α‐cyclodextrin assisted self‐assembly of poly(ethylene glycol)‐block‐poly(N‐isopropylacrylamide) in aqueous media

Poly(ethylene glycol)‐block‐poly(N‐isopropylacrylamide) (PEG‐b‐PNIPAM) block copolymers were synthesized by atom transfer radical polymerization, and the α‐cyclodextrin (α‐CD) induced self‐assembly characteristics of the system were elucidated. Below the lower critical solution temperature (LCST) of PNIPAM, CD threaded onto the PEG segments and induced micellization to form rod‐shaped nanostructures comprising of a PEG/α‐CD condensed phase and a PNIPAM shell. Increasing the temperature of system above the LCST caused the PNIPAM segments to collapse, which resulted in the dethreading of the CD. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Thermo‐responsive polymers for drag reduction in turbulent Taylor–Couette flow

The addition of a small amount of high molecular weight polymer to a solvent can substantially decrease friction losses by approximately 80%. This phenomenon known as drag reduction (DR) is used extensively in oil recovery during hydraulic fracturing and in many other applications to reduce the pumping costs. However, because of long chain length, these polymers get adsorbed on the surface of reservoir, diminishing the effectiveness of fracking. In the current study, a thermo‐responsive polymer, i.e., poly(N‐isopropylacrylamide) (PNIPAM) is investigated as a drag reducing agent (DRA), which collapses reversibly above 33 °C known as lower critical solution temperature (LCST), thereby preventing it from getting adsorbed beyond this temperature. Free radical polymerization was used to synthesize the PNIPAM and a Taylor–Couette (TC) setup with a rotating inner cylinder was utilized for measuring the DR. The effect of concentration, Reynolds number (Re), and temperature on DR were studied and a maximum of 50% DR was observed at 400 PPM concentration. PNIPAM demonstrated significant decrease in DR beyond LCST, validating its thermo‐responsive nature that could be beneficial for DR in oil recovery or in providing a control modality to DR technologies.DR versus temperature for PNIPAM solution (500 PPM) at Re = 100,000 demonstrating responsive behavior with temperature © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44191.     

Self‐assembly and drug delivery behaviors of thermo‐sensitive poly(t‐butyl acrylate)‐b‐poly(N‐isopropylacrylamide) micelles

Self‐assembly of thermo‐sensitive poly (t‐butyl acrylate)‐b‐poly(N‐isopropylacrylamide) (PtBA‐ b‐PNIPAM) micelles in aqueous medium and its applications in controlled release of hydrophobic drugs were described. PtBA‐b‐PNIPAM was synthesized by atom transfer radical polymerization and aggregated into thermo‐sensitive core‐shell micelles with regular spheres in water, which was confirmed by ¹H‐NMR, fluorescence spectroscopy, transmission electron microscopic (TEM), and UV–vis spectroscopic techniques. The critical micelle concentration of micelles decreased with the increase of the hydrophobic components. The anti‐inflammation drug naproxen (NAP) was loaded as the model drug into polymeric micelles, which showed a dramatic thermo‐sensitive fast/slow switching behavior around the lower critical solution temperature (LCST). When the temperature was enhanced above LCST, release of NAP from core‐shell micelles was accelerated ascribed to the temperature‐induced deformation of micelles. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermoresponsive behaviour in aqueous solution of poly(maleic acid‐alt‐vinyl acetate) grafted with poly(N‐isopropylacrylamide)

The synthesis of a thermoresponsive graft copolymer consisting of a maleic acid/vinyl acetate alternating copolymer backbone (MAc‐alt‐VA) and poly(N‐isopropylacrylamide) (PNIPAM) side chains is reported. Turbidimetric measurements in dilute aqueous solutions showed that no macroscopic phase separation takes place when the temperature is raised above the lower critical solution temperature (LCST) of PNIPAM, even at pH = 2. Moreover, in semi‐dilute aqueous solutions, a pronounced thermally induced viscosity increase (thermothickening) was observed. This thermoresponsive behaviour has been attributed to the interconnection of the hydrophilic MAc‐alt‐VA graft copolymer backbones by means of the hydrophobic PNIPAM side chain aggregates formed as the temperature increases above the LCST of this polymer. Copyright © 2004 Society of Chemical Industry     

