Hyperbranched poly(arylene ether phosphine oxide)s

Summary New AB₂ and A₂B monomers, bis(4-fluorophenyl)-4'-hydroxyphenylphosphine oxide and bis(4-hydroxyphenyl)-4'-fluorophenyl-phosphine oxide were prepared and converted to corresponding hyperbranched poly(arylene ether phosphineoxide)s with hydroxyphenyl and fluorophenyl end functional groups. While the dihydroxy monomer gave a low molecular weight polymer, the difluoro monomer produced a high molecular weight hyperbranched polymer. The glass transition temperature of the obtained polymers was 266°C and 230°C, and 5% weight loss temperature was 491 °C and 391 °C, respectively. The fluorophenyl-terminated hyperbranched polymer was soluble in CHCl₃, but the hydroxyphenyl-terminated polymer was not soluble in CHCl3 even though it has lower molecular weight than the fluorophenyl-terminated polymer, indicating that properties of the hyperbranched polymers markedly depend on end functional groups as well as their molecular weight. Received: 23 August 2000/Revised version: 19 October 2000/Accepted: 31 October 2000     

Synthesis of new poly(aryl ether)s with pendent benzoxazole groups via Ullmann ether reaction

A study has been done on the synthesis of new poly(aryl ether)s with two pendent benzoxazole groups via Ullmann condensation reaction. As a new rigid monomer, 1,4-bis(2-benzoxazolyl)-2,5-dibromobenzene ( II ) was synthesized in a two-step reaction starting from 2,5-dibromo-p-xylene. A model reaction of aryl dibromide II with two equivalents of m-cresol under Ullmann reaction conditions gave very high yield of the substitution product III , suggesting the possibility of producing polyethers in this system. The aryl dibromide monomer was polymerized with two different bisphenols (bisphenol A (BPA) and 4,4'-(hexafluoroisopropylidine)diphenol (BPA-6F)) in NMP or benzophenone/pyridine via CuCl-catalysed Ullmann reaction. The molecular weights of the obtained polymers ( IV ), however, seemed relatively low according to their solution viscosity. The resulting polymers showed good solubility in many common solvents including chlorinated hydrocarbons, tetrahydrofuran, pyridine as well as typical aprotic polar solvents. The glass transition temperatures were found at 168°C ( IV-a ) and 172°C ( IV-b ), respectively, and no melting transition appeared, indicating the amorphous nature of these polymers. The polymers were stable up to 400 – 450°C as determined by the weight loss onset temperature observed by TGA.     

Cross‐Linked Fluorinated Poly(Aryl Ether) (C‐FPAE) Films: Preparation Strategy,Performance Study,and Low Dielectric Applications

The production of low dielectric materials that can be used in high temperature environments is the primary aim of this work. A cross‐linked structure is introduced into fluorinated poly(aryl ether) (named as FPAE) with high molecular weight (M_w, 140 000 g mol^?1) and linear molecular structure using nucleophilic substitution reaction at the ortho‐position of decafluorobiphenyl monomer units in the FPAE molecular chain. The curing temperature and curing time are optimized and the final conditions for the cross‐linking reaction in this study are determined to be 300 °C for 1 h. Moreover, the dielectric constant and dielectric loss of the C‐FPAE film respectively are 2.67 and 0.006 at 1000 Hz when 1 wt% of crosslinking agent is added, and the cross‐linked fluorinated poly(aryl ether) film shows excellent thermal stability (T_d(5%), 495 °C), dimensional stability, hydrophobic properties, and high storage modulus in high temperature environments. Such novel low dielectric material with excellent performances has important application value in the aerospace and the integrated electronics field.     

