Solution‐Processed Bulk‐Heterojunction Solar Cells Based on Monodisperse Dendritic Oligothiophenes

A novel family of soluble conjugated dendritic oligothiophenes (DOTs) as monodisperse 3D macromolecular architectures was characterized with respect to optical and redox properties in solution and in solid films. Band gaps of 2.5–2.2 eV, typical for organic semiconductors, were determined as well as HOMO/LUMO energy levels ideal for efficient electron transfer to acceptors such as [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) identifying them as suitable materials for solar cell applications. Solution‐processed bulk‐heterojunction solar cells using DOTs as electron donor and PCBM as acceptor were prepared and investigated. High open‐circuit voltages V_OC of 1.0 V and power‐conversion efficiencies up to 1.72% were obtained for the DOT‐based devices. The higher generations DOTs provide the highest efficiencies. Based on the monodispersity of the DOTs, an analysis of the molar ratio between donor and acceptor in the blended film was possible leading to an optimal value of five to six thiophene units per PCBM.     

Diphenylmethanofullerenes: New and Efficient Acceptors in Bulk‐Heterojunction Solar Cells

A novel fullerene derivative, 1,1‐bis(4,4′‐dodecyloxyphenyl)‐(5,6) C₆₁, diphenylmethanofullerene (DPM‐12), has been investigated as a possible electron acceptor in photovoltaic devices, in combination with two different conjugated polymers poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐para‐phenylene vinylene] (OC₁C₁₀‐PPV) and poly[3‐hexyl thiophene‐2,5‐diyl] (P3HT). High open‐circuit voltages, V_OC = 0.92 and 0.65 V, have been measured for OC₁C₁₀‐PPV:DPM‐12‐ and P3HT:DPM‐12‐based devices, respectively. In both cases, V_OC is 100 mV above the values measured on devices using another routinely used fullerene acceptor, [6,6]‐phenyl‐C₆₁ butyric acid methyl ester (PCBM). This is somewhat unexpected when taking into account the identical redox potentials of both acceptor materials at room temperature. The temperature‐dependent V_OC reveals, however, the same effective bandgap (HOMO_Polymer–LUMO_Fullerene; HOMO = highest occupied molecular orbital, LUMO = lowest unoccupied molecular orbital) of 1.15 and 0.9 eV for OC₁C₁₀‐PPV and P3HT, respectively, independent of the acceptor used. The higher V_OC at room temperature is explained by different ideality factors in the dark‐diode characteristics. Under white‐light illumination (80 mW cm^–2), photocurrent densities of 1.3 and 4.7 mA cm^–2 have been obtained in the OC₁C₁₀‐PPV:DPM‐12‐ and P3HT:DPM‐12‐based devices, respectively. Temperature‐dependent current density versus voltage characteristics reveal a thermally activated (shallow trap recombination limited) photocurrent in the case of OC₁C₁₀‐PPV:DPM‐12, and a nearly temperature‐independent current density in P3HT:DPM‐12. The latter clearly indicates that charge carriers traverse the active layer without significant recombination, which is due to the higher hole‐mobility–lifetime product in P3HT. At the same time, the field‐effect electron mobility in pure DPM‐12 has been found to be μ_e = 2 × 10^–4 cm² V^–1 s^–1, that is, forty‐times lower than the one measured in PCBM (μ_e = 8 × 10^–3 cm² V^–1 s^–1).     

Improved Performance of Molecular Bulk‐Heterojunction Photovoltaic Cells through Predictable Selection of Solvent Additives

Solvent additives provide an effective means to alter the morphology and thereby improve the performance of organic bulk‐heterojunction photovoltaics, although guidelines for selecting an appropriate solvent additive remain relatively unclear. Here, a family of solvent additives spanning a wide range of Hansen solubility parameters is applied to a molecular bulk‐heterojunction system consisting of an isoindigo and thiophene containing oligomer as the electron donor and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) as the electron acceptor. Hansen solubility parameters are calculated using the group contribution method and compared with the measured solubilities for use as a screening method in solvent additive selection. The additives are shown to alter the morphologies in a semipredictable manner, with the poorer solvents generally resulting in decreased domain sizes, increased hole mobilities, and improved photovoltaic performance. The additives with larger hydrogen bonding parameters, namely triethylene glycol (TEG) and N‐methyl‐2‐pyrrolidone (NMP), are demonstrated to increase the open circuit voltage by ~0.2 V. Combining a solvent additive observed to increase short circuit current, poly(dimethylsiloxane), with TEG results in an increase in power conversion efficiency from 1.4 to 3.3%.     