Gating Characteristics of Thermo‐Responsive Membranes with Grafted Linear and Crosslinked Poly(N‐isopropylacrylamide) Gates

Thermo‐responsive porous membranes with grafted linear and crosslinked poly(N‐isopropylacrylamide) (PNIPAM) gates are successfully prepared at temperatures above and below the lower critical solution temperature (LCST) of PNIPAM by using a plasma‐induced grafting polymerization method, and the effects of operation pressure and grafting temperature on the thermo‐responsive gating characteristics of the prepared membranes are investigated systematically. The fluxes of water through the grafted membranes increase simply with increasing the operation pressure no matter whether the environmental temperature is 40 °C or 25 °C. Under high operation pressure (e.g., higher than 0.14 MPa), the grafted linear PNIPAM gates deform to a certain extent, whereas the grafted crosslinked PNIPAM gates do not deform. For both membranes with grafted linear and crosslinked PNIPAM gates, the membranes prepared at 25 °C (below the LCST of PNIPAM) show larger thermo‐responsive gating coefficients than those prepared at 40 °C (above the LCST of PNIPAM), which results from different distributions of grafted PNIPAM gates in the membrane pores. When the PNIPAM gates are grafted at 25 °C, the grafted layer near the membrane surface is much thicker than that inside the membrane pores; on the other hand, when the PNIPAM gates are grafted at 40 °C, the grafted layer is homogeneously formed throughout the whole pore length. Both linear and crosslinked grafted PNIPAM gates in the membrane pores exhibit stable and repeatable thermo‐responsive “open‐close” switch performances under the operation pressure of 0.26 MPa. The results in this study provide valuable guidance for designing, fabricating, and operating thermo‐responsive gating membranes with desirable performances.     

Light‐triggered reversible solubility of α‐cyclodextrin and azobenzene moiety complexes in PDMAA‐co‐PAPA via molecular recognition

Photoresponsive polymer with azobenzene pendant group (PDMAA‐co‐PAPA) was synthesized by radical polymerization of N,N‐dimethylacrylamide (DMAA) and N‐4‐phenylazophenyl acrylamide (PAPA), and the characterization of the inclusion complexes of the PDMAA‐co‐PAPA with α‐cyclodextrin (α‐CD) were performed by FTIR, GPC, ¹H NMR, 2D NOESY, and UV–vis spectroscopy. It was found that the solubility of PDMAA‐co‐PAPA and α‐CD inclusion complexes in aqueous solution showed tunable property, which could be triggered by alternating UV–vis light irradiation at a certain temperature due to the effect of molecular recognition of α‐CD with azobenzene moiety in the polymer. After UV irradiation, the lower critical solution temperature (LCST) of the polymer aqueous solution increased slightly without α‐CD while the LCST decreased sharply at presence of α‐CD. Furthermore, UV spectroscopy showed that the photoisomerization of the polymer solution went on rapidly and reversibly, and 2D NOESY data suggested that the inclusion complexation of α‐CD with trans azobenzene moiety and the decomplexation with cis azobenzene resulted in reversible solubility behavior when objected to UV and Vis light irradiation alternately. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Hyperbranched homo and thermoresponsive graft copolymers by using ATRP‐macromonomer initiators

