Open‐Circuit Voltage and Effective Gap of Organic Solar Cells

The open‐circuit voltage (V_OC) of an organic solar cell is limited by the donor‐acceptor material system. The effective gap E_g^eff between the electron affinity of the acceptor and the ionization potential of the donor is usually regarded as the upper limit for V_OC, which is only reached for T → 0 K. This relation is confirmed for a number of small‐molecule bulk heterojunction p‐i‐n type solar cells by varying the temperature and illumination intensity. With high precision, the low temperature limit of V_OC is identical to E_g^eff. Furthermore, the influence of the hole transport material in a p‐doped hole transport layer and the donor‐acceptor mixing ratio on this limit V₀ is found to be negligible. Varying the active material system, the quantitative relation between V₀ and E_g^eff is found to be identity. A comparison of V₀ in a series of nine different donor‐acceptor material combinations opens a pathway to quantitatively determine the ionization potential of a donor material or the electron affinity of an acceptor material.     

Recent Progress in Flexible and Stretchable Organic Solar Cells

Flexible and stretchable organic solar cells (OSCs) have attracted enormous attention due to their potential applications in wearable and portable devices. To achieve flexibility and stretchability, many efforts have been made with regard to mechanically robust electrodes, interface layers, and photoactive semiconductors. This has greatly improved the performance of the devices. State‐of‐the‐art flexible and stretchable OSCs have achieved a power conversion efficiency of 15.21% (16.55% for tandem flexible devices) and 13%, respectively. Here, the recent progress of flexible and stretchable OSCs in terms of their components and processing methods are summarized and discussed. The future challenges and perspectives for flexible and stretchable OSCs are also presented.     

Nongeminate Recombination and Charge Transport Limitations in Diketopyrrolopyrrole‐Based Solution‐Processed Small Molecule Solar Cells

Charge transport and nongeminate recombination are investigated in two solution‐processed small molecule bulk heterojunction solar cells consisting of diketopyrrolopyrrole (DPP)‐based donor molecules, mono‐DPP and bis‐DPP, blended with [6,6]‐phenyl‐C71‐butyric acid methyl ester (PCBM). While the bis‐DPP system exhibits a high fill factor (62%) the mono‐DPP system suffers from pronounced voltage dependent losses, which limit both the fill factor (46%) and short circuit current. A method to determine the average charge carrier density, recombination current, and effective carrier lifetime in operating solar cells as a function of applied bias is demonstrated. These results and light intensity measurements of the current‐voltage characteristics indicate that the mono‐DPP system is severely limited by nongeminate recombination losses. Further analysis reveals that the most significant factor leading to the difference in fill factor is the comparatively poor hole transport properties in the mono‐DPP system (2 × 10^?5 cm² V^?1 s^?1 versus 34 × 10^?5 cm² V^?1 s^?1). These results suggest that future design of donor molecules for organic photovoltaics should aim to increase charge carrier mobility thereby enabling faster sweep out of charge carriers before they are lost to nongeminate recombination.     

Activation Energy Spectra: Insights into Transport Limitations of Organic Semiconductors and Photovoltaic Cells

Some mechanisms of charge transport in organic semiconductors and organic photovoltaic (OPV) cells can be distinguished by their predicted change in activation energy for the current, E_a, versus applied field, F. E_a versus F is measured first in pure films of commercially available regioregular poly(3‐hexylthiophene) (P3HT) and in the same P3HT treated to reduce its charged defect density. The former shows a Poole–Frenkel (PF)‐like decrease in E_a at low F, which then plateaus at higher F. The low defect material does not exhibit PF behavior and E_a remains approximately constant. Upon addition of [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM), however, both materials show a large increase in E_a and exhibit PF‐like behavior over the entire field range. These results are explained with a previously proposed model of transport that considers both the localized random disorder in the energy levels and the long‐range electrostatic fluctuations resulting from charged defects. Activation energy spectra in working OPV cells show that the current is injection‐limited over most of the voltage range but becomes transport‐limited, with a large peak in E_a, near the open circuit photovoltage. This causes a decrease in fill factor, which may be a general limitation in such solar cells.     

NiOX/MoO3 Bi‐Layers as Efficient Hole Extraction Contacts in Organic Solar Cells

The electronic structure of a bi‐layer hole extraction contact consisting of nickel oxide (NiO_x) and molybdenum trioxide (MoO₃) is determined via ultraviolet and X‐ray photoemission spectroscopy. The bi‐layer presents ideal energetics for the extraction of holes and suppression of carrier recombination at the interface. The application of the NiO_x/MoO₃ bi‐layer as the anode of organic bulk heterojunction solar cells based on PCDTBT/PC₇₁BM leads to improved device performance, which is explained by an intricate charge transfer process across the interface.     

