Controlled grafting of polymer brushes on poly(vinylidene fluoride) films by surface‐initiated atom transfer radical polymerization

Controlled grafting of well‐defined polymer brushes on the poly(vinylidene fluoride) (PVDF) films was carried out by the surface‐initiated atom transfer radical polymerization (ATRP). Surface‐initiators were immobilized on the PVDF films by surface hydroxylation and esterification of the hydroxyl groups covalently linked to the surface with 2‐bromoisobutyrate bromide. Homopolymer brushes of methyl methacrylate (MMA) and poly(ethylene glycol) monomethacrylate (PEGMA) were prepared by ATRP from the α‐bromoester‐functionalized PVDF surface. The chemical composition of the graft‐functionalized PVDF surfaces was characterized by X‐ray photoelectron spectroscopy (XPS) and attenuated total reflectance (ATR)–FTIR spectroscopy. Kinetics study revealed a linear increase in the graft concentration of PMMA and PEGMA with the reaction time, indicating that the chain growth from the surface was consistent with a “controlled” or “living” process. The “living” chain ends were used as the macroinitiator for the synthesis of diblock copolymer brushes. Water contact angles on PVDF films were reduced by surface grafting of PEGMA and MMA. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3704–3712, 2006     

Preparing polymer brushes on poly(vinylidene fluoride) films by free radical polymerization

Grafting of polymer brushes on the poly(vinylidene fluoride) (PVDF) films was carried out by the surface‐initiated free radical polymerization. Surface‐initiators were immobilized on the PVDF films by surface hydroxylation and esterification of the surface‐tethered hydroxyl groups with 4,4′‐azobis(4‐cyanopentanoic acid) (ACP). Homopolymer brushes of methyl methacrylate (MMA) were prepared by free radical polymerization from the azofunctionalized PVDF surface. The chemical composition and topography of the graft‐functionalized PVDF surfaces were characterized by X‐ray photoelectron spectroscopy (XPS), attenuated total reflectance (ATR) FTIR spectroscopy, and atomic force microscopy (AFM). Kinetics study revealed an exponential increase in the graft concentration of polymer brushes with the reaction time, indicating that the chain growth from the surface was consistence with a chain polymerization. Water contact angles on PVDF films were reduced by surface grafting of MMA. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 857–862, 2006     

Synthesis of fluorinated polymer electrolyte membranes by radiation grafting and atom transfer radical polymerization techniques

A novel polymer electrolyte membrane was synthesized by radiation-induced grafting and consequent atom transfer radical polymerization (ATRP). First, bromine-containing perfluorinated grafts were prepared by radiation grafting of 2-bromotetrafluoroethyl trifluorovinyl ether (BrTFF) into a poly(ethylene-co-tetrafluoroethylene) (ETFE) film. Then, the bromine atoms in the ETFE-g-PBrTFF grafted films were acted as initiators, and the films were treated with Cu(I)-based catalytic system of a CuBr and 2,2′-bipyridyl (bpy) for the ATRP. By adjusting the molar ratio of initiator/CuBr/bpy and the reaction temperature, branched poly(styrene) with a grafting yield of above 100% on the poly(BrTFF) main chains was constructed in ETFE-g-PBrTFF films. Thermal analysis revealed that the perfluorinated poly(BrTFF) main chains were miscible to ETFE, whereas the hydrocarbon poly(styrene) branches were phase-separated from the ETFE-g-PBrTFF film. Sulfonic groups could be further introduced into the poly(styrene) grafts of ETFE-g-PBrTFF-g-PS films with homogeneous distribution in a perpendicular direction to the membrane surface. The resulting membrane with a styrene grafting yield of 15% exhibited higher proton conductivity than commercial Nafion 117 membrane. Likewise, it had better chemical stability than ETFE-g-PSSA membrane prepared by conventional radiation-induced grafting.     

Highly efficient synthesis of cylindrical polymer brushes with various side chains via click grafting-onto approach