Macromonomer initiators behave as macro cross‐linkers, macro initiators, and macromonomers to obtain branched and cross‐linked block/graft copolymers. A series of new macromonomer initiators for atom transfer radical polymerization (MIM‐ATRP) based on polyethylene glycol (M_n = 495D, 2203D, and 4203D) (PEG) were synthesized by the reaction of the hydroxyl end of mono‐methacryloyl polyethylene glycol with 2‐bromo propanoyl chloride, leading to methacryloyl polyethylene glycol 2‐bromo propanoyl ester. Poly (ethylene glycol) functionalized with methacrylate at one end was reacted with 2‐bromopropionyl chloride to form a macromonomeric initiator for ATRP. ATRP was found to be a more controllable polymerization method than conventional free radical polymerization in view of fewer cross‐linked polymers and highly branched polymers produced from macromonomer initiators as well. In another scenario, ATRP of N‐isopropylacrylamide (NIPAM) was initiated by MIM‐ATRP to obtain PEG‐b‐PNIPAM branched block/graft copolymers. Thermal analysis, FTIR, ¹H NMR, TEM, and SEM techniques were used in the characterization of the products. They had a thermo‐responsive character and exhibited volume phase transition at ～ 36°C. A plasticizer effect of PEG in graft copolymers was also observed, indicating a lower glass transition temperature than that of pure PNIPAM. Homo and copolymerization kinetics were also evaluated. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Phase behavior of temperature‐ and pH‐sensitive poly(acrylic acid‐g‐N‐isopropylacrylamide) in dilute aqueous solution

Several different composition temperature‐ and pH‐sensitive poly(acrylic acid‐g‐N‐isopropylacrylamide) (P(AA‐g‐NIPAM)) graft copolymers were synthesized by free‐radical copolymerization utilizing macromonomer technique. The phase behavior and conformation change of P(AA‐g‐NIPAM) in aqueous solutions were investigated by UV–vis transmittance measurements, fluorescence probe, and fluorescence quenching techniques. The results demonstrate that the P(AA‐g‐NIPAM) copolymers have temperature‐ and pH‐sensitivities, and these different composition graft copolymers have different lower critical solution temperature (LCST) and critical phase transition pH values. The LCST of graft copolymer decreases with increasing PNIPAM content, and the critical phase transition pH value increases with increasing Poly(N‐isopropylacrylamide) (PNIPAM) content. At room temperature (20°C), different composition of P(AA‐g‐NIPAM) graft copolymers in dilute aqueous solutions (0.001 wt %) have a loose conformation, and there is no hydrophobic microdomain formation within researching pH range (pH 3 ～ 10). In addition, for the P(AA‐g‐NIPAM) aqueous solutions, transition from coil to globular is an incomplete reversible process in heating and cooling cycles. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermoresponsive self‐assembled nanovesicles based on amphiphilic triblock copolymers and their potential applications as smart drug release carriers

A series of thermoresponsive triblock copolymers, methoxy poly(ethylene oxide)‐b‐poly(ε‐caprolactone)‐b‐poly(N‐isopropylacrylamide) (mPEO‐b‐PCL‐b‐PNIPAM), with different PCL and PNIPAM block lengths, were synthesized by a combination of ring opening polymerization and reversible addition‐fragmentation chain transfer polymerization techniques. The triblock copolymers undergo self‐assembly in aqueous solutions forming stable nanovesicles of various sizes with a lipid membrane structure similar to body cells as revealed by transmission electron microscopy. The nanovesicle is thermoresponsive, that is, its size is tunable using the temperature as a switch: shrinks at a temperature above the lower critical solution temperature (LCST) and expands at a temperature below the LCST. The corresponding LCST of the triblock copolymers is adjustable by varying the PNIAM segment length as well as the PCL segment length and covers a range from 33.9 to 41.0°C in water. The diameter of nanovesicles for mPEO_3k‐b‐PCL_5k‐b‐PNIPAM_13.2k is about 177.7 nm below the LCST and 138.9 nm above the LCST, as determined by dynamic light scattering. It was demonstrated using indomethacin, a popular anti‐inflammation medicine, that the triblock copolymers can effectively act as a drug release carrier under the right human physiological conditions, that is, store the drug at a lower temperature and release it at a higher temperature, possibly targeting at the lesion sites of human body. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41361.     