Charge Transport and Photocurrent Generation in Poly(3‐hexylthiophene): Methanofullerene Bulk‐Heterojunction Solar Cells

The effect of controlled thermal annealing on charge transport and photogeneration in bulk‐heterojunction solar cells made from blend films of regioregular poly(3‐hexylthiophene) (P3HT) and methanofullerene (PCBM) has been studied. With respect to the charge transport, it is demonstrated that the electron mobility dominates the transport of the cell, varying from 10^–8 m² V^–1 s^–1 in as‐cast devices to ≈3 × 10^–7 m² V^–1 s^–1 after thermal annealing. The hole mobility in the P3HT phase of the blend is dramatically affected by thermal annealing. It increases by more than three orders of magnitude, to reach a value of up to ≈ 2 × 10^–8 m² V^–1 s^–1 after the annealing process, as a result of an improved crystallinity of the film. Moreover, upon annealing the absorption spectrum of P3HT:PCBM blends undergo a strong red‐shift, improving the spectral overlap with solar emission, which results in an increase of more than 60 % in the rate of charge‐carrier generation. Subsequently, the experimental electron and hole mobilities are used to study the photocurrent generation in P3HT:PCBM devices as a function of annealing temperature. The results indicate that the most important factor leading to a strong enhancement of the efficiency, compared with non‐annealed devices, is the increase of the hole mobility in the P3HT phase of the blend. Furthermore, numerical simulations indicate that under short‐circuit conditions the dissociation efficiency of bound electron–hole pairs at the donor/acceptor interface is close to 90 %, which explains the large quantum efficiencies measured in P3HT:PCBM blends.     

Additive‐Free Bulk‐Heterojuction Solar Cells with Enhanced Power Conversion Efficiency,Comprising a Newly Designed Selenophene‐Thienopyrrolodione Copolymer

Bulk‐heterojunction solar cells are reported with an enhanced power conversion efficiency (PCE) based on a newly designed semiconducting selenophene‐thienopyrrolodione (TPD) copolymer blended with [6,6]‐phenyl C₇₁ butyric acid methyl‐ester. The solar cells are fabricated using simple solution processing (implying low‐cost fabrication). The relatively deep highest occupied molecular orbital (HOMO) level leads to a correspondingly high open‐circuit voltage of 0.88 V. The PCE approaches 5.8% when Clevious P VP AI4083 is used as the hole‐transport interlayer, with an optimized active layer thickness of approximately 95 nm, and a donor‐acceptor blend ratio of 1:1. A fill factor (FF) of 0.62 is achieved. The use of additives does not seem to be beneficial in this blended system, due to the achievement of proper phase separation in the as‐cast films. Also, the BHJ devices with a 3% ratio of a 1‐chloronaphthalene (CN) additive exhibit much more severe oxidative degradation from the decreased FF with a high series resistance than BHJ devices without additive. The selenophene‐TPD based BHJ solar cell is a promising candidate for high‐performance single cells with a low‐cost additive‐free fabrication and a long‐term stable operation.     

Quinacridone‐Based Electron Transport Layers for Enhanced Performance in Bulk‐Heterojunction Solar Cells

A water/alcohol‐soluble small molecule based on the commercially available pigment quinacridone is employed as an electron transport layer in organic photovoltaics. The quinacridone derivative is utilized in solution‐processed bulk‐heterojunction solar cells to improve primarily the fill factor of the devices, contributing to an upwards of 19% enhancement in the power conversion efficiency relative to the control devices with no electron transport layer. The facile synthesis of the quinacridone derivative coupled with the ease of device fabrication via solution processing provide a simple, yet effective means of improving the performance of existing organic photovoltaic cells.     

