The effect of epoxidized natural rubber on mechanical properties of siliceous earth/natural rubber composites

Siliceous earth (SE) is a kind of mineral consisting of lamellar kaolinite, muscovite (aluminum silicate) and corpuscular silica. Natural rubber (NR) composites containing NR as matrix, epoxidized natural rubber (ENR) as compatibilizer and SE as filler were produced by latex coagulating process and cured using a conventional sulfuric system. Monsanto measurements have shown that the ENR accelerates the vulcanization reaction and gives rise to a marked increase of the torque. The results of physico-mechanical properties of NR vulcanizates show that, when SE modified by silane coupling agent and in the meanwhile adding 4 phr of ENR as compatibilizer, maximum tensile strength, elongation at break, reinforcing index (M300/100) of NR/SE vulcanizates were obtained. The dynamic-mechanical properties exhibit the addition of ENR can enhance wet grip characteristics and reduce rolling resistance by lowering tan δ values at 60 °C and increasing tan δ values at 0 °C of NR compounds. The overall results show that properties of SE-reinforced NR substantially improved by adding ENR as compatibilizer. The addition of silane coupling agent and combining an appropriate amount of ENR would be better choice to improve the properties of NR/SE compounds.     

Physical properties of natural rubber/organoclay nanocomposites compatibilized with epoxidized natural rubber

Onium ion‐modified montmorillonite (organoclay) was melt compounded with natural rubber (NR) in an internal mixer and cured by using a conventional sulfuric system. Epoxidized natural rubber with 50 mol % epoxidation (ENR 50) was used in 10 parts per hundred rubber (phr) as a compatibilizer. The effect of organoclay with different filler loading up to 10 phr was studied. Cure characteristics were determined by a Monsanto MDR2000 rheometer, whereas the tensile, compression, and tear properties of the nanocomposites were measured according to the related ASTM standards. While the torque maximum and torque minimum increased slightly, both scorch time and cure time reduced with the incorporation of organoclay. The tensile strength, elongation at break, and tear properties went through a maximum (at about 2 phr) as a function of the organoclay content. As expected, the hardness, moduli at 100% (M100) and 300% elongations (M300) increased continuously with increasing organoclay loading. The compression set decreased with incorporation of organoclay. The dispersion of the organoclay in the NR stocks was investigated by X‐ray diffraction and transmission electron microscopy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1083–1092, 2006     

Self‐crosslinkable lignin/epoxidized natural rubber composites

Self‐crosslinkable lignin/epoxidized natural rubber composites (SLEs) were prepared through a high‐temperature dynamic heat treatment procedure followed by a postcuring process. Because of the ring‐opening reaction between lignin and epoxidized natural rubber (ENR), lignin as a crosslinker and reinforcing filler was uniformly dispersed into the ENR matrix and was highly compatible with the polymer matrix; this was confirmed by scanning electron microscopy. The curing behavior, mechanical properties, and dynamic mechanical properties of the SLEs were studied. The results show that the crosslinking degree, glass‐transition temperature, modulus, and tensile properties of the SLEs substantially increased with the addition of lignin. A physical model was used to verify the strong interactions between lignin and ENR. Stress–strain curves and X‐ray diffraction suggested that the reinforcement effect on the SLEs mainly originated from lignin itself rather than from strain‐induced crystallization. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41166.     

Mechanical properties and blend compatibility of natural rubber –chlorosulfonated polyethylene blends

Natural rubber (NR) was blended with chlorosulfonated polyethylene (CSM) with various formulation and blend ratios (NR/CSM: 80/20 –20/80, wt/wt). Rubber blends were prepared by using a two‐roll mill and vulcanized in a compression mold to obtain the 2 mm‐thick sheets. Tensile properties, tear resistance, thermal aging resistance, ozone resistance, and oil resistance were determined according to ASTM. Compatible NR/CSM blends are derived from certain blends containing 20–30% CSM without adding any compatibilizing agent. Tensile and tear strength of NR‐rich blends for certain formulations show positive deviation from the rule of mixture. Thermal aging resistance depends on formulation and blend ratio, while ozone and oil resistance of the blends increase with CSM content. Homogenizing agents used were Stuktol®60NS and Epoxyprene®25. Stuktol®60NS tends to decrease the mechanical properties of the blends and shows no significant effect on blend morphology. Addition of 5–10 phr of epoxidized natural rubber (ENR, Epoxyprene® 25) increases tensile strength, thermal aging resistance, and ozone resistance of the blends. It is found that ENR acts as a compatibilizer of the NR/CSM blends by decreasing both CSM particle size diameter and α transition temperature of CSM. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 127–140, 2006     