Enhanced Performance in Polymer Solar Cells by Surface Energy Control

Enhanced performance of an inverted‐type polymer solar cell is reported by controlling the surface energy of a zinc oxide (ZnO) buffer layer, on which a photoactive layer composed of a polymer:fullerene‐derivative bulk heterojunction is formed. With the approach based on a mixed self‐assembled monolayer, the surface energy of the ZnO buffer layer can be controlled between 40 mN m^?1 and 70 mN m^?1 with negligible changes in its work function. For the given range of surface energy the power conversion efficiency increases from 3.27% to 3.70% through enhanced photocurrents. The optimized morphology obtained by surface energy control results in the enhanced photocurrent and transmission electron microscopy analysis verifies the correlation between the surface energy and the phase morphology of the bulk heterojunction. These results demonstrate that surface energy control is an effective method for further improving the performance of polymer solar cells, with potentially important implications for other organic devices containing an interface between a blended organic active layer and a buffer or an electrode layer.     

Amorphous Zinc Stannate (Zn2SnO4) Nanofibers Networks as Photoelectrodes for Organic Dye‐Sensitized Solar Cells

A new strategy for developing dye‐sensitised solar cells (DSSCs) by combining thin porous zinc tin oxide (Zn₂SnO₄) fiber‐based photoelectrodes with purely organic sensitizers is presented. The preparation of highly porous Zn₂SnO₄ electrodes, which show high specific surface area up to 124 m²/g using electrospinning techniques, is reported. The synthesis of a new organic donor‐conjugate‐acceptor (D‐π‐A) structured orange organic dye with molar extinction coefficient of 44 600 M^?1 cm^?1 is also presented. This dye and two other reference dyes, one organic and a ruthenium complex, are employed for the fabrication of Zn₂SnO₄ fiber‐based DSSCs. Remarkably, organic dye‐sensitized DSSCs displayed significantly improved performance compared to the ruthenium complex sensitized DSSCs. The devices based on a 3 μm‐thick Zn₂SnO₄ electrode using the new sensitizer in conjunction with a liquid electrolyte show promising photovoltaic conversion up to 3.7% under standard AM 1.5G sunlight (100 mW cm^?2). This result ranks among the highest reported for devices using ternary metal oxide electrodes.     

On the Role of Bathocuproine in Organic Photovoltaic Cells

The effect of bathocuproine (BCP) on the optical and electrical properties of organic planar heterojunction photovoltaic cells is quantified by current–voltage characterization under 1 sun AM 1.5D simulated solar illumination and spectral response at short‐circuit conditions. By inserting a 10 nm BCP layer in an indium tin oxide (ITO)/subphthalocyanine (SubPc)/buckminsterfullerene (C₆₀)/BCP/Al thin‐film structure, an increase in power‐conversion efficiency from 0.05 to 3.0% is observed, mostly reflected in the enhanced open‐circuit voltage up to 920 mV. Furthermore, the incorporation of a 10‐nm BCP layer in an ITO/C₆₀/BCP/Al structure leads to an increase in built‐in potential from 250 to 850 mV, as demonstrated by electroabsorption. It is argued that BCP passivates C₆₀ such that a 10‐nm layer provides a sufficient buffer layer that prohibits Al contacting the C₆₀ where it would otherwise create donor states.     

Charge Density Dependent Nongeminate Recombination in Organic Bulk Heterojunction Solar Cells

Apparent recombination orders exceeding the value of two expected for bimolecular recombination have been reported for organic solar cells in various publications. Two prominent explanations are bimolecular losses with a carrier concentration dependent prefactor due to a trapping limited mobility and protection of trapped charge carriers from recombination by a donor–acceptor phase separation until re‐emission from these deep states. In order to clarify which mechanism is dominant temperature‐ and illumination‐dependent charge extraction measurements are performed under open circuit and short circuit conditions at poly(3‐hexylthiophene‐2,5‐diyl):[6,6]‐phenyl‐C₆₁ butyric acid methyl ester (P3HT:PC₆₁BM) and PTB7:PC₇₁BM (poly[[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl]]) solar cells in combination with current–voltage characteristics. It is shown that the charge carrier density n dependence of the mobility μ and the recombination prefactor are different for P3HT:PC₆₁BM at temperatures below 300 K and PTB7:PC₇₁BM at room temperature. Therefore, in addition to μ(n), a detrapping limited recombination in systems with at least partial donor–acceptor phase separation is required to explain the high recombination orders.     

