含活性基团硅氮烷先驱体的裂解

用ＴＧ－ＧＣ，ＩＲ，元素分析，ＸＲＤ研究ＭｅＳｉＨＣｌ２与ＭｅＳｉＶｉ（Ｖｉ：－ＣＨ＝ＣＨ２）Ｃｌ２共氨解产物的裂解过程。     

STUDY FOR MECHANICAL ALLOYING OF Fe─M BY MOSSBAUER SPECTROSCOPY

将Ｆｅ－Ｍ（Ｍ＝Ｃ５ＳｉＯ２Ａｌ２Ｏ３）混合物在Ａｒ中高能球磨５６ｇ后测量Ｍｏｓｂａｕｅｒ谱，结果表明，（Ｆｅ）２－（ＳｉＯ２）１仍为Ｆｅ和ＳｉＯ２的机械混合物：（Ｆｅ）６－（Ｃ）３已完全合金化，生成两种Ｆｅ３Ｃ；（Ｆｅ）２－（Ａｌ２Ｏ３）１则成为Ｆｅ（７３％），尖晶石型的ＦｅＡｌ２Ｏ４）２２％），ｑｑｎｔＦｅ的团聚族（５％）和Ａｌ２Ｏ３的混合物。     

1,3-戊二烯阳离子聚合引发体系(CH3)3SiCl/EtAlCl2的研究

研究了阳离子引发体系Ｍｅ３ＳｉＣｌ（ＴＭＳＣｌ）ＥｔＡｌＣＬ２在正己烷中引发的１,３－戊二烯（ＰＤ）聚合反应。研究结果表明,在ＥｔＡｌＣｌ２引发的ＰＤ聚合反应中引入ＴＭＳＣｌ后大幅主提高了聚合物产率,同时使聚合反应速率明显提高,在「ＴＭＳＣｌ」／「ＥｔＡｌＣｌ２２」＝０－１范围内,ＴＭＳＣｌ／ＥｔＡｌＣｌ２体系制备的聚合物分子量高于ＥｔＡｌＣｌ２引发制备的聚合物,这些结果表明Ｍｅ３ＳｉＣｌ／ＥｔＡ     

Al—Si—Cu—Mg系合金W（AlxSi4Mg5Cu4）相与Al2Cu相的显示与鉴别

研究了Ａｌ－Ｓｉ－Ｃｕ－Ｍｇ系中富铜的Ｗ（ＡｌｘＳｉ４Ｍｇ５Ｃｕ４）相与Ａｌ２Ｃｕ相的金相显示鉴别法，并用化学染色试剂彩色显示区分铸造铝硅铜镁系合金（α＋Ｓｉ＋Ａｌ２Ｃｕ＋Ｗ）四元共晶中的Ｗ相及Ａｌ２Ｃｕ相。     

碳纤维增强C—SiC梯度基复合材料研究

采用ＣＶＩ工艺均热法共沉积技术制备了碳纤维增强Ｃ－ＳｉＣ梯度基复合材料。Ｃ和ＳｉＣ的原料氛分别是Ｃ２Ｈ２ｔ ＣＨ３ＳｉＣｌ３，Ａｒ和Ｈ２分别是载流和稀释气体。基体微观结构的变化通过控制原料气体的成分配比藜得。测试了材料的力学性能、抗氧化性能和摩擦磨损性能。利用金相技术、电子探针成分分析技术、ＴＥＭ和ＳＥＭ技术观察和分析了材料的微观结构。试验结果表明，这种材料的组织结构特点是：在微观上是梯度的，即围     

三价铈离子在氯硅酸镁钙中的晶体学格位研究

首次合成了发射蓝紫光的Ｃｅ＾３＋激活的氯硅酸镁钙ＣａｇＭｇ（ＳｉＯ４）４Ｃｌ２：Ｃｅ＾３＋新荧光粉,利用Ｃｅ＾３＋的光谱结果和Ｖａｎ Ｕｉｔｅｒｔ经验公式,结合对ＣａｇＭｇ（ＳｉＯ４）４Ｃｌ２晶体的结构研究,判断出ＣａｇＭｇ（ＳｉＯ４）４Ｃｌ２：Ｃｅ＾３＋中存在两种性质稍有差异的Ｃｅ＾３＋发光中心,这两种发光中心均占据其质中八配位的钙格位。     