Phenolic resin‐crosslinked natural rubber/clay nanocomposites: Influence of clay loading and interfacial adhesion on strain‐induced crystallization behavior

Nanocomposites of natural rubber (NR) and pristine clay (clay) were prepared by latex mixing, then crosslinked with phenolic resin (PhOH). For comparative study, the PhOH‐crosslinked neat NR was also prepared. Influence of clay loading (i.e., 1, 3, 5, and 10 phr) on mechanical properties and structural change of PhOH‐crosslinked NR/clay nanocomposites was studied through X‐ray diffraction (XRD), transmission electron microscopic (TEM), wide‐angle X‐ray diffraction (WAXD), tensile property measurement, and Fourier transform infrared spectroscopy (FTIR). XRD and TEM showed that the clay was partly intercalated and aggregated, and that the dispersion state of clay was non‐uniform at higher clay loading (>5 phr). From tensile test measurement, it was found that the pronounced upturn of tensile stress was observed when the clay loading was increased and a maximum tensile strength of the PhOH‐crosslinked NR/clay nanocomposites was obtained at 5 phr clay. WAXD observations showed that an increased addition of clay induced more orientation and alignment of NR chains, thereby lowering onset strain of strain‐induced crystallization and promoting crystallinity of the NR matrix during tensile deformation. FTIR investigation indicated a strong interfacial adhesion between NR matrix and clay filler through a phenolic resin bridge. This suggested that the PhOH did not only act as curative agent for crosslinking of NR, but it also worked as coupling agent for promoting interfacial reaction between NR and clay. The presence of strong interfacial adhesion was found to play an important role in the crystallization process, leading to promotion of mechanical properties of the PhOH‐crosslinked NR/clay nanocomposites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43214.     

High‐performance bio‐based poly(lactic acid)/natural rubber/epoxidized natural rubber blends: effect of epoxidized natural rubber on microstructure,toughness and static and dynamic mechanical properties

Attempts have been made to prepare high‐performance bio‐based blends through blending of poly(lactic acid) (PLA) with natural rubber (NR) in the presence of epoxidized natural rubber (ENR) as a compatibilizer. The prepared samples were characterized using differential scanning calorimetry, measuring the tensile properties and impact resistance, scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy and dynamic mechanical analysis (DMTA). Morphological studies revealed a matrix‐dispersed morphology for all blends, in which the average droplet size significantly decreased with the use of ENR. The elongation at break and impact strength of the blend containing 3 wt% ENR were 45 and 16 times those of neat PLA, respectively. These values are significantly higher than those previously reported for various simple and dynamically vulcanized rubber‐toughened PLAs. The influence of ENR on compatibility was confirmed by rheological tests, FTIR spectra and DMTA. DMTA also showed a marked increase in elastic modulus for the blend in the presence of 3 wt% ENR. The tensile properties and impact resistance were directly dependent on the ENR content and rubber droplet size. © 2018 Society of Chemical Industry     

Preparation and characterization of organoclay‐rubber nanocomposites via a new route with skim natural rubber latex

Skim natural rubber latex (SNRL) is a protein rich by‐product obtained during the centrifugal concentration of natural rubber (NR) latex. A new method to recover rubber hydrocarbon and to obtain nanocomposites with organoclay (OC) was investigated. The approach involved treatment of SNRL with alkali and surfactant, leading to creaming of skim latex and removal of clear aqueous phase before addition of OC dispersion. Clay mixed latex was then coagulated to a consolidated mass by formic acid, followed by drying and vulcanization like a conventional rubber vulcanizate. X‐ray diffraction (XRD) studies revealed that NR nanocomposites exhibited a highly intercalated structure up to a loading of 15 phr (parts per hundred rubber) of OC. Transmission electron microscopy studies showed a highly exfoliated and intercalated structure for the NR nanocomposites at loadings of 3–5 phr organically modified montmorillonite (OMMT). The presence of clay resulted in a faster onset of cure and higher rheometric torque. The rubber recovered from skim latex had a high gum strength, and a low amount of OC (5 phr) improved the modulus and tensile strength of NR. The high tensile strength was supported by the tensile fractography from scanning electron microscopy. Thermal ageing at 70°C for 6 days resulted in an improvement in the modulus of the samples; the effect was greater for unfilled NR vulcanizate. The maximum degradation temperature was found to be independent of the presence and concentration of OC. The increased restriction to swelling with the loading of OC suggested a higher level of crosslinking and reinforcement in its presence. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3277–3285, 2006     

Physical properties and cure characteristics of natural rubber/nanoclay composites with two different compatibilizers