Triplet Exciton and Polaron Dynamics in Phosphorescent Dye Blended Polymer Photovoltaic Devices

The triplet exciton and polaron dynamics in phosphorescent dye (PtOEP) blended polymer (MEH‐PPV) photovoltaic devices are investigated by quasi‐steady‐state photo‐induced absorption (PIA) spectroscopy. According to the low‐temperature PIA and photoluminescence (PL) results, the increase in strength of the triplet‐triplet (T₁‐T_n) absorption of MEH‐PPV in the blend system originates from the triplet‐triplet energy transfer from PtOEP to MEH‐PPV. The PtOEP blended MEH‐PPV/C₆₀ bilayer photovoltaic device shows a roughly 30%–40% enhancement in photocurrent and power‐conversion efficiency compared to the device without PtOEP. However, in contrast to the bilayer device results, the bulk heterojunction photovoltaic devices do not show a noticeable change in photocurrent and power‐conversion efficiency in the presence of PtOEP. The PIA intensity, originating from the polaron state, is only slightly higher (within the experimental error), indicating that carrier generation in the bulk heterojunction is not enhanced in the presence of PtOEP. The rate and probability of the exciton dissociation between PtOEP and PCBM is much faster and higher than that of the triplet‐triplet energy transfer between PtOEP and MEH‐PPV.     

Imaging the Electric Potential within Organic Solar Cells

The charge transport in organic solar cells is investigated by surface potential measurements via scanning Kelvin probe microscopy. Access to the solar cell's cross‐section is gained by milling holes with a focused ion beam which enables the direct scan along the charge transport path. In a study of poly(3‐hexylthiophene):1‐(3‐methoxycarbonyl)propyl‐1‐phenyl[6,6]C61 (P3HT:PCBM) bulk heterojunction solar cells, the open circuit voltage is built up at the top contact. A comparison of the potential distribution within normal and inverted solar cells under operation exhibits strongly different behaviors, which can be assigned to a difference in interface properties.     

Triplet Formation in Fullerene Multi‐Adduct Blends for Organic Solar Cells and Its Influence on Device Performance

In organic solar cells, high open circuit voltages may be obtained by choosing materials with a high offset between the donor highest occupied molecular orbital (HOMO) and acceptor lowest unoccupied molecular orbital (LUMO). However, increasing this energy offset can also lead to photophysical processes that compete with charge separation. In this paper the formation of triplet states is addressed in blends of polyfluorene polymers with a series of PCBM multi‐adducts. Specifically, it is demonstrated that the formation of such triplets occurs when the offset energy between donor ionization potential and acceptor electron affinity is ～1.6 eV or greater. Spectroscopic measurements support a mechanism of resonance energy transfer for triplet formation, influenced by the energy levels of the materials, but also demonstrate that the competition between processes at the donor–acceptor interface is strongly influenced by morphology.     

Polymer/Nanocrystal Hybrid Solar Cells: Influence of Molecular Precursor Design on Film Nanomorphology,Charge Generation and Device Performance

In this work, molecular tuning of metal xanthate precursors is shown to have a marked effect on the heterojunction morphology of hybrid poly(3‐hexylthiophene‐2,5‐diyl) (P3HT)/CdS blends and, as a result, the photochemical processes and overall performance of in situ fabricated hybrid solar cells. A series of cadmium xanthate complexes is synthesized for use as in situ precursors to cadmium sulfide nanoparticles in hybrid P3HT/CdS solar cells. The formation of CdS domains is studied by simultaneous GIWAXS (grazing incidence wide‐angle X‐ray scattering) and GISAXS (grazing incidence small‐angle X‐ray scattering), revealing knowledge about crystal growth and the formation of different morphologies observed using TEM (transmission electron microscopy). These measurements show that there is a strong relationship between precursor structure and heterojunction nanomorphology. A combination of TAS (transient absorption spectroscopy) and photovoltaic device performance measurements is used to show the intricate balance required between charge photogeneration and percolated domains in order to effectively extract charges to maximize device power conversion efficiencies. This study presents a strong case for xanthate complexes as a useful route to designing optimal heterojunction morphologies for use in the emerging field of hybrid organic/inorganic solar cells, due to the fact that the nanomorphology can be tuned via careful design of these precursor materials.     

Enhanced Thermal Stability and Efficiency of Polymer Bulk‐Heterojunction Solar Cells by Low‐Temperature Drying of the Active Layer

This study addresses two key issues, stability and efficiency, of polymer solar cells based on blended poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) by demonstrating a film‐forming process that involves low‐temperature drying (?5 °C) and subsequent annealing of the active layer. The low‐temperature process achieves 4.70% power conversion efficiency (PCE) and ～1250 h storage half‐life at 65 °C, which are significant improvements over the 3.39% PCE and ～143 h half‐life of the regular room‐temperature process. The improvements are attributed to the enhanced nucleation of P3HT crystallites as well as the minimized separation of the P3HT and PCBM phases at the low drying temperature, which upon post‐drying annealing results in a morphology consisting of small PCBM‐rich domains interspersed within a densely interconnected P3HT crystal network. This morphology provides ample bulk‐heterojunction area for charge generation while allowing for facile charge transport; moreover, the P3HT crystal network serves as an immobile frame at heating temperatures less than the melting point (T_m) of P3HT, thus preventing PCBM/P3HT phase separation and the corresponding device degradation.     