Identifying a Threshold Impurity Level for Organic Solar Cells: Enhanced First‐Order Recombination Via Well‐Defined PC84BM Traps in Organic Bulk Heterojunction Solar Cells

Small amounts of impurity, even one part in one thousand, in polymer bulk heterojunction solar cells can alter the electronic properties of the device, including reducing the open circuit voltage, the short circuit current and the fill factor. Steady state studies show a dramatic increase in the trap‐assisted recombination rate when [6,6]‐phenyl C₈₄ butyric acid methyl ester (PC₈₄BM) is introduced as a trap site in polymer bulk heterojunction solar cells made of a blend of the copolymer poly[N‐9″‐hepta‐decanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole) (PCDTBT) and the fullerene derivative [6,6]‐phenyl C₆₁ butyric acid methyl ester (PC₆₀BM). The trap density dependent recombination studied here can be described as a combination of bimolecular and Shockley–Read–Hall recombination; the latter is dramatically enhanced by the addition of the PC₈₄BM traps. This study reveals the importance of impurities in limiting the efficiency of organic solar cell devices and gives insight into the mechanism of the trap‐induced recombination loss.     

Dicyanovinyl–Substituted Oligothiophenes: Structure‐Property Relationships and Application in Vacuum‐Processed Small Molecule Organic Solar Cells

Efficient synthesis of a series of terminally dicyanovinyl (DCV)‐substituted oligothiophenes, DCVnT 1–6, without solubilizing side chains synthesized via a novel convergent approach and their application as electron donors in vacuum‐processed m‐i‐p‐type planar and p‐i‐n‐type bulk heterojunction organic solar cells is described. Purification of the products via gradient sublimation yields thermally highly stable organic semiconducting materials in single crystalline quality which allows for X‐ray structure analysis. Important insights into the packing features and intermolecular interactions of these promising solar cell materials are provided. Optical absorption spectra and electrochemical properties of the oligomers are investigated and valuable structure–property relationships deduced. Photovoltaic devices incorporating DCVnTs 4–6 showed power conversion efficiencies up to 2.8% for planar and 5.2% for bulk heterojunction organic solar cells under full sun illumination (mismatch corrected simulated AM 1.5G sunlight). The 5.2% efficiency shown here represents one of the highest values ever reported for organic vacuum‐deposited single heterojunction solar cells.     

The Effect of H‐ and J‐Aggregation on the Photophysical and Photovoltaic Properties of Small Thiophene–Pyridine–DPP Molecules for Bulk‐Heterojunction Solar Cells

The performance of organic semiconductors in optoelectronic devices depends on the functional properties of the individual molecules and their mutual orientations when they are in the solid state. The effect of H‐ and J‐aggregation on the photophysical properties and photovoltaic behavior of four electronically identical but structurally different thiophene–pyridine–diketopyrrolopyrrole molecules is studied. By introducing and changing the position of two hexyl side chains on the two peripheral thiophene units of these molecules, their aggregation in thin films between H‐type and J‐type is effectively tuned, as evidenced from the characteristics of optical absorption, fluorescence, and excited state lifetime. The two derivatives that assemble into J‐type aggregates exhibit a significantly enhanced photovoltaic performance, up to an order of magnitude, compared to the two molecules that form H‐type aggregates. The reasons for this remarkably different behavior are discussed.     

基于高效体异质结的聚合物太阳电池研究

介绍了体异质结聚合物太阳电池的基本原理,并分析了限制体异质结有机太阳电池转化效率的因素。从提高激子的产生效率及其解离效率、电极对电荷的引出效率、电池的稳定性以及电池的光谱吸收范围四个方面,综述了提高体异质结聚合物太阳电池能量转化效率的方法。     

Material Solubility‐Photovoltaic Performance Relationship in the Design of Novel Fullerene Derivatives for Bulk Heterojunction Solar Cells

The preparation of 27 different derivatives of C₆₀ and C₇₀ fullerenes possessing various aryl (heteroaryl) and/or alkyl groups that are appended to the fullerene cage via a cyclopropane moiety and their use in bulk heterojunction polymer solar cells is reported. It is shown that even slight variations in the molecular structure of a compound can cause a significant change in its physical properties, in particular its solubility in organic solvents. Furthermore, the solubility of a fullerene derivative strongly affects the morphology of its composite with poly(3‐hexylthiophene), which is commonly used as active material in bulk heterojunction organic solar cells. As a consequence, the solar cell parameters strongly depend on the structure and the properties of the fullerene‐based material. The power conversion efficiencies for solar cells comprising these fullerene derivatives range from negligibly low (0.02%) to considerably high (4.1%) values. The analysis of extensive sets of experimental data reveals a general dependence of all solar cell parameters on the solubility of the fullerene derivative used as acceptor component in the photoactive layer of an organic solar cell. It is concluded that the best material combinations are those where donor and acceptor components are of similar and sufficiently high solubility in the solvent used for the deposition of the active layer.     