The effects of epoxidized natural rubber (ENR) and maleic anhydride‐grafted polybutadiene (PB‐g‐MA) as compatibilizers to rubber formulations with and without organo‐modified layered silicates are investigated. The physical properties and curing characteristics of composites are studied by moving die rheometer, rubber process analyzer, tensile, tear, and hardness testing. The state of organoclay intercalation was determined by X‐ray diffraction method. The addition of compatibilizers, especially ENR 50, results in further intercalation or exfoliation of the organoclay that increased the clay dispersion in the rubber matrix. ENR 50 with organo‐modified clay improves the physical properties and changes the curing profile. The addition of PB‐g‐MA without organoclay increases the tensile strength (σ_max) by increasing the stock viscosity of the rubber compound. Interestingly, simultaneous increase in hardness and σ_max is achieved in the presence of both compatibilizers, a characteristic that is difficult to achieve and sometimes required in rubber processing. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

In situ dispersion and compatibilization of lignin/epoxidized natural rubber composites: reactivity,morphology and property

Lignin, a naturally occurring polymer, was viewed as a potential substitute of carbon black for reinforcing rubber materials. However, it shows no reinforcing effect if directly mixed with rubber. In this study, lignin was in situ dispersed at submicrometer size and highly compatible with epoxidized natural rubber (ENR) by using a high‐temperature dynamic heat treatment (HTDHT). Rheology analysis indicated that the ring opening reaction between lignin and ENR occurred at 160°C or above, which was further confirmed by infrared spectroscopy. Due to the consumption of acidic groups of lignin by ENR, the retardant vulcanization effect of lignin was weakened. Morphology observation and dynamic mechanical analysis demonstrated the perfect lignin dispersion and the strong interactions between lignin and ENR. The mechanical properties of the lignin/ENR composites were significantly improved by using HTDHT. Compared to the directly mixed rubber composites, the tensile strength and tear strength of the heat treated rubber composites filled with 40 phr lignin were increased by 114% and 23%, respectively. Especially, the 300% modulus of the heat treated rubber composite was increased by ca. 400%. X‐ray diffraction results indicated that the reinforcement of the composites originated from the presence of lignin rather than the strain‐induced crystallization of ENR. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42044.     

反式聚辛烯橡胶改性天然橡胶/顺丁橡胶共混胶的性能

研究了反式聚辛烯橡胶(TOR)改性天然橡胶(NR)/顺丁橡胶(BR)(二者质量比80/20)共混胶的性能.结果表明,采用5～15份(质量,下同)TOR改性NR/BR混炼胶的门尼黏度逐渐降低、Payne效应基本不变,共混胶的焦烧时间和工艺正硫化时间延长、硫化速率减慢.相比NR/BR硫化胶,NR/BR/TOR硫化胶的拉伸强...     

Effects of epoxidized natural rubber (ENR‐50) and processing parameters on the properties of NR/EPDM blends using response surface methodology

The effects of epoxidized natural rubber (ENR‐50) and processing parameters on the properties of natural rubber/ethylene–propylene–diene rubber (NR/EPDM; 70 : 30 phr) blends were studied. The compounds were prepared by melt compounding method. Using response surface methodology of two‐level full factorial, the effects of ENR‐50 contents (?1 : 5 phr; +1 : 10 phr), mixing temperature (?1 : 50°C; +1 : 110°C), rotor speed (?1 : 40 rpm; +1 : 80 rpm), and mixing time (?1 : 5 min; +1 : 9 min) in NR/EPDM blends were evaluated. Cure characteristics and tensile properties were selected as the responses. The significance of factors and its interaction was analyzed using ANOVA and the model's ability to represent the system was confirmed using the constant of determination, R² with values above 0.90. It was found that the presence of ENR‐50 has the predominant role on the properties of NR/EPDM blends. The addition of ENR‐50 significantly improved cure characteristics and tensile strength up to 5.12% and 6.48% compared to neat NR/EPDM blends, respectively. These findings were further supported by swell measurement, differential scanning calorimetry, and scanning electron microscopy. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40713.     