Poly(aryl ether oxadiazoles)

A general method for the preparation of poly(aryl ether oxadiazoles) has been developed where the generation of an aryl ether linkage was the polymer-forming reaction. Two synthetic approaches were investigated based on either an oxadiazole-activated halo displacement with phenoxides or a hydrazide-activated halo-displacement with phenoxides. The hydrazide may be subsequently thermally cyclodehydrated to the oxadiazole heterocyclic. In each case, the negative charge developed in the transition state could be stabilized through a Meisenheimer Complex, analogous to conventional activating groups (e.g., sulfone and ketone), and the electron affinity, as judged by ¹H NMR, was comparable to that of other activating groups. An appropriately substituted diarylfluoro oxadiazole was prepared and polymerized with various bisphenols in an NMP/CHP solvent mixture in the presence of K₂CO₃. High molecular weight poly(aryl ether oxadiazoles) were synthesized with viscosities ranging from 0.44 to 0.76 dL/g and Tg's in the 200°C range. Conversely, the hydrazide activated halo-displacement as a means of preparing poly(aryl ether hydrazides) was not as successful, since it appears that the hydrazide was of sufficient acidity to form a salt with K₂CO₃ preventing solubility and polymerization.     

Utilization of N,N-diethyl-3,5-difluorobenzene sulfonamide to prepare functionalized poly(arylene ether)s

A series of poly(arylene ether)s carrying a pendant diethyl sulfonamide group was prepared by the meta activated nucleophilic aromatic substitution reaction of a new aryl difluoride monomer, N,N-diethyl-3,5-difluorobenzene sulfonamide. The synthesis of N,N-diethyl-3,5-difluorobenzene sulfonamide was achieved via the one-step reaction of diethyl amine with commercially available 3,5-difluorobenzenesulfonyl chloride. Model reactions and NMR data indicated that the fluoride atoms were sufficiently activated by the sulfonamide group, located in the meta position, to provide access to high molecular weight poly(arylene ether)s. The corresponding poly(arylene ether)s, were prepared by reaction of N,N-diethyl-3,5-difluorobenzene sulfonamide with bisphenol A, bisphenol AF, 4,4′-biphenol, hydroquinone, resorcinol, and 4,4′-dihydroxydiphenyl ether. The polymers were characterized via NMR spectroscopy, size exclusion chromatography, thermogravimetric analysis, and differential scanning calorimetry. The sulfonamide based poly(arylene ether)s displayed moderate thermal stability with 5% weight loss temperatures ranging from 366 to 385 °C, but possessed relatively low glass transition temperatures, 72–142 °C.     

Lactic acid based poly(ester-urethanes): Use of hydroxyl terminated prepolymer in urethane synthesis

We studied a two step process for lactic acid polymerization: in the first step, the lactic acid is condensation polymerized to a low molecular weight hydroxyl terminated prepolymer and then the molecular weight is raised by joining prepolymer chains together using diisocyanate as the chain extender. The resulting polymer is a thermoplastic poly(ester-urethane). The polymer samples were carefully characterized with ¹³C-NMR, GPC, DSC, and IR. The results indicate that high conversions of lactic acid can be achieved, as well as independent control of the stereostructure, long chain branches, molecular weight average, and molecular weight distribution. Lactic acid is converted into a poly(ester-urethane) with a weight average molecular weight as high as 390,000 g/mol and a glass transition temperature of 53.7°C. The analyzed content of the monomer in the prepolymer is less than 1 mol % and the lactide content 2.4 mol %, while the final poly(ester-urethane) is essentially monomer and lactide free. The mechanical properties of the poly(ester-urethane) are comparable to those of polylactides. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 1091–1100, 1997     