添加Al_2O_3对SiC板粒／Y－TZP复合材料力学性能的影响

本文以ＳｉＣ板粒、ＺｒＯＣｌ２－８Ｈ２Ｏ、ＡｌＣｌ３和Ｙ（ＭＯ）３为原料，利用共沉淀和热压烧结工艺，制备ＳｉＣ板粒／Ｙ－ＴＺＰ和（含Ａｌ２Ｏ３）ＳｉＣ板粒／Ｙ－ＴＺＰ复合材料．测试了材料的室温和高温力学性能．研究了添加Ａｌ２Ｏ３对ＳｉＣ板粒／Ｙ－ＴＺＯ复合材料的影响．结果表明，ＳｉＣ板粒／Ｙ－ＴＺＰ复合材料与Ｙ－ＴＺＰ陶瓷相比，其室温强度和韧性出现明显下降，高温强度也没有改善；而在ＳｉＣ板粒与Ｙ－ＴＺＰ复合的基础上，添加Ａｌ２Ｏ３可明显提高材料的强度和断裂韧性，同时，材料的高温强度也获得显著改善．     

添加Al2O3对SiC板粒／Y—TZP复合材料力学性能的影响

本以ＳｉＣ板粒、ＺｒＯＣｌ２·８Ｈ２Ｏ、ＡｌＣｌ３和Ｙ（ＭＯ）３为原料，利用共沉淀和热压烧结工艺，制备ＳｉＣ板粒／Ｙ－ＴＺＰ和（含Ａｌ２Ｏ３）ＳｉＣ板粒／Ｙ－ＴＺＰ复合材料。测试了材料的室温和高温力学性能。研究了添加Ａｌ２Ｏ３对ＳｉＣ板粒／Ｙ－ＴＺＯ复合材料的影响。结果表明，ＳｉＣ板粒／Ｙ－ＴＺＰ复合材料与Ｙ－ＴＺＰ复合材料与Ｙ－ＴＺＰ陶瓷相比，其室温强度和韧性出现明显下降，高温强度也没有改善；     

气相反应法合成超细粉末过程中的r~＊叶和晶型的研究

本文以ＳｉＣｌ４－ＮＨ３、ＳｉＣｌ４－Ｏ２、ＳｉＣｌ４－Ｎ２－Ｈ２、ＴｉＣｌ４－ＮＨ３－Ｈ２、ＴｉＣｌ４－Ｎ２－Ｈ２、ＴｉＣｌ４－Ｏ２、ＡｌＣｌ３－Ｏ２等为体系，运用均匀成核理论，研究了平衡常数Ｋｐ、过饱和比Ｓ及临界核半径，ｒ＊等因素对气相反应法中超细粉末的形成及粉末结构状态的影响．结果表明，当２ｒ＊大于某物质的晶格常数时，用气相反应法得到的该物质的超细粉末一般为晶体粉末，反之则得到无定形粉末．     

碳化硅和氧化铝陶瓷的热等静压氮化

通过对无压烧结、热压烧结和热等静压烧结ＳＩＣ陶瓷以及热压烧结的ＳｉＣ粒子补强Ａｌ２Ｏ３基复相陶瓷（ＳｉＣｐ－Ａｌ２Ｏ３）和ＳｉＣ粒子与ＳｉＣ晶须共同增强的Ａｌ２Ｏ３基复合材料（ＳｉＣｐ－ＳｉＣｗ－Ａｌ２Ｏ３）在氮气氛中进行高温氮化处理，成功地实现了这些材料的开口气孔表面裂纹的愈合。研究表明：热等静压氯化工艺可以显著提高ＳｉＣ和Ａｌ２Ｏ３陶瓷的抗弯强度，对断裂韧性也有较大的改善作用。对于热等静压烧结ＳｉＣ陶瓷，在１８５０℃和２００ＭＰａ氮气压力下氯化处理１小时后，其抗弯强度和断裂韧性分别由５８２ＭＰａ和５．７ＭＰａ·ｍ１／２提高到９０７ＭＰａ和８．４ＭＰａ·ｍ１／２；对于热压烧结的ＳｉＣｐ－Ａｌ２Ｏ３复相陶瓷和ＳｉＣｐ－ＳｉＣｗ－Ａｌ２Ｏ３复合材料，在１７００℃和１５０ＭＰａ氮气压力下氮化处理１小时后，其室温抗弯强度分别由４６０和７０５ＭＰａ提高到８９５和１０３３ＭＰａ。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.