Though much attention has been paid to synthesis of cylindrical polymer brushes, it is still not easy to prepare well-defined brushes by a general approach. Herein, well-defined cylindrical polymer brushes with various side chains were synthesized via grafting-onto approach by CuAAC click chemistry. Narrowly dispersed polymer backbones functionalized with azide groups were obtained by post-modification of poly(glycidyl methacrylate) (PGMA) which was prepared by reversible addition-fragmentation chain transfer (RAFT) mediated radical polymerization. The alkyne-terminated side chains, polystyrene, polyacrylates, polymethacrylates and poly(N-alkyl acrylamide)s, were synthesized by RAFT mediated radical polymerization with alkyne-containing chain transfer agents (CTAs). The CuAAC reactions between the backbone and side chain polymers were conducted with an equivalent feed of alkyne-terminated side chains and azide groups under mild conditions. Influences of reaction conditions and chemical composition of polymer side chains on grafting efficiency and molecular weight distribution of the polymer brushes were investigated. It is demonstrated that the side chains of polystyrene, polyacrylates and poly(N-alkyl acylamide)s were grafted at a density above 85% while that of polymethacrylates decreased to ca. 50%. The polymer brushes synthesized under the optimized reaction conditions had well-defined chemical composition and narrow distribution of molecular weight, and their wormlike morphology was visualized by atomic force microscopy (AFM).     

Chemical Functionalization of Graphene Oxide by Poly(styrene sulfonate) Using Atom Transfer Radical and Free Radical Polymerization: A Comparative Study

Poly(sodium styrenesulfonate)-functionalized graphene was prepared from graphene oxide, using atom transfer radical polymerization and free radical polymerization. In atom transfer radical polymerization route, the amine-functionalized GO was synthesized through hydroxyl group reaction of GO with 3-amino propyltriethoxysilane. Atom transfer radical polymerization initiator was grafted onto modified GO (GO-NH₂) by reaction of 2-bromo-2-methylpropionyl bromide with amine groups, then styrene sulfonate monomers were polymerized on the surface of GO sheets by in situ atom transfer radical polymerization. In free radical polymerization route, the poly(sodium 4-styrenesulfonate) chains were grafted on GO sheets in presence of Azobis-Isobutyronitrile as an initiator and styrene sulfonate monomer in water medium. The resulting modified GO was characterized using range of techniques. Thermal gravimetric analysis, scanning electron microscopy, transmission electron microscopy, and atomic force microscopy results indicated the successful graft of polymer chains on GO sheets. Thermogravimetric analysis showed that the amount of grafted polymer was 22.5 and 31?wt% in the free radical polymerization and atom transfer radical polymerization methods, respectively. The thickness of polymer grafted on GO sheets was 2.1?nm (free radical polymerization method) and 6?nm (atom transfer radical polymerization method) that was measured by atomic force microscopy analysis. X-ray diffractometer and transmission electron microscopy indicated that after grafting of poly(sodium 4-styrenesulfonate), the modified GO sheets still retained isolated and exfoliated, and also the dispersibility was enhanced.     

Architecture of colloidal crystals constructed by silica hybrid nanoparticles

Silica (SiO₂)‐crosslinked polystyrene (PS) particles possessing photofunctional N,N‐diethyldithiocarbamate (DC) groups on their surface were prepared by the free‐radical emulsion copolymerization of a mixture of SiO₂ (diameter D_n = 192 nm), styrene, divinyl benzene, 4‐vinylbenzyl N,N‐diethyldithiocarbamate (VBDC), and 2‐hydroxyethyl methacrylate with a radical initiator under UV irradiation. In this copolymerization, the inimer VBDC had the formation of a hyperbranched structure by a living radical mechanism. These particles had DC groups on their surface. Subsequently, poly(methyl methacrylate) brushes encapsulated SiO₂ particles were synthesized by the grafting from a photoinduced atom transfer radical polymerization (ATRP) approach of methyl methacrylate initiated by SiO₂‐crosslinked PS particles as a macroinitiator. We constructed the colloidal crystals using these photofunctional particles. Moreover, the SiO₂ particle array of colloidal crystals was locked by radical photopolymerization with vinyl monomer as a matrix. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Functionalisation of polypropylene by solid phase graft polymerisation and its effect on mechanical properties of silica nanocomposites

Abstract

To prepare macromolecular compatibiliser for grafted nano-SiO₂ /polypropylene (PP) composites, solid phase graft copolymers of PP with styrene and ethyl acrylate were synthesised, respectively. It was found that both per cent grafting and grafting efficiency can be adjusted by changing initiator concentration, reaction temperature and reaction time. As a result of partial chain scission and deterioration of ordered structure of PP during the graft polymerisation, the grafted PP exhibits poorer thermal stability and crystallisability than the unmodified PP. Mechanical tests of grafted nano-SiO₂ /PP composites indicated that the addition of PP copolymer with the same species of grafting polymer as that on the nanoparticles further improves the ductility of the composites. Molecular rigidity of the grafting polymers, presence of the homopolymer produced during the graft polymerisation, and strain rate of the load applied have an important influence on the toughening effect of the functionalised PP.     