Efficient Organic Photovoltaic Cells Based on Nanocrystalline Mixtures of Boron Subphthalocyanine Chloride and C60

The electrical and structural behavior of uniformly mixed films of boron subphthalocyanine chloride (SubPc) and C₆₀ and their performance in organic photovoltaic cells is explored. Device performance shows a strong dependence on active‐layer donor–acceptor composition, and peak efficiency is realized at 80 wt.% C₆₀. The origin of this C₆₀‐rich optimum composition is elucidated in terms of morphological changes in the active layer upon diluting SubPc with C₆₀. While neat SubPc is found to be amorphous, mixed films containing 80 wt.% C₆₀ show clear nanocrystalline domains of SubPc. Supporting electrical characterization indicates that this change in morphology coincides with an increase in the hole mobility of the SubPc:C₆₀ mixture, with peak mobility observed at a composition of 80 wt.% C₆₀. Organic photovoltaic cells constructed using this optimum SubPc:C₆₀ ratio realize a power conversion efficiency of (3.7 ± 0.1)% under 100 mW cm^?2 simulated AM1.5G solar illumination.     

Intrinsically Stretchable Organic Solar Cells beyond 10% Power Conversion Efficiency Enabled by Transfer Printing Method

Stretchable organic solar cells (OSCs) simultaneously possessing high-efficiency and robust mechanical properties are ideal power generators for the emerging wearable and portable electronics. Herein, after incorporating a low amount of trimethylsiloxy terminated polydimethylsiloxane (PDMS) additive, the intrinsic stretchability of PTB7-Th:IEICO-4F bulk heterojunction (BHJ) film is greatly improved from 5% to 20% strain without sacrificing the photovoltaic performance. The intimate multi-layers stacking of OSCs is also realized with the transfer printing method assisted by electrical adhesive “glue” D-Sorbitol. The resultant devices with 84% electrode transmittance exhibit a remarkable power conversion efficiency (PCE) of 10.1%, which is among the highest efficiency for intrinsically stretchable OSCs to date. The stretchable OSCs also demonstrate the ultra-flexibility, stretchability, and mechanical robustness, which keep the PCE almost unchanged at small bending radium of 2 mm for 300 times bending cycles and retain 86.7% PCE under tensile strain as large as 20% for the devices with 70% electrode transmittance. The results provide a universal method to fabricate highly efficient intrinsically stretchable OSCs.     

Comparison of Two D−A Type Polymers with Each Being Fluorinated on D and A Unit for High Performance Solar Cells

For the purpose of investigating the effect of fluorination position on D?A type conjugated polymer on photophysical and photovoltaic properties, two types of fluorinated polymere are synthesized, HF with fluorination on electron‐donating unit and FH with fluorination on electron‐accepting unit. Compared to non‐fluorinated polymer, fluorinated polymers exhibit deeper HOMO energy levels without change of bandgap and stronger vibronic shoulder in UV?visible absorption, indicating that fluorination enhances intermolecular interaction. HF with fluorinated D unit exhibits well‐developed fibril network, low bimolecular recombination and high hole mobility, which lead a high PCE of 7.10% in conventional single‐junction solar cells, which is higher than the PCE (6.41%) of FH with fluorinated A unit. Therefore, this result demonstrates that fluorination on electron‐donating unit in D?A polymers could be a promising strategy for achieving high performance polymer solar cells.     

Role of PbSe Structural Stabilization in Photovoltaic Cells

Semiconductor nanocrystals are promising materials for printed optoelectronic devices, but their high surface areas are susceptible to forming defects that hinder charge carrier transport. Furthermore, correlation of chalcogenide nanocrystal (NC) material properties with solar cell operation is not straightforward due to the disorder often induced into NC films during processing. Here, an improvement in long‐range ordering of PbSe NCs symmetry that results from halide surface passivation is described, and the effects on chemical, optical, and photovoltaic device properties are investigated. Notably, this passivation method leads to a nanometer‐scale rearrangement of PbSe NCs during ligand exchange, improving the long‐range ordering of nanocrystal symmetry entirely with inorganic surface chemistry. Solar cells constructed with a variety of architectures show varying improvement and suggest that triplet formation and ionization, rather than carrier transport, is the limiting factor in singlet fission solar cells. Compared to existing protocols, our synthesis leads to PbSe nanocrystals with surface‐bound chloride ions, reduced sub‐bandgap absorption and robust materials and devices that retain performance characteristics many hours longer than their unpassivated counterparts.