Understanding the reinforcing efficiency of waste eggshell‐derived nano calcium carbonate in natural rubber composites with maleated natural rubber as compatibilizer

Calcium carbonate nanoparticles were synthesized from eggshell waste using ball mill treatment and characterized by Fourier transform infrared (FTIR), X‐ray diffraction (XRD), and field‐emission scanning electron microscopy (FESEM) analysis. Then, waste eggshell‐derived nano calcium carbonate (WESNCC) was used as filler to reinforce natural rubber (NR) composites with and without the presence of maleated natural rubber (MNR) as compatibilizer. MNR‐compatibilized NR/WESNCC composites showed remarkable enhancement in the torque difference, tensile, and thermal properties as compared to either uncompatibilized NR/WESNCC composites or unfilled NR system. Crosslinking degree measurements indicated excellent interfacial interaction between NR matrix and WESNCC in presence of MNR as compatibilizer. A probable mechanism is suggested to explain the interaction between NR matrix and WESNCC in the presence of MNR. This study provides unique way to develop WESNCC‐based rubber composites for future industrial and engineering application. POLYM. ENG. SCI., 59:1428–1436 2019. © 2019 Society of Plastics Engineers     

Surface modification of nanocrystalline cellulose and its application in natural rubber composites

As a biopolymer with high mechanical strength, nanocellulose was generally considered as a green filler for reinforcing polymer. In this study, nanocrystalline cellulose (NCC) isolated from softwood pulp was successfully modified by cetyltrimethyl ammonium bromide (CTMAB), a cationic surfactant, and the modified nanocrystalline cellulose (m-NCC) was used to reinforce natural rubber (NR). In this composite architecture, it was found that when the filler content was 5 or 10 phr, the surface modification of NCC improved the dispersion state of NCC in NR matrix and the interfacial interaction between NR and NCC. Therefore, the NR/m-NCC composites exhibited outstanding mechanical properties, and its tensile strength, elongation at break and tear strength was increased by 132.8, 20, and 66.1%, respectively, compared to pristine NR composites. Besides, the modified NCC could accelerate the vulcanization and improve wet-skid resistance and aging resistance of NR composites. It is envisioned that the modified NCC has the potential to be generalized to manufacturing other polymer matrix composites strengthened with nanocellulose.     

Organomodified kaolin as a reinforcing filler for natural rubber

China clay (kaolin) has been modified with sodium salt of rubber seed oil (SRSO). SRSO was characterized using X‐ray diffraction (XRD), infrared spectroscopy (FTIR), and differential thermal analysis (DTA). XRD of the unmodified and SRSO‐modified kaolins showed an increase in the d‐(001) spacing of kaolin platelets from 7.15 to 14 Å. FTIR spectroscopy indicated possible grafting of the organic moiety of rubber seed oil (RSO) onto the clay surface. DTA of the SRSO‐modified kaolin indicated that the SRSO is more strongly bound in a constraint environment within the lamellae of kaolin. Natural rubber (NR) mix containing 10 phr of SRSO‐modified kaolin was found to cure faster than that of a similar mix containing unmodified kaolin. NR vulcanizates containing SRSO‐modified kaolin showed considerable increase in tensile modulus, tensile strength, and elongation at break indicating its potential as an organomodified nanofiller. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Chemically modified oil palm ash‐filled natural rubber composites and its properties

Chemically modified Oil Palm Ash (OPA)‐filled natural rubber composites were prepared by modifying the functional group of OPA with cetyltrimethylammonium bromide (CTAB) prior to compounding by using laboratory conventional laboratory‐sized two‐roll mills. The functional groups of CTAB‐modified OPA were analyzed by using Fourier Transform Infrared (FTIR) and compared with those of non‐modified ones. The CTAB‐modified OPA‐filled NR composites showed shorter scorch time and cure time as compared to those of non‐modified OPA, which was attributed to the new functional groups occurred. The tensile test results showed that the OPA‐filled NR composites with CTAB modification exhibit improvement in tensile strength, tensile modulus, and hardness but lower elongation at break as compared to nonmodified ones. The tensile fractured surface of modified OPA filled NR composites revealed the well embedded and better distribution of CTAB‐modified OPA in NR matrix. The toluene uptake was also found to be lower for the modified OPA‐filled NR composites and showed better rubber–filler interaction; it further showed that surface modification with CTAB could compatibilize the OPA particles and NR matrix. POLYM. COMPOS., 35:691–697, 2014. © 2013 Society of Plastics Engineers     

Kaolin modified with sodium salt of rubber seed oil as a reinforcing filler for blends of natural rubber,polybutadiene rubber and acrylonitrile–butadiene rubber

Blends of natural rubber (NR) and synthetic rubbers are widely used in the rubber industry to meet specific performance requirements. Further, the emerging field of organomodified clay/rubber nanocomposites could provide a host of novel materials having a unique combination of properties to meet various stringent service conditions. Previous studies have shown that at very low dosages, china clay (kaolin) modified with sodium salt of rubber seed oil (SRSO) improved the cure characteristics and physico‐mechanical properties of NR. Results of the present study show improved cure characteristics and physico‐mechanical properties for blends of NR with butadiene rubber and nitrile rubber containing 4 phr of SRSO‐modified kaolin as indicated by reduction in optimum cure time along with higher tensile strength, tensile modulus and elongation at break for their vulcanizates as compared to those containing unmodified kaolin. The SRSO‐modified kaolin/rubber nanocomposites showed improved flex resistance, reduced heat build‐up, tan delta and loss modulus and higher chemical crosslink density index, indicating a reinforcing effect of the SRSO‐modified kaolin, enabling the nanocomposites to have potential industrial applications. © 2015 Society of Chemical Industry     