Synthesis and curing behavior of macrocycle‐terminated poly(aryl ether ketone)s

BACKGROUND: The introduction of poly(ether ether ketone)‐based carbon‐fiber composites accelerated the application of poly(ether ether ketone)s in advanced composite materials. In order to improve the compatibility and processability with reinforced components, polymers with low melt viscosity are preferable. RESULTS: Novel fully aromatic macrocycle‐terminated poly(aryl ether ketone)s (MCPAEKs) were prepared by condensation of macrocyclic aryl ether ketone dimers containing hydroxyphenyl groups and fluorine end‐capped poly(aryl ether ketone) oligomers. Compared with liner poly(aryl ether ketone)s, MCPAEKs showed much lower melt viscosities at low temperature. In the presence of caesium fluoride, the crosslinking reaction of MCPAEKs afforded fully aromatic thermoset poly(aryl ether ketone)s by ring‐opening reaction. CONCLUSION: The MCPAEKs exhibited high thermal stability due to their wholly aromatic structures. After crosslinking, the glass transition temperatures and complex melt viscosities of the polymers were increased greatly. Although there was some residual cesium fluoride or phenoxides produced by ring‐opening reaction, the thermoset poly(aryl ether ketone)s obtained had good thermal stability with temperatures at 5% weight loss above 475 °C. Copyright © 2009 Society of Chemical Industry     

A novel perfluorocyclobutyl aryl ether-based graft copolymer via 2-methyl-1,4-bistrifluorovinyloxybenzene and styrene

A series of novel perfluorocyclobutyl aryl ether-containing graft copolymers with polystyrene side chains were synthesized by the combination of thermal step-growth [2π + 2π] cycloaddition polymerization of aryl bistrifluorovinyl ether monomer and atom transfer radical polymerization (ATRP) of styrene. We first synthesized a new aryl bistrifluorovinyl ether monomer of 2-methyl-1,4-bistrifluorovinyloxybenzene in two steps using commercially available 2-methylhydroquinone as starting material and the corresponding perfluorocyclobutyl aryl ether-based homopolymer with methoxyl end groups was prepared through the homopolymerization of this monomer in diphenyl ether. Next, the pendant methyls of this fluoropolymer were mono-brominated by N-bromosuccinimide and benzoyl peroxide so as to be converted to ATRP initiation groups. The targeted poly(2-methyl-1,4-bistrifluorovinyloxybenzene)-g-polystyrene with relatively narrow molecular weight distributions (M_w/M_n ≤ 1.38) was obtained by the combination of bulk ATRP of styrene at 110 °C using CuBr/bpy as catalytic system and the grafting-from strategy. These fluorine-containing graft copolymers show excellent solubility in common organic solvents.     

Polymerization of bicyclic ethers: 2. N.m.r. structure study of the polymer formed from 3-oxabicyclo[3,2,2]nonane

The polymerization of 3-oxabicyclo[3.2.2] nonane (I) was carried out in methylene chloride with phosphorus pentafluoride and epichlorohydrin at temperatures ranging from ?25° to +25°C. Slow polymerization rates were generally observed, leading to low molecular weight amorphous polymers. By ¹³C n.m.r. and ¹H n.m.r. analysis of the monomer and polymer compounds, it was possible to assign the polymer the structure of a poly(1,4-cyclohexylene-dimethylene there). By comparing the polymer n.m.r. spectra with the proton spectra of two reference compounds, it was possible to establish a microstructure for the repeating unit of the polymer in which the methylenether groups on positions 1 and 4 of the cyclohexane ring are cis to each other. A propagation scheme through oxonium ions is proposed in order to explain the formation of cis polymer.     

Synthesis,characterization and thermal degradation of poly[2‐(3‐p‐bromophenyl‐3‐methylcyclobutyl)‐2‐hydroxyethylmethacrylate]

In this work, 2‐(3‐p‐bromophenyl‐3‐methylcyclobutyl)‐2‐hydroxyethylmethacrylate (BPHEMA) [monomer] was synthesized by the addition of methacrylic acid to 1‐epoxyethyl‐3‐bromophenyl‐3‐methyl cyclobutane. The monomer and poly(BPHEMA) were characterized by FT‐IR and [¹H] and [¹³C]NMR. Average molecular weight, glass transition temperature, solubility parameter, and density of the polymer were also determined. Thermal degradation of poly[BPHEMA] was studied by thermogravimetry (TG), FT‐IR. Programmed heating was carried out at 10 °C min⁻¹ from room temperature to 500 °C. The partially degraded polymer was examined by FT‐IR spectroscopy. The degradation products were identified by using FT‐IR, [¹H] and [¹³C]NMR and GC‐MS techniques. Depolymerization is the main reaction in thermal degradation of the polymer up to about 300 °C. Percentage of the monomer in CRF (Cold Ring Fraction) was estimated at 33% in the peak area of the GC curve. Intramolecular cyclization and cyclic anhydride type structures were observed at temperatures above 300 °C. The liquid products of the degradation, formation of anhydride ring structures and mechanism of degradation are discussed. © 1999 Society of Chemical Industry     