Film Morphology of High Efficiency Solution‐Processed Small‐Molecule Solar Cells

Morphological control over the bulk heterojunction (BHJ) microstructure of a high‐efficiency small molecule photovoltaic system is demonstrated using both thermal treatment and solvent additive processing. Single crystal X‐ray diffraction is utilized to understand molecular interactions in the solid state and the BHJ morphology is examined using bright field, high‐resolution, and cross‐section transmission electron microscopy techniques. Controlling the domain size, while maintaining good molecular order within the semiconducting donor material, is found to be crucial in achieving high performance and over 90% internal quantum efficiency exhibited under the optimized conditions.     

Printable and Large‐Area Organic Solar Cells Enabled by a Ternary Pseudo‐Planar Heterojunction Strategy

Bulk heterojunction (BHJ) processing technology has had an irreplaceable role in the development of organic solar cells (OSCs) in the past decades due to the significant advantages in achieving high‐power conversion efficiency (PCE). However, the difficulty in exploring and regulating morphology makes it inadequate for upscaling large‐area OSCs. In this work, printable high‐performance ternary devices are fabricated by a pseudo‐planar heterojunction (PPHJ) strategy. The fullerene derivative indene‐C₆₀ bisadduct (ICBA) is incorporated into PM6/IT‐4F system to expand the vertical phase separation and facilitate an obvious PPHJ structure. After the addition of ICBA, the IT‐4F enriches on the surface of active layer, while PM6 is accumulated underneath. Furthermore, it increases the crystallinity of PM6, which facilitates exciton dissociation and charge transfer. Accordingly, 1.05 cm² devices are fabricated by blade‐coating with an enhanced PCE of 14.25% as compared to the BHJ devices (13.73%). The ternary PPHJ strategy provides an effective way to optimize the vertical phase separation of organic semiconductor during scalable printing methods.     

Quantifying Interfacial Electric Fields and Local Crystallinity in Polymer–Fullerene Bulk‐Heterojunction Solar Cells

The challenges of experimentally probing the physical and electronic structures of the highly intermixed organic semiconductor blends that comprise active layers in high‐performance organic photovoltaic (OPV) cells ultimately limit the fundamental understanding of the device performance. We use Fourier‐transform IR (FTIR)‐absorption spectroscopy to quantitatively determine the interfacial electric field in blended poly(3‐hexylthiophene) (P3HT):phenyl‐ C61‐butyric acid methyl ester (PCBM) thin films. The interfacial electric field is ≈0.2 V nm^?1 in the as‐spun film and blends annealing at temperatures as high as 150 °C, which is the optimal annealing temperature in terms of OPV performance. The field decreases to a negligible value upon further annealing to 170 °C, at which temperature PCBM changes from amorphous to crystalline and the open‐circuit voltage of the solar cell decreases from 0.62 to 0.4 V. In addition, our measurements also allow determination of the absolute degree of crystallinity within the acceptor material. The roles of interfacial field and local crystallinity in OPV device performance are discussed.     

Fabrication,Optical Modeling,and Color Characterization of Semitransparent Bulk‐Heterojunction Organic Solar Cells in an Inverted Structure

Semitransparent inverted organic photodiodes are fabricated with a Baytron PH500 ethylene‐glycol layer/silver grid as the top electrode. Reasonable performances are obtained under both rear‐ and front‐side illumination and efficiencies up to 2% are achieved. Some light is shed on visual prospects through optical simulations for a semitransparent device of poly(3‐hexylthiophene) (P3HT) and the C60 derivative 1‐(3‐methoxycarbonyl)propyl‐1‐phenyl[6,6]C₇₁ (PC70BM) in the inverted structure. These calculations allow the maximum efficiency achievable to be predicted for semitransparent cells based on P3HT:PC70BM versus the transparency perception for a human eye. The simulations suggest that low‐bandgap materials such as poly[2,6‐(4,4‐bis‐(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b′]dithiophene)‐alt‐4,7‐(2,1,3‐benzothiadiazole)] (PCPDTBT) have a better potential for semitransparent devices. In addition, the color range recognized by the human eye is predicted by the optical simulation for some semitransparent devices including different active layers.     

