a ternary polymer system in comparison with the binary counterparts are discussed. © 2003 Society of Chemical Industry     

Influence of imine‐carbon substituent in 6‐bromo‐2‐iminopyridine‐based cobalt(II) complexes on 1,3‐butadiene polymerization

6‐Bromo‐2‐iminopyridine cobalt(II) complexes bearing different imine‐carbon substituents ( Co1 – Co7 ) were synthesized and subsequently employed for 1,3‐butadiene polymerization. All the complexes were identified using Fourier transform infrared spectra and elemental analysis, and complexes Co1 and Co3 were further characterized using single‐crystal X‐ray diffraction analysis, demonstrating they adopted distorted trigonal bipyramidal and tetrahedral geometries, respectively. Activated by methylaluminoxane, these complexes exhibited high cis‐1,4 selectivity, and the activity was highly dependent on the substituent at the imine‐carbon position of the ligand. Addition of PPh₃ to the polymerization systems could enhance the catalytic activity and simultaneously switched the selectivity from cis‐1,4 to cis‐1,2 manner. On the basis of the obtained results, a plausible mechanism involving the regulation of selectivity and activity is proposed. © 2019 Society of Chemical Industry     

Stereochemical and compositional assignments of trans‐4‐methacryloyloxyazobenzene–methyl methacrylate copolymers by one‐ and two‐dimensional NMR spectroscopy

The microstructure of trans‐4‐methacryloyloxyazobenzene–methyl methacrylate copolymers prepared by solution polymerization process using AIBN as initiator is analyzed by one‐and two‐dimensional spectroscopy. Sequence distribution was calculated from the ¹³C(¹H)‐NMR spectra of the copolymers. Comonomer reactivity ratios were determined using the Kelen–Tudos and the nonlinear error‐in‐variables methods are r_A = 1.14 ± 0.08 and r_M = 0.51 ± 0.03; r_A = 1.13 ± 0.1 and r_M = 0.50 ± 0.04, respectively. The sequence distribution of A‐ and M‐centered triads determined from ¹³C(¹H)‐NMR spectra of copolymer is in good agreement with triad concentration calculated from a statistical model. The 2‐D heteronuclear single‐quantum correlation and correlated spectroscopy (TOCSY) was used to analyze the complex ¹H‐NMR spectrum. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 3016–3025, 1999