Effect of organoclay loading level on mechanical properties,thermomechanical behavior,and heat build‐up of natural rubber/organoclay nanocomposites

Sodium‐montmorillonite nanoclay was modified with octadecylamine and compounded with natural rubber (NR) by dry mixing method. The effects of organoclay loading level on mechanical properties, thermal–mechanical behavior, and heat build‐up of NR/organoclay nanocomposites were investigated. Temperature scanning stress relaxation technique was used to characterize the thermal–mechanical behavior of the composites. The morphological properties were assessed by X‐ray diffraction and transmission electron microscopy. Loading levels of organoclay below 5 phr gave improved mechanical properties and heat build‐up, along with exfoliated clay structure in the nanocomposites. On the other hand, with loading levels above 7 phr the organoclay tended to agglomerate, and X‐ray diffraction revealed an intercalated structure. In these cases, the excess residual organoclay caused significantly increased stress relaxation and heat build‐up. Unmodified sodium‐montmorillonite as filler did not significantly affect the mechanical and heat build‐up properties of NR vulcanizates. POLYM. COMPOS., 37:1735–1743, 2016. © 2014 Society of Plastics Engineers     

天然橡胶增韧聚氯乙烯的研究

采用未改性的标准天然橡胶(NR)作增韧剂,通过机械共混法制备增韧聚氯乙烯(PVC)复合材料,考察了NR和增容剂用量对PVC增韧效果以及力学性能的影响.结果表明:当NR用量为10份时,材料的冲击强度最高为24.87 kJ/m2;加入增容剂环氧化天然橡胶(ENR)后,材料的冲击强度随其用量的增加而增大,在ENR为5份时其冲击强度为69.86 kJ/m2;氯化聚乙烯(CPE)作增容剂时,其冲击强度先升后降,在4份时达到峰值103.93 kJ/m2;氯化橡胶(CNR)作增容剂在3份时,其冲击强度达到最佳值35.37 kJ/m2;增容增韧后共混物的拉伸强度普遍降低.     

New approach for preparation of dry natural rubber nanocomposites through acid‐free co‐coagulation: Effect of organoclay content

Natural rubber (NR) vulcanizates exhibit good mechanical properties compared to vulcanizates of synthetic rubbers. Incorporation of a conventional filler at higher loadings to NR enhances its modulus, while reduction in tensile strength and elongation. This paper presents a new strategy for development of a NR‐clay nanocomposite with enhanced mechanical properties by incorporation of lower loadings (2–8 phr) of cetyl trimethyl ammonium bromide modified montmorillonite clay (OMMT‐C) under acid‐free environment. The effect of OMMT‐C loading on cure characteristics, rubber‐filler interactions, crosslink density, dynamic mechanical thermal properties, and mechanical properties were evaluated. Incorporation of OMMT‐C accelerated the vulcanization process and enhanced mechanical properties. X‐ray diffraction analysis and scanning electron microscopy images revealed that the formation of intercalated clay structures at lower OMMT‐C loadings, and clay aggregates at higher loadings. A nanocomposite at OMMT‐C loading of 2 phr exhibited the best balanced mechanical properties, and was associated with highest crosslink density and rubber–filler interactions. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46502.     

Curing characteristics and mechanical properties of rattan‐powder‐filled natural rubber composites as a function of filler loading and silane coupling agent

Curing characteristics, tensile properties, morphological studies of tensile fractured surfaces using scanning electron microscopy (SEM), and the extent of rubber filler interactions of rattan‐powder‐filled natural rubber (NR) composites were investigated as a function of filler loading and silane coupling agent (CA). NR composites were prepared by the incorporation of rattan powder at filler loading range of 0–30 phr into a NR matrix with a laboratory size two roll mill. The results indicate that in the presence of silane CA, scorch time (t_s2), and cure time (t₉₀) of rattan‐powder‐filled NR composites were shorten, while, maximum torque (M_H) increased compared with NR composites without silane CA. Tensile strength and tensile modulus of composites were enhanced whereas elongation at break reduced in the presence of silane CA mainly due to increase in rubber‐filler interaction. It is proven by SEM studies that the bonding between the filler and rubber matrix has improved. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012