Crosslinkable fully aromatic poly(aryl ether ketone)s bearing macrocycle of aryl ether ketone

A novel bisphenol monomer, (3-methoxy)phenylhydroquinone, was synthesized via a three-step synthetic procedure. The cyclization of the bisphenol monomer and 4,4-difluorobenzophenone was carried out under pseudo high dilution condition. Two types of fully aromatic poly(aryl ether ketone)s were prepared by copolymerization of macrocycle of aryl ether ketone (MACEK) containing hydroxyphenyl, 4,4′-(hexafluoroisopropylidene)diphenol (HFBPA), and 4,4-difluorobenzophenone. The copolymers have high molecular mass, good solubility and high glass transition temperatures. The copolymers are crosslinkable in the presence of basic initiator and the glass transition temperatures of the copolymers increased greatly after the curing. These cured copolymers exhibit excellent thermal stability, and the 5% weight loss temperatures are around 500 °C in nitrogen.     

Synthesis and properties of new aromatic polyimides containing redox‐active anthraquinone moieties

A novel anthraquinone‐containing bis(ether amine) monomer, 2,6‐bis(4‐aminophenoxy)anthraquinone, was synthesized from readily available reagents. A series of novel aromatic polyimides were prepared from the newly synthesized diamine monomer with various aromatic tetracarboxylic dianhydrides. The intermediate poly(amic acid)s had inherent viscosities of 0.67–1.12 dL g^?1, and those derived from less stiff dianhydrides could be solution‐cast and thermally cyclodehydrated into flexible and tough polyimide films. The polyimides exhibited glass transition temperatures between 270 and 297 °C, and they were fairly stable up to a temperature of 500 °C in air or nitrogen. The electrochemical and electrochromic properties of one of the polyimides were investigated. The polymer could undergo two reversible steps of electrochemical reduction, with a color change from a colorless neutral state to pink and rose‐red reduced states. © 2012 Society of Chemical Industry     

Poly(aryl ether amides): Self polymerization of an A-B monomer via amide-activated ether synthesis

Summary A synthetic approach for the preparation of poly(aryl ether amides) has been developed where the generation of an aryl ether linkage was the polymer-forming reaction. The amide moiety was found to be sufficiently electron withdrawing to activate halosubstituents, towards nucleophilic aromatic substitution polymerizations, analogous to conventional activating groups (i.e, sulfone, ketone etc.). Several new A-B monomers, 4-fluoro-N-(4-hydroxyphenyl)benzamide, 1, and 4-fluoro-N-(3-hydroxyphenyl)benzamide, 2, which contain both an amide-activated fluoro group and a phenol group were prepared and their self polymerization studied. Compounds 1 and 2 were prepared by the condensation of 4-fluorobenzoyl chloride with either 4-or 3-aminophenol, respectively. The polymerizations were carried out in an N-methyl-2-pyrrolidone (NMP)/N-cyclohexyl-2-pyrrolidone (CHP) solvent mixture in the presence of potassium carbonate. Several new high molecular weight poly(aryl ethers) were prepared by this route with Tg's in the 225 °C range.     