Nanostructure and Optoelectronic Characterization of Small Molecule Bulk Heterojunction Solar Cells by Photoconductive Atomic Force Microscopy

Photoconductive atomic force microscopy is employed to study the nano­scale morphology and optoelectronic properties of bulk heterojunction solar cells based on small molecules containing a benzofuran substituted diketopyrrolopyrrole ( DPP ) core (3,6‐bis(5‐(benzofuran‐2‐yl)thiophen‐2‐yl)‐2,5‐bis(2‐ethylhexyl)pyrrolo[3,4‐c]pyrrole‐1,4‐dione, DPP(TBFu)₂ , and [6,6]–phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) , which were recently reported to have power conversion efficiencies of 4.4%. Electron and hole collection networks are visualized for blends with different donor:acceptor ratios. Formation of nanostructures in the blends leads to a higher interfacial area for charge dissociation, while maintaining bicontinuous collection networks; conditions that lead to the high efficiency observed in the devices. An excellent agreement between nanoscale and bulk open‐circuit voltage measurements is achieved by surface modification of the indium tin oxide (ITO) substrate by using aminopropyltrimethoxysilane. The local open‐circuit voltage is linearly dependent on the cathode work function. These results demonstrate that photoconductive atomic force microscopy coupled with surface modification of ITO substrate can be used to study nanoscale optoelectronic phenomena of organic solar cells.     

高效率n-nc-Si:H/p-c-Si异质结太阳能电池

采用热丝化学气相沉积技术(HWCVD),系统地研究了纳米晶硅层(尤其是本征缓冲层)的晶化度以及晶体硅表面氢处理时间对nc-Si∶H/c-Si异质结太阳能电池性能的影响,通过C-V和C-F测试分析了不同氢处理时间和本征缓冲层氢稀释度对nc-Si∶H/c-Si界面缺陷态的影响,运用高分辨透射电镜观察了不同的本征缓冲层晶化度的nc-Si∶H/c-Si异质结太阳能电池的界面,优化工艺参数,在p型CZ晶体硅衬底上制备出转换效率为17.27%的n-nc-Si∶H/i-nc-Si∶H/p-c-Si异质结电池.     

高效率n-nc-Si∶H/p-c-Si异质结太阳能电池

采用热丝化学气相沉积技术(HWCVD),系统地研究了纳米晶硅层(尤其是本征缓冲层)的晶化度以及晶体硅表面氢处理时间对nc-Si∶H/c-Si异质结太阳能电池性能的影响,通过C-V和C-F测试分析了不同氢处理时间和本征缓冲层氢稀释度对nc-Si∶H/c-Si界面缺陷态的影响,运用高分辨透射电镜观察了不同的本征缓冲层晶化度的nc-Si∶H/c-Si异质结太阳能电池的界面,优化工艺参数,在p型CZ晶体硅衬底上制备出转换效率为17.27%的n-nc-Si∶H/i-nc-Si∶H/p-c-Si异质结电池.     

Ambient Layer‐by‐Layer ZnO Assembly for Highly Efficient Polymer Bulk Heterojunction Solar Cells

The use of metal oxide interlayers in polymer solar cells has great potential because metal oxides are abundant, thermally stable, and can be used in flexible devices. Here, a layer‐by‐layer (LbL) protocol is reported as a facile, room‐temperature, solution‐processed method to prepare electron transport layers from commercial ZnO nanoparticles and polyacrylic acid (PAA) with a controlled and tunable porous structure, which provides large interfacial contacts with the active layer. Applying the LbL approach to bulk heterojunction polymer solar cells with an optimized ZnO layer thickness of ≈25 nm yields solar cell power‐conversion efficiencies (PCEs) of ≈6%, exceeding the efficiency of amorphous ZnO interlayers formed by conventional sputtering methods. Interestingly, annealing the ZnO/PAA interlayers in nitrogen and air environments in the range of 60–300 °C reduces the device PCEs by almost 20% to 50%, indicating the importance of conformational changes inherent to the PAA polymer in the LbL‐deposited films to solar cell performance. This protocol suggests a new fabrication method for solution‐processed polymer solar cell devices that does not require postprocessing thermal annealing treatments and that is applicable to flexible devices printed on plastic substrates.