Multi‐responsive microgel of a water‐soluble monomer via emulsion polymerization

Microgel of a water‐soluble monomer [2‐(N‐morpholino)ethyl methacrylate (MEMA)] was successfully prepared in aqueous media via emulsion polymerization by using a novel water‐soluble block copolymer as stabilizer. Characterization studies confirmed monodisperse spherical morphologies of microgels with a diameter of 280 nm at neutral pH. These microgels exhibited multi‐responsive behavior by responding solution pH, temperature, ionic strength, type of dispersing media, and magnetic particles. It swells well at low pH (<6.0) and at low temperature, but shrinks above pH 6.0, or even more shrinks with salt addition at neutral and basic conditions. In addition, the hydrodynamic diameter of PMEMA microgel was decreased gradually at basic and neutral pH when solution temperature was increased up to the lower critical solution temperature of PMEMA (LCST, 35°C), but microgel diameter did not change much above LCST. Multi‐responsive behavior of PMEMA microgel was investigated by using dynamic light scattering, UV‐Vis spectrophotometer and zeta potentiometer. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42072.     

Synthesis and solution properties of single‐chain microgels from poly(N‐isopropylacrylamide) copolymer

“Single‐chain” microgels were synthesized successfully from the cross‐linkable poly(N‐isopropylacrylamide) (PNIPAM) copolymer. This type of microgel has the exact chemical structure, molecular weight and molecular weight distribution of its precursor. It provides a direct way to compare the properties of linear polymers with those of their networks. The viscosity properties show that the microgels have lower critical solution temperatures (LCST) that are even higher than those of the corresponding linear copolymers. This can be attributed to the crosslinking points, which retard the change of the conformation of the network chains. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2179–2183, 2003     

Thermoresponsive sodium alginate‐g‐poly(N‐isopropylacrylamide) copolymers III. Solution properties

Stimuli‐responsive biocompatible and biodegradable materials can be obtained by combining polysaccharides with polymers exhibiting lower critical solution temperature (LCST) phase behavior, such as poly(N‐isopropylacrylamide) (PNIPAAm). The behavior of aqueous solutions of sodium alginate (NaAl) grafted with PNIPAAm (NaAl‐g‐PNIPAAm) copolymers as a function of composition and temperature is presented. The products obtained exhibit a remarkable thermothickening behavior in aqueous solutions if the degree of grafting, the concentration, and the temperature are higher than some critical values. The sol–gel‐phase transition temperatures have been determined. It was found that at temperatures below LCST the systems behave like a solution, whereas at temperatures above LCST, the solutions behave like a stiff gel, because of PNIPAAm segregation. This behavior is reversible and could find applications in tissue engineering and drug delivery systems. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Concentration effect on aggregation and dissolution behavior of poly(N‐isopropylacrylamide) in water

The concentration effect on aggregation and dissolution behavior of poly(N‐isopropylacrylamide) (PNIPAM) in water was studied. Three concentration regimes with different phase behavior were identified by differential scanning calorimetry (DSC). Further optical, light‐scattering, and rheological studies indicated that the appearance of different regimes arose from their corresponding solution structures below lower critical solution temperature (LCST): free chains and small clusters in regime I, large clusters in regime II, and a gel‐like network in regime III. Different solution structures below LCST led to different phase‐separated patterns formed above LCST: colloidal particles in regime I, large precipitate in regime II, and the sponge‐like solid in regime III, which was well understood based on the overlapping parameter P. Different phase‐separated patterns therefore resulted in different remixing behavior as observed by DSC. This work suggests that the swelling and collapse behavior of PNIPAM based hydrogels was controlled through the design of their phase‐separated patterns, and therefore provided a way to develop high performance thermo‐sensitive materials. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41669.     

Water‐solution properties of a hydrophobically modified poly(N‐isopropylacrylamide)

To study the water‐solution properties of a hydrophobically modified poly(N‐isopropylacrylamide) (PNIPAM) which is temperature‐sensitive, the copolymer of N‐isopropylacrylamide (NIPAM) and octadecyl acrylate (ODA) was synthesized. The aggregation behavior of the copolymer was studied by surface tension and fluorescence probe methods. Simultaneously, the phenomenon of the lower critical solution temperature (LCST) of the copolymer in an aqueous solution with increase of the temperature was also studied using the fluorescence probe method. The results showed that phase separation occurred in an aqueous solution of the copolymer when the temperature was increased to its LCST. The π‐A isotherms for the copolymer molecules, as an insoluble monolayer on the water–air interface, was determined by the Langmuir–Blodgett (L–B) method. The abnormal phenomenon, by which the monolayer of the copolymer molecules became more and more condensed with increase of the temperature, was observed. It further indicated that phase separation of the copolymer occurred by another method. In addition, to prove the thermosensitive effect of the copolymer on the release behavior of liposomes, small unilamellar vesicles entrapped with 5(6)‐carboxyfluorescein [5(6)‐CF] were coated with the copolymer. We found that the coating of the copolymer resulted in the reduction of the release below 30°C and enhancement of the release above 30°C, indicating that there are obvious interactions between the copolymer and the liposomes. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 247–255, 2000     