Synthesis and characterization of novel poly(aryl ether ketone ketone)s containing the o‐dibenzobene moiety

The synthesis of a novel chloro monomer containing the 1,2‐dibenzoylbenzene moiety was described. The chloro monomer was reacted with 4‐(4‐hydroxyphenyl)‐1(2H)‐phthalazinone compound in the presence of excess anhydrous potassium carbonate in an aprotic solvent (Sulfolane), and high molecular weight amorphous poly(aryl ether ketone ketone) was synthesized. The polymers with high glass transition temperature were soluble in solvents such as chloroform and nitrobenzene at room temperature and easily cast into flexible, colorless, and transparent films. The 5% weight loss of the polymers was >400 °C. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1487–1492, 2001     

Preparation of SBS/poly(styrene–methyl methacrylate) thermoplastic interpenetrating polymer network

SBS as polymer I, poly(styrene–methyl methacrylate) polymerized by atom transfer radical polymerization as polymer II, and a thermoplastic interpenetrating polymer network of SBS/poly(styrene–methyl methacrylate) were prepared by the sequential method. The effects of the polymerization temperature, the composition of the catalyst, the ratio of the monomers studied, and the kinetics at 90°C were also investigated. It was shown that when polymerization was initiated by a BPO/CuCl/bpy (BPO:CuCl:bpy = 1:1:3) system at 90°C, the mass averaged molecular weight of the poly(styrene–methyl methacrylate) increased with monomer conversion, and the polydispersities were kept very low. Fourier transform infrared spectroscopy and gel permeation chromatogram showed that poly(styrene–methyl methacrylate) with low polydispersities had been synthesized. Thus, a thermoplastic interpenetrating polymer network comprised of both narrow molecular‐weight‐distribution components was successfully prepared. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2007–2011, 2003     

Synthesis and characterization of a chiral copoly(ether sulfone) with high molecular weight

A series of chiral poly(ether sulfone)s containing (S)‐binaphthyl unit were synthesized via nucleophilic substitution polycondensation. The as‐synthesized polymers were characterized by NMR. The molecular weights of these polymers were calculated by viscosity and gel permeation chromatography. The thermal stability was measured by TGA. The optical activities of the polymers were studied by circular dichroism and optical rotation. It was found that introducing more reactive 2,2′‐biphenol monomer to partly substitute the binaphthol monomer could increase the molecular weight of the polymer from 4.1 × 10⁴ to 9.8 × 10⁴ g mol^?1. Meanwhile, the thermal stability increased and the decomposition temperature rose from 447 to 518 °C, with the optical activity of the polymer well preserved. However, the value of the specific optical rotation decreased with increasing biphenol to binaphthol molar ratio. In addition, the optical rotation direction of the polymer was contrary to that of the pristine binaphthol monomer, which indicated that the chiral polymers formed a secondary structure. © 2013 Society of Chemical Industry     

Synthesis and properties of new poly(ether imides) based on pyridine‐containing aromatic dianhydride and diamine monomers

A series of novel aromatic poly(ether imides) with inherent viscosities of 0.48–0.70 dL/g and weight‐average molecular weights of 18,800–40,500 g/mol were successfully prepared from two dianhydride and two diamine monomers containing pyridine moiety via both two‐step method and one‐step method. Comparison of the one‐step and the two‐step methods for the preparation of poly(ether imides) was carried out and shown that poly (ether imides) obtained via one‐step method exhibited higher molecular weights than the similar polymers prepared through two‐step process. Poly(ether imide) resins obtained via both one‐step and two‐step methods with subsequent chemical dehydration showed good solubility not only in high boiling point solvents but also in low boiling point solvents. High‐quality poly(ether imide) films could be obtained via the two‐step method with subsequent thermal imidization, which exhibited excellent thermal properties with glass transition temperatures of 239–278°C, initial decomposition temperatures of 540–574°C, residual weight percent at 800°C of 64.5–69.3% under nitrogen, good thermo‐oxidative stability with initial decomposition temperatures of 521–544°C, residual weight percent at 800°C of 33.6–51.1% under air atmosphere, outstanding mechanical properties with tensile strengths in the range of 104.6–109.4 MPa, tensile modulus in the range of 1.92–2.58 GPa, and elongation at break from 6.9 to 8.0%, as well as good transparency with cutoff wavelengths of 386–392 nm and low dielectric constants of 2.80–2.92 at 1 MHz. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of novel soluble poly(ether ketone sulfone)s with pendant polychloro groups