Functionalisation of polypropylene by solid phase graft polymerisation and its effect on the mechanical properties of silica nanocomposites

Abstract

To prepare macromolecular compatibiliser for grafted nano-SiO₂/polypropylene (PP) composites, solid phase graft copolymers of PP with styrene and ethyl acrylate were synthesised, respectively. It was found that both percentage grafting and grafting efficiency can be adjusted by changing initiator concentration, reaction temperature and reaction time. Due to partial chain scission and deterioration of the ordered structure of PP during the graft polymerisation, the grafted PP exhibits worse thermal stability and crystallisability than the unmodified PP. Mechanical tests of grafted nano-SiO₂/PP composites indicated that the addition of PP copolymer with the same species of grafting polymer as that on the nanoparticles further improves the ductility of the composites. Molecular rigidity of the grafting polymers, presence of the homopolymer produced during the graft polymerisation, and strain rate of the load applied have important influences on the toughening effect of the functionalised PP.     

Grafting of polyelectrolytes onto polyacrylamide by reactive processing

Low‐molecular‐weight high‐charge‐density cationic poly diallydimethyl ammonium chloride (polyDADMAC) was grafted onto nonionic polyacrylamide (PAM) using organic peroxide initiators in the molten state carried out in a batch mixer. The graft copolymer can be used as a high performance flocculant. Glycerol was selected as a plasticizer. The grafting reaction was characterized in terms of composition, temperature, degree of grafting, and grafting efficiency. It was found that free radicals on polymer chains were induced by the decomposition of the initiator. Grafting was produced by free radical recombination termination. The degree of grafting increases with an increase of the polyDADMAC/PAM feed ratio. However, the grafting efficiency was lower than 10 wt % in this highly viscous polymer melt system. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1412–1416, 1999     

The synthesis of poly(3‐hydroxybutyrate)‐g‐poly(methylmethacrylate) brush type graft copolymers by atom transfer radical polymerization method

Brush type of poly (3‐hydroxy butyrate), PHB, copolymer synthesis has been reported. Natural PHB was chlorinated by passing chlorine gas through PHB solution in CHCl₃/CCl₄ mixture (75/25 v/v) to prepare chlorinated PHB, PHB‐Cl, with the chlorine contents varying between 2.18 and 39.8 wt %. Toluene solution of PHB‐Cl was used in the atom transfer radical polymerization (ATRP) of methyl methacrylate, MMA, in the presence of cuprous bromide (CuBr)/2,2′‐bipyridine complex as catalyst, at 90°C. This “grafting from” technique led to obtain poly (3‐hydroxybutyrate)‐g‐poly(methylmethacrylate) (PHB‐g‐PMMA) brush type graft copolymers (cylindrical brush). The polymer brushes were fractionated by fractional precipitation methods and the γ values calculated from the ratio of the volume of nonsolvent to volume of solvent of brushes were ranged between 2.8 and 9.5 depending on the molecular weight, grafting density, and side chain length of the brushes, while the γ values of PHB, PHB‐Cl, and homo‐PMMA were 2.7–3.8, 0.3–2.4, and 3.0–3.9, respectively. The fractionated brushes were characterized by gel permeation chromatography, ¹H‐NMR spectrometry, thermogravimetric analysis (TGA), and differential scanning calorimetry techniques. PHB‐g‐PMMA brush type graft copolymers showed narrower molecular weight distribution (mostly in range between 1.3 and 2.2) than the PHB‐Cl macroinitiator (1.6–3.5). PHB contents in the brushes were calculated from their TGA thermograms and found to be in range between 22 and 42 mol %. The morphologies of PHB‐g‐PMMA brushes were also studied by scanning electron microscopy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

An effective multipurpose building block for 3D electropolymerisation: 2,2′-Bis(2,2′-bithiophene-5-yl)-3,3′-bithianaphthene

Novel thiophene-based oligomer, 2,2′-bis(2,2′-bithiophene-5-yl)-3,3′-bithianaphthene (TX), was designed and synthesized, and its electrochemical and spectral properties characterised. TX was readily polymerised electrochemically to form well organized conducting homopolymer films on various solid electrode substrates. Moreover, it was successfully used for deposition by electropolymerisation of electrochemically active thin films of co-polymers with three different monomers of functionalised bis(2,2′-bithienyl)methane derivatives. It appeared that TX was an effective crosslinker and 3D promoter in these electropolymerisations involving co-monomers intrinsically showing limited aptitude for the electropolymerisation or forming polymer films of low conductivity. This attractive TX ability stems from combination of its (i) high conjugation efficiency in each of the two planar moieties, (ii) intrinsic 3D structure on account of the presence of the central node, and (iii) intrinsic regioselectivity in electropolymerisation on account of the positions of the two available free α-thiophene sites.     