Poly(N‐isopropylacrylamide‐co‐hydroxyethyl methacrylate) graft copolymers and their application as carriers for drug delivery system

Poly(N‐isopropylacrylamide‐co‐hydroxyethyl methacrylate) [P(NIPAM‐co‐HEMA)] copolymer was synthesized by controlled radical polymerization from respective N‐isopropylacrylamide (NIPAM) and hydroxyethyl methacrylate (HEMA) monomers with a predetermined ratio. To prepare the thermosensitive and biodegradable nanoparticles, new thermosensitive graft copolymer, poly(L ‐lactide)‐graft‐poly(N‐isoporylacrylamide‐co‐hydroxyethyl methacrylate) [PLLA‐g‐P(NIPAM‐co‐HEMA)], with the lower critical solution temperature (LCST) near the normal body temperature, was synthesized by ring opening polymerization of L ‐lactide in the presence of P(NIPAM‐co‐HEMA). The amphiphilic property of the graft copolymers was formed by the grafting of the PLLA hydrophobic chains onto the PNIPAM based hydrophilic backbone. Therefore, the graft copolymers can self‐assemble into uniformly spherical micelles ò about 150–240 nm in diameter as observed by the field emission scanning electron microscope and dynamic light scattering. Dexamethasone can be loaded into these nanostructures during dialysis with a relative high loading capacity and its in vitro release depends on temperature. Above the LCST, most of the drugs were released from the drug‐loaded micelles, whereas a large amount of drugs still remains in the micelles after 48 h below the LCST. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of four‐arm star‐shaped polymers and copolymers

Four‐arm star‐shaped polymers and copolymers were obtained by transition metal‐catalyzed atom‐transfer radical polymerization (ATRP). The polymers were characterized by FTIR and ¹H‐NMR spectroscopy. Gel permeation chromatography results indicated the formation of polystyrene and polystyrene‐block‐poly(methyl methacrylate) (PS‐b‐PMMA) arms with controlled molecular weights. In dilute solution, the linear polymers had higher inherent viscosities than star‐shaped ones. Thermogravimetric analysis showed a similar degradation mechanism for linear and star‐shaped polymers. Differential scanning calorimetry indicated the successful formation of diblock star‐shaped copolymers. Copyright © 2006 Society of Chemical Industry     

Synthesis and characterization of temperature‐sensitive block copolymers from poly(N‐isopropylacrylamide) and 4‐methyl‐ε‐caprolactone or 4‐phenyl‐ε‐caprolactone

This study synthesizes thermally sensitive block copolymers poly(N‐isopropylacrylamide)‐b‐poly(4‐methyl‐ε‐caprolactone) (PNIPA‐b‐PMCL) and poly(N‐isopropylacrylamide)‐b‐poly(4‐phenyl‐ε‐caprolactone) (PNIPA‐b‐PBCL) by ring‐opening polymerization of 4‐methyl‐ε‐caprolactone (MCL) or 4‐phenyl‐ε‐caprolactone (BCL) initiated from hydroxy‐terminated poly(N‐isopropylacrylamide) (PNIPA) as the macroinitiator in the presence of SnOct₂ as the catalyst. This research prepares a PNIPA bearing a single terminal hydroxyl group by telomerization using 2‐hydroxyethanethiol (ME) as a chain‐transfer agent. These copolymers are characterized by differential scanning calorimetry (DSC), ¹H‐NMR, FTIR, and gel permeation chromatography (GPC). The thermal properties (T_g) of diblock copolymers depend on polymer compositions. Incorporating larger amount of MCL or BCL into the macromolecular backbone decreases T_g. Their solutions show transparent below a lower critical solution temperature (LCST) and opaque above the LCST. LCST values for the PNIPA‐b‐PMCL aqueous solution were observed to shift to lower temperature than that for PNIPA homopolymers. This work investigates their micellar characteristics in the aqueous phase by fluorescence spectroscopy, transmission electron microscopy (TEM), and dynamic light scattering (DLS). The block copolymers formed micelles in the aqueous phase with critical micelle concentrations (CMCs) in the range of 0.29–2.74 mg L^?1, depending on polymer compositions, which dramatically affect micelle shape. Drug entrapment efficiency and drug loading content of micelles depend on block polymer compositions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of a novel liquid crystalline star‐shaped polymer based on α‐CD core via ATRP