A novel monomer of tetrachloroterephthaloyl chloride (TCTPC) was prepared by the chlorination of terephthaloyl chloride catalyzed by ferric chloride at 175–180°C for 10 h and confirmed by FTIR, MS, and elemental analysis. Five new polychloro substituted poly(aryl ether ketone sulfone)s (PEKSs) with inherent viscosities of 0.68–0.75 dL/g have been prepared from 4,4′‐diphenoxydiphenylsulfone, 4,4′‐bis(2‐methylphenoxy) diphenylsulfone, 4,4′‐bis(3‐methylph‐enoxy)diphenylsulfone, 4,4′‐bis(2,6‐dimethylphenoxy)diphenylsulfone, and 4,4′‐bis(1‐naphthoxy)‐diphenylsulfone with TCTPC by electrophilic Friedel‐Crafts acylation in the presence of DMF with anhydrous AlCl₃ as a catalyst in 1,2‐dichloroethane, respectively. These polymers having weight–average molecular weight in the range of 76,600–83,900 are all amorphous and show high glass transition temperatures ranging from 213 to 250°C, the 5% weight loss temperature over 450°C, high char yields of 60–67% at 700°C in nitrogen and good solubility in CHCl₃ and polar solvents such as DMF, DMSO, and NMP at room temperature. All the polymers formed transparent, strong, and flexible films, with tensile strengths of 85.1–90.8 MPa, Young's moduli of 2.52–3.24 GPa, and elongations at break of 21.2–27.2%. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Nucleophilic Displacement Polymerlzation of N,N'-BIS(p-Chlorobenzylidine)-4, 4'-Diaminodiphenyl Ether with Sodium Sulfide

A novel poly(Schiff-base sulfide) polymer was synthesized by nucle-ophilic displacement polymerization of N,N'-bis(p-chlorobenzylidine)-4, 4'-diaminodiphenyl ether with sodium sulfide in anhydrous condition. The resulting polymer was soluble in some aprotic solvents having inherent viscosity of 0.18 dL/g in dimethylacetamide at 30°C. The monomer and the polymer were characterized by elemental analysis, infrared, and ¹H NMR (nuclear magnetic resonance) spectroscopy. The thermal characteristics of the polymer were also studied by thermo-gravimetric analysis and differential scanning calorimetry. The temperature of 10% weight loss, glass transition temperature (T _g). and crystalline melting point (T _m) of the polymer were found to be 420, 91.89, and 38575°C respectively.     

Synthesis of poly(ether amide)s from p‐xylylene glycol and bis(ether nitrile)s

BACKGROUND: Poly(ether amide)s have been well studied in terms of improving the physical and thermal properties of aromatic polyamides. Poly(ether amide)s of high enough molecular weight to be useful for industrial purposes are generally difficult to prepare. The objective of this project was to introduce a simple and commercially feasible process to prepare poly(ether amide)s by a polymerization reaction at relatively low temperature. RESULTS: A series of poly(ether amide)s were prepared by direct polyamidation of p‐xylylene glycol with bis(ether nitrile)s via the Ritter reaction using concentrated H₂SO₄ in acetic acid. The synthesized poly(ether amide)s showed good solubility in polar aprotic solvents. The resultant poly(ether amide)s had inherent viscosities in the range 0.36–1.03 dL g^?1. The glass transition temperatures of the poly(ether amide)s were determined using differential scanning calorimetry to be in the range 190–258 °C. Thermogravimetric analysis data for these polymers indicated the 10% weight loss temperatures to be in the range 290–390 °C in nitrogen atmosphere. CONCLUSION: The Ritter reaction was applied for the synthesis of a variety of poly(ether amide)s with moderate to high molecular weights. This procedure provides a simple polymerization process for the convenient preparation of poly(ether amide)s in high yield at room temperature. Copyright © 2009 Society of Chemical Industry