Comparative investigations of radiation‐grafted proton‐exchange membranes prepared using single‐step and conventional two‐step radiation‐induced grafting methods

Proton‐exchange membranes containing poly(styrene sulfonic acid) grafts hosted in poly(vinylidene fluoride) (PVDF) films were prepared using two radiation‐induced grafting methods: a single‐step grafting method (SSGM) involving grafting of sodium styrene sulfonate onto electron beam (EB)‐irradiated PVDF films and a conventional two‐step grafting method (CTSGM) in which styrene monomer is grafted onto EB‐irradiated PVDF films and subsequently sulfonated. Differential scanning calorimetry, universal mechanical testing and scanning transmission electron microscopy were used to evaluate the thermal, mechanical and structural changes developed in the membranes during the preparation procedures. Physicochemical properties such as water uptake, hydration number and ionic conductivity were studied as functions of ion‐exchange capacity and the results obtained were correlated with the structural changes accompanying each preparation method. Membranes obtained using the SSGM were found to have superior properties compared to their counterparts prepared using the CTSGM suggesting the former method is more effective than the latter for imparting desired functionality and stability properties to the membranes. Copyright © 2010 Society of Chemical Industry     

Dehydrochlorinated poly(vinyl chloride-g-styrene). I. Effect of synthesis conditions

Dehydrochlorinated poly(vinyl chloride) (DHPVC) was graft copolymerized with styrene monomer using benzoyl peroxide (Bz₂O₂) as free radical initiator, in vacuum. The effect of synthesis conditions such as time, initiator concentration, the ratio of monomer to polymer, and temperature on various grafting parameters was studied. On the whole, a maximum of 47 wt % polystyrene (PSt) in the graft (DHPVC-g-PSt) was obtained. PSt contents of graft copolymers determined by gravimetry, chlorine analysis, and UV spectroscopy have been compared. A “grafting from” mechanism has been proposed for the graft copolymerization.     

Preparation and characterization of grafting polyacrylamide from PET films by SI‐ATRP via water‐borne system

The grafted homopolymer and comb‐shaped copolymer of polyacrylamide were prepared by combining the self‐assembly of initiator and water‐borne surface‐initiated atom transfer radical polymerization (SI‐ATRP). The structures, composition, properties, and surface morphology of the modified PET films were characterized by FTIR/ATR, X‐ray photoelectron spectroscopy (XPS), contact angle measurement, and scanning electronic microscopy (SEM). The results show that the surface of PET films was covered by equable grafting polymer layer after grafted polyacrylamide (PAM). The amount of grafting polymer increased linearly with the polymerization time added. The GPC date show that the polymerization in the water‐borne medium at lower temperature (50°C) shows better “living” and control. After modified by comb‐shaped copolymer brushes, the modified PET film was completely covered with the second polymer layer (PAM) and water contact angle decreased to 13.6°. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Controlled Surface Initiated Polymerization of N-Isopropylacrylamide from Polycaprolactone Substrates for Regulating Cell Attachment and Detachment

Poly(ε-caprolactone) (PCL) substrates were modified with thermoresponsive poly(N-isopropylacrylamide) (PNIPAM) brushes to direct and control cellular attachment and detachment. Prior to brush growth, the surface of PCL was activated by a diamine to allow for initiator coupling. Infrared spectra taken before and after cell culturing demonstrated the covalently attached nature of the PNIPAM brushes. PCL is a biocompatible polymer and to prove that the modifications described above did not change this characteristic property, a cell attachment/detachment study was carried out. The modified substrates showed a lower cell attachment when compared to PCL alone and to PCL films modified with the initiator. The possibility to detach the cells in the form of a sheet was proved using PNIPAM-modified PCL films by lowering the temperature to 25 °C. No relevant detachment was shown by the unmodified or by the initiator modified surfaces. This confirmed that the detachment was temperature dependent and not connected to other factors such as polymer swelling. These functionalized polymeric films can find applications as smart cell culture systems in regenerative medicine applications.     

Molecular brushes with extreme grafted side chain densities

A series of densely grafted poly(n-butyl acrylate) (PBA) molecular brushes with four different grafting densities were synthesized by the “grafting-from” approach using atom transfer radical polymerization (ATRP). A novel monomer, isopropylidene-2,2-Bis(methoxy)propionic hydroxyethylmethacrylate (IMPHMA), was synthesized and copolymerized with methyl methacrylate (MMA) under different monomer feed ratios to yield a series of linear poly(methyl methacrylate-stat-IMAPA), [PMMA-s-(PIMPHMA)]. The resulting copolymers were deprotected and transformed to macroinitiators, [PMMA-s-(PHEMA-IMPHMA-Br)]. n-Butyl acrylate (BA) was grafted from these macroinitiators to yield a series of molecular brushes, [PMMA-s-{(PIMPHMA)-g-PBA}], with various side chain lengths. Molecular brushes were characterized by gel permeation chromatography (GPC) and ¹H NMR. PBA side chains were cleaved by acid hydrolysis, and the resulting linear PBA polymers were characterized by GPC to study initiation efficiency during the synthesis of molecular brushes. The initiation efficiency increased with polymerization time and decreased with macroinitiators that had more initiation sites. Atomic force microscopy (AFM) measurements demonstrated the characteristic molecular structure by resolving individual brush molecules.     

Polymerization of vinyl monomers initiated by zwitterionic polymer in aqueous solution

The polymerization of vinyl monomers, mainly styrene and methyl methacrylate, initiated by zwitterionic poly[3-dimethyl(methacryloyloxy-ethyl)ammonium propane sulfonate], [poly(DMAPS)], in aqueous solution was studied under vacuum at 85°C. An initiation mechanism involving hydrogen atom transfer is proposed. The effects of the efficiency of grafting. pH, water content and betaine polymer content on the polymerization were investigated. The conversion of vinyl monomers in poly(DMAPS) is lower than that in poly [3-dimethyl(acryloyloxyethyl)ammonium propane sulfonate], which may be due to steric hindrance of the methyl group on the α-carbon of the former.     

Synthesis and characterization of TiO2 nanoparticles chemically coated with zwitterionic polymer brushes

This study introduces a synthetic method to graft zwitterionic poly (2-methacryroyloxyethyl phosphoryl choline) brushes onto TiO₂ nanoparticles with thickness of a few nanometers. The grafting of zwitterionic polymer brushes was characterized by electron microscope measurements, zeta-potential analysis, and thermo-gravimetric analysis. The technique we employed to synthesize those hybrid nanoparticles was a modified seeded emulsion polymerization in which the polymerization loci were changed in the stage of radical initiation and chain propagation. We have found that the polymerization loci should be on the surface for achieving the effective grafting of polymer brushes. From the suspension rheology studies, we have observed that the suspension of our hybrid nanoparticles was dominated by the attractive force as well as by packing volume effect. This unique rheological behavior is expected to be useful for understanding the inter-particle interactions in complex formulations.     

Grafted stock synthesis of ABS at the ultimate high ratio of polybutadiene to poly(styrene‐co‐acrylonitrile)

This study describes the emulsion grafting of styrene and acrylonitrile onto 60–70% polybutadiene (PB), in the presence or absence of tert‐dodecanetiol as a chain transfer reagent with a radical initiator, and the properties of the obtained grafted stock. There was no significant difference in terms of effect of the initiation mode on the grafting efficiency resulting from the high grafting reactivity of PB. However, the grafted stock with 70% PB prepared in the presence of tert‐dodecanetiol and the adequate selection of an initiation system gave a homogeneous dispersion of the PB particles into poly(styrene‐co‐acrylonitrile) (SAN) matrix. The initiation system involves tert‐butyl peroxylaurate, tert‐butyl peroxyacetate, and tert‐butyl peroxyisopropylcarbonate coupled with ferrous sulfate. The efficient coverage of the SAN grafted layer around 70% PB particles was observed by TEM to eventually give excellent impact resistance, high surface gloss, and good thermal resistance. The absence of tert‐dodecanetiol resulted in a toughness reduction of ABS. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3462–3470, 2001     

Polystyrene Nanospheres Modified with a Hydrophilic Polymer Brush through Subsurface‐Initiated Atom Transfer Radical Polymerization as Biolubricating Additive

Hydration lubrication plays an important role including the cartilage of an organism. Here, polystyrene nanospheres modified with a hydrophilic polymer through subsurface‐initiated grafting as a biolubricating additive is proposed. The material provides good tribological performance when subjected to high load. Compared with surfaced‐initiated grafting polymer brushes, subsurface initiation can form much thicker hydration layers to obtain a lower friction coefficient and better mechanical properties for withstanding prolonged shearing forces with less measurable damage. The polymer brushes penetrate through the covalent network of the polystyrene nanospheres providing a match in mechanical properties between them, so that the additives obtain more excellent lubricity in an aqueous environment under shear pressure, which is expected to become a promising artificial joint biolubricating additive.