Well‐defined side‐chain liquid crystalline star‐shaped polymers were synthesized with a combination of the “core‐first” method and atom transfer radical polymerization (ATRP). Firstly, the functionalized macroinitiator based on the α‐Cyclodextrins (α‐CD) bearing functional bromide groups was synthesized, confirmed by ¹H‐NMR, MALDI‐TOF, and FTIR analysis. Secondly, the side‐chain liquid crystalline arms poly[6‐(4‐methoxy‐4‐oxy‐azobenzene) hexyl methacrylate] (PMMAzo) were prepared by ATRP. The characterization of the star polymers were performed with ¹H‐NMR, gel permeation chromatography (GPC), differential scanning calorimetry (DSC) and thermal polarized optical microscopy (POM). It was found that the liquid crystalline behavior of the star polymer α‐CD‐PMMAzo_n was similar to that of the linear homopolymer. The phase‐transition temperatures from the smectic to nematic phase and from the nematic to isotropic phase increased as the molecular weight increased for most of these samples. All star‐shaped polymers show photoresponsive isomerization under the irradiation with Ultraviolet light. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Simultaneous lower and upper critical solution temperature‐type co‐nonsolvency behaviour exhibited in water–dioxane mixtures by linear copolymers and hydrogels containing N‐isopropylacrylamide and N,N‐dimethylacrylamide

The co‐nonsolvency behaviour in water–dioxane mixtures of linear copolymers and hydrogels consisting of N‐isopropylacrylamide (NIPAM) and N,N‐dimethylacrylamide (DMAM) was studied as a function of solvent composition and temperature. The composition of the copolymers, P(NIPAM‐co‐DMAMx), in DMAM units, x, varies from x = 0 up to x = 100%. It is shown that the copolymers combine the lower critical solution temperature (LCST)‐type co‐nonsolvency behaviour of poly‐NIPAM with the upper critical solution temperature (UCST)‐type co‐nonsolvency behaviour of poly‐DMAM. Depending on x, both the LCST‐ and UCST‐type co‐nonsolvency behaviour may be simultaneously observed in water‐rich and dioxane‐rich solvent mixtures, respectively. Due to this complex phase separation behaviour, the variation of the reduced viscosity of the linear copolymers, as well as the swelling–deswelling behaviour of the respective hydrogels, are shown to be temperature‐ and solvent‐sensitive. Copyright © 2006 Society of Chemical Industry     

Incorporation of azobenzene chromophore into poly(amide‐imide)

Poly(amide‐imide)s (PAI) bearing azobenzene chromophore groups were prepared by allowing a hydroxyl‐containing azobenzene dye (Disperse Red 1) to react with and reactive‐terminated PAI with weight–average molecular weights ranging from ～ 1.2 to 2.0 × 10⁴ g/mol. Such PAI were prepared by the condensation of trimellitic anhydride (TMA) and 4,4′‐methylene diphenyl diisocyanate (MDI). The final polymers presented a deep red color, with an absorption maxima in N,N‐dimethylformamide (DMF) solution at 490 nm, close to the azobenzene reactant used (Disperse Red 1) and molecular weights slightly higher than the pristine polymer, showing that the azo chromophore incorporation reaction does not lead to side reactions. The azofunctionalized polymer presented a high T_g value (170°C) that could be increased by a thermal curing process to 240°C. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 